Search Documents

By Yehia M. Youssef, Nourhan Moukhtar, M. H. Abdel-Aziz, Ibrahim Hassan

Copper was recovered from copper sulfate solution in a batch-recycled galvanic reactor operated under forced convection with the generation of electrical energy during the cementation process. The divided galvanic cell consisted of parallel copper and zinc plates. The mass transfer rate and the amount of electrical energy generated were found to be directly proportional to the solution flow rate and the initial concentration of metallic ions and inversely proportional to the distance between electrodes. The experimental results were expressed in terms of a dimensionless correlation including all parameters. The wastewater treatment presented herein cell can be utilized to recover many soluble heavy metal ions from solution with high efficiency.

Oct 2, 2020

By G. A. Mallory

"The South Bay Division of Selco Mining is located fifty-four miles northeast of Ear Falls Ontario on Confederation Lake. The concentrator operates five days a week and processes six hundred tons per day of copper zinc silver sulphide ore. The concentrator is comprised of crushing, grinding, differential flotation, thickening and drying circuits. The major constituents of the concentrator feed are: chalcopyrite 7%, sphalerite 20%, pyrrhotite 3%, pyrite 25 - 30% and felsitic volcanics 40 - 50%. The mine went into production in March 1971 with an anticipated three year life and is now scheduled for closure in the summer of 1981. Recent mine production has been limited to three cut and fill stopes which have widely varying ore grades, therefore mill feeds vary from 0.25 to 4% copper, 3.5 to 27% zinc, 0 to 0.4% lead and 15 to 30% iron.In mid 1977 Selco negotiated a six month rental purchase agreement with Outokumpu Instruments Canada Limited for a five stream analyser system. The Minexan 202 probes were the first Outokumpu probe type analysers installed in Canada although Outokumpus' Courier systems are well known. Installation of the system took place in April 1978 and after numerous hardware faults the six month evaluation began in August. By December it was obvious that the Minexan 202 probes with proportional detectors did not have adequate resolution to determine low copper values in either of the tailings streams. Outokumpu offered to replace the tailings analysers with a new prototype solid state detector probe the following summer. The evaluation on the five Minexan 202 probes continued until August 1979 when the new solid probe was installed. The Minexan S (solid state) probe was evaluated with the three remaining Minexan 202 probes until December 1979 when Selco elected to purchase the system."

Jan 1, 1981

By J. Chenier, M. Boissoneault, D. Ducharme, R. Schonewille

The operation of Falconbridge's Sudbury nickel smelter has undergone significant change since the production was consolidated to a single electric furnace in 1994. In the late 1990's a capital program of about $100 MM (Cdn) was undertaken to expand and modernize the smelter. This project, known as Smelter 2000, was mainly driven by the need to process the new concentrate produced at Falconbridge's Raglan operation in northern Quebec. Included in the scope of the project was the installation of dry concentrate handling facilities, modifications to the roaster feed preparation system, installation of a matte granulation system and modification of one of the converters. Improvements to in-plant hygiene were also an important part of the Smelter 2000 project. Over the past 5 years much has been learned about the challenges in treating two significantly different concentrates. More recently, the introduction of a third concentrate from Falconbridge's new Montcalm operation near Timmins, Ontario has added another dimension to the operation. This paper will describe how the main challenges from the past 7 years have been overcome and discuss the path forward for the Sudbury Smelter Business Unit.

Jan 1, 2005

By J. Cooperman

THE INVESTIGATION was carried out in three stages, depending on the objectives of the work and the kind of equipment used. The first stage involved testing of 11 representative Alabama coals, the source of which is given in table 1. The objective was to find whether these coals could be gasified raw by the Lurgi method, and the equipment used was a 4-inch batch generator (to be described later). This generator proved too small and difficult to control to provide adequate amounts of products under continuous operating conditions for testing. For the second stage, a 6-inch batch generator was used, which was provided with facilities for superheating the steam-oxygen mixture and for synthesizing additional methane from the residual carbon monoxide and hydrogen in the primary Lurgi gas. Selected Alabama coals, Pittsburgh-bed coal from West Virginia, "Disco," and anthracite were used. For the third stage of the work, a continuous generator of 1 square foot grate area, following closely the design of the industrial generators operated in Germany, was provided. This generator was designed by 0. Hubmann, engineer for the Lurgi company, and was expected to give results closely simulating industrial-scale apparatus. The purpose of this equipment was to test prepared materials shown to operate smoothly in the 6-inch generator under conditions approximating as nearly as possible those prevailing in industrial practice. Work of the first stage showed that Alabama coals could not be used in the Lurgi process without first destroying the coking power.

Jan 1, 1951

By Gabriel Burlandy Mota de Melo

Manchas de óleo em um meio aquoso foram removidas utilizando compósitos de parafina com nanopartículas de ferritas de cobalto (CoFe2O4), níquel (NiFe2O4) e níquel-zinco (Ni0,7Zn0,3Fe2O4), nas proporções de 13,0% e 28,5% em peso. Para avaliar a eficiência da remoção, foi determinada a velocidade dos compósitos ao serem acoplados a uma mancha de óleo na superfície da água e submetidos ao campo magnético de um imã permanente. O melhor desempenho foi obtido com o compósito de parafina contendo 13,0% em peso de ferrita de níquel-zinco.

Aug 16, 2017

Provide optimum visibility of mining operations while maintaining protection and comfort for ma-chine operators. Approach Cabs and canopies with hydraulically powered variable-height control were developed for several machines and tested in underground mining operations. How It Works From his position in the cab, the operator can raise or lower the cab, selecting a height that offers either more visibility of the working place or greater clearance for tramming. The entire cab enclosure moves up and down on guide rollers that ride on a pair of rails, and is actuated by a hydraulic cylinder controlled from within the cab. Normal working heights, for each of the four different cabs developed, are with the cab bottom from 6 to 8 inches above the mine bottom. A typical range of elevation (excursion) afforded by this design is shown in Figure 1.

Jan 1, 1978

By Luzheng Chen

Pulsating high-gradient magnetic separation (PHGMS) of fine hematite from tailings was studied using a pilot PHGMS separator to investigate the possibility of its application in industry. The results of this investigation indicate that PHGMS is effective for recovering fine hematite from the tailings and greatly improved the separation performance compared with the conventional high-gradient magnetic separation at the same conditions. By applying the pilot separator with a 1-mm rod matrix to a tailings containing 28.76% Fe, a concentrate assaying 54.35% Fe with 35.89% recovery was achieved. It was found that the separation performance of the pilot separator closely correlates with the main pulsating parameters, i.e., pulsating stroke and frequency. It was also found that a change in the wire diameter of the rod matrix from 2 to 1 mm causes a weak drop in concentrate grade but results in a considerable rise in recovery. This finding proves that the improved performance achieved by the pilot separator is attributed to the pulsating of slurry and to the use of a 1-mm rod matrix. When the first commercial SLon-2500 PHGMS separator with a 1-mm rod matrix was applied to recover fine hematite from the tailings, the results duplicated those achieved with the pilot PHGMS separator.

Jan 1, 2009

By Timothy P. Smirnoff, Tracy K. Lundin

INTRODUCTION The City of Phoenix, Arizona is located in the Phoenix Basin watershed which is prone to flash flooding several times each year. The runoff from these storms moves from the mountains in the north to the Salt River in the south. An extension of Interstate Highway 10 (1-10) will pass through the city east to west to form an Inner Loop through the downtown business district. PROJECT DESCRIPTION The I-10 Inner Loop extension will be a depressed roadway which would intercept the surface drainage of the Phoenix Basin and separate the watershed into two regions. To prevent flooding of the depressed roadway, runoff storm water collected from the northern half of the drainage area will be conveyed beneath the roadway to its natural outlet at the Salt River. A conveyance system composed of pressure tunnels beneath the city, shown in Figure 1, was proposed to achieve this goal . Table A presents the prominent features of each of the tunnels. This paper will describe geologic and engineering parameters specific to Phoenix which were used in the design of a series of tunnels to convey storm water from the I-10 Inner Loop to the Salt River. The design of tunnel initial and final support is described along with support and construction methods used by the Contractor.

Jan 1, 1985

By P. H. Floyd

This report presents the results of laboratory and continuous mill-beneficiation tests conducted at the Bureau of Mines Northwest Electra Development laboratory, Albany, Oreg., on nonsulfide lead ore from the Sherman mine, Leland district, near Burke, Idaho. The predominant lead-bearing mineral in the ore sample treated was pyromorphite, a minor ore mineral of lead. Known reserves of pyromorphite lead ore in the United States are limited, although an appreciable tonnage of this type of ore is found in the Sherman mine. Very little pyromorphite is being mined in this mine or in the United States. This beneficiation problem presented a unique opportunity to study the mineral-dressing properties of a less widely known lead mineral, and consequently adds valuable knowledge to the ways of beneficiating ores containing nonsulfide lead values. This mineral-dressing problem was successful with conventional concentration methods of flotation and Gravity separation.

Jan 1, 1952

Reduce the potential for injuries in underground mines by providing an alternative to manually lifting and holding heavy roof-support beams. The Problem I-beams, rail sections, and wooden cross-beams are often used in mine haulageways where extensive roof support is needed. Studies by the Bureau of Mines have shown that many mines must resort to manually lifting, moving and installing these beams. Such manual-handling activities have the potential for causing injury to mine workers, particularly back injuries. I-beams used for roof support can typically weigh from 400-500 lbs. Rail sections weigh about the same as the I-beams. Wooden beams can weigh from 200 to 300 lbs. To lift a single beam usually requires the efforts of 3 to 5 mine personnel.

Jan 1, 1988

By S. Vorberg, J. Preussner, B. Fischer, U. Glatzel, R. Völkl, M. Wenderoth

Pt-Al-X alloys have shown good mechanical properties and adequate oxidation resistance. Starting from a promising Pt-Al-Cr alloy, the influence of Ni additions was investigated. After ageing finely dispersed precipitates are observed. Nb, Ta, Ti and Re increase strength when added as partial substitute for Al. Minor additions of B increase creep resistance and rupture time remarkably, owing to strengthening of the grain boundaries. The evolution of the alloy development programme as well as selected properties of the multi-component Pt-base alloys are presented.

Jan 1, 2006

By Daniel K. Lindberg, Fiseha Tesfaye

To reduce the use of fossil fuels and increase self-sufficiency in energy, nowadays, there is an increasing interest to produce heat, power and transportation fuels from renewable resources. Solid biomass is one of the most important renewable energy sources for meeting this target. However, fouling, slagging, and corrosion threaten long-term operation availability and costs of biomass power plants. Slags accumulated on the surfaces of superheaters, which decrease thermal efficiency, often constitute a considerable percentage of complex inorganic phases. However, thermodynamic properties of the complex inorganic phases and their combined effect, which will help to deal with the slag related problems during high-temperature biomass combustion processes, are not well known. In the present paper, thermodynamic properties of K-, Ca-, and Na-based inorganic phases and their mixtures under different gas conditions are both critically reviewed and experimentally studied. The obtained results are presented and discussed.

Mar 1, 2017

By P. A. Croce

A total of 17 mine gallery fire tests (23 including sub-tests) were completed during this report period (10/1/76 - 11/30/77), directed at identifying a hazardous timber-set fuel-loading in a mine passageway that is otherwise free of combustibles. Results of these initial tests show that the capability of a particular fuel loading for propagating a fire is dependent upon the imposed ventilation air velocity and the ignition intensity, although this dependency needs to be better defined. It is also apparent that care must be taken when relating gallery test fire behavior to actual mine fire behavior, because of the restrictive length of the gallery. Present data indicate that some modification to the instrumentation scheme may be advantageous before proceeding with future tests.

Jan 1, 1978

By S. Christiansen, G. R. Winslow, R. W. Kobler

Todays End of Life vehicles are shredded and their metal components recovered and recycled by standard methods. The remaining non-metallic fraction is shredder residue, and contains vast amounts of high value engineering plastics. None are today recovered. Discussed are the developmental approaches used in the first process to recover these valuable plastics. Examined are initial laboratory studies, pilot plant design and construction, product development, results, and flowchart explanations.

Jan 1, 2001

By Brian P. Waagner

Construction law in general and the law of deep foundations in particular continues to develop rapidly, particularly in the areas of risk allocation. Public and private owners are increasingly using contractual disclaimers to shift the risk of differing site conditions to contractors, and courts are increasingly willing to enforce these contractual devices. Perhaps also in an effort to control costs, public and private owners are turning to design-build contracting techniques. While design-build offers many advantages over traditional project delivery systems, it does not answer all of the risk-allocation questions that frequently arise. Even in design-build, problems with unanticipated subsurface conditions and defective design are not easily addressed. Finally, developments in electronic commerce present the potential to transform the construction industry.

Jan 1, 2002

By Thomas C. Shapiro

Introduction In recent years - even months - the number of articles on computers has increased rapidly. One can hardly pick up a newspaper or magazine without seeing a computer-related article. The article usually explains how the computer will change our lives. Many of us have some concern about the nature and type of change. For most of us, though, the problem is lack of information and understanding about how computers work. In other words, how do we make cost-effective decisions about computers? This three-part series will explain, simply, what a microcomputer is, how it works, and how to decide if you need one. This first article will define terms and briefly discuss areas where computerization might be economic. The second article will discuss geology and mining applications. The third article will discuss plant, administrative, and geotechnical areas as well as the future of software development in the minerals industry. Terms and Concepts All computers have input and output devices and a central processing unit (CPU). Information - instructions and data - is communicated to the computer by means of input devices. These instructions to the computer are converted into language that the computer understands. This causes the instructions to be carried out in the CPU. The result of these operations is translated back into language that we understand. This information is then sent to output devices such as printers and video display tubes. Traditionally, peripherals were devices separate from the main-frame (the CPU and memory) and were used to input, output, and store information or instructions. Today, peripherals perform the same functions though they may be housed in the same cabinet as the CPU and memory. Historically, peripherals included all input and output devices not part of the mainframe. Input devices include keyboards, magnetic tape, and card readers. Tapes and disks are input as well as output devices. Output devices are printers, CRTs (Cathode Ray Tubes), and any mass storage device capable of storing data when directed to do so by the computer or the program. In fact, any mass storage device that can give the computer data when requested is an input device. Mass storage devices include floppy disks (thin, round sheets of plastic covered by metal particles), and hard disks. The latter are thicker and more densely coated with metal particles. This allows much more information to be stored. Another type of mass storage is magnetic tape. Its type and size varies widely. Processing and Storage Any computer understanding must include how instructions and data are processed and stored. Information is stored as a positive or a negative field known as a "bit." There are eight bits in a byte. The bits can be represented as either a one or a zero. Thus the code for a byte representing the numeral one is 00110001. The byte representing the letter A is 01000001. These codes are from the American Standard Code for Information Interchange (ASCII). ASCII defines the standard set of characters including alpha, numeric, and special characters. The computer's memory has allocated locations where instructions as well as incoming information can be stored. All information and instructions are stored as binary numbers bit by bit - zeros and ones. The amount of data that can be stored is referred to as either thousands or millions of bits or bytes. The letter "K" is used to designate one thousand units. The letter "M" is used to mean one millon units (one meg). Disks Thus, a 113-mm (5 1/4-in.) floppy disk - double sided and double density (DSDD) - contains 320,000 bytes (characters) or 320K. This is about 164 double-spaced, type-

Jan 2, 1984

This publication summarizes the Bureau's activities as part of a study of the Juneau Mining District (JMD) during the period 1984-1988. The objectives of the program were to identify the type, amount, and distribution of mineral deposits in the district, determine ore reserves, study beneficiation technologies for the ore, make feasibility studies, and address economic and legislative effects on mineral development. The JMD study was a cooperative study involving the Bureau and the Alaska Division of Geological and Geophysical Surveys (ADGGS). Over 30 employee-years were spent by the Bureau on this project. Bureau investigations in the JMD consisted of a district-wide investigation of industrial materials in addition to site-specific investigations of precious and base metals in five subareas. During the 4 years of the JMD study, more than 300 areas, mines, prospects, and occurrences were visited, which contain gold, silver, copper, zinc, lead, nickel, cobalt, tungsten, molybdenum, chromium, and platinum group metals (PGM). More than 59,000 feet of underground workings were mapped and sampled. More than 5,500 samples were taken; one diamond drilling program and three geophysical surveys were completed. An up-to-date and complete mineral data base for the JMD did not exist prior to this study. The JMD study, which coincided with a tremendous increase in mineral interest and activity in the district, has proven to be valuable to both the minerals industry and land management agencies. The discovery of two new mineral occurrences and compilation of data on known mines, prospects, and occurrences have aided industry activity in the region. The study enabled timely data to be available to land management agencies at the Federal, State, and municipal levels.

Jan 1, 2012

By Lane White

In mid-April 1992, MINING ENGINEERING mailed a survey questionnaire relating to mining shovels and hydraulic excavators to 125 SME members working at surface mines or at the headquarters of companies that operate surface mines. The mailing was directed to individuals whose titles indicate that they have management or mine planning responsibilities for surface mining operations. A total of 56 usable surveys returned by June 17 are the basis of this report. Precious metals mines Eighteen precious metals mines or mining companies returned completed surveys in time to be included in this report. Of these, 14 use hydraulic shovels only for both ore and waste, I uses both hydraulic and rope shovels, and 2 use Caterpillar 988 front-end loaders for both ore and waste. (Of the latter 2, neither expects to be in the market for a shovel in the next three years. I of these 2 placed Harnischfeger P&H number one and O&K number two in response to the question, "Based on your current knowledge of their machines, which manufacturer would you likely chose to supply new shovels or excavators to a mine or mines operating under your responsibility, if you were in the market?") Another uses front-end loaders, make not designated. The latter does not expect to be in the market for mining shovels or excavators within the next three years. Of the final total of 14 precious metals mines using only hydraulic excavators to load ore and waste, 8 use Hitachi excavators only, 1 uses Demag excavators only, 1 uses Liebherr excavators only, 1 uses O&K excavators only, 1 uses Harnischfeger P&H and O&K excavators, 1 uses Harnischfeger P&H and Hitachi excavators, and 1 uses Hitachi and Demag excavators. Of the 14 precious metals mines using only hydraulic excavators, 7 use excavators in the 7.6 to 11.5 m; (10 to 15 cu yd) size range. Of these 7, 5 use only excavators in this size range, and they are used to load both ore and waste. 1 of the 7 also uses 11.5 to 17 m' (15 to 22 cu yd) excavators, and I also uses a 17 to 23 m3 (22 to 30 cu yd) excavator. Of the 7 remaining of these 14 precious metals mines that use only hydraulic excavators, 3 use 11.5 to 17 m' (15 to 22 cu yd), 2 use 17 to 23 m3 (22 to 30 cu yd), and 2 use less than 7.6 m' (10 cu yd) units.

Jan 1, 1992

Attempt has been made to determine the nature of charge on activated carbon surface by studying the electro-kinetic properties of the carbon in the presence of cations, anions and aurocyanide solutions. The zeta-potential measurements were made in the presence of individual ions and also in combinations. The cations and anions chosen were those commonly associated with gold bearing ores in Kalgoorlie area. It was found that the iso-electric point of Norit Carbon was at pH 4.45; below this pH the charge was positive, while above, it was negative. In the absence of gold cyanide solutions and in the presence of individual cations the i.e.p. shifted to the alkaline range (pH 7.2-8.5) while in the presence of anions the i.e.p. was shifted to less than pH 3.5. In the presence of aurocyanide solutions, the iso-electric point was still in the acid region irrespective of whether anions or cations were present. The probable mechanism for such a behaviour has been attempted after measuring the specific conductivities of solutions before and after gold adsorption, by studies using the electron- probe-mirco-analyser, and S.E.M. on the carbon surface.

Jan 1, 1982

"The success or failure of coal mining operations in Western Canada may hinge on the ability to extract thick coal under a variety of geological and mining circumstances and conditions. The paper presents, in who-where, what- how pattern, the current status of undergrounud mining of thick coal seams based on a review of foreign technical literature. The underground production of coal from what are considered to be thick seams is over 300 million tons per year. Methods of mining have evolved, through years of trials and tribulations, capable of meeting the requirements of a modern mine: high bulk outputs from a limited number of mining faces by concentrating in the horizontal (mechanization) and in the vertical (increased working lift)."

Jan 1, 1972