Search Documents

By Zia Zafir

Design of the deep foundations for the loads imposed by lateral spread include the estimate of the pressure applied by the liquefied material as well as amount of anticipated displacement. In the absence of a non-liquefiable cover over a liquefiable layer, it is possible to design the foundation system just for the additional pressure applied by the flow slides. On the other hand, if a non-liquefiable layer exists above the liquefied zone, the foundation should be designed for anticipated movements. To completely account for liquefaction and/or lateral spread and their interaction with the deep foundation system, a coupled soil-structure interaction (SSI) analysis should be performed. However, a complete SSI analysis may not be feasible for most of the projects. This paper will present recent advances in analysis techniques and simplified methods to design deep foundations for liquefaction and lateral spreading. In addition, a case history of the Rancho California Bridge in southern California located within 1 km of the active Elsinore fault will be presented. One of the bridge abutments is underlain by potentially liquefiable layers. The pressure applied by the liquefiable layer was estimated to be greater than the shear capacity of the 36-inch CIDH piles designed for the abutment. However, with limited ground improvement and more careful analyses incorporating structural effects of CIDH piles, resulting design and construction resulted in a factor of safety greater than 1 against slope failure. The recommended approach was generally consistent with the recently published, and AASHTO sponsored, NCHRP 12-49 project regarding seismic design guidelines for new bridges and the effects of seismic displacements against bridge foundations.

Jan 1, 2006

By Baha Abulnaga

Slurry pipelines are used in a number of countries to convey processed ore mixed with water over long distances from remote mine sites to ports or plants for further processing. In Egypt and Sudan, numerous mineral resources are scattered in remote areas. Through the years, Egyptian geologists have identified 268 sites for metallic ores and 386 sites for industrial nonmetallic minerals. A large portion of these sites are in the Eastern Desert in an area called the Nubian Shield. Similar sites are found in the Sudan where mining contributes to less than 1 percent of the gross domestic product (GDP). There are three important components of infrastructure needed to develop these resources ? power, water and transportation. While Egypt is able to satisfy 70 percent of its needs in iron ore from the Gadideh Mine in the Western Desert, it needs to expand its other resources to reduce imports heavily sedimented. Dredging of these sediments and transporting them by slurry pipelines would enhance an industry of bricks or agricultural development based on tailings technology often used in mining. This article explores the potential for slurry technology for opening new mines in the desert or recuperating the sediments of the Nile. The technology by itself would be new to both countries and would benefit from collaboration, particularly to de-silt the Nasser-Nubia Lake.

Jan 3, 2010

By R. B. Stotelmeyer

Mineral resources, or a potential for their discovery, occur at 34 localities in the Glacier Peak Wilderness and adjacent areas of the north Cascade Range of Washington (see plate). Eighteen of the mineral deposits are in the established Wilderness, four are in or partly in contiguous RARE II (Roadless Area Review and Evaluation) lands recommended by the Forest Service for addition to the Wilderness (A, D and G6031.), three are in adjacent RARE II lands excluded from wilderness consideration, and nine are in nearby roaded areas excluded from the RARE II inventory. Mineral commodities that might be produced from the Wilderness and recommended additions are gold, silver, copper, lead, zinc, molybdenum, arsenic, cadmium, tungsten, cobalt, limestone (marble), pumice, and volcanic cinders. Mineral production from adjacent lands might include most of these commodities, plus antimony, decorative stone, pyrite, silica, and garnet.

Jan 1, 1982

By Cadia Geology Team

The Cadia Hill Gold Mine, located near Orange in Central Western New South Wales, is owned and operated by Cadia Holdings Pty Ltd, a wholly owned subsidiary of Newcrest Mining Limited. Construction including pre-strip mining occurred from 1996 to 1998. The mine was officially opened in October 1998 following commissioning of the concentrator and mine fleet in June of that year. The Cadia Hill orebody is a porphyry related gold and copper system. The final pit has a strip ratio of approximately 1.3:1.0. Mining is undertaken on 15 metre benches using large capacity diesel hydraulic face shovels at an annualised rate of up to 70 Mtpa. The concentrator is currently rated at 17Mtpa and includes the worldÆs largest single line grinding circuit. The feasibility Mineral Resource was estimated at 352 Mt at 0.63 g/t Au and 0.17 per cent Cu. Initial reserves totalled 200 Mt at 0.74 g/t Au and 0.17 per cent Cu yielding a mine life of approximately 12 years. During the pre-production period mine geology systems were developed to support the operation. By design these systems were intended to add value to the business through minimisation of material miss-classification, provision of accurate and timely production information and mapping and reconciliation as a continuous model improvement tool. Variances that would prove to be material to the life of mine plan were recognised during the first year of production. These included identification of additional ore tonnes, higher copper grades and higher gold recoveries relative to the model. Gold grades and copper recoveries also reconciled favourably. Testwork was undertaken to determine the underlying causes of each variance. Re-modelling was then undertaken to capitalise on those variances. The Cadia Hill Gold Mine life of mine plan was re-evaluated with updated geology, grade, geotechnical, metallurgical and environmental inputs. Operating strategies were also reviewed and revised. Despite application of reduced metal prices in the evaluation, the outcome was one of extended mine life with more metal produced at lower cost. Development of robust mine geology systems, including a pro-active reconciliation process contributed to tangible improvement of the Cadia Hill Gold Mine operation. On-going system development and improvement initiatives are planned to add further value for the future.

Jan 1, 2000

By Betty Gibbs

The Ore Body Modeling and Mine Planning Worshop, sponsored by the Society for Mining, Metallurgy, and Exploration, Inc. (SME), was held Feb. 22-24, 1991 before the SME Annual Meeting and Exhibit in Denver, CO. More than 40 people from mining companies, government agencies and universities attended. Eight vendors of integrated ore body modeling and mine planning software attended and presented the results of problem sets given before and during the workshop. They were: [ ]

Jan 1, 1991

By Diego Pinheiro Aun

Neste trabalho, foi investigada a influência da textura de fitas de NiTi superelástico no início do processo de cristalização de um revestimento de TiO2 flexível. Foram utilizadas a calorimetria diferencial, cartografia Raman e difração de raios X para o estudo. Foi mostrado que existe uma influência significativa da textura do substrato no crescimento de grãos de anatase e rutila no filme de TiO2. Amostras com menor rugosidade apresentaram grãos mais desenvolvidos para todas as temperaturas de cristalização. Mostrou-se também que o substrato de NiTi promoveu a formação de TiO2 rutila em temperaturas abaixo daquelas observadas para a cristalização de pós.

Aug 16, 2017

By Laurence McGonagle

"The Highland Uranium Project (HUP) is located approximately sixty miles northeast of Casper, Wyoming and is owned and operated by Power Resources, Inc. (PRI). With an annual production of680 tonnes (1.5 million lbs) U308, HUP is one of the largest uranium producers by in-situ leach (ISL) in the western world. Uranium is currently produced from four wellfields with a total flow rate of approximately 1,135 m3/hr (5,000 gpm). The carbonate leach solutions are processed by anion ion exchange at two satellite facilities located in close proximity to the wellfields. The loaded resin is transported by truck to a central processing facility for elution of the uranium. Uranium in the pregnant eluant is precipitated and washed prior to calcining.Wastewater from the satellite facilities is treated and used for irrigation at a Land Application Facility. The wastewater generated at the central processing facility is injected into a 2,750 m (9,000 ft) deep waste disposal well.When economical mining of the orebodies is complete, restoration of the groundwater is initiated. There are currently two wellfields at HUP undergoing ground water restoration. Phase I restoration consists of removal of the carbonate leach solution from the ore body. Phase II includes treating the withdrawn fluid with reverse osmosis and reinjection of the permeate into perimeter wells.Future plans include construction of additional satellite facilities at the Gas Hills Project and other economical deposits located within 240 km (150 mi) of HUP. The capacity of the central processing facility will be increased to 1,815 tonnes (4 million lbs) U308 per year by late 1999."

Jan 1, 1998

By M. D. Budeba

Determining the efficiency of a surface coal mine operation is an essential activity, which can help in deciding on the optimal use of input resources, including effective capital allocation, in generating a desired quantity of coal of a specific quality. Mines operate today in challenging conditions, with diminishing reserves of high-quality coal, remote location of new coal deposits, infrastructure problems, environmental legislation, and the effects of climate. All these have an impact on the performance of a mine. Given such challenges, a company has to be technically efficient compared to other existing coal producers in order to generate profits. It can use the measurement of its efficiency to evaluate its productivity, benchmarking this against the best-performing mines and determining optimal variables in order to minimize slack and achieve the desired outputs. This paper discusses the use of Data Envelopment Analysis (DEA) in evaluating the efficiency of a surface coal mine supply chain for the coal export market. The supply chain is considered to be composed of subprocesses that are modelled as a multistage system. Numeric examples will be used to illustrate the application of DEA.

Jan 1, 2014

By Steve Colburn

The CRITERION Survey Systems utilize both theodolite mounted and hand held reflectorless distance meters. These are eye safe, easy-to-use, and specifically designed to endure the harsh environments characteristic to the mining, quarry and explosives industries. Survey data collected by the systems is digitally stored in a ruggedized data collector and then processed with a specialized, Windows-based, interactive software program which can be run on any standard PC.

Jan 1, 1997

By M. D. G. Salamon

It has been noted in recent years that the pillars in some bord-and-pillar workings scale or spall. In due course this process may result in the collapse of the affected panels. This paper presents a methodology for assessing the long-term behaviour of such workings, employing a simple model of pillar deterioration by scaling. It is assumed that scaling causes a gradual reduction in pillar width, hence the safety factor of pillars reduces in time. It is also postulated that the process of scaling will be arrested if the coal rubble around the pillar reaches a critical height. The probability that the pillars will survive for a certain period of time, or indefinitely, can be estimated. This can be accomplished by using the log-normal distribution proposed by Salamon and Munro4todescribe the distribution of the apparent safety factor values at failure. If an estimate of the rate of scaling is known, it is also possible to quantify, using a Monte Carlo technique, the expected life of the pillars. The method also facilitates pillar design by specifying a probability of survival for a given number of years or, alternatively, for an indefinite period. Using the limited pool of available data, analyses show that the proposed model does not appear to be inconsistent with observed behaviour of pillars in the Vaal Basin. The crucial parameter is the rate of scaling. Back calculations from eleven cases suggest that the rate of spalling in the Vaal Basin is about 0.2 m/year. It is noteworthy that two further cases in the same area give significantly higher rates (0.85 m/year). Some underground observations in the Witbank area indicate considerably lower rates in the order of 0.02?0.04 m/year. Further areas for study are recommended. These include a study of old workings to determine the extent and rate of scaling in the various coal fields, an investigation into the possible relationship between scaling and the chemical composition of the coal. In addition, model studies will be required to assess the practical impact of the research findings.

Jan 1, 1998

By S Jackson, I Arbuthnot

The use of High Rate Thickeners has gained wide acceptance in the mineral treatment industries. The design of these units is characterized by an efficient deaeration and flocculation chamber, and introduction of the flocculated feed solids into a preformed floc bed zone. By these means the settling process is accelerated and consequently High Rate Thickeners achieve a significantly higher throughput per unit area than conventional thickeners.   The object of a control system on a High Rate Thickener (HRT), as on a conventional thickener, is to obtain the required underflow density and overflow clarity at all feed conditions. The feed conditions which may vary include volumetric and mass feed rate, pulp density, particle size and particle type. A conventional thickener has a large volume and cross sectional area, and changes in performance occur slowly û the operator has time to observe and react to these changes to maintain control. On a HRT, there is a much reduced residence time and therefore control parameters need to be reset more frequently. Although manual control is possible, the use of automatic control systems is therefore desirable to avoid excessive operator attention, while optimizing control of density and clarity. Automatic control of a conventional thickener is usually achieved by an underflow density loop which regulates the rate of withdrawal of underflow. A turbidity meter is sometimes used to measure overflow clarity and regulate the addition of a coagulant or polymer flocculant. These measures are not adequate on a HRT, because they would not give optimum control and could lead to excessive flocculant use. To achieve optimum operation in a HRT, the floc bed level should be maintained above the feed inlet point in the thickener. This bed level has become the key variable around which most control systems have been designed. However, a number of problems have occurred which has resulted in poor control, or only partial control of thickener performance. We will describe some of these problems, and a solution which is simple and effective.

Jan 1, 1990

By Joseph M. Kuchta

The limits of flammability and minimum autoignition temperature of a fuel are important elements in assessing fire and explosion hazards that may exist when using or handling the fuel. The limits of flammability define the range of compositions of the fuel gas or vapor mixed with an oxidant through which a flame, initiated by an outside energy source such as an electrical spark, can propagate. The minimum autoignition temperature (M.A.I.T.) is the lowest temperature at which the fuel vapors ignite spontaneously in a specified medium; in this case the ignition energy is supplied by the heat content of tae environment. This temperature is also referred to as S.I.T. value by some authors. Because the autoignition of a fuel also depends on the time interval during which the fuel is subjected to heat, ignition delays are significant. Ignition delay is defined here as the total time elapsed between the introduction of the liquid fuel into the oxidizing atmosphere and the appearance of a flame. This time interval includes both the physical and chemical processes leading to ignition. The ignition delay is usually maximum at the M.A.I.T, and decreases as the temperature of the system is increased. The flash point and the fire point are also useful in assessing the fire and explosion hazards of a fuel. The flash point is the lowest temperature at which saturated, flammable fuel vapor-air mixtures are formed at atmospheric pressure and, therefore, it is essentially the lower limit of flammability

Jan 1, 1962

By George T. Faust

The petrographer engaged in examining the products resulting from the beneficiation of ores, and rock minerals is constantly required to develop new means acid methods of assaying microscopically the results of such operations. From time to time investigators have published descriptions of apparatus that have aided in solving problems in processes of physical separation. Thus, in 1919, Coghill and Bonardi 3/ published a paper covering the application of the binocular microscope and camera lucida to the microscopic analysis of pulverized ores. Similar work has been published by Schneiderhohn 4/ Schwartz 5/, and Head and his associates 6/, 7/, 8/. The present paper goes further and considers application of the polarizing comparison-microscope to problems directly concerned with mineral dressing where it is desirable to compare analogous products, and in addition it suggests new uses in various related fields. This work was conducted under the cooperative agreements of the Southern Experiment Station of the Federal Bureau of Mines and the University of Alabama.

Jan 1, 1940

By R. W. O. Kersten, J. D. Austin

A questionnaire was circulated in 1986 that had the objective of establishing the type of material that members would like to see featured in the Journal of The South African Institute of Mining and Metallurgy. The questionnaire contained five main questions involving the following:

Jan 1, 1987

By Gunnar Nord

Introduction ??Atlas Copco has customers both amongst Miners and Contractors ??We believe that the contractor's approach to tunnelling is worthstudying ??For a tunnel contractor the incentive is speed as ?30 % of the costs are material related ?70 % of the cost are time related ?A tunnel contractor favours utilizing of the face ?A miner favours utilizing of the gear ??Statement; In mining, a long term average advance rate of more than 10 m / day can be achieved with the excavation techniques availabletoday

May 1, 2009

Mine waste and mine reclamation are topics of major interest to the mining industry, the government and the general public. This publication and its companion volume are the proceedings of a conference held in Pittsburgh, April 19-21, 1988. There were nine sessions (50 papers) that dealt with the geochemistry, hydrology and problems of mine waste and mine water, especially acid mine drainage. These comprise Volume 1. The nine sessions (43 papers) that dealt with reclamation and restoration of disturbed lands, as well as related policy issues, are included in volume 2. Volume 2 also contains the ten papers that pertained to control of subsidence and mine fires at abandoned mines. Poster session presentations are, in general, represented by abstracts; these have been placed in the back of both volumes.

Jan 1, 1988

By George Koenig

I have been granted the outstanding privilege... and pleasure to introduce you this evening to the Grand-Duchy of Luxembourg and to tell you in a few words how this country came into existence, how it managed to survive and what role it nowadays plays in the International Community. Luxembourg, situated between Belgium, Germany and Prance is a small, a very small country... just a dot on a map. After all, it is only a matter of 62 miles from top to bottom and 37 miles across at it's widest... barely covering some thousand square miles... so be careful about stepping on the accelerator... you might be in and out without having realized it... which would be a real shame as the Grand-Duchy enjoys a fairly unique geographical feature in so far as it provides the visitor with an outstanding variety of scenery concentrated in a minute spot.

Jan 1, 1987

By Tony S. Calayag

Throughout the mining industry today, new bearing materials - ZA* high-performance zinc-aluminum alloys - are reducing costs of maintaining and rebuilding a wide range of equipment. As replacements for bronze bearings, installed in original equipment at the plant or during maintenance and repair operations in the field, the zinc alloys frequently provide better or equal performance at lower cost. The ZA Alloys The ZA alloys are a family of three high-performance zinc-aluminum alloys that compete in cost and performance with cast iron aluminum and bronze. The growing number and uses testifies to the versatility of these alloys and is encouraging their consideration in a wider range of applications. The ZA alloys are referred to as ZA-8, ZA-12, and ZA-27, the numbers corresponding approximately to the percentage of aluminum each alloy contains. ZA-8 is a permanent-mold casting alloy and is usually selected for decorative purposes; ZA-12 provides both performance and cosmetic benefits; ZA-27 offers the greatest functional strength. The term high performance ZA alloys distinguishes them and their improved engineering properties from traditional zinc die casting alloys. Maintenance Savings At its mine in Timmins, Ontario, Kidd Creek Mines Ltd. operates over 40 Joy VCR- 150 crawler-mounted air-powered rock drills. Most of the drill components undergo severe stress as the drill batters through the under-ground rock. As the components wear, the drill bits wobble; when the wobble becomes excessive, the drills are rebuilt. In the gear train, which rotates the drill steel, there are three planetary gears with - historically - bronze bushings. Since the planetary gear bushings are wear items, they are routinely replaced during overhaul. The bronze planetary gear bushings (three bushings per assembly) were replaced up to five times annually. With 43 drills in use, bushing consumption approached 600 per year. At the manufacturer's replacement part cost, the 600 bushings and gears would cost more than $20,000 a year. Even though a major saving was achieved by having the bronze bushings manufactured locally, the 600-unit annual usage provided ample incentive to investigate other ways of lengthening drill life and reducing the part costs. One approach was to consider using a bushing material that offered good bearing properties, but was lower in cost. About three years ago, ZA-12 zinc-aluminum casting alloy, costing less than half as much as bronze, was evaluated and selected for testing. One hundred ZA bushings were manufactured and placed in service as the drills came in for rebuilding. At the next rebuild the "drill doctor" (drill maintenance mechanic) noticed that, although the bronze bushings were completely destroyed, on occasion the zinc alloy bushings were not. In addition, he noted that some of the ZA bushings showed less wear than the bronze bushings. Because the bushings were changed routinely during each overhaul, the actual operating life of each bushing was not determinable. Therefore, it was not possible to statistically compare the life of the ZA bushing against the bronze. However, the desired life of the part was from overhaul to overhaul. So the ZA alloy obviously met the objective, giving equal or better life than bronze at a significantly lower price. Based on the favorable results of the testing under actual operating conditions, Kidd Creek maintenance personnel decided to switch permanently to the ZA bushings for rebuilding the VCR-150 rock drills. Original Equipment Application As one of the leading companies marketing the ZA alloys, as well as a zinc -copper-silver mining company, Kidd Creek is interested in developing applications for the alloys by original equipment manufacturers such as joy Manufacturing. Kidd Creek marketing representatives provided joy with information on the Timmins mine tests, along with ZA-12 bushings for evaluation and testing. Based on this information, joy installed ZA bushings in 12 new VCR-150 units and delivered them to customers for use in such areas as granite quarries and copper, lead, zinc, and limestone mines. During the following year, joy engineers closely monitored repair reports to verify the performance of the ZA part. The engineers' findings convinced them of the advantages of ZA-12. As a result, joy now uses ZA-12 bushings in the manufacture of its VCR-150 air tools. Advantages for Casters and Users In the foundry, the new alloys have proved their castability and profit potential in sand and metal permanent-mold processes, as well as the new graphite permanent-mold gravity casting process. The energysaving, pollution-free and ease-of-machining benefits they offer are important to all of these processes. Most recently, the high-performance alloys entered the arena of cold-chamber die casting, where they provide properties beyond those of

Jan 7, 1983

By F. S. Boericke

"INTRODUCTION The mineral found in natural-chromite deposits is never pure Fe0.Cr203, but rather one in which the Fe0 and Cr203 are in part replaced by Mg0 and A1203, respectively. The purest gravity concentrates from many domestic de¬posits consist of a mineral referred to as ""picotite,"" in which this isomorphous replacement is such that the ratio of chromium to iron is low. The Bureau of Nines has investigated methods of chemically beneficiating ores that contain too much iron to be classed as ""high-grade"" chromite 3/ Early investigations 4/ demonstrated that high-iron chromite or picotite ores can be roasted with carbon to obtain selective reduction of the contained iron, and that most of this reduced iron can be removed by acid-leaching the roast products to produce residues of higher chromium-to-iron ratios. tests 5/ indicated that commercially acceptable reaction rates cannot be obtained at roasting temperatures below 1,3000 C., using solid carbon as reducing agent. By this high-temperature reduction and subse¬quent acid-leaching, however, all ores investigated, regardless of the original composition, readily yielded residues considerably better than the minimum specifications for high-grade chromite.In an effort to obtain satisfactory reduction of chromite at lower temperatures, liquid and gaseous seducing agents were tested with varying success. Of the several reducing agents used, methane appeared to be the most promising and was shown to be highly effective at temperatures between 1,000º and 1,100º C., roughly 300º below the roasting temperatures necessary in solid carbon reduction. Further experiments indicated that mixtures of methate with some diluent (hydrogen or other nonoxidizing gas) gave better reduction than did methane alone."

Feb 1, 1946

By G J. Lyman

In sampling a process stream, conventional sampling theory deals only with the variation of the analyte content and neglects the impact of the variation in the mass flow on the sampling variance, whether the sampling regime is time-based or mass-based. This is an obvious simplification of the real state of affairs and it is worthwhile to study this impact via simulation.With a facility to simulate large (long) random functions having some thousands of points in the function and the ability to impose covariance functions on the mass flow and analyte variations, such a study is possible. It is also possible to evaluate the impact of correlation between analyte content and mass flows.This paper describes a limited study of the variance increase due to mass flow fluctuations over the usual sampling variance due to analyte variation during the sampling period. The bias in the sampling result is determined for specific modes of correlation. Simulation methods are used as they are the only means by which a sampling result can be compared to the true assay for the lot; in the physical circumstances of mineral process analysis, it is never possible to determine the true process stream assay.CITATION:Lyman, G J, 2017. The impact of the weighting error, in Proceedings Eighth World Conference on Sampling and Blending , pp 311–318 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017