Search Documents

By Robert H. Robinson, Levent Ozdemir, Russell J. Miller

The paper summarizes an investigation into the applicability of mechanical excavation to oil shale mining; identifies available machine types that are best suited to various aspects of the mining operation; presents preliminary comments on the configuration of an "IDEAL" oil shale mining machine; and establishes the background information necessary for conceptualizing and evaluating new mining methods using mechanical excavation equipment. Conclusions are also presented as to the best currently available systems, as well as potential future systems.

Jan 1, 1983

Geophysical surveys are currently being carried out over mineral prospects all around the Pacific Rim. Many of these surveys are successful in locating mineralisation in porphyry intrusives, mesothermal environments, and epithermal vein systems. A number of examples of surveys in Indonesia and Papua New Guinea are presented, which show the successful application of various geophysical techniques to the discovery of mineral deposits on the Pacific Rim.

Jan 1, 1999

By S. H. Lorain

This paper briefly describes the principal known commercial and near commercial deposits of gold-bearing gravel end the principal placer mining operations of Idaho County, Idaho. It is one of a series of similar papers on western mining districts. The data used in writing this paper were gathered during the summer of 1937. Information concerning gold-bearing gravels was obtained from prospectors and operators, while operators supplied most of the data on mining operations. No attempt was made actually to test the gravels. The principal object of the examination was to indicate placer areas worthy of further investigation by prospective operators.

Jan 1, 1938

By Sridhar Krishnan

This paper presents the results of a comprehensive pre-production pile testing programme for the US$ 800 million 1400MW Coal-Fired Jimah Power Plant Project in Negeri Sembilan, Malaysia. The testing programme included high-strain dynamic testing and fully instrumented static axial and lateral load testing of driven prestressed concrete piles and bored cast-in-place piles. A highlight of the testing programme was the pioneering use of the Global Strain Extensometer (GloStrExt) Method, a deformation monitoring system that uses advanced pneumatically- or hydraulically-anchored extensometers and a novel analytical technique to monitor loads and displacements down the shaft and at the toe of driven prestressed concrete piles. The experience with the testing programme for the Jimah Project also demonstrates the possibility of achieving notable breakthroughs, not only in the monitoring, evaluation and reporting of pile foundation behaviour dynamics but also in our understanding of the mechanisms that underpin such behaviour. These significant gains are undeniably a direct result of the committed and co-operative relationship among the project owner, design/builder, specialist piling subcontractors, pile suppliers and pile instrumentation and testing specialists.

Jan 1, 2006

By Clark P. Mangelsdorf

The report consists of two parts. In Part I is a state-of the-act study of roof truss technology as of January 1979. Included are a history of the truss concept, a review of analysis techniques, a record of hardware available and equipment used in its installation and numerous examples of user experience. Part II is concerned with a study of the role of friction in the behavior of a roof truss. The appendices include laboratory tests by the author.

Jan 1, 1979

By D. G. Krige

For the purpose of determining confidence limits for ore grade estimates, an extensive simulated database was used, which included 1728 ore blocks with ?actual? grades and the corresponding estimates based on ordinary and simple kriging. The practical results show that conditional unbiasedness is essential and that acceptable confidence limits can then be set using Normal theory for the simulated error distribution based on the logarithms of the ratios of ?actuals?/estimates with a variance related to the kriging variance. The mean of the data used to prepare the variogram and the estimated block grade are to be used properly in this approach. A practical analysis was also done of the actual point and block data from a very large mined out Carbon Leader area. The distributions of the actual grades for two levels of block sizes with different levels of variability were fitted using three models, ie. two three and compound lognormal. The trends of tonnages, grades and relative profits for a range of pay limits, as well as the usual tonnage-grade curves, show a practical insensitivity for the choice between the three lognormal models considered.

Jan 1, 2004

Using a series-model of an automotive short range radar sensor (SRR) and a recently completed experimental radar system, field tests have been performed in a surface mine. It was examined, to what extent low-cost electronically scanning radar sensors can provide useful data for assistance systems on large scale mining machines. Simple sensors are useful for anti-collision safety zones or hopper car automation. The more complex and sophisticated experimental radar system using digital beam-forming can clearly detect and map the contours of trenches and slopes. The overall promising results refer to many more potential applications for electronically scanning radar in surface and underground mining as a reliable alternative to mechanical laser scanners.

Jan 1, 2007

By George D. Dub

The Bureau of Mines, in connection with the investigations of war minerals it conducted, examined the graphite deposits of this country, studied the methods of mining and preparation used, and sought to devise more efficient methods for the preparation of domestic graphite, and to standardize the quality of the product. The graphite investigations covered three general phases, as follows: 1. An examination of the deposits in Alabama and other States, and a survey of the methods of mining and preparation used. In this connection methods of sampling and analysis were noted and experiments made to determine a standard method of sampling and a, rapid but accurate method of analysis. 2. Experimental work on the concentration and refining of domestic crucible graphite to improve the quality of the product and to lessen waste. 3. Experimental work in crucible manufacture to determine the properties of domestic flake and the maximum proportions that might be used without impairing the quality of the crucibles. This work was accompanied by photomicrographic study of crucible structure.

Jan 1, 1920

By William R. Wessels

This report describes a field survey and laboratory investigation into the causes of failure of resiliently clad screen decks applied to coal preparation plants. Blinding of screen deck perforations and delamination of the resilient cladding are studied and mechanisms responsible for these failure modes are hypothesized. A laboratory test program to simulate the mechanisms was begun and abandoned when it became apparent that meaningful test results would require a substantially redirected effort. No meaningful test data was obtained from the laboratory simulation.

Jan 1, 1982

By Xingjian Gao

The mechanical properties of a low carbon low alloy steel in the austenite and _-ferrite regions have been examined by thermal-tensile tests using a Gleeble-1500D system at temperatures in the range 600oC to 1300oC and at a strain rate of 10-3/s; these being the conditions that apply to the unbending operation during the continuous casting of steel. The yield strength and tensile strength of steel decreased with increasing test temperature and the embrittlement zone occurred in the temperature range 800oC to 970oC. In the embrittlement zone, the fracture surfaces and microstructures of the tensile specimens were examined by scanning electron microscope. The results showed that the cause of the embrittlement at 950oC in which the minimum %R of A was around 36% is the second phase particles precipitated along the _ grain boundary during deformation leading to inter-granular brittle fracture.

Jan 1, 2010

By Staff

A major emphasis of the U.S. Bureau of Mines is to perform research on the prevention of fatal accidents at mining operations. The leading cause of fatalities in the underground coal mining industry is groundfalls. This proceedings volume presents several new developments that are helping to prevent fatalities and reduce injuries by groundfalls. The papers focus on the problem from two different perspectives. About half of the papers present information and techniques that can be used to train and motivate miners to protect themselves from groundfalls. The other papers explain how to identify and respond to various geologic conditions that affect the stability of the mine roof. Of the 95 groundfall fatalities that occurred during 1986-90, 75% took place in Kentucky, West Virginia, and Virginia. The rate of groundfall fatalities was much higher at small mines. During 1986-90, the rate of groundfall fatalities at mines employing fewer than 20 people was 4.3 times higher than the rate for larger mines. Because so many groundfall fatalities are occurring at relatively small mines in the southern Appalachian coalfields, many of the papers focus specifically on the needs of this category of mine operations.

Jan 1, 1992

By R. M. Sweetin

Detailed descriptions by operating area of the Kidd copper smelter are presented, together with accounts of complement staffing, training, and preparation activities for smelter start-up in June 1981. Concentrate tonnages smelted in the first twelve months of operation were constrained by the capacity of the furnace off-gas system. However, modifications designed and introduced over that period, plus sustained efforts by operations and maintenance personnel have resulted in stepwise improvements in smelter performance.. Consistent operation at design feed rates has been well demonstrated over the third and fourth smelter campaigns and efforts continue on further improving the continuous smelter on-line times and increasing campaign life. In November 1982., following a seventeen month preproduction period, the Kidd smelter attained full operating status.

Jan 1, 1983

By A. M. Milev

A simulated rockburst was conducted underground at Kopanang Mine, previously called Vaal Reefs No. 9 Shaft. The rockburst was simulated by means of a large blast detonated in solid rock close to a crosscut sidewall. The simulated rockburst involved the design of the seismic source, seismic observations in the near and far field, high-speed video filming, a study of rock mass conditions such as fractures, joints, rock strength etc. Knowledge of the site conditions before and after the simulated rockburst was also gained. Some of the important findings are listed below: ?Two areas of damage were identified on the blasting wall: (i) an area of high-intensity damage in which ground velocities of 3.3 m/s were recorded by an accelerometer, which was subsequently ejected in a block of rock, (ii) an area of low-intensity damage where ground velocities of 1.6 m/s were recorded by an accelerometer which remained on the tunnel wall. ?High-speed filming revealed rock fragments being ejected from the wall at velocities in the range of 0.6 m/s to 2.5 m/s. The measurements were taken in the area of low-intensity damage. As planned, no gas pressure was directly involved in damaging the wall of the tunnel. ?The attenuation of peak particle velocities for the main blast in the near field (6 m to 30 m), as a function of distance R, was found to be proportional to R-1.7. ?The simulated rockburst was recorded as a local magnitude ML= 1.3 by the Klerksdorp regional seismic network. ?Peak particle velocities from nearby blasting, recorded on the tunnel wall after the simulated rockburst, were about six times greater then peak particle velocities recorded from the same source area before the simulated rockburst.

Jan 1, 2001

The Tertiary gold deposits of the Hauraki area are predominantly epithermal vein types containing mineral assemblages of quartz, calcite, pyrite, sphalerite, galena, chalcopyrite, acanthite and native gold (electrum). Sulphosalt, telluride (eg hessite), seleniferous sulphide and selenide minerals are important locally. Studies of wall rock alteration mineralogy, fluid inclusions in gangue minerals, and sulphur isotopes of sulphide minerals indicate that the ore forming fluids had the following parameters: pH, near neutral at depth but acidic near surface; temperature, predominantly 320 - 270¦C for base metal dominated assemblages, 280 - 200¦C for precious metal dominated assemblages and generally below 200¦C for late stage barite; apparent salinity, six to zero equivalent weight per cent NaCl; and CO2 concentration, generally around one mole per cent CO2. There is fluid inclusion evidence for boiling during mineralisation in some deposits. Moderate values off S2 and FO2 are indicated for base metal and mixed base metal û precious metal assemblages of most deposits by the predominance of pyrite + chalcopyrite over other iron-bearing phases; primary bornite is absent, whereas pyrrhotite, hematite and magnetite rarely occur in the veins. The largest gold û silver deposits formed from solutions in which the sulphur species in solution were predominantly reduced. Near surface environments and some deep, predominantly base metal, deposits were formed from solutions with approximately equal concentrations of oxidised and reduced sulphur species.

Jan 1, 1984

By Ray Brainard

Charleston Water System?s Daniel Island Extension Tunnel, initially thought to be the simplest of the four replacement tunnels to design and build, became the most challenging after the discovery of an unexpected 30-ft thick lens of sand in the normally consistent Cooper Marl while sinking a shaft on Daniel Island. This paper will explore the challenges involved with determining the extent of the unforeseen lens of sand, the accelerated boring program, and the redesign of the vertical alignment?keeping the alignment between the sand layer and the bottom of the Cooper River. It will describe how the challenges were overcome, and how the Owner, Engineer, and Contractor were able to team together to achieve the desired results.

By Williams K. C

This paper presents a brief account of the plant which has been developed at Port Pirie to recover, by vacuum distillation, the greater part of the zinc content of desilverized lead. The present plant is an experimental unit, which is run in conjunction with the normal refinery practice, but can be cut out of the circuit. It will shortly be dismantled and duplicate units will be built on the sites chosen for the final plant installation.The unit described here has treated flows of 16 to 37 tons per hour of desilverized lead, to recover 90 to 95 per cent of the zinc contained in it. It is not intended here to detail all aspects of the vacuum dezincing operation, nor the developments which precededthe adoption of this design. The essential features of the present plant will be described and, where these are peculiar to the present experimental location, the intended alteration for the final plant will also be mentioned. OUTLINE OF PLANT AND PROCESSLead issues from the continuous desilverizing kettle at about 350° C. containing about 0·57 per cent Zn. It is conveyed by a tiled launder to the preheater, where it is heated to 580-620° C.Hot lead from the preheater enters the vacuum vessel via a barometric leg. From a reservoir holding about 19 tons of lead it falls by gravity in a thin film exposed to high vacuum (20-50 microns)3 and leaves the vessel via a barometric leg, entering the lead pot. The lead leaves this pot at 540-560° C., containing 0·03 to 0·06 per cent Zn, which is removed, together with residual antimony of 0.02 to 0·06 per cent, by a separate final refining process.

Jan 1, 1956

By J. Brent Hiskey

Thiourea is a reagent capable of complexing gold and silver. With the proper oxidant, thiourea can effectively dissolve metallic gold and silver. A thiourea leaching system possesses potential advantages over conventional cyanidation including acidic solutions instead of alkaline, cationic complexes in contrast to metal-cyanide anoionic complexes, and faster leaching rates with acidic solutions of thiourea. Generally, the rate of metal dissolution in thiourea solution is fastest when ferric ion is employed as an oxidant. Acidic thiourea solutions for certain applications could offer a nontoxic and noncorrosive option for processing gold and silver. This paper provides information regarding the fundamental chemistry of the acidic thiourea system, and reviews the dissolution of both silver and gold in acidic solutions of thiourea. The recovery of gold and silver from acidic thiourea solution is discussed.

Jan 1, 1981

By Bolestaw A. Ktosihski

Preloading of bored pile bases by grouting is an effective way of reducing foundation costs. The bearing performance of a pile may be considerably improved. Various techniques and devices are used. Preloading of a pile base by a special grouting installation is preferred. The grouting device consisting of a U-shaped grouting tube with sleeves and a plastic membrane, separating the tube from the pile concrete, has well proven in Polish practice. The preloading may raise the pile design loads by as much as 30%, and increase their stiffness by 50%, in suitable conditions. The preloading equalizes the deformability of piles in a foundation or a structure. Examples of the base preloading use and load tests of base grouted piles are presented.

Jan 1, 2006

By Youjun Tao

Falcon centrifugal gravity separation tests were conducted to study desulfurization and de-ashing performance with different size fractions of a high-sulfur Chinese -0.5mm fine coal in a dense medium. Performance indicators such as combustible recovery, ash and sulfur rejection, and desulfurization efficiency were used to evaluate the separation efficiency. The results show that for -0.5 mm coal particles, all performance indicators except ash rejection are higher for the Falcon concentrator than for flotation. More specifically, for the +0.125 mm size fraction, Falcon centrifugal separation produced better ash and sulfur rejection performance than froth flotation. However, the Falcon concentrator also showed higher combustible recovery but lower ash and sulfur rejection than froth flotation for the -0.125 mm size fraction.

Aug 1, 2013

Close spatial relationships between the deposits of the Etheridge Goldfield (23 000 kg of bullion) and various regional geological and geophysical features suggest that genesis of the ore deposits was a multi-stage process that started with magmatic and metamorphic stages in the mid-Proterozoic, climaxed with structural and hydrothermal stages in the late Palaeozoic and terminated with an oxidation enrichment stage in the Cainozoic.This hypothesis permits classification of the Georgetown region into areas likely to contain deposits of the Etheridge type and those unlikely to do so; it is concluded that there is little scope for the discovery of extensions of this field.However, the stratigraphic interval between the postulated source rocks of the Etheridge field and stratigraphically higher host rocks of the Croydon field may contain disseminated replacement gold deposits of the Carlin type. The potential host (Pyritic carbonaceous, and locally dolomitic siltstone of the Candlow Formation) is locally faulted and cut by granitoids and the extension of a mineralised, long-standing zone of structural weakness.

Jan 1, 1981