Search Documents

By Thomas Passlick

By means of further developed machines and techniques and with growing experiences in jet grouting, the challenge of this building method becomes more and more complex. To keep the concerning risks as low as possible, the requirements on the quality assurance continuously in­crease. The construction of a 37.0m deep seated slab for the Amsterdam metro station Vijzelgracht in marine clay represents such a complex task. This paper summarises the required measures of quality assurance. In particular a new hydraulic measuring device is introduced with which it was possible to detect the column diameter of 2.6m at a depth of 37.0m during the production process and with a very high accuracy.

Jan 1, 2006

By Edmund J. Cardoza

The paper describes the design, construction and quality control aspects of the installation of a cement-bentonite (CB) cut off wall to impede seepage through a flood control dike. Special emphasis is placed upon the development of a proper specification, distinguishing the CB method from the Soil-Bentonite technique. The importance of the pre-construction laboratory testing program and field quality control procedures is emphasized by the fact that the in-place properties and characteristics of the CB cut off may not be known until after a majority of the work is complete. Sections are included which describe the construction method, the specialty equipment and personnel requirements and the quality control/quality assurance aspects of the project.

Jan 1, 1992

By A. L. Engel

In recent investigations of chloride Volatilization of gold at the Reno Station, it was found that the addition of small amounts of copper and NaCl to the charge brought about improved volatilization of the gold. The investigations described in this report were concerned with the recovery, in an aqueous medium, of fumes from chloride volatilization of gold. It was attempted to discover a suitable aqueous medium that would permit absorption, solution, or precipitation of all the volatilized gold immediately upon contact with the medium. A simple laboratory apparatus was employed to produce fumes by volatilization. To this furnace was attached an absorption train consisting of a series of chambers containing the aqueous medium, through which the fumes were drawn by suction. A satisfactory synthetic ore that contained metallic, gold in a quartz-matrix was made and utilized, enough. gold being present in a' small amount of material to permit an accurate, metallurgical balance of the volatized values' to be obtained in all the experiments.

Jan 1, 1949

By P. J. Watson

The objective of this study was to prioritize the potential risks nuisance and biologically active dusts and fumes present in metal and nonmetal mines. This was accomplished by ranking numerical values derived from a matrix formula calculation that took into account dose, mine population, and sampling size. Data used in these calculations were obtained from the Mine Inspection Data Analysis System (MIDAS). The dusts determined to have the highest risk potential were quartz respirable particulates, mine dust, cristobalite respirable particulates, welding fume components, and nuisance respirable dust. Other dusts and fumes that were not ranked in this study, due to small sampling population, but which show a potential risk, include asbestos, talc, hydrogen cyanide, organic compound dusts, arsenic, metal dusts, and metal and nonmetal fumes.

Jan 1, 1987

Tracer gases are an effective method for assessment of mine ventilation systems, but their dispersion characteristics can differ substantially as ventilation parameters, such as flow path and velocity, vary. This research utilizes Computational Fluid Dynamics (CFD) to model a simplified full scale model mine, details a sensitivity study examining mesh size for an underground coal mine simulation, and examines gas dispersion parameters to determine the optimal model methods for simulation of tracer gases in underground coal mines. These models can be used to determine how a given tracer gas profile might be generated in a mine or areas of a mine that are not accessible, for example, immediately following a mine disaster. Accurate simulation scenarios can allow for the remote determination of the status of the ventilation network, but the sensitivity of the simulation at mine scale must be carefully examined.

Jan 1, 2012

By Martin D. Conyac

A 1984 Bureau of Mines investigation identified ho mineral resources in the Wilderness Study Area (WSA). However, four prospects in the WSA contain anomalous amounts of copper and silver minerals; one had traces of gold. Stratabound copper-silver occurrences appear to be prevalent. Quartz veins in the WSA locally contain trace gold, and one mine adjacent to the area produced some gold in the late 1800's. The WSA is underlain principally by Precambrian and early to middle Paleozoic quartzites, argillites, dolomites and limestones that have been complicated by faulting, generally tilted northeastward, and thrust southeastward over sequences of late Paleozoic sedimentary rocks. The stratabound copper-silver occurrences and gold-quartz veins are in Precambrian and Cambrian rocks in the western part of the WSA, as are similar deposits regionally. Sand and gravel, and limestone are abundant, but plentiful resources of these commodities are nearer established markets. In November 1983 there were 5 small groups of current claims oh the WSA boundary; none are patented claims. Probably less than 35 claims have been located within the WSA, mostly in the northwestern portion; hut over 100 claims have been located outside, near the northwestern boundary. Oil and gas leases nearly surround the boundary and 6 extend up to 1 mile into the study area. There has been no recorded mineral production from within the WSA. From 3 to 5 miles to the west, several lode nines in the Johnnie district have produced several million dollars worth of gold from quartz veins, and some silver and lead from galena-calcite veins. These veins generally trend northeasterly and dip northwesterly and probably do hot extend into the study area.

Jan 1, 1985

By Luis Martín Tejeda

El presente texto señala cómo los parámetros geotécnicos de resistencia y deformabilidad pueden generar mayor confiabilidad en un estudio técnico. En este sentido, la literatura geotécnica indica que los resultados obtenidos a través de métodos numéricos son sensibles a la variación de estos parámetros y que algunas propuestas de cálculo son más satisfactorias. Para ello, se utilizó el criterio de falla de Hoek & Brown en términos de Mohr–Coulomb, donde se presenta un ejemplo aplicativo para mineria superficial, en el cual el factor de seguridad y la probabilidad de ruptura del macizo rocoso son calculados mediante métodos geoestadísticos aplicados a la ingeniería de rocas (FOSM - First Order Second Method y puntos de estimación de Rosenblueth).

Sep 19, 2006

By Taylor R. G

This paper reports a biogeochemical study of the Siberia lode of the Herberton tin field. Soil near the orebody contained high levels of Fe, Cu, Pb, Sn, As, Mld Mn. Polycarpaea spirostylis and Indigofera dominii were associated with these high levels but several other species apparently could not tolerate them. The potential of these species as indicator plants is discussed.

Jan 1, 1975

By R. K. Singhal

Canada is a world class producer and exporter of minerals and mineral products. Today's highly mechanized Canadian open pits use state-of-the-art equipment and support technology. They are taking advantage of larger equipment, including in pit crushing and conveying, truck dispatch systems and electronic management tools. Mine planning is computerized. Environmental issues are dealt with in all phases of planning, and equipment modifications are pursued to keep them functioning in the hostile Canadian north. In 1991, Canada's mineral production (excluding fuels but including coal) totaled $C 16.9 billion, a decline of 13.8% from the 1990 total of $C19.6 billion. It is a major producer of nickel, zinc, asbestos, potash, molybdenum and uranium. Canada is also an important source of copper and iron ore (Fig. 1).

Jan 1, 1995

Our ultimate resources come from the Sun and the Earth System. At this time we face a world crisis in energy, water and soil resources. Global pollution problems are increasing in almost all nations. There is an urgent need to use our vast knowledge with a new wisdom and this requires new integrated teams of experts to provide the best alternatives for the needed new development problems. These teams must include economists, engineers and a broad spectrum of scientists. Today it is possible to produce clean energy, stop soil erosion, clean water and reduce and use wastes of many types.   There is a great need to improve science, natural science, education at all levels. All people must know how our planet works and that fluctuations, some inevitable, some controllable, are inevitable and that we must prepare for them. And it is clear that protecting the environment, eliminating pollution, preserving bio diversity is good economics. Ecology Economy cannot be separated.  

Jan 1, 1995

Two concentrates from Palabora, in South Africa, containing 0.056-0.068% undesirable Cu and 0.8 or 2.2% Ti, were chlorinated with air:chlorine ratios of 10:1, 15:1 and 20:1 at temperatures between 1 200 and 1 329 K. The resulting volatile chlorides were condensed and the solutions analysed for Cu, Fe and Ti. Recovery of Cu was less than 25% at low temperatures and short reaction times, but at 1 258 K almost all Cu was removed from the magnetite at all ratios of chlorine to air. At higher temperatures, the increased carrying over of iron as FeCl3 could be minimised by decreasing the partial pressure of chlorine. No titanium was detected in the volatile products and the percentage of Cu recovered was independent of Ti concentration in the concentrates, though as a function of Cl2 vol%, more Cu was recovered at 1 200 K from the low-Ti than from the high-Ti concentrate. In a fluidised-bed reactor, Cu recovery was 58-90% and iron carry-over less than 10 ppm

Jun 21, 1905

By Shirleny Fontes Santos

Muscovite mica crystals lower than 15 mm diameter are discarded as waste in the mining area of Borborema-Seridó (BRAZIL). The objective of this work was the ore dressing and purification of this waste to be used in the preparation of pearlescent pigment. Muscovite was dry ground using knife mills and an ultrasound treatment. It was possible to achieve 67% of mica with particle size lower than 100 µm. This product was used in the preparation of brilliant pigments based on muscovite flakes covered with rare earth oxides (CeO2, PrO2, Ce0,95Pr0,05O2). The pigments were characterized by X-ray diffraction, thermal analysis and scanning electronic microscopy. The color of the resulting pigments was analyzed using the CIELAB method and it showed the following colors: muscovite-CeO2 ? yellow, muscovite-PrO2? black and muscovite-Ce0,95Pr0,05O2 ? orange. Those results have shown that ?trash mica? is suitable for use in pigment preparation.

Jan 1, 2010

Samples weighing O· 2 g are digested with 2 ml of 72 per cent perchloric acid for 2 hr at 180°C, and then diluted to 10 ml. with water. After settling, an aliquot of clear solution is reduced with ascorbic-citric acid, and then a zinc dithiol solution is added to form a coloured molybdenum complex which is extracted with petroleum spirit for comparison with standards.Concentrations down to 2 p.p.m. may be analysed at rates up to 150 determinations per day.

Jan 1, 1970

By Herbert H. Einstein

The innate variability of natural materials and processes causes uncertainty in the models representing the natural phenomena and uncertainty in estimating the parameters that are used in these models. Reliability analyses, in contrast to the traditional factor of safety approach, are well suited to a rational incorporation of uncertainty in design and exploration decisions. Probabilistic kinetic and kinematic analyses were developed and combined to form reliability analysis methods. With one method the reliability, i.e.) the probability of failure, of an individual 2-plane wedge in a slope can be determined. The other method is aimed at slopes with a single slope parallel set of joints. In each case two approaches were developed, an encompassing one relying on computer codes and a simplified or summary approach relying on charts or pocket calculator computation. A major contribution of these approaches is the treatment of joint persistance. Instead of having to assume a certain persistence, it is now possible to use exploration data on joint geometry and to include the persistence effect rigorously.

Jan 1, 1979

By K. C. Lahiri, H. P. Das, G. G. Sarkar

"The petrographic components of any particular rank of coal often show some distinct physical and chemical characteristics. Therefore, their pro-portionate distribution in a coal greatly influences the technological behaviour of the coal.In any size or gravity separation of a coal, the petrographic constituents become segregated to different degrees in some preferred size or specific gravity range. Therefore, a knowledge of the petrographic nature of the washed and/or screened fractions is often considered essential in selecting the most efficient method for coal preparation and in exploring the proper evenues for its utilization.A graphical method is described in this paper to indicate the mineral-matter content and the petrographic components of the washed fractions of a coal at different ash levels of separation in the form of a new washability diagram. This diagram can be conveniently used to assess or predict the petrographic composition of clean coal or sinks corresponding to any desired ash level in the cleans. With the help of this diagram, it is also possible to locate the yield level of cleans at which maximum enrichment of vitrinites and exinites occurs with the least amount of mineral-matter content."

Jan 1, 1971

By Edward P. Barrett

SPONGE IRON has been defined as the metallic product formed by the reduction (removal of combined oxygen) of iron ore or other iron oxides at temperatures below the fusion point of iron. This product probably derived the name "sponge iron" from its porous nature. When the reduction proceeds at slightly higher temperatures and the particles of metal weld together or finally even melt to yield pellets or balls that lack the porosity and low-density characteristic of sponge iron, the product might more correctly be called "direct iron."

Jan 1, 1954

By Dale Preece

A carefully designed and controlled in-place destruction experiment was performed on a concrete bunker buried in 4.27 m (14 ft.) of soil. The objective was to determine if the explosive charges would collapse the structure in-place without requiring mechanical excavation. Collapse of the buried structure was first attempted by drilling holes in the soil and placing four 13.38 Kg (29.5 lb) Comp B explosive charges at a depth of 2.13 m (6.7 ft.). The configuration of the charges when detonated was 2.13 m (6.7 ft.) off the top of the concrete roof and 3.66 m (12 ft.) apart in a square pattern. Detonation of these charges created a crater ~4.88 m (16 ft.) in diameter and 2.13 m (6.7 ft.) deep, leaving ~2.13 m (6.7 ft.) of soil covering. Very limited spalling occurred on the ceiling of the concrete structure as a result of detonating these four charges. The second attempt to collapse the structure consisted of placing another single 13.38 Kg (29.5 lb) charge, identical to the first four, near the geometrical center of the bunker roof. This charge was detonated in the soil cover 100 to 200 mm (4 to 8 in.) above the reinforced concrete roof, collapsing it. Due to the collapsed roof and remaining soil cover, the structure had been collapsed in place, requiring no further demolition.

Jan 1, 2006

By Luis Castelli, Aldo Bonomelli, Giselle Schifferli, Claudio Zamora

"This paper introduces the operational concept and the description of a multi-site Remote Support Center for knowledge management and long-term process performance improvement.This centralized Support Center provides real-time monitoring of open-platform process automation systems, and on-line access to process data and control applications information for multiple sites.Considering that process automation is a key enabler to business performance improvement, sustaining effective performance benefits over time becomes essential. Unfortunately, changes in manufacturing process dynamics, technology obsolescence and in plant operational practices cause the control strategies to lose their effectiveness over time unless their performance is periodically evaluated, and if required, tuned to the new process conditions.A new concept in process automation is proposed through the addition of a new control loop based on performance analysis methodology which is intended to feedback process and automation operation information to system and process specialists, allowing for continuous manufacturing process improvement and sustainable production benefits through effectual control strategies.A remote support center can play a key role in the delivery of such services, by providing the base platform from which a comprehensive process overview and a centralized knowledge database can be executed and additionally, as an enabler for plant operational practices change.INTRODUCTIONA Benchmark on Automation Level in Copper Concentrators conducted by AMIRA in 2004, reported that the Codelco divisions scored below their peers in several categories.Codelco had thereafter been looking for a new automation concept, and had focused on process automation as a key enabler for process manufacturing and business performance improvement. The final decision was to create a strategic alliance with a world-class automation technology provider.The traditional approach based on isolated automation solutions/projects, showed that the control strategies benefits were decreasing progressively over time, because of the on-going need to adapt the control models to the ever-changing process conditions and different plant operational practices. Another consequence of this traditional approach was the wide variety of technologies and automation systems deployed in the different plant sites, with no common automation standards, and with low opportunities to transfer knowledge or practices."

Jan 1, 2010

Professor Skeats said: I wish at the ,outset to express my appreciation of the h0!-l0ur conferred on me by my election as President of this Institute for the ensuing year. The selection of a geologist for this position by a body of mining engineers andmetallurgists may be taken as an indication of the recognition that the subject is one which may play a useful part in the great metal industry. Among the records of primitive man the finding of implements of bronze and of iron indicated one of the important, advances made in human civilization, and shows that...

Jan 1, 1924

By Jack Kadlecik

This final technical report describes the concept feasibility study, testing, design and development effort which went into. The quick opening enclosure access cover and flame path tolerance checking system. A detailed definition of the explosion-proof multiple start threads is shown for two (2) sized electrical enclosures.

Jan 1, 1972