Search Documents

By John L. Schaller

The Bureau of Mines, U.S. Department of the Interior, has investigated the extraction of alumina from domestic kaolin clay by leaching with boiling 26 wt-pct hydrochloric acid. Acid leaching of crushed calcined kaolin feed yields slurries that are slow settling and difficult to filter because of the presence of fine particles generated in crushing, calcining, and leaching. Laboratory research showed that tumbling and moistening crushed raw kaolin on a pelletizing disk caused the fines to agglomerate on the surfaces of the larger particles, while the sharp edges and corners of the larger particles were rounded off. Minus 16-mesh crushed raw kaolin was misted on a 36-in-diam, 8-in-deep pelletizing disk at rates of 175 to 250 lb/hr, and was calcined in either a rotary or a fluidized-bed calciner; negligible degradation occurred. The physical properties of the misted calcined kaolin were evaluated in the leaching system of the clay-hydrochloric acid miniplant. Only minor attrition occurred during leaching, and the slurry was readily filtered on a continuous belt filter.

Jan 1, 1982

By Andrew B. Cecala, Emily J. Haas, Jay F. Colinet

A sociotechnical system (STS) creates a framework that allows an examination of how social and technical factors affect organizational outcomes within a specific environmental context. STS has been rigorously studied with a primary research focus addressing worker-technology interactions. Although these interactions are important, the social processes and interactions that occur whenever any technical or environmental change is introduced into the system have been undervalued. If social processes are better understood, mining organizations could efficiently prepare and stabilize for such changes. With this goal in mind, we sought to extend STS theory through applying principles of meta-design to analyze the results of two case study interventions. Specifically, we studied the impact of an unregulated dust control technology (the Helmet-CAM) and a regulated dust control technology (the Continuous Personal Dust Monitor) on factors within an STS including employees’ knowledge of, communication about, and use of technology to mitigate respirable dust sources. The results are presented in a way that first, addresses the overarching principles of meta-design STS including organizational participation, flexibility, and communication and second, examines how technology implementation processes differ when the organization is complying with a formal, higher-level requirement. Results show that a prominent focus on the social factors within an STS framework could help reduce unpredictability on the technical side and may improve communication within the system to help reduce adoption time, especially if and when accompanying a new, formal work process.

By Alfred Wild

The Kraftile Co. plant, Fremont, Alameda County, Calif.--the largest producer of glazed, structural wall units west of the Rocky Mountains-- maintains modern processing facilities to evaluate and blend a wide variety of clays from several sources to produce quality products. The report desribes the prospecting, exploration, and test methods used to locate raw material sources and covers processing methods, cost factors, and trends. Also, the geologic and ceramic factors are considered in a general discussion of the economics, potentials, and requirements of clays as raw materials for ceramic tile manufacturing.

Jan 1, 1963

By B. W. Dunning

This paper describes studies conducted by the Bureau of Mines to achieve its goal of developing methods for increased recovery and utilization of valuable constituents in a wide variety of domestic and industrial wastes, In this particular study, 36 units of obsolete electronic equipment from military aircraft were disassembled into their modular components by hand to determine materials distribution. Further modular disassembly into individual parts was used to identify metal composition. After identifying the metals in some of the more difficult to dismantle modules, similar modules were grouped together, shredded, mechanically separated, and using metal composition data from hand separation, classified along with the hand-separated materials. Although this equipment is normally classified as law-value iron-bearing aluminum, data were obtained that indicated the potential for moderately higher value classification. The electronic units were classified as to precious metals, copper, iron, and aluminum contents, and scrap values were estimated.

Jan 1, 1980

By O. K. Mahabadi

The scope of this study is to simulate the behaviour of a layered rock sample under standard laboratory Brazilian Disc test using an innovative combined finite-discrete element method (FEM/DEM) research code. The influence of layering and the direction of loading on the samples behaviour are studied through various layering and loading configurations. A parametric study including the effect of loading rate on the tensile strength of samples has been carried out. This paper demonstrates the suitability of the numerical approach to explicitly model rock deformation and failure.

May 1, 2009

By L. W. Berry

Drill and blast planning is critical to successful mine production, both in timing and in results. However, typical planning, reporting, and information exchange usually involves large quantities of data collated in a discordant set of spreadsheets, databases, and reports. Collecting, analyzing, modeling, and distributing all data necessary for efficient drill and blast operations is time consuming and cumbersome. MineSight Axis Drill and Blast provides an extensible core of functions, seamlessly integrated with other MineSight software tools, to make sense of this information. The benefits of improving the management of drilling and blasting processes are immense and result in improved fragmentation at a lower cost, improved shovel and truck productivity, and enhanced ore processing.

Jan 1, 2011

By Earl Redman

The Juneau Gold Belt portion of the Juneau Mining District has historically had the greatest mining and exploration activity within the district. Between 1880 and 1983, the mines within the Juneau Gold Belt produced 6.7 MM oz gold, 3.1 MM oz silver, and 45 MM lbs lead, which had a total value of about $157,000,000 at the time of production. This report summarizes Bureau of Mines work completed in 1986, the second year of the Juneau Mining District study. Fifty mines, prospects, and occurrences were examined and 638 samples were collected for analysis during 1986. Metallurgical samples were collected from seven deposits and preliminary tests of cyanide amenability have been completed for five of these. The simultaneous discovery by private industry and the Bureau of gold-bearing quartz veins cutting diorite gneiss recently exposed by the retreat of the Herbert Glacier is the most notable result of work during 1986. This location yielded gold values up to 7 oz/st.

Jan 1, 2011

By Zhou Wenbin

In this paper the mechanical properties of high carbon equivalent cast iron for automobile brake discs were analyzed through thermal analysis curves. Experiment results show that the mechanical properties have a strong correlation with thermal analysis curves and an effective way to predict the mechanical properties of high carbon equivalent cast iron was proposed based on the features of thermal analysis curves.

Jan 1, 2010

By Sir Stopford Brunton

Gold was first found in Nova Scotia about 1830-40, but its significance at that time was not appreciated. Probably the first discovery that resulted in any work was made by Lieut. C. !'Estrange, at Mooseland, on the Tangier river, in 1858.1 Since that time gold has been mined with varying success until now, and from 1868 onwards work has never altogether ceased. Gold mining in Nova Scotia is at the moment under a cloud, and the idea generally accepted by most people is that it has failed in the past, and that there is no prospect for it in the future. The actual reasons for the present situation have never been carefully analysed, and it seems a good thing to see what really is the state of the case and whether or not this general idea is worthy of credence. It is the purpose of the present paper to analyse the situation in the light of present knowledge, and to set forth some data which may assist in the future development of the Province.

Jan 1, 1926

By Sanford J. Douglas

This publication describes a study by the Federal Bureau of Mines of devices and methods used for testing and splicing 4,160-volt and 440-volt cables and for providing ground-fault protection for 440-volt circuits, as developed and used by the electrical staff of the Tecumseh coal mine, an open-pit operation at Boonville, Ind. The testing and ground-fault devices described should find ready application in other open-pit mines, and, with suitable modifications for voltages involved, in underground mining. The devices and testing methods are based on sound engineering principles and are time-tested and economically feasible, Four devices are used: A high-voltage tester, and a low-voltage high- current tester, both for testing 4,160-volt cables; a tester for 440-volt cables; and, electronic ground-fault protective device for 440-volt cable circuits. All the cable testers and the grounding device were designed and built at the mine from standard parts. They are inexpensive, dependable, and job tested, An attempt has been made here to describe them in enough detail so that interested persons can assemble duplicate units.

Jan 1, 1960

By M. F. Goudge

LIMESTONE surpasses any other rock or mineral in the number and diversity of its uses and in the quantity consumed fur industrial purposes. Either in the raw state or when calcined to lime it enters directly or indirectly into the manufacture of a great variety of products and its sphere of usefulness is continually expanding. The term "limestone" as here employed includes all varieties from high-calcium limestone, consisting almost entirely of the mineral calcite, to the highly magnesian variety, largely dolomite. Lime is also discussed .because lime is simply calcined limestone and often the material may be used in either the calcined or natural state. Limestone has been of service to man since prehistoric times but only in the last hundred years has it become one of the most important raw materials in industry. In every industrial country it comprises the greater part of the total stone produc-

Jan 1, 1937

By J. J. Demeter

Experiments were conducted in 2- and 4-inch-diameter standpipes to evaluate the effectiveness of standpipes as pressure seals. During the experiments, these standpipes conveyed Alan-Wood magnetite (60 to 230 U.S. standard sieve mesh) by gravity flow from one vessel to another of relatively higher pressure. The information obtained has been helpful in a Federal Bureau of Mines investigation of how to make either synthesis gas or hydrogen by a modified steam-iron process employing a continuous recycling stream of granular iron-iron oxide at temperatures of 600° to 900° C. In this process the mixture of granular material flows by gravity from a reduction vessel at low pressures to an oxidation vessel at higher pressures. Data from the 2- and 4-inch-diameter standpipes indicate that it would be practical to use a standpipe as a pressure seal between the reductor and oxidizer. Investigators found that, by gravity flow, the standpipe could convey the Alan-Wood magnetite against pressure gradients up to 1.07 pounds per square inch per foot of column height.

Jan 1, 1961

By K. E. Stanfield

Oil-yield results are presented for 65 oil-shale sections in Piceance Creek Basin, Colorado, sampled during the period 1957 through 1963. Including previously published data, oil-yield results for 203 sampled sections have now been released by the Bureau of Mines to aid in appraising the shale oil potential of the basin. Oil yields of core samples (135 sets) were regarded as reliable bases for appraising the Mahogany-zone interval, but only 5 sets of cores sampled the deeper, lower-zone oil shales. Drill cuttings (68 sets) sampled the lower-zone oil shales, but their oil yields are principally indicative and should be confirmed by analyses of cores. More complete core sampling of the lower-zone oil shales is needed.

Jan 1, 1967

By Alfred Wild

The Kraftile Co. plant, Fremont, Alameda County, Calif.--the largest producer of glazed, structural wall units west of the Rocky Mountains--maintains modern processing facilities to evaluate and blend a wide variety of clays from several sources to produce quality products. The report desribes the prospecting, exploration, and test methods used to locate raw material sources and covers processing methods, cost factors, and trends. Also, the geologic and ceramic factors are considered in a general discussion of the economics, potentials, and requirements of clays as raw materials for ceramic tile manufacturing.

Jan 1, 1963

By J. Roth

The purpose of the present study is to increase the safety of explosive storage. This was accomplished by: a) review of the histories of recent and past magazine explosions to define causes and trends; b) observation of present-day explosive storage conditions and practices at active mines; c) examination of existing Federal regulations on explosive storage to determine whether they address all conceivable safety problems, whether they contain redundant or obsolete standards, and whether their intent is clearly stated; d) recommendation, for safety improvements and for revision and clarification (if necessity) of governmental regulations. Magazine explosions are rare. A recent increase in magazine explosion frequency must be attributed to a large increase in deliberate (criminal or malicious mischief) explosions. Fires of various origins account for the remaining explosions of the past decade. During 1884-1926 several lightning-generated explosions occurred in non-metal magazines, but none recently. It appears that the contents of a well-constructed, metal magazine are immune to direct lightning strikes, regardless of whether the magazine is grounded or not grounded. Grounding a metal magazine cannot be harmful, but it may well be superfluous. Magazines were observed at 34 widely separated mines and storage problems were discussed with personnel at these mines. In general, storage conditions and practices were found to be satisfactory. Usually, only small quantities of explosives are stored on mine property since most explosives are brought in by suppliers when needed. MSHA and BATF standards on explosive storage appear to cover safety aspects adequately. However, certain revisions are recommended to clarify some of these standards and to reduce inconsistencies in their enforcement.

Jan 1, 1983

By J. A. López-Molina, S. García, V. Castellanos-Pedroza

"Grouting aims to reduce the permeability of rock mass below a predetermined value and has been widely used in rock engineering field for a long time. However, the injection procedure needs several empirical decision makings and it is rather difficult to reliably confirm the achievement of improvement, because the grout penetration process is not sufficiently clarified. This investigation proposes a neuronal method of defining spatial distribution of rock hydraulic properties and a fuzzy scheme for estimating their relation with the grout penetration (consumption, localization and filling material). The intelligent method stands as a tool for helping in harmonizing the sealing activities and the medium conditions. The virtual simulation of grouting strategies embraces geology, hydraulic and rock characteristics and the filling process. Important aspects as different pressure injection levels and fracturing systems can be holistically studied using the intelligent environment, resulting in an advantageous, economic, flexible and interactive tool for planning better this critical activity.INTRODUCTION Grouting is a very common method of sealing rock and repairing concrete structures (Butron et al., 2010) and its use in engineering of dam-foundation and tunneling has been documented as very successful (Yang, 2004). Generally speaking, to achieve the closing purpose, boreholes are drilled into the rock mass and grout is injected (under pre-selected pressure) until the fractures around the borehole are filled. The complete filling of these fractures is possible if they are connected to each other in such a way that the remaining water and air can be displaced outside the designed grouting zone (Houlsby, 1990; Kutzner, 1996). Water testing is necessary for evaluating seepage potential and for determining whether grouting is necessary or practical. Regardless of the main reason for the investigations, design of a program for water testing for grouting should consider the type of structure to be built, the geologic conditions at the site and the level of seepage control desired. As information gathered the report must content the fracture openness, number and connectivity, exploratory drill holes orientations, materials situation and a panorama of rock-mass state (quality)."

Jan 1, 2015

By V. N. Rampton, C. F. Gleeson

"Exploration results over three overburden drilling anomalies defined by the Ontario Geological Survey in 1981 in the Kirkland Lake area, Ontario are presented. The anomalies come from lowland areas where overburden is thickest. By mapping the bedrock and surficial geology, by prospecting, humus sampling and shallow till sampling over the surrounding upland surfaces, one can initially evaluate such overburden drill anomalies without costly reverse circulation drilling. The drilling should follow, if necessary, only after surficial base data has been obtained. Preliminary work on these three properties has defined the presence of at least two styles of gold mineralization. One occurs in silicified zones in intermediate volcanics closely associated with northwesterly trending faults and shear zones. The second occurs in quartz-carbonate alternation zones in volcanics intruded by quartz-feldspar porphyry dykes. IntroductionThe three examples presented in this paper present first-hand information on an approach to the follow up of several geochemical anomalies that were found by the Ontario Geological Survey when they carried out reverse circulation overburden drilling as part of the Kirkland Lake Initiative Program (KLIP) in 1980 (Routledge et al., 1981). The initial approach is relatively simple, systematic, and cost and technically effective. It readies the properties for further exploration, or conversely, it could downgrade the properties as viable gold targets."

Jan 1, 1987

By Higgins RJ

Environmental investigations have been undertaken by Ok Tedi Mining Limited (OTML) since 1981 when the Ok Tedi Environmental Study was commenced. Environmental monit- oring and management programmes were implemented in 1983. The programmes included water quality monitoring, river flow and sediment monitoring, surveillance of aquatic biological communities and a health and nutrition survey of the local people. These original programmes have continued, and additional programmes of work have been developed and revised to reflect changing operations and the need to focus investigations on specific areas and issues of concern. In April 1990, following the establishment by the Government of Papua New Guinea (PNG) of environmental management criteria for the Fly River system, compliance monitoring programs were introduced. Details of the compliance and additional monitoring programmes undertaken by OTML throughout the Ok Tedi and Fly catchments, including programmes of investigation in the Fly River estuary, Gulf of Papua and Torres Strait, are presented.

Jan 1, 1991

By Dana T. Updyke

The objective of this project was to develop technical data and evaluate performance and utility of leaky feeder communications systems currently used in North American underground mines. The desired information was obtained principally through on-site surveys. Altogether, six of the seven mining companies known to be using leafy feeder communications were visited. This report covers the findings of these surveys. In addition, the report provides a brief background summary of mine communications, a technical discussion of leaky feeder systems, and conclusions and recommendations based on the results of the survey.

Jan 1, 1980

By H. Haselhuhn

Filtration of hematite ore slurries can be a bottleneck in some hematite processing plants due to inadequate filtration rates caused by the dispersion of fine particles. Flocculation of fine particles in the slurry decreases the specific cake resistance of the filter cake allowing for increased filtration rates. CO2 sparging of hematite slurry was shown to increase the filtration rate by altering the pH and the surface chemistry of the particles. It was shown that an increase in filtration rate of 278% can be accomplished by lowering the pH from 11 to 6.5 using CO2. This was attributed to increased flocculation of hematite and silica particles in the ore.

Jan 1, 2012