Search Documents

By J. L. Page, A. C. Marlowe

The Research and Development Services of South Africa has begun underground trials with a Robbins 52RE blindhole borer using a cutterhead fitted with high pressure water jets to assist mechanical cutting. The objectives of the work are to reduce cutter costs by increasing cutter life and to increase overall penetration rates. The paper reviews blindhole boring in South Africa and laboratory experiments in rock cutting assisted with high pressure water jets. The borer and its ancillary equipment are described. Initial results of underground boring experiments are presented. The paper concludes with the test programme for the future.

Jan 1, 1985

By C. R. Copeland

Water sprays are a common method used to reduce particulate matter (PM) emissions. Various factors such as wettability, surface area coverage, fine particle engulfment rates, interparticle adhesion forces, suppressant penetration and suppressant longevity have all been suggested as critical factors in achieving effective PM control. However, it has not been established which of these factors are the most important. Experimental work indicated that suppressant penetration is the most critical of these factors. The length of time after application that suppressants were effective was also improved by using hygroscopic reagents that retained moisture to prevent evaporation. Maximizing suppressant penetration and improving suppressant longevity led to an average 86% reduction in PM10 concentrations in laboratory dust tower tests.

Jan 1, 2008

By Mark I. Copeland

The Bureau of Mines investigated the effect of up to 1 wt-pct of copper and silicon on the heat treatment response and hardness, tensile, and impact properties of hot-rolled medium-carbon steels. The steels were prepared by induction melting and fabricated into plates by forging and rolling. The tensile strength of 0.2-wt-pct carbon steels containing 0.3 wt-pct silicon was affected significantly by copper in both the hot-rolled and heat-treated (600° C) conditions, whereas the tensile strength of the 0.3-wt-pct carbon steels was less affected. A 600° C treatment was considered optimum as a post-rolling treatment to strengthen the steels by copper precipitation. Strengthening of 0.2-wt-pct carbon steels by silicon was reduced by increasing copper contents.. Optimum impact strengths occurred at about 0.3 wt-pct silicon in 0.2-wt-pct carbon steels containing 0.6 and 0.8 wt-pct copper. The impact strengths were lowest for 0.2-wt-pct carbon steels containing over 0.8 wt-pct copper and greater than 0.3 wt-pct silicon, especially in the heat-treated condition. Copper and silicon solutes and copper precipitates strengthened the steels. This effect was augmented slightly by strengthening through grain refinement by these solutes.

Jan 1, 1973

The 109th Annual General Meeting of The South African Institute of Mining and Metallurgy was held at The Country Club, Johannesburg, Napier Road, Auckland Park on Wednesday, 16 August 2006. Special General Meeting A Special General Meeting to consider the changes to the Constitution was held immediately prior to the AGM. 1. Purpose In order for the SAIMM to remain relevant and ensure maximum value to all members, Council propose three changes to the Constitution. 2. Background Three changes to the Constitution were proposed by the Council on 21 July 2006. These changes now have to be approved by means of a ballot at a Special General Meeting. These three proposed changes are discussed briefly below:

Jan 1, 2006

By Theo Lehner

Turning matte into anodes continues to be an area to watch: for visitors to see pyrometallurgy in action; for metallurgists to keep up with modern smelting furnaces and ever increasing production rates; for management to remain profitable using more tools than taught in school; and for environmentalists to detect the last small clouds from the ever cleaner smelter. Current converting practices have been screened and analyzed, and today, converting and casting is a modern industry. An impressive, though typical learning curve of converter productivity may be detected. Local conditions such as availability and type of raw materials, products extracted, cost factors, etc., have stimulated the development of add-ons or even alternatives to the still dominant method of converting by Peirce-Smith technology. Turning blister copper into anodes follows a similar path, namely increased productivity and improved quality. We dare to predict that development will continue.

Jan 1, 2005

By Orlando Martino

This regional report covers the mineral industries of Canada and 40 countries and territories in Latin America and the Caribbean Basin. Also included is a brief description of the mineral potential of Antarctica. The Latin American region encompasses an area twice that of the United States. Latin America and Canada have a rich and diversified endowment of mineral fuels, metals, and industrial minerals. Tables 1 and 2 provide a summary view of Latin America and Canada's output of its major mineral commodities in world mineral supply in 1991 (revised) and 1992. Table 3 shows the relative importance of a selected group of minerals produced in Latin America in the world mineral economy.

Jan 1, 1994

By Rose L. Ballard

This chapter summarizes data on crude nonfuel mineral production for the United States, its island possessions, and the Commonwealth of Puerto Rico. Included also are the tables that show the principal nonfuel mineral commodities exported from and imported into the United States and that compare world and U.S. mineral production. The detailed data from which these tables were derived are contained in the individual commodity chapters of volume I and in the State chapters of volume II of this edition of the Minerals Yearbook. Although crude mineral production may be measured at any of several stages of extraction and processing, the stage bf measurement used in this chapter is what is normally termed "mine output." It usually refers to minerals or ores in the form in which they are first extracted from the ground, but customarily includes the output from auxiliary processing at or near the mines.

Jan 1, 1983

By H. McSorley

"I note that many of you are involved in the production of zinc, lead and copper concentrates and metal, which I am the most familiar with among the non-ferrous metals. This afternoon, I will describe briefly the responsibilities of a commercial manager within a mining/metallurgical company, the basic framework of a non-ferrous metals concentrate agreement and lastly, a brief discussion of the copper, zinc and lead concentrate and metal markets.I hope this talk will contribute to a better understanding of the business between all of us and look forward to a discussion after the presentation.First of all, I work for Noranda Sales, which is the marketing and sales agent for Noranda Minerals' three operating units: Noranda Copper, Noranda Zinc and Mining Corporation. In addition, Noranda Sales acts for other mining companies in the marketing of their raw materials and metals. Noranda Sales is responsible for procuring all raw materials for Noranda's metallurgical plants, such as the Copper Group's Forne and Gaspe smelters, as well as the sale of surplus concentrates and by-products and metal products. In addition, Noranda Sales trades metals and concentrates and owns a metal brokerage business, Rudolf Wolff, a founding member of the London Metal Exchange. It does $3 billion of business in 60 countries, exporting some 80% of Noranda Minerals' output to the world.What are the responsibilities of commercial management in resource marketing to the mine and metal producers?Resource marketing and commercial administration involves assistance in establishing exploration priorities, contributing to feasibility studies, pre-production planning, product promotion and realization of income for many properties and metallurgical plants through completion of supply and sale agreements with other companie"

Jan 1, 1988

By J. H. Morris, G. M. Steed

Paper presented at Mineralisation in the Caledonides, the Mike Gallagher memorial meeting held in Edinburgh, 27-28 June 1996. Oxygen isotope analysis indicates that quartz, carbonates and muscovite could all have formed in near-isotopic equilibrium with the mildly saline H2O-CO2 ore fluid at 330 degrees C. Calculated values for O, C and S in the ore fluids imply derivation from a deep, homogeneous source region and are consistent with formation either as a direct or an indirect result of igneous processes. Values for delta-O18 plot a little outside the accepted magmatic range, but have almost certainly been modified by exchange reactions with wall rocks. These reactions were also the most likely cause of deposition of the ore constituents. The chemical and isotopic character of the fluid was similar to that in many Archaean and later mesothermal auriferous vein systems, especially the Mother Lode region of California. If the Southern Uplands-Longford Down accretionary complex conceals an Ordovician arc, the tectonic setting was also broadly comparable

Jun 19, 1905

By Roberto Chambi

"El presente trabajo señala la expansión de la producción de la mina Condestable a través de las innovaciones tecnológicas en clasificación de molienda como: la utilización de estas zarandas derrick de cinco pisos cada uno, donde se aumenta la capacidad de cada molino instalado en planta en un 17% en promedio, así como el grado concentrado supera el promedio de 26.35%."

Sep 9, 2007

By Giovanni A. Bonita

The United States Capitol Visitor Center (USCVC) is one of the largest underground structures ever constructed in the Washington, DC, metropolitan area. The 600,000 ft2 (55,750 m2) structure is entirely underground and immediately adjacent to the shallow foundations of the existing U.S. Capitol building. Interior building columns for the USCVC were supported on 186 drilled shafts that varied in diameter from 4 to 9 ft (1.2 to 2.9 m) and in length from 15 to 45 ft (4.6 to 13.7 m). The vast majority of the building utilities were located beneath the basement floor slab. It was decided at the onset of the project to proceed with construction prior to completion of the design drawings, and coordination between the underslab utilities and the drilled shafts had not yet been finalized at the onset of drilled shaft installation. Given depth and location restrictions of the outlets, relocation of the bulk of the utilities was not possible. Almost half of the drilled shafts were affected, leaving redesign as the most feasible remedial solution. The redesign involved adjustments to the shaft length, diameter, and bell. It took place on a case-by-case basis, sometimes only minutes before installation began. Coordination between the field and design team was excellent, and delay associated with the redesign efforts was minimal. In addition, the detailed, high-quality field records kept by both the contractor and field engineers allowed for accurate and fair estimations of the added drilled footage and concrete volumes placed. The additional service fee, which was minimal, was settled quick and fair.

Jan 1, 2006

By J. E. Forciea, O. E. Palasvirta, L. G. Hendrickson

AH pilot and commercial plants working with Mesabi Range taconite employ wet magnetic separation. Progress is being made with a dry magnetic process, but this has not yet been applied to taconite except in the laboratory and pilot plants. Flowsheets in all five plants are similar, including multiple stages of grinding, each followed by magnetic separation, which rejects a finished tailing. The flowsheet in Fig. 1 is used in the preliminary and commercial plants of the Erie and Reserve mining companies and in Unit C of Oliver's Pilotac plant. At Erie the desliming operation is omitted. In the Reserve plants two ball mills are used with each rod mill. Pilotac uses flowsheet 2 in Unit A-B and has also tested flowsheet 3. Principal differences in the three flowsheets are the number of grinding stages and the type of roughing. The terms open-circuit roughing and closed-circuit roughing are best defined by the diagrams. Special Test Data Given in Table I: For the Erie and Reserve commercial plants, Table I reflects routine conditions. Pilotac, the experimental plant, has been run with several flowsheets, including those followed at Erie and Reserve's commercial operations. Pilotac data for these last two flowsheets are similar to commercial plant results and are not repeated in Table I; statistics are given, however, for special test conditions. using other flowsheets. when the objective was to 'to extra-grade concentrate, Variations Among Taconites: Although crude ore tributary to these plants is generally classified as taconite, there are important differences in mineralogy and fineness of dissemination.

Jan 1, 1959

By T. J. Nelson

Natural aggregates, primarily stone, sand and gravel, are recovered from widespread, naturally occurring mineral deposits and processed for use primarily in the construction industry. They are mined, crushed, sorted by size, and sold loose or in concrete products to build roads, houses, buildings and other structures. Smaller quantities are used in agriculture, cement manufacture, and chemical and metallurgical processes. The growth of cities, their buildings and the highways that connect them have created demand for enormous quantities of aggregates. Consumption has now reached 9 t (10 st) per person and continues to grow faster than population. The aggregates industry is the largest mining industry in the United States in terms of production by weight, by volume and by number of active operations. About 80 percent of the concrete pavement and more than 90 percent of the asphalt pavement is composed of aggregates.

Jan 1, 2006

By John A. Johnson

The purpose of this report is to clarify the interpretation of some phases of previous progress reports5/ on the use or omission of stemming that have been brought to the attention of the authors by readers. As the stemming problem was approached from an entirely disinterested viewpoint and the data were presented impartially, results of investigations published in previous reports5/ were obtained under a definite set of conditions and procedure, and they may of may not be duplicated under different conditions and procedure in actual mining practice. Final conclusions regarding the use or omission of stemming in blasting have not been reached pending completion of all aspects of this investigation.

Jan 1, 1942

By B. J. Breen, C. S. Mogg

Considerable borehole investigation work has been completed at a proposed site at Sellafield in Cumbria, supplemented by seismic surveys, other geophysical sensing and geological mapping. The focussing of investigation on the rock mass itself will be achieved by means of the planned underground rock characterisation facility, giving access to depths of about 800 m in the strong, low-permeability basement rocks of the Borrowdale Volcanic Group. Characterisation work undertaken during the sinking phase and interaction with continuing surface-based exploration and monitoring should permit a firmer assessment of the long-term safety of a repository. Key considerations in the choice of a design for the repository include the waste handling method, underground inlet cell, underground vaults, vault environment and environmental effects

Aug 1, 1994

By B. M. England, M. V. Swain, N. Bristow, R. D. Dukino

The toughness and fracture mechanisms of ores with significantly different microstructures from Yandi, Koolan and Mount Whaleback were studied with a view to understanding their degradation behaviour. Bulk fracture toughness was determined by the 3-point single-edge notch beam test and the results interpreted using Weibull statistical analysis; indentation fracture mechanics was also used to measure fracture toughness of the different mineral forms and to understand their response to contact fracture

Apr 1, 1995

By John A. Johnson

The purpose of this report is to clarify the interpretation of some phases of previous progress reports5/ on the use or omission of stemming that have been brought to the attention of the authors by readers. As the stemming problem was approached from an entirely disinterested viewpoint and the data were presented impartially, results of investigations published in previous reports5/ were obtained under a definite set of conditions and procedure, and they may of may not be duplicated under different conditions and procedure in actual mining practice. Final conclusions regarding the use or omission of stemming in blasting have not been reached pending completion of all aspects of this investigation.

Jan 1, 1942

By D. Brand

"The risk management objective of the AMIRA Code of Practice for Metal Accounting has seldom been systematically investigated in the literature up to the authors’ knowledge. Risk is defined in the Australian Standard on Risk Management (AS/NZS 4360:2004), as “the chance of something happening that will have an impact on objectives”. The simplified economic analysis performed in this paper has lead to define “something happening” as measurement non-representativity and “impact on objectives” as NSR loss from the optimal NSR. This has pinpointed a missing link being the establishment of a relation between NSR in flotation plants and measurement representativity. The proposed framework, referred to as the total cost of representativity, answers the previously unanswered question of how much accuracy/reproducibility is fit for purpose in a given flotation plant. Authors readily acknowledge that it is way easier to assess the cost of accuracy/reproducibility than the cost of inaccuracy/irreproducibility. However, this exercise not only answers previously unanswered questions but also establishes an essential link with operational excellence. This paper exposes why such operational excellence could neither be attained nor proved without a state of the art metal accounting system. This should impact not only how metal accounting systems are audited/designed/refactored, but also how flotation plants are designed.IntroductionBecause representative metal accounting is a vital source of information for the financial accounts of a mining/metallurgical company, the need for a code on metal accounting was recognized in 2001 and a team was formed in 2003, under the sponsorship of several major mining houses, to produce such a code. Table 1 exposes the two main objectives of this AMIRA Code of Practice for Metal Accounting."

Jan 1, 2017

By J. Nakayama

For drilling large diameter holes for deep foundations, the common and distressing difficulty of long standing has been in coping with ground containing rocky formations and boulders. Where geological formation contains weathered rock or boulders, or deep rock socket is specified, drilling equipment occasionally is found to be unable to drill through and therefore will need supplementary equipment and procedures. Incentive of the MACH Drill Development has been to realize a capable drilling system for rocks of weathered to fresh rock without losing its applicability to usual overburden. Through seven decades' experience of manufacturing and operation of boring machines, the best features of all sorts of drillhead are known such as the drag bit, wing bit, auger bit, diamond bit, rock roller bit, down-the-hole hammer bit, etc.

Jan 1, 1988

By Sir Robert Hadfield

SINCE the writer has been intimately connected with the development of manganese steel for many years, some remarks upon the early work with regard to the rolling and forging of this material might he of interest, and particularly as to the question of rails of special quality and of superior wearing qualities. In a paper on Iron Alloys, with Special Deference to Manganese Steel, read before this Institute at the International Engineering Congress in Chicago in 1893,1 the writer mentioned that, about 20 years ago, his firm in Sheffield produced railroad material, such as tires and axles, of forged and rolled manganese steel, thus showing that this product could be manipulated and worked up into the various required forms. The tires illustrated in the paper referred to above formed a particularly difficult class of work to produce in a special steel, but no special obstacles were met with Although there was no difficulty at that time in making and producing manganese steel in various forms, forged, rolled or pressed; nevertheless, on account of its higher expense, sufficient encouragement

Jan 2, 1914