Search Documents

By Lewis Martin

Spokane Research Center personnel are currently conducting research on cable bolts to assess their material and support properties, to provide design criteria for roof control systems under various types of underground mining conditions, and to provide background data for computer models of cable bolt supports. Laboratory studies of cable bolts made of conventional steel cables with Garford bulbs and collars resulted in recommendations on characteristics such as embedment length, hole diameter, cable bolt diameter, and configuration of cables. A completed series of laboratory tests has determined the minimum embedment length of resin required for resin-grouted, cable bolt ground support.

Jan 1, 1996

By Shamsher Prakash

Equivalent spring constants for analysis of footings is a function of Young's modulus of pile material (Ep), shear modulus of soil (Gs), and geometry of the footing and/or piles. Shear modulus is strongly strain dependent in soils. Therefore, the spring constants are strain dependent, which is acceptable to the Geotechnical engineers. However, structural engineers prefer to use spring constants as a function of displacement, rather than strain. In order to develop these relationships, appropriate relationships between strain and displacement are needed. Also, modulus degradation with strain needs be built into these relationships. Description of spring constants kx , ky, and kz in x, y, and z direction and k?, k?, k?, about x, y, and z directions are relatively simple. However, description of kxø and ky?, the cross-coupling spring constants depend on 2 - components of displacement and rotation. Thus, there are 8 spring constants and likewise there are 8 damping constants. Approximate strain-displacement relationships on which displacement dependant k's and c's are based are presented with appropriate equations, and a numerical example is included illustrating k's and c's as functions of displacement.

Jan 1, 2002

The Bureau of Mines studied blast-produced ground vibration from surface mining to assess its damage and annoyance potential, and to determine safe levels and appropriate measurement techniques. Direct measurements were made of ground-vibration-produced structure responses and damage in 76 homes for 219 production blasts. These results were combined with damage data from nine other blasting studies, including the three analyzed previously for Bureau of Mines Bulletin 656. Save levels of ground vibration from blasting range from 0.5 to 2.0 in/sec peak particle velocity for residential-type structures. The damage threshold values are functions of the frequencies of the vibration transmitted into the residences and the types of construction. Particularly serious are the low-frequency vibrations that exist in soft foundation materials and/or result from long blast-to-residence distances. These vibrations produce not only structure resonances (4 to 12 Hz for whole structures and 10 to 25 Hz for mid walls) but also excessive levels of displacement and strain. Threshold damage was defined as the occurrence of cosmetic damage; that is, the most superficial interior cracking of the type that develops in all homes independent of blasting. Homes with plastered interior walls are more susceptible to blast-produced cracking then modern gypsum wallboard; the latter are adequately protected by a minimum particle velocity of approximately 0.75 in/ sec for frequencies below 40 Hz. Structure response amplification factors were measured; typical values were 1.5 for structures as a whole (racking) and 4 for midwalls, at their respective resonance frequencies. For blast vibrations above 40 Hz, all amplification factors for frame residential structures were less than unity. The human response and annoyance problem from ground vibration is aggravated by wall rattling, secondary noises, and the presence of airblast. Approximately 5 to 10 pct of the neighbors will judge peak particle velocity levels of 0.5 to 0.75 in/sec as "less than acceptable" (i.e., unacceptable) based on direct reactions to the vibration. Even lower levels cause psychological response problems, and thus social, economic, and public relations factors become critical for continued blasting.

Jan 1, 1980

By Clyde DeRossett

Surface fractures, sometimes of significant size, are observed in eastern Kentucky over high extraction areas. Field observations were correlated with mine maps and a regional subsidence prediction computer model. The opening of large fractures is attributed to the presence of a pre-mining joint system, which exists near outcrop in the eroded Appalachian plateau. Lithological composition of the overburden influences the process of fracture opening. No correlation was found between the areas of the predicted maximum horizontal extensions and the actual location of fractures. In this paper a mechanism of fracture formation as a result of the high extraction mining is presented, with recommendations for mine planning to minimize surface damage.

Jan 1, 1993

By R. D. Berkenkotter

Titanium and iron assays obtained from cores of three diamond-drill holes from the Cebolla Creek titaniferous iron deposit were evaluated by statistical techniques to obtain information concerning the mineral characteristics of the deposit and to make a preliminary determination of sampling requirements for the deposit. A range of sample volumes representing sizes from one-sixth NX core 2 feet in length through full NX core 10 feet in length were prepared by split-ting the NX core with a diamond saw and combining pulverized splits. Results indicate the existence of at least two statistical populations having different average grades of iron and titanium. Each has an assay frequency distribution that is not normal but is highly peaked (leptokurtic). Frequency distributions of assays from specific altered zones of the drill holes appear to be normally distributed. Increasing the cross-sectional area of the sample unit to change assay volume did not result in significant changes either in assay values or the resulting frequency distributions of assays. However, when assay volume is increased by increasing sample interval, the shape of the assay frequency distribution changes, and a normal distribution of assays is approached. Positive correlation exists between titanium and iron assays. The degree of correlation, although very significant, is too low to use for prediction purposes. Although the amount of data from three widely separated drill holes is not sufficient to establish an average grade for this large deposit, it indicates a range of expected assay values and provides some information for determining requirements of future sampling for evaluation purposes.

Jan 1, 1963

By F. Habashi

Asbestos, an extremely useful natural resource, has been studied extensively mineralogically and for industrial application. Its extraction from ores has been greatly improved with respect to safety in the work place. In spite of that, there is a decisive effort in many countries to ban its use on the grounds that it is a toxic substance. This action resulting in drastic decrease in production and the possibility of destroying the industry. The chelation of asbestos with organic dyes seems to be a promising way to abate its toxicity. Dyeing can be done when the fibers are slurred in water at ambient conditions in the same way as textile fibers.

Jan 1, 2009

By E. Bongajum

We present results from petrophysical studies to characterize a Zn-Pb-Ag deposit in Nash Creek, New Brunswick. The measurements are part of an integrated study that includes geological and geophysical data acquired on the property. In order to successfully characterize the ore body, an understanding of the relevant physical parameters and their change with vertical and lateral variations of the target lithology is necessary. The quality of the estimated 3D variation in the physical properties is supported by the presence of several boreholes that randomly span the survey region. Density was measured from cores of thirty-two boreholes across the area. Seventeen of these boreholes constitute two intersecting borehole profiles, which is ideal for locally modeling the 3D distribution of the ore deposit. High densities (>3.2g/cm3) correlate strongly with Zn-rich mineralization zones (low resistivity). Compression and shear wave velocity measurements made from representative core samples of the regional geology range from ~2.91 to ~6.41 km/s for P-waves and from ~1.41 to ~4.20 km/s for S-waves. The lower bounds of these velocity values correspond to regions with a high degree of alteration. Moreover, porosity estimates from rocks on the property suggest that porosities range from 0.35% to 11.79%. Induced polarization (IP) measurements confirm that mineralized samples show a significant chargeability and resistivity contrast with respect to the host rock. Thus, chargeability and resistivity information can be combined to adequately identify conductors associated with mineralization in electrical survey data. Information on these physical parameters and their 3D statistical distribution have serious implications on various aspects of mineral exploration that include: resource estimation, choice of geophysical data acquisition and interpretation, and information for preliminary rock stability assessment.

May 1, 2009

By H. T. Kennedy, J. E. Little

An empirical equation for the prediction of the viscosity of several pure paraffin hydrocarbons and nitrogen is presented. It involves temperature, pressure and six constants of the material, and it applies reliably to both liquids and gases. The equation is similar in form to van der Waal's equation of state. For the paraffin hydrocarbons methane through r-hexane and nitrogen, an average absolute deviation of 1.9 percent was obtained on 1,006 data points described in the literature by 14 authors. When this equation is extended to complex, liquid hydrocarbon mixtures, a correlation was obtained with an average absolute deviation of 9.9 percent. INTRODUCTION Equations describing the flow of gas and liquid through porous media contain the viscosity coefficient of the fluid. If other pertinent variables remain constant, the volume rate of flow is inversely proportional to this coefficient. In dealing with condensate fluids and volatile oils, however, the compositional effects resulting from changing pressure materially affect the viscosity. The effect of compositional changes also may be significant in certain secondary recovery or pressure maintenance processes, notably miscible displacement or gas injection. Early attempts to describe the performance of reservoirs utilized a volumetric material balance method wherein gas and liquid in the reservoir were identified as produced gas and liquid at the surface. This method of analysis proved adequate for reservoirs at moderate temperature and pressure that contained gas with moderately low amounts of condensable materials. The volumetric material balance procedures for "black oil" reservoirs leave much to be desired when applied to condensate and volatile oil reservoirs because phase behavior and compositional changes are relatively more important in these cases. The alternative is a compositional material balance, which in turn, requires a correlation of properties of the reservoir fluid with composition. This paper supplies this correlation in regard to viscosity, for reservoir crude oils. REVIEW OF LITERATURE The literature contains many empirical equations describing the effects of composition, temperature and pressure on the viscosities of pure liquids and binary liquid mixtures. However, the applicability of a majority of these equations is limited to very low pressures and to a small number of systems. Most of them, when applied to complex hydrocarbon systems, are of little value. The lack of utility of the majority of equations results from the fact that they were developed to show the separate effect of temperature, pressure or composition on viscosity, but not to predict the viscosity as a function of all three variables. And with the few exceptions noted below, they were developed to apply to much simpler systems than hydrocarbon mixtures. Eakin1 developed an equation for the viscosity of pure light hydrocarbons applicable in the gas, liquid and dense fluid regions, and in its most general form is written as µ - µo =A(ebP - e-cpk) The pure component viscosity at atmospheric pressure and temperature T, µo, was calculated using the Sutherland equation: µo = BT3/2/T + S The constants in Eakin's equation permitted the term e-CPk to become quite small at high densities (above 0.215 gm/cc), and the general equation would simplify to

Jan 1, 1969

By V. M. Shick

With gentle bedding within the zone of support pressure the delamination in roof rocks may occur only on those stratification planes where cohesiveness of rock is close to zero. Unlike this, at dip angles of more than 30-35° disintegration of rock occurs on the surfaces with cohesion up to 5 MPa. Therefore, the delamination in roof rocks at inclined beds is greater than at gently dipping ones. The original disintegration along the pressure fissures with the formation of block structure at inclined strata is not typical, and it may be observed only in roofs with included thick rocks; in this case, the orientation of fractures depends on the angle of seam inclination. Deformation of roof roocks above the mined-out space is determined by anisotropy of layers stiffness (hardness). With the increase of dip angle the own bearing capacity of layers will rise in the direction of strike. It was emphasized that the natural and technological factors are of great importance for rock pressure manifestation in longwalls.

Jan 1, 1996

By Charles Vaught, JON VOLKWEIN, ROBERT PETERS, ERICA HALL

Since 1999, the CWP level among miners with 25 years or more experience, for instance, has risen from slightly more than 4% to 9% (See Figure 1). While it is obviously necessary to protect all miners’ lungs, there is now a technology to improve the chances that new miners’ lungs will be protected from the day they begin work.

By T. Gerritsen, A. Matyas, F. Stober, I. Candy

This paper describes developments in ferro-nickel furnace technology, specifically improvements to cooling methods, furnace controls, and high voltage furnace operating regime. The evolution of these technologies is briefly presented, as context for describing the current state of the art that has enabled ferro-nickel furnace operation at over 75 MW and specific energy consumption of less than 400 kWh/t dry ore. Examples from existing operations are used to illustrate present best practices, and potential future trends are discussed. The paper begins with an overview of the fundamental aspects of pyrometallurgical treatment of lateritic ores that drive ferro-nickel furnace design. Furnace wall cooling methods are related to the requirements resulting from specific furnace process conditions, including slag and metal compositions, as well as arc and bath power. The benefits of high productivity and low specific energy consumption resulting from high voltage (shielded-arc) operating practice are discussed, along with the furnace controls and electrical power train that enable such operation even with captive power generation.

Jan 1, 2004

By J. W. Paul

This report is one of a series of papers on coal mining methods and costs which are being prepared through the sponsorship of the U. S. Bureau of Mines for the purpose of bringing to the industry a knowledge of methods as they are used at the present time, and data on certain features which govern costs, safety, and conservation. The methods employed are, influenced by local conditions with respect to the character and dip of the coal, the nature of the, roof and the thickness of the overburden, and the means employed for roof support and its control.

Jan 1, 1929

High Pressure Grinding Rolls Scale-Up and Experiences

Sep 13, 2010

By Robin J. Batterham

We still need to innovate, but it is getting harder. The real price of metals is declining, return on shareholder value is lower than other industries, and there is a shorter-term focus on staying viable in a capital-intensive industry where timeframes for implementation of new technologies can be long (+I5 years). In this environment, the levels of R&D spent by major minerals companies are remaining steady at around 0.2%-0.5% of revenue. This is not large and to remain viable in the future, we need to be smarter about the way in which we do R&D. The mining industry is a knowledge-based industry. Driving down the cost curve demands innovation, which demands knowledge. To be smarter and more effective in our approach to innovation, a new paradigm is required Generating, capturing and using knowledge has evolved from Mode 1 (discipline based and clear distinction between basic and applied research) to Mode 2 (multidisciplinary, team-based approached with flow between basic and applied activities). Mode 2 is now seen to be much more efficient and to deliver better appropriability (Tegart 2003). To survive, we need to innovate, and the best way to do this is collaboratively. Some examples and pointers for the future will be given in this paper. THE CURRENT SITUATION The Rand report and other recent studies have painted a grim outlook for the mining industry. The real price of metals continues to decline (Figure 1) and profit margins remain thin. This is reflected in shareholder returnwhich are well below other industries (Figure 2)-and current management strategies-which reflect something of a "survival mode." The current focus for most mining companies is on short-term, incremental gains

Jan 1, 2004

By Stuart Brashear, Lee Schettler

The effect of water on several ANFO/emulsion blend ratios are documented by both physical observations and analytical testing to demonstrate the effect even small quantities of water can have on water resistant blends.

Jan 1, 1996

By L. N. Hill

The classifiers on the primary grinding circuit at Cyprus Sierrita have been upgraded from 0.66 m (26 in) diameter hydrocyclones to 0.84 m (33 in) diameter hydrocyclones. This has resulted in a 4.3 % (11 t/h) (12 standard tons/hour) increase in mill throughput while producing a flotation feed which contains 4.8% less +300 micron (48 mesh Tyler screen size) material. This reduction in flotation feed particle size has increased copper (CU) recovery by 0.8 %. Various grinding circuit relationships were evaluated. These relationships include circulating load versus throughput, horizontal versus vertical cyclone configuration, and the effect of cyclone components on performance. We conclude that the improvements achieved are due to a shift in the overflow size distribution created by a cyclone diameter more suited to our operation, and by eliminating the cyclone capacity constraint in the grinding circuit.

Jan 1, 1994

By Joseph M. Singer

This research project had two main objectives: (1) To identify the smoke limits of gaseous fuel-air mixtures and (2) to obtain and evaluate basic chemical information on the formation of smoke in very rich flames near the smoke limit. Such information would do much to establish the circumstances for car-bon deposition in gas appliances and in other types of combustors. Based on tests with ethylene and propane, these studies showed the following: 1. Smoke limits are related to the yellow-tip limits of the fuel. Previous research established sufficient data to permit prediction of yellow-tip limits on gas burners using a wide variety of fuels. The present study of smoke limits deals only with ethylene-air flames, but the concept that was developed is probably applicable to other fuels.

Jan 1, 1962

By Fred N. Kissell

This handbook describes effective methods for the control of methane gas in mines and tunnels. It assumes the reader is familiar with mining. The first chapter covers facts about methane important to mine safety, such as the explosibility of gas mixtures. The second chapter covers methane sampling, which is crucial because many methane explosions have been attributed to sampling deficiencies. Subsequent chapters describe methane control methods for different kinds of mines and mining equipment, primarily for U.S. coal mines. These coal mine chapters include continuous miners and longwalls, including bleeders. Coal seam degasification is covered extensively. Other coal mine chapters deal with methane emission forecasting and predicting the excess gas from troublesome geologic features like faults. Additional coal chapters contain methane controls for shaft sinking and shaft filling, for surface highwall mines, and for coal storage silos. Major coal mine explosion disasters have always involved the combustion of coal dust, originally triggered by methane. Thus, a chapter is included on making coal dust inert so it cannot explode. Methane is surprisingly common in metal and nonmetal mines around the world, as well as in many tunnels as they are excavated. Accordingly, a chapter is included on metal and nonmetal mines and another on tunnels. Proper ventilation plays the major role in keeping mines free of hazardous methane accumulations. The ventilation discussed in this handbook, except for the chapter on bleeder systems, deals only with so-called face ventilation, i.e., ventilation of the immediate working face area, not ventilation of the mine as a whole. The omission of whole-mine ventilation was necessary to keep this handbook to a reasonable size and because a huge amount of excellent information is available on the subject.2

Jan 1, 2006

By Ellsworth R. Spencer

An assessment of U.S. western hardrock miners? noise exposures was conducted as part of a multi-year National Institute for Occupational Safety and Health (NIOSH) survey of noise exposures in each sector of the mining industry. Noise from selected mining equipment and operator noise exposures were measured, analyzed and tabulated for dissemination to the participating sites and are being used to direct NIOSH research and interventions to address the greatest noise hazards. Eighty-two noise dosimeter measurements were obtained, along with time-motion studies as the miners operated hardrock mining machines. Of the operators, 96% had daily noise doses that exceeded the U.S. Mine Safety and Health Administration?s (MSHA) permissible exposure level. The average gold miner dosages while operating the following equipment were: haul trucks - 261%, load-haul-dumps (LHDs) - 235%, single boom drills - 221%, bolters - 214% and dual boom drills - 163%. The worst exposure level was a silver miner with a daily dose of 873%. Time-motion data showed that this miner?s exposure accumulated most rapidly while operating a jackleg drill. These results will be used to help prioritize noise control development by NIOSH and other partners.

Jan 3, 2010

By G Wyartt

Systems such as Davey Bickford’s Daveytronic® SP blast initiation system and electronic detonators have been an integral part of drill and blast activities in Australia for over a decade, with the significant benefits of electronic blasting well documented. Since 2010 the Multiblast feature has been commercially available, which enables eight individual blast patterns (up to 1500 detonators each) to be blasted in the same firing window. Synchroblast has been in active operation since 2012, which allows a blast of up to 4500 detonators – either as a single blast pattern, or several smaller adjacent blast patterns – to be reliably initiated.Multiblast manages blasts separately but concurrently, allowing all blasts to conduct prefiring checks simultaneously from the firing point utilising only one remote blasting unit. Each blast can be selected and fired individually, in a sequence determined by the operator by scrolling through the colour display. Synchroblast automatically detects the blasting configuration, and manages all detonators as a single blast pattern. This simplifies the design and blasting processes for the mining operation.Multiblast and Synchroblast are routinely employed throughout Australia and globally in both open cut and underground operations, enabling optimal productivity due to increased blast volume and reduced operational downtime associated with blasting events.A number of case studies will be presented in this paper, detailing various mining operations that are consistently blasting in excess of 2500 detonators per blasting event as a part of standard drill and blast operations. Blasts over 3000 detonators are becoming more frequent as mine planning departments adapt to this operational capability and flexibility.CITATION:Wyartt, G, 2017. Multi and Synchroblasting – maximising operational productivity, in Proceedings Iron Ore 2017, pp 631–634 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017