Search Documents

By David E. Albus, Bidjan Ghahreman

A single-family home constructed on the side of a slope in Los Angeles, CA, was subjected to lateral forces due to soil slope creep on the pile foundation supporting the home. Impacts to the property included cracking and separations in the street, retaining walls, exterior concrete flatwork, and decorative concrete features in the rear yard area. The home was supported by concrete piles that penetrated the surficial soil mantle and were embedded in underlying bedrock. However, the home exhibited minor distress that suggested even the home was being affected by soil creep. Selected points on the home were monitored with an optical survey method and manometer over a period of two years to assess if the home was undergoing vertical or lateral movement. Monitoring data indicated the home was in fact moving down slope in a manner consistent with slope creep. As a result, the authors were concerned that continued movement due to slope creep could result in over-stressing of the piles that support the home and ultimately lead to failure of the foundation system. An evaluation was then undertaken to evaluate the behavior of the foundation system due to forces from slope creep. Research was performed during the course of evaluating the conditions to consider various approaches to modeling pile behavior of the piles supporting the home. Some research has been performed to field measure creep displacement of soils and rock in slopes. These previous works have found a diverse behavior of the soil displacement with depth (velocity profile) indicating the process is very complex. An example of various velocity profiles measured in field experiments is depicted in Figure 1. Other research focused on theoretical models of velocity profiles and exhibited similarities to some of the field measured cases.

Jan 1, 2018

During the construction of storage caverns, and during their lifetime if the use to which they are put so requires, it is necessary to provide adequate ventilation to ensure the safety and comfort of the underground workforce. An analysis of likely contaminants during construction has indicated that where a large facility is situated in a rock mass of even moderate temperature climatic conditions are likely to be the limiting factor during most of the mining operation and atmospheric pollution when blasting is undertaken. Possible options for improvement are increased air flow, cooling of intake air and reduction of the heat source by altering the number and type of haulage units employed in the cavern. Local solutions are an alternative approach where heat problems are confined to a few specific locations

Aug 1, 1994

By M. M. K. McCrank

"PRACTICAL SAMPLING TECHNIQUESIt is important to achieve reliability when sampling heterogeneous materials where there is a difference in composition, and non random distribution of the constituent particles. Throughout the design, construction and installation of sampling systems it must be borne in mind that the sampling point must be capable of:-allowing each particle in the stream an equal opportunity to be sampled.-accepting and collecting as large a volume or mass of material as necessary to satisfy the requirements of particle counting statistics.-establishing a sampling plan so that the sample is representative of the whole to a defined standard of accuracy.Design ConsiderationsFactors that may influence the design of the sample point include:-the mass, or volume flow rate of the material being sampled-the size and shape of the material or flowing stream-the physical condition of the material being sampled (i.e. temperature, wetness, size consist, density).-the chemical composition of the material being sampled -the location of the sample point and the space available for installation, extraction, reduction where necessary, secondary sampling, and return of the sample rejects downstream.-whether the process to be sampled is in an existing plant or one yet to be designed and built.-ease of access for servicing and maintaining the equipment.-whether the sampled material must be collected continuously or intermittently.-whether an existing sampling method is likely to be adequate or whether a new technique has to be developed."

Jan 1, 1989

By John A. Herbst, Xiangjun Qiu

"Prediction of wear on a microscale level in mineral processing equipment turns out to be a challenging undertaking. This is particularly true for cases in which the objective is to use such predictions for wear parts design. The key to obtaining such predictions has turned out to be the use of physics based models along with phenomenological constitutive equations. In this paper, two components of the HFS tool set, one for particles (DEM) and one for slurry (MPF), are used for modeling. These tools are applied to the simulation of wear of SAG/AG shell lifters/plates and wear in slurry pumps. In each case wear predictions are validated with plant measurements.INTRODUCTIONHigh Fidelity Simulation (HFS) has emerged as an important tool set for mineral processing plant equipment design and optimization (Herbst and Potapov, 2003; Herbst and Nordell, 2002; Herbst and Lichter, 2006). This tool set consists of Discrete Element Modeling (DEM) of particle motion, Multi-Phase Flow (MPF) for liquid motion, discrete grain breakage (DGB) for particle fragmentation and discrete grain liberation (DGL) for mineral liberation (Campbell, Potapov and Tsuji, 1997; Ferzinger and Peric, 1997; Potapov and Campbell, 1996; Herbst and Potapov, 2005).Three sample snapshots of basic HFS illustrating the use of each of the various types of mineral processing equipment are shown below.Figure 1 shows a snapshot of a DEM simulation of ball charge motion in a commercial scale Vertimill. DEM simulation involves simultaneous solution of Newton’s Laws of Motion for 400,000 balls."

Jan 1, 2007

By Linneas Laage, Thomas Weber, William Pomroy

"Underground mine fires can significantly influence mine ventilation airstreams, in some cases throttling or even reversing airflows. As a result, the performance of a metal and nonmetal mine stench fire warning system, which depends on the ventilation to carry the vital warning signal, under fire conditions is different from performance under nonfire conditions. The safety of underground miners can be jeopardized if the warning signal is delayed. This Bureau of Mines report describes research to investigate fire and stench warning system interactions. A computer model is presented that permits quantitative analysis of stench warning signal delays as a function of fire location and intensity. The results of a case study involving computer simulations of stench distribution in a hypothetical mine network subject to various fire exposures are also discussed. This case study illustrates a technique for identifying the areas within a mine that are subject to unacceptable warning signal delays, thereby enabling preemptive action by mine personnel, such as redeployment of stench injectors. INTRODUCTIONFires are an ever-present threat to the safety of underground miners. Since the smoke and toxic gas produced by a mine fire can be spread rapidly by the mine's ventilation system, mine evacuation must be accomplished as quickly as possible in the event of fire. In metal and nonmetal mines, the most common means of passing the fire warning signal to each miner is the stench system. The typical stench system utilizes ethyl mercaptan, a highly odoriferous organic compound, injected on the surface into the compressed and/or ventilation airstreams. Upon smelling the stench, workers evacuate the mine according to an emergency preplan.Although the stench system has been used successfully for over 60 yr, it has several serious shortcomings, owing to certain chemical properties of ethyl mercaptan and to certain performance characteristics and limitations of present injection systems.Recent Bureau research succeeded in upgrading the overall safety and effectiveness of the stench system through the use of a superior stench odorant and the development of improved stench injection equipment (1).4 This research has also investigated a specialized computer simulation model capable of calculating the precise concentration of stench in any mine ventilation network branch at any time after stench release (2). An adaptation of the computer model now enables the analysis of stench system and ventilation system interactions under the influence of a mine fire."

Jan 1, 1987

By Richard Miller

RECENT studies of creep have made it apparent that plastic deforma-tion may occur in metals under stresses less than the elastic limit as deter-mined from short-time tests. In summarizing conclusions drawn from creep tests by various investigators, Tapsell1 said: "It is evident that if a material has a true elastic range, the elastic limit must represent the maximum stress for no creep." The presence of a. definite elastic limit, represented in single crystals by a critical or threshold shearing stress, is claimed by Schmid2, Elam3 and others who have investigated the plastic deformation of single crystals. However, this "law of critical shearing stress" was deter-mined2 from short-time tests, and the measurement of the deformation was made with apparatus primarily designed to observe large amounts of plastic deformation, not to detect elastic changes. Experimental data recently obtained with highly sensitive instru-ments by A. W. Hanson4 on zinc and by Podaschowsky5 on rock salt indicate that the elastic range in single crystals is considerably narrower than formerly was supposed. Moreover, a theoretical possibility of permanent deformation, under the influence of even the smallest shear stress in single crystals above a certain temperature (Td), has been developed by G. I. Taylor6. This evidence seemed to warrant an examination of the elastic limit in large single crystals by means of creep tests. The first metal chosen for examination was zinc.

Jan 1, 1936

By Georgios Kalamaras, Chiaia Dinu, Platania Paolo, Alessio Carlo, Giampiero Cirvegna, Claudio Santucci

The Project alignment initiates north of Pinerolo, along the State Road 23[S.S. 23] that is one of the principal arteries to the northwestern Alps where a number of Olympic events for the 2006 Winter Games will be held. The 3.5 km ring road bypasses the Porte habitat by traversing twice the Chisone River. It consists of the following principal structures [Figure 1]: San Martino bridge [130 m in four bays] Prarostino viaduct [130 m in four bays] Craviale tunnel [1055 m] Turinella bridge [a 50 m long bridge that connects the two tunnels] Turina tunnel [665 m] Malanaggio viaduct [350 m in 9 bays]. The road section is 13 m wide and is made up of two 3.75 m lanes, a hard shoulder [1.50 m wide] and a 1.25 m wide curb for each lane. The Project maximum velocity is 100 km/h.

Jan 1, 2005

By C. McCall, J. T. Knight, J. R. Ridley

Gold mineralisation in the gabbro sills is mainly stratabound to quartz- and Fe-rich, granophyric-textured units and is sited in undeformed, brittle quartz vein sets, which form pipe-like orebodies. Hydrothermal wallrock alteration consists of hornblende-plagioclase-calcite-quartz with minor biotite, garnet and chlorite and with arsenopyrite and pyrrhotite as the dominant sulphides. Geothermobarometric data suggest that gold was deposited at around 520 degrees C at 2.8-3.8 bar. Mineralisation is thought to have occurred during amphibolite-facies metamorphism. Fluid inclusion and isotope data indicate that gold mineralisation was the result of deposition from a low-salinity H2O-CO2-CH4 fluid of either metamorphic or magmatic origin. Although the Three Mile Hill deposit differs from others in the area in its wallrock-alteration assemblages, peak-metamorphic timing of gold deposition and distinct geochemical associations it forms a brittle stratabound ore body which suggests structural and gold-depositional mechanisms in common with those of the other gabbro-hosted gold deposits

Jun 18, 1905

By J. Winterton

Estimating the residual metal inventory of large heap leaching operations is desirable for many reasons. Several methods have been tried with limited success. Drilling data from the Valley Leach Facility at AngloGold Ashanti's Cripple Creek and Victor Gold Mine has been used to develop a robust inventory estimation technique. The technique is presented along with discussion of the particular inventory components and evaluation methodologies.

Feb 27, 2013

By T. Patten

A method for stabilizing mercury containing waste for landfill disposal would be a very cost effective solution for industry. A mercury polythiocarbonate material which is made via a metallurgical process passes a traditional TCLP for mercury. The mercury polythiocarbonate material was subjected to a more thorough evaluation, the Integrated Leaching procedures as described in Kossan (1) and Sanchez (2)The procedure involves leaching the mercury polythiocarbonate material at varying pH and sample size to liquid. The procedure had to be adapted for small sample sizes and finely divided materials due to the product characteristics and available material. The leachates were evaluated and found to be stable within common environmental pH values. The performance details on how Inter-Mountain Labs met the leaching requirements of the procedures and the analysis of mercury are presented.

Jan 1, 2012

The Martha deposit is an economic giant epithermal gold deposit, with mined and unmined resources of more than 218 000 kg (7 Moz) Au. The Au-Ag, base metal sulphide-bearing quartz lodes in the Martha deposit form an extensive braided pattern within hydrothermally altered andesite wall rock. There are five main quartz lodes: 1.      Martha, 2.      Welcome, 3.      Edward, 4.      Empire, and 5.      Royal.   Information from historic mine plans and reports has been used to determine the depth distribution of economic ore within the Martha deposit. Economic ore (average of 10 g/t Au) in the Martha underground mine was at a maximum width and strike length between a vertical depth of 160 and 350 m. Below this depth the quartz-sulphide lodes continue, but the grade declined to sub-economic grades (< 4g/t Au) at about 575 m depth and economic ore shoots were localised, mainly on the hangingwall side of the lodes. Samples from exploration drill holes indicate that this decrease is associated with a depth zonation from electrum-bearing Zn-Pb-Cu-Ag sulphide ore (average 10 g/t Au) to sub-economic (< 2 g/t Au) electrum-poor Zn-Pb sulphide mineralisation.

Jan 1, 2006

As part of the overall development of a borehole mining system -develop backfilling techniques to reduce possible damage to the environment caused by either the cavities or the piles of sand tailings that result from in-borehole hydraulic mining. (Borehole mining is described in technology News No. 56.) Approach Water filled cavities at the bottom of boreholes are rapidly and economically backfilled by jetting a sand-tailings slurry underwater. How It Works The Bureau of Mines borehole mining system creates a cavity having a horizontal diameter of more than 50 feet. (See photograph). This cavity can be backfilled with much of the sand previously mined. The sand tailings or similar backfill material is dumped by a front end loader into a slurry mixing tank at the rate of about one ton every three minutes. Enough water is added to give a thick, but pumpable slurry. The slurry is pumped down the borehole through a string of 4-inch pipe to the cavity. After passing through a right elbow at the end of the pipe, the slurry is ejected through a nozzle. The resulting slurry jet emplaces the backfill at the outer wall of the cavity. To obtain an even distribution of fill in the cavity, the nozzle is slowly rotated. The nozzle and pipe assembly is supported from a turntable on the surface. See diagram.

Jan 1, 1981

By G. Zhan, P. Mousset-Jones, G. Danko, J. J. K. Daemen, C. Mezei

Paper presented at the conference Risk assessment in the extractive industries, held in Exeter, 23-24 March 1994, and first published London: IMM, 1994, preprint volume. 18pp., 12 refs. (Originally entitled: Tunnel roof diagnosis using a robotic sensor test bed.) An integral roof diagnosis method is proposed to assist in assessment of risk regarding the stability of an excavation. A Robotic Sensor Test Bed (RSTB) is being developed for the characterisation of roof stability. The sensor test bed consists of a sonic/ultrasonic wave response sensor, a laser surface profiler and a surface temperature sensor. These sensors are mounted on an articulated robot manipulator for performing remote-controlled or fully automated diagnoses. A number of laboratory and field sonic/ultrasonic tests were conducted. A high-energy ultrasonic transducer and an impact device were used to resonate rock slabs. The fracture depths of the slabs were found to be inversely related to the measured resonance frequencies. The agreement between identified and actual dimensions was acceptable. Field tests also showed that loose rock on the surface can be clearly distinguished from solid formation by comparing their wave responses. The robotic laser profiler part of the RSTB was used to measure surface geometry. Different scanning methods are being developed to achieve the fastest and most precise measurements and to provide pertinent information about rock joints and major fractures

Dec 1, 1994

Splashing and wave formation has been studied experimentally by using one-seventh water model of CLU (Creusot-Loire Uddeholm) reactor with two different tuyere configurations by using paraffin and water as simulated slag and simulated metal respectively. Experimental results have been discussed in terms of total splash volume, relative slag volume in splash (dispersed-slag phase holdup in splash), wave frequency and wave amplitude with respect to gas injection rate and tuyere configuration at bath heights between 0.25m and 0.38m. Gas flow rates ranged from 0.00599m3/s to 0.01312 m3/s. The results of splash measurements showed that splash volume increased with increasing gas flow rate and decreasing bath heights for both tuyere arrangements. However, off-centre configuration resulted in relatively higher amounts of splash. The slag volume in splash (Dph in splash) was also found to increase with decreasing bath heights and increasing gas injection rates. The high speed photography revealed that the frequency and wave amplitude increased with gas injection rate. The experimental results also showed that the frequency and vertical displacement of the rotating wave increased when the tuyere orientation became off-centered. This might be used to explain why off-center configuration resulted in generating higher splash volumes than the center configuration.

Jan 1, 2004

By Ross Nairn

"Tulawaka Mine is a joint venture between Pangea Minerals Limited 70% (a wholly-owned subsidiary of Barrick Gold Corporation) and Northern Mining 30%. Tulawaka Mine is located in North West of Tanzania in the Lake Victoria Goldfields. Tulawaka Mine is scheduled to process 360,000 tonnes per year at an average 11.5 g/t head grade over a 4 year mine life.The Tulawaka Process Plant uses single stage crushing, single stage SAG milling, gravity, intensive leach of gravity concentrates, CIL, Zadra desorption and cyanide detoxification to process the ore. Gold recovery exceeds (or is expected to) 95%.The Process Plant was designed and constructed under the supervision of Ausenco Engineering of Australia. Site works commenced in January 2004, Process Plant construction commenced in July 2004 and the first ore was presented to the Process Plant 26th February 2005. The first gold was poured on 15th March 2005. All construction contractors were demobilized from site 7th April 2005. Major achievements have been 3.4 million hrs LTI free during construction and operation to date, training of the Tanzanian workforce at Bulyanhulu Mine prior to commissioning, a succession plan to replace expatriate personnel with Tanzanian staff and significant over performance of the Process Plant against design.INTRODUCTIONTulawaka Mine is situated approximately 160 km south west of Mwanza in the western Lake Victoria Goldfields District of north western Tanzania. The property is held under a joint venture between Pangea Goldfields Inc (70%), a wholly owned subsidiary of Barrick Gold Corporation, and Explorations Minieres Du Nord Ltée (30%). A location map showing the position of the operation in Tanzania is shown in Figure 1.Mine site staff at Tulawaka comprises a combination of Tanzanian and Expatriate personnel. All Pangea personnel live on site and commute to their place of residence for their R&R on a 9 weeks on 4 weeks off roster."

Jan 1, 2006

By T Grenne, R. B. Larsen

Paper presented at the conference on Economic geology in Europe and beyond II, models for mineral deposits in sedimentary basins, held in Keyworth, UK, 13-14 April 1994. Paper originally entitled: Processes in a newly discovered sulphide-PGE mineralisation in Norway. The Stormyrplutten mineralisation is hosted by a minor tholeiitic metagabbro of low-Ti composition intruded at a high level in the volcanic lithology. It is thought to be the subvolcanic counterpart of submarine basalts generated during an extensional episode of ensimatic arc evolution. The sulphide-PGE mineralisation occurs as stratabound pyrite, pyrrhotite and chalcopyrite disseminations with average grades of 376 ppb Pd, 313 ppb Pt, 40 ppb Au, 0.5% Cu and 0.08% Ni in a deposit 15-25 m thick. Locally the PGE content peaks at 2 ppm over 1 m. Microprobe analysis isolated 14 different platinum-group minerals, dominated by sperrylite, temagamite and borovskite and occurring as 1-20 micron compounds embedded in the main sulphide minerals or along the sulphide/silicate grain boundaries. Mantle-normalised plots reveal strong depletion in Os, Ir and Ru and enrichment in Pt, Pd, Cu and Au. The general decrease in Pd and Pt and increase in S up through the stratigraphy is similar to PGE distribution in the Darwendale subchamber of the Great Dyke in Zimbabwe, and may reflect strong fractionation of Pd and Pt in favour of the first droplets of sulphide melt; two reversals of the trend at the 4 and 12 metre levels represent replenishment with fresh magma and repetition of the cycle. In contrast to the Darwendale system, Cu and Ni also show peak concentrations in the first-formed liquids and Pt appears to have fractionated more strongly into the sulphide melt than Pd

Aug 1, 1995

By S. M. Spottiswoode

Crush pillars are widely used in mine workings on the Merensky Reef in the Bushveld Complex to prevent panel collapses. Crush pillars are expected to fail as or soon after they emerge from the face and failure should occur non-violently. Unfortunately, violent failure occurs frequently and is said to be the main cause of seismicity associated with mining of the Merensky Reef. Recent work by Napier, Malan, and du Plessis has shown that limitequilibrium quasi-static models are able to simulate pillar failure using three states of strength of rock in pillars, namely intact, residual after failure, and decayed strength after later time-dependent (viscous) weakening. We have previously introduced an additional state of strength to account for the dynamic failure that results in seismic events, and found that this approach could be used to generate synthetic seismic catalogues similar to observed seismicity for deep-level gold mines, where seismicity takes place mostly on advancing faces. The less brittle seam material of the Merensky Reef, compared to the brittle quartzites and lavas of the Witwatersrand reefs, results in little or no face bursting and is modelled with an assumed plastic strain of some 0.005 over an effective stope width of 2 m before failure. When this plastic yield is surpassed, we allow the reef to fail ?seismically?. We show that synthetic seismic catalogues modelled in this way have some of the features of observed seismicity. Analysis is greatly facilitated using our custom-built software that reads the mine?s survey data into a database and presents results in an interactive graphical form.

Jan 1, 2014

By X Meng, W. A. Hustrulid, M. K. McCarter

Rock excavation in both surface and underground mining is largely accomplished using the drill and blast technique. At the perimeter of such excavations, cautious blasting procedures are often employed to minimize unwanted damage to the remaining rock. Of the several different techniques available, the use of explosive charges with a diameter smaller than the holes in which they are introduced (so-called decoupled charges) is the most common. In spite of the long and widespread use of the technique, a technically sound basis for relating the borehole wall pressure to the explosion pressure is still lacking. Such a relationship is required for optimal design

Jan 1, 2005

Although not immune from the problems affecting the U.S. economy generally, the mineral industry in 1991 contributed nearly $300 billion in the value of processed materials of mineral origin. Supporting this contribution, the Bureau of Mines continued the research and analytical programs highlighted in this annual review. Featured in 1991 were such relatively new programs as minewide monitoring applications in ground control and advances in processing of ceramics and composites, along with more traditional research into health, safety, and mining technology, minerals and materials science, and environmental technology. Under Bureau sponsorship, a National Minerals Policy Forum brought together some 200 executives from industry and Government concerned with minerals policy to begin a dialogue on developipng a policy statement on current minerals issues. A major feature of the forum was the keynote address by Secretary of the Interior Manuel Lujan, Jr.

Jan 1, 1992

By K. D. Russ, A. J. Beer

Non-contact systems for measuring underground voids have used theodolites, reflective or non-reflective laser methods and sonar techniques. An effective but cheaper alternative is based on use of a Wild T1000 electronic theodolite coupled to a Leica Data DISTO and a Wild GRE3 data logger. The software used to process the theodolite data is a spreadsheet and macro combination, while Surpac, Datamine and AutoCAD modelling packages have been investigated for viewing the tunnel profiles. The main limitations were found to be blinding, when irregularities in the stope obstructed the line of sight, and the 30 m range of the Data DISTO model used in the study, although more powerful models are available. All three modelling packages proved suitable, with Surpac providing the best-quality printed images of the voids surveyed and AutoCad by far the cheapest alternative

Jun 21, 1905