Search Documents

By J. P. Neumann, L. Raymond

At temperatures near 1000°C, only the (112) (111) slip systems are operatire in tungsten. Therefore, the substructure introduced into the billet upon rleforming a single crystal by rolling at 1000 "C can be controlled by proper selection 01. processing ral'iubles. Using a reduction of 10 pct pel- pass, the (001)[110] and the (110)[001] crystals will deform by duplex slip rip to a 50 pet reduction in thickuess. These rolled single-crystal sheels are characlerized by anisotropic hardening, retention of ductility with warm working, lattice bending which is related to the conlacl (angle, and macroscopic dimensional changecs in the length bid not the width of the billet. When several slip systems become operative, a greater degree of work hardening is itztvoducetl into the crystal. This rolling- condition is characlerized by isotropic hardening, loss of ductilily with warm working, complex lattice distortions, and macro-scopic dimensional changes in both the length rind Width of the billel. IN tungsten, the {1 10}(111) slip systems are operative below room temperature,' while above 700°C only the {112{ (111) slip systems are observed.2,3 In the transition region, i.e., room temperature. both systems appear. It is the purpose of this investigation to show that tungsten single crystals deformed by rolling at a temperature where only one slip system is operative generate dislocation substructure which depends on the crystal orientation. For a specific crystal orientation. the resulting dislocation substructure can be further influenced by modifying the rolling procedure. Crystals oriented for multiple slip display less substructural sensi- tivity to modifications in processing techniques than do single crystals oriented for duplex slip. Under simple slip modes of deformation, very little work hardening is introduced into a rolled single-crystal sheet. Mechanical properties such as room-temperature strength. ductility, and hardness are used to confirm the existence of the different work-hardened conditions generated within the crystal by modified warm-rolling techniques. EXPERIMENTAL PROCEDURE Material. Single-crystal billets of four different crystal orientations. grown by the Arc-Verneuil technique. were ground to a size of 0.25 by 0.375 by 3 in. In terms of their rolling plane and rolling direction, the billets had the following orientations: (1101 [001 ] (110) [110] (001) [110] (001) [100] The actual orientation of all crystals was within 5 deg of the ideal orientations. The typical impurity content of the crystals is given in Table I. Polishing and Etching. Polishing was done elec-trolytically in a 20 g per liter aqueous solution of NaOH at approximately 10 v. It was established by the Laue back-reflection X-ray technique that the surface damage due to grinding and cutting operations with a diamond wheel did not exceed 0.001 in. Therefore after each cutting or grinding operation at least 0.002 in. was removed electrolytically from the surface in order to eliminate surface effects. By lowering the voltage to 3 v, subgrain boundaries and individual dislocations are identified in agreement with Berlec 4 where the etch-pit traces on a cubic plane form a square. The etching time was about 5 sec at room temperature. Rolling. Rolling was carried out on a Loma 2-high mill (Model 600). The peripheral velocity of the 6-in.-diameter rolls was 500 in. per min, with the surface temperature of the rolls about 400° to 450° C The billets were heated before each pass for 30 min in argon to 1000 C. Oxidation of the crystals during rolling in air resulted in a thin layer of greenish-yellow WO 3 This oxide was removed after each pass by immersing the crystals for a few minutes in a boiling NaOH solution. Prior to the initial rolling pass, a surface layer of 0.001 in. was removed by polishing. The crystals were then annealed in vacuum (10-4 torr) at 2400 C for 30 min. All crystals were rolled in the same direction; i.e., the same end was always introduced into the rolls. The rolling program was conducted in

Jan 1, 1965

Development of aggregate resources for use in structural concrete has been encouraged in Japan to support infrastructure improvement and national land conservation. Natural aggregate is a valuable resource necessary for sound economic development, and its importance is growing. After completion of aggregate mining projects, planting and afforestation are implemented. But sandy soil in excavation sites is not optimum for the growth of vegetation, and many years are needed before forests are restored. Planting techniques should be improved to support efficient reforestation in a shorter period of time. For this purpose, problems hampering growth of vegetation must to be solved through application of physical and physicochemical techniques to ensure that the environment and the ecosystem will be conserved in project sites.

Dec 6, 2010

By Benjamin Cebrian

Traditional dilution control systems range from computer modeling, use of physical markers on the field as polypipes to a technology that marks some control points where displacement is measured. The latter includes walking over a muckpile which is prohibited by some mining companies as a safety measure. The new technology presented in this paper is a patented system that is installed on board excavators (backhoe or front shovel types). Several control points are set along ore/waste contacts and their position is uploaded on the corresponding shovel. The operator proceeds on mucking until he is alerted when reaching any of the several control points previously located in the blast patterns and that have moved with the muckpile. A case study is presented at a high grade copper mine, were unique 3D shapes are showing as a result of using an on-board excavator dilution control system. Both ore-loss or dilution cost of opportunities are analyzed.

By Gyimah Kasali

Rapid Load Testing was performed as part of an extensive drilled pier testing program for the University of California Berkeley Capital Improvement Program. The purpose of the program was to: (1) Verify the axial compressive design capacity values for the planned 24" piers, and to estimate the capacity of the existing 30" CIDH piers, and (2) To evaluate the seismic performance of the proposed drilled shafts. The Fundex PLT was used since the loading period of the PLT is very similar to the period of a seismic event, making it an ideal tool to model the pier response to seismic events. "Performance-based design" of structures subject to seismic loads has been of particular interest to UC Berkeley Seismic Review Committee and the Pacific Earthquake Engineering Research Center. The comparison of static tests to Rapid Load testing also provided valuable correlations. The program represents one of the most comprehensive drilled pier test programs on the West Coast. The testing program consisted of Rapid Load Testing using the Fundex PLT on 6 drilled piers. Rapid Load Tests were followed by conventional static compression and tension tests on selected piers, followed by another cycle of rapid load tests on the statically tested piers. The piers featured extensive instrumentation to allow detailed interpretation of the test result. Correlations were drawn to compare static load test result to that of the PLT in the particular soil profile, and the PLT also provided the data to analyze the ultimate seismic capacity of the piers. The load test results indicate that the ratio of interpreted failure load from the PLT data to the corresponding load from the static load test data is about 1.2 to 1.3 for the clayey soils underlying the test site. The results also indicate that the PLT offers an economical approach to defining the stiffness of drilled pier foundations subjected to seismic loads for use in performance-based design.

Jan 1, 2002

By Sean Gallagher, Gene Wilson, Christopher Mark, Craig S. Compton, Gregory M. Molinda

Falls of small pieces of rock from between roof bolts continue to cause fatalities and to injure hundreds of coal miners each year. Roof screen is the most effective way to prevent these incidents, but some mines are reluctant to use it because they believe installing screen can be awkward, expensive and time-consuming. The most common type of roof bolting machine used in mines today is the dual boom, outside-controlled roof bolter. Mines who install roof screen using these machines have developed some machine modifications and techniques to ease roof screen installation. This paper describes some successful techniques and machine modifications that are being used in productive mines to assist with roof screen installation. Since the material handling involved with roof screen installation can expose miners to an increased risk of musculoskeletal injuries, the National Institute for Occupational Safety and Health (NIOSH) ergonomists, designed machine modifications and implemented a series of tests to evaluate roof screen handling procedures for outside-controlled, dual boom roof bolting machines. Roof screen installation can also have a positive economic impact on a mine by reducing the cost of injuries, workers’ compensation, required spot or re-bolting, and clean-up of long term travel and belt entries.

Roof falls in coal mines typically occur in or around intersections and this has not changed in the last two decades. This research develops an improved scientific understanding of stress distribution and associated failure behavior around 4-way and 3-way coal mine intersections. Three-dimensional numerical analyses were performed to determine factors that influence intersection stability. The analyses used Hoek-Brown failure criterion. Failure zones around 3-way and 4-way intersections were developed. Intersection span and horizontal stress have a major influence on intersection stability. For the 4-way intersection, pillar corners across the intersection fail first and lead to progressive failure of immediate roof and floor layers. The mechanism of failure is similar for the 3-way entry but the shape and extension of failed zones differ. Coal ribs mostly fail due to tensile stress, while roof and floor strata fail due to shear stresses. Rib corners fail due to a combination of shear and tensile stresses. In addition to stress distribution; safety factor contours analysis was performed to assess stability of intersections.

Feb 27, 2013

By Beardsmore G. R

Geothermal gradients in the Gippsland Basin commonly exceed 35¦ C/km. Consequently models of thermal maturation may indicate exploration targets with an anomalous age/depth distribution. However regional geothermal models are constrained primarily by observations of surface heat flow. High geothermal gradients may simply reflect the presence of low conductivity coal beds within the basin. Heat flow data are not readily available for the Gippsland Basin. Normally special purpose drill holes are required to provide direct determinations of surface heat flow. These provide core samples for thermal conductivity and allow measurements of a stable geothermal gradient at least one year after drilling. Different indirect procedures are now required to provide estimates for the Gippsland Basin. Bottom hole temperatures can be used with suitable corrections to provide an indication of the regional geothermal gradient. However the corresponding thermal conductivities are more difficult to determine. Geophysical logs can be used to detect the major lithologies but detailed statistical analysis is required for numerical estimates. Complex mixing models are now suggested for geothermal surveys linking physical properties to variations in the mineralogy of each well. Allowing for low conductivity coal measures the data in the Gippsland Basin suggest values for heat flow consistent with regional trends in Australia. Interpretation is complicated by overprinting of transient thermal events with different time scales. Apart from the tectonics of basin evolution geothermal signatures may be complicated by regional ground water migration, the 'hot spot' trace associated with southward younging of Cainozoic volcanism, diagenesis, and basin refraction.

Jan 1, 1992

By Dominic Orf, Gregory Poole

On December 12, 2018 at 4:14 AM EST, an earthquake registering a 4.4 magnitude on the Richter Scale occurred in central Tennessee. According to a survey posted on the USGS website, this earthquake was felt throughout the southeast and even as far away as Arnold Nebraska. That’s over 900 miles (1,448 kilometers) from the epicenter. We recorded the vibrations from this earthquake on 44 different seismographs that were set up with remote access to continuously monitor vibrations from blasting activities. Having this data gave us an opportunity to compare the vibrations caused by earthquakes and blasting. A simple observation of the amplitudes, frequencies, and durations is enough to notice that vibrations from earthquakes are very different than vibrations caused by blasting in mining and construction. We were also able to observe the dissipation of the vibrations from the earthquake and see if the low frequencies, that are typical of earthquakes, dissipate at a consistent rate. Regression calculations were performed in order to see if there was a good data fit and if a specific vibration prediction could be made based on the magnitude of an earthquake. “How does quarry/mining/construction blasting compare to the Richter Scale?” This is a very common question that we get from homeowners when discussing vibrations due to blasting activities. This paper is intended to provide some simple answers for such a complicated question. Both the Richter and Mercalli scales are compared to the particle velocities as they were recorded from this earthquake.

By R. Ward Stahl

Fire is still a scourge of the mining industry, although many precautionary measures have been and are being taken to reduce the incidence of fires and to combat them. Generally, the success of fire extinguishment is directly proportional to the speed of attack, and the speed of attack in turn is dependent upon the availability of materials and trained personnel. Preparations for firefighting are frequently neglected because they are considered emergency needs and do not contribute directly to coal production. Fire incites panic--a fact often overlooked--but such chaos can be minimized by training people in the use of equipment and procedures. Heat, smoke, and fumes hamper the approach to a fire; however, a relatively new technique of attacking fires with high-expansion foam may well contribute greatly to firefighting. The foam is transported to a fire and used at a considerable distance, thus permitting the firefighters to work more safely.

Jan 1, 1962

By Penrose E. K

With the exception of occasional periods, when up to 80% of oxidized ore was treated, the G.M.K. plant treated all sulphide ore until October, 1939. The treatment was, briefly, as follows:The ore was ground to approximately 17% plus 200 mesh Tyler and agitated in cyanide solution, after straking. After agitation, the pulp passed through two stages of counter-current decantation washing in Dorr thickeners and was filtered once, to complete the precyanidation stage.The precyanide filter cake was repulped with flotation circuit solution and floated in a Denver Sub A flotation machine, consisting of twelve cells. The concentrates were roasted, cyanided and filtered four times before disposal to the' dam. The flotation tailings were thickened to conserve water and pumped away to a separate dam.The average results of flotation operations for the six months before October, 1939, are shown in Table 1.

Jan 1, 1942

The method of investigation was to study the distribution of ore in great detail, to make a thorough structural study of the lode and the mine area, and then to compare the results of the two studies. Such a comparison usually reveals a very close relationship between geological structure and ore distribution, and can often lead to important conclusions which would not be reached in the ordinary working of a mine.The Triton mine lies 30 miles E.N.E. of Cue, or 380 miles N.W. of Kalgoorlie, in typical pre-Cambrian rocks, consisting of gTeenstone lavas and tuft's, interbedded with slates and some sediments, and intruded by granite and porphyry. Fig. 1 (at end of paper) is a longitudinal section of the mine and shows that the workings consist of the main North Emu and the smaller South Emu, separated by a distance of about 1 of a mile. Both orebodies occur on the same lode, which strikes north and south and dips practically vertically. On the same line, and of 1/2 a mile and a mile respectively to the north of the North Emu, are the small Rand and North Rand workings, where a big width of lode material has proved to be very low grade. In the North Emu the lode width averages 12 to 15 feet; it is seldom less than 5 feet and in places reaches 30 feet. In the South Emu the lode is wide, but only portion of it is payable.The lode is a mineralised bed occurring between massive lava flows on the east and a mixed series of tuft's and thin lava flows on the west. The lode material is hard, fine grained, and dark coloured, and generally has a faint banding which is believed to indicate a tuft'aceous origin of the original lode rock. Microscopic examination shows that the original lode rock has undergone considerable albitisation;' there has also been considerable formation of biotite which gives the lode material a characteristic sheen. The mineralisation consists of abundant fine pyrite, which is auriferous, and a lesser development of pyrrhotite which is, however, barren of gold.THE OREBODIES AND THEIR CHARACTERISTICSThe distribution of ore is best studied from gold contours, as these reveal features that cannot be detected in an ordinary assay section. Gold contours (see Fig. 3) are developed' by plotting the width and grade of all development and stoping assays throughout the mine on a longitudinal projection, representing each sample by a coloured dot according to a suitably chosen range of assay values, and then outlining areas of similarly coloured dots (see H. J. C. Conolly, Econ. Geol., April, 1936). Both width and grade must be taken into account and the simplest method of gold contouring is to use dwt.lft. values, but difficulties arise here with big widths of low grade and small widths of high grade ore. To choose an extreme case, 30 ft. of 2 dwts. and 2 ft. of 30 dwts. both equal 60 dwts.lft., and would therefore be given the same value in dwt.lft. contouring...

Jan 1, 1943

By H. A. Dierks

Implementation of the joint Federal-State control program established in 1955 to cope with the mine water problem in the Pennsylvania anthracite region is described in this report. The increasing severity of the water problem in the anthracite mines has necessitated major adjustments as this continuing program has progressed. Since 1941 the Federal Government has recognized the mine water problem as an important factor in the worsening economic condition of the anthracite region by initiating scientific and technologic investigations and establishing the Anthracite Flood-Prevention Section in the Bureau of Mines in 1948. On the basis of comprehensive investigations and studies, the results of which were published in numerous reports and bulletins, the Anthracite Mine Drainage Commission of the Commonwealth of Pennsylvania formulated a plan that served as a background for legislative action in 1955, resulting in Public Law 162, 84th Congress (Act of July 15, 1955 (69 Stat. 352; 30 U.S.C. 571-576)), for the Federal Government, and Act No. 82 of the General Assembly, July 7, 1955, for the Commonwealth of Pennsylvania. The report covers 29 mine flood control projects approved and executed in implementing the aforementioned legislative acts. Essential engineering and cost details for each project are given, together with an evaluation of the effect that the installed facilities have on alleviating the mine water problem as it concerns individual mines and the anthracite industry as a whole.

Jan 1, 1962

By N. Behnood

"This paper describes how material selection, quality assurance, and failure investigation play important roles in the efficiency and safety of mining and metallurgical operations.INTRODUCTION Material selection, quality assurance, and failure investigation are all complementary elements of materials engineering in the application of materials technology for failure prevention. Based on commodity price increase of 300% between 2002 to 2013 [1] and increased cost ofcapital projects and operation, equipment failure, which in some cases causes complete shutdown of the operation, becomes a vital importance in mining and metallurgical plants. The following sections present a number of examples from many failure cases experienced by the author during his three decades of work as a materials engineer in the mining industry."

Jan 1, 2015

By R. Sullivan, K. Joiner, B. Emery, M. de Vries, F. A. Stober, L. R. Nelson, J. M. A. Geldenhuis

Keywords: Pyrometallurgy, smelting, converting, furnace design, furnace retrofit, high-intensity smelting, copper coolers, plate coolers, waffle coolers, tap-blocks, lower sidewall air-cooling, wall hold-down system, platinum group metals, ferroalloys, ferrochrome, ferrocobalt, ilmenite smelting, ironmaking, operational readiness, operational support The paper describes the development of furnace designs by Hatch in conjunction with the smelting plants in Africa to meet the intense process requirements in certain applications; continued improvement in operating efficiency through increased throughput from existing crucibles; and improvement in campaign life and furnace integrity. The era of Hatch in Africa has seen the doubling of furnace power in retrofit projects using existing crucibles to developing the highest intensity immersed electrode operations in the world. This has resulted in minimized OPEX and CAPEX per unit of production. Through the continued development of its cooling, binding and furnace power supply technologies and working with the experienced and knowledgeable personnel at the smelting facilities in Africa, Hatch has managed to meet the challenges of ever increasing furnace process requirements associated with increased power density and superheats prevalent in the operations. In addition to developing furnace crucible designs, Hatch has also intensified its ?after sales service and support? with the construction, commissioning and start-up technical assistance and operational readiness and operational support for ramp-up to nameplate capacity and beyond. The key areas of furnace risk associated with high superheat molten material tapping has also seen the development of diagnostic systems to mitigate risks and produce early warning signals for the operators.

Jan 1, 2006

By F P. Hao

Organo-sulphur-based collectors (eg xanthates, dithiocarbamates and dithiophosphates) are widely used in the flotation of sulphide minerals. Xanthates (ROC(=S)Sû), for example, adsorb strongly at sulphide mineral surfaces, in a reaction that is electrochemically coupled with the reduction of dissolved oxygen. One of the oxygen reduction products, hydrogen peroxide, reacts directly with dissolved xanthate, leading to its oxidative decomposition. Experimental work has been conducted, using ethyl xanthate, to understand the molecular mechanism by which hydrogen peroxide reacts with xanthates. A number of degradation products have been identified, some of which have not been reported previously. This oxidative decomposition reaction pathway is discussed in the broader context of xanthate decomposition in flotation systems. One of the identified ethyl xanthate decomposition products, ethyl perxanthate (ROC(=S)SOû), has been observed in the process water of a number of mineral processing operations. The interaction of this molecule with goethite (α-FeOOH) particles, typical of that found in tailings dams, has been studied in more detail using attenuated total reflectance (ATR)-FTIR. The ethyl perxanthate molecule has been found to coordinate to iron (FeIII) at the goethite surface, and undergo a surface-catalysed decomposition process. In the presence of both PbII and goethite, a ternary surface complex is formed, where ethyl perxanthate is coordinated directly to surface adsorbed PbII atoms. The results obtained give some insight into the environmental fate of ethyl xanthate in tailings streams, and a basis on which to consider the environmental importance of such species in tailings dams. Strategies for the destruction of residual xanthate levels in waste water streams are discussed in terms of the likely reaction products.

Jan 1, 2002

By J. Riss, S. Gentier, A. Marache

The study of the hydromechanical behaviour of fractured rock masses requires a detailed knowledge of the isolated fractures. The aim of the paper is the simulation of the evolution of the void space, located between both walls of a fracture, during a shear test under constant normal stress. Results of the mechanical simulation model are first validated then analyzed in detail. We observe that, during the shear process, there is an opening of the fracture with the creation of preferential channels. These channels are determined at the early phase of the shear process (pre-peak phase), and we observe during the post-peak phase that void areas increase in size rather than the creation of new apertures. Die Untersuchung des hydromechanischen Verhaltens eines zerlegten Felsmassivs erfordert genaue Kenntnisse der einzelnen Spalten. Ziel dieses Artikels ist die Simulation der Evolution des Hohlraumes zwischen den beiden Wänden eines Spaltes während eines Abscherungsexperimentes unter konstantem senkrechtem Druck. Die Ergebnisse der Modellierung werden zunächst mit dem Abscherungsexperiment verglichen und dann im Einzelnen ausführlich analysiert. Während des Abscherungsprozesses tritt eine Öffnung des Spaltes auf, die die Bildung von bevorzugten Fliesswegen fördert. Diese Kanäle werden bereits in einer frühen Phase des Abscherungsprozesses (pre-peak Phase) festgelegt. In der post-peak Phase tritt dann eher eine Vergrößerung dieser Kanäle, als die Bildung neuer Hohlräume auf. L’étude du comportement hydromécanique d’un massif rocheux fracturé ne peut se faire sans une connaissance approfondie des fractures le constituant. L’étude présentée dans cet article concerne la simulation de l’évolution de l’espace des vides présent entre les deux épontes d’une fracture au cours d’un essai de cisaillement à contrainte normale constante. Les résultats du modèle sont tout d’abord validés puis analysés en détail. On constate que, au cours du cisaillement, il apparaît une ouverture de la fracture permettant la création de chenaux préférentiels. Ces derniers sont déterminés très tôt dans le cisaillement (phase pré-pic), et on observe dans la phase post-pic davantage un accroissement de la taille des chenaux plutôt que la formation de nouvelles zones de vides.

Jan 1, 2003

According to the previous research, it is found that the thickness of cover is mostly less than 100 m for highwall mining system. However, for most of the Chinese surface coal mines, the mining depth is over 150 m; on the other hand, the shovel-truck is the most common mining technology. As a result, a lot of residual coal will be remained around end-walls. Considering these facts, the calculated methodology of highwall mining system under thick cover is presented in this paper. Meanwhile, numerical simulation of highwall mining system under thick cover was carried out. The outcome shows that the calculated methodology for pillar stability of highwall mining system under thick cover presented in this paper is acceptable. In other words, the highwall mining system is feasible to extract the residual coal around end-walls in Chinese surface coal mines. Thus, not only coal recovery ratio can be improved, but also can increase the production life of surface coal mines in China.

Jan 1, 2012

By Enver Alan

This Research & Development (R&D) study was conducted in the field of applied blasting engineering in Ethiopia, within the AKH Railway Project, which was built in Girena, within the boundaries of the province of Mersa, in the Basalt Quarry at km 346, Ashangi Formation, occured in Eocene geological time in the aphanitic trachibasalt. Under the scope of the study, which has been performed to determine the effects of the artificial discontinuities at different depths and the effects of artificial discontinuities through structural damage risk, three test areas, at the same location and same formation, were considered. Six numbers of artificial discontinuities, each 10 m (32, 81 ft) transverse, were created by using pre-splitting and drilling-blasting technology. The number of sequential artificial discontinuities on each test area is two and they have the same length. The length of artificial discontinuities are; 6,80 m (22,31 ft) at the first test area, 13,60 m (44,62 ft) at the second test area and 17,00 m (55,77 ft) at the third test area respectively. The distance between sequential artificial discontinuities is 8 m (26,25ft) on each test area. Thirty-one shots were executed in order to produce vibration (10 shots on the first test area, 11 shots on the second area, 10 shots on the third test area). One hundred and twenty-three seismic recordings were obtained during the execution of the shots by using 4 seismographs. The closest distance between the shot points and the nearest measuring station is 5,30 m (17,39 ft). During the shots, the rock was cracked and there was no fragmentation and/or fly rock. At the first test area, measured PPV values are between 25,40-127,00 mm/s (1-5 inch/s) before the first artificial discontinuity and less than 50,80 mm/s (2 inch/s) after the second artificial discontinuity. At the second test area, measured PPV values are between 76,20-177,80 mm/s (3-7 inch/s) before the first artificial discontinuity and less than 76,20 mm/s (3 inch/s) after the second artificial discontinuity. At the third test area, measured PPV values are between 50,80-279,40 mm/s (2-11 inch/s) before the first artificial discontinuity and less than 50,80 mm/s (2 inch/s) after the second artificial discontinuity. Peak reduction rates in Peak Particle Velocity (PPV) values determined by measuring as follows: In the first test area 95,77% (106,00 mm/s to 4,48 mm/s) (4,17 in/s to 0,18 in/s), in the second test area 79,77% (176,00 mm/s to 35,60 mm/s) (6,93 in/s to 1,40 in/s), in the third test area 95,85% (from 205,00 mm/s to 8,55 mm/s) (from 8,07 in/s to 0,34 in/s). The arithmetic mean of the differences of PPV values (decrease rate) is 82,66% in the first test area, 69,37% in the second test area, and 92,03% in the third test area. The highest sound value is 138,50 dB and is defined as “noise”. When the measured parameter values are examined it was determined on the USBM norm graphs that these vibrations carry a risk of structural damage in the region before the first artificial discontinuity. While passing through artificial discontinuities the vibrations progress by losing energy and the vibrations passing through two artificial discontinuities do not carry structural damage risk under current conditions.

The Resource Management Act 1991 (RMA) and the Crown Minerals Act 1991 (CMA) both came into force on 1 October 1991. The purpose behind RMA was to integrate the existing laws dealing with town and country planning, land subdivision, water and soil, minerals and energy resources, coastal management, air pollution and noise control into one omnibus Act. Originally, there was a section in RMA dealing with minerals. However, this section was taken out of RMA and a companion piece of legislation - namely CMA - was passed with RMA.

Jan 1, 1994

By Ronald E. Heuer

A 1995 RETC paper of similar title presented a method for estimating rock tunnel water inflow based on semi-empirical correlations with borehole water pressure tests. Since that time the author has found the method to be very useful, and it has been used by others in the industry. This current paper is an update which is intended to: A. More clearly explain assumptions and limitations of the method. B. Describe some case history examples. C. Respond to questions which have been raised; and extend the method to other considerations including distribution of inflow along the tunnel, panning requirements, interpretation of tunnel probe hole water inflow, and estimation of potential effectiveness of pre-excavation grouting to reduce water inflow.

Jan 1, 2005