Search Documents

By Maurice Grieves

GC. Waterman Mr. Grieves' paper on "Shaft Sinking Today--A Boring Business Tomorrow" in the Dec. 1981 issue of MINING ENGINEERING is an excellent description of recent improvements in speed and costs of shaft sinking. However, shaft boring techniques are not a recent development. In 1935-36, the Idaho Maryland Co. (gold), Grass Valley, CA, bored the vertical 1.5-m-diam Idaho No. 2 ventilation and supply shaft to a depth of 346 m. The equipment was designed and perfected by Branner Newsome and was, I believe, described in "Transactions." Pickands Mather later bored a 1.8-m-diam shaft to a depth of about 305 m using Newsome's design. The Idaho No. 2 shaft cut through hard gabbro, diabase dikes, soft serpentine, very incompetent ankeritized serpentine and a strong fault zone. The completed shaft did not require timber support; the fault zone was cemented. Equipment consisted of a rotating 1.5-m or 3-m core barrel with a slotted bottom which cut a 76-mm kerf. The cutting agent was chilled steel shot introduced into the slot as needed. The driving mechanism and core barrel were lowered into the shaft, the former secured to the wall and the inshaft "engineer" operated the motors which controlled core barrel rpm and advance. After an advance of 1.5-3 m the equipment was lifted out of the shaft, a half(?) stick of powder cut off the drilled core, and it was hoisted to the surface with a cable attached to an eye bolt at the tope of the core. A "shift" consisted of three men: hoistman, equipment operator (down the shaft), and a surface laborer. Advance was variable as equipment and techniques were perfected. Near the end of the job advance was, as I remember, 1.5-3 m per shift. Costs were, as I recall, about $115/m. Up to 4 m cores were lifted out in one piece and swung to the dump by a stiff leg derrick. The Newsome equipment was relatively inexpensive to build and operate and his method should be (more than?) competetive with the methods described by Grieves. W.E. Hawes The author, in mentioning the South African developments of the cactus grab, ignores the parallel development of the Cryderman mucker in this hemisphere. Perhaps a slightly longer history of blind hold drilling would have been in order. Blind shaft boring got a major boost at the Nevada Test Site, as part of the nuclear weapons development, when it was essential to be able to quickly assess depth for weapons testing. One of the early civilian attempts to utilize this technology occurred when Kerr McGee drilled the shaft at the Section 19 Mine at Ambrosia Lake, NM. This twin masted drill rig belonged to a subsidiary of Kerr McGee, not Shaft Drillers. This was a difficult hole, due to bentonitic shales that decomposed. Later advances in drilling fluids eliminated this problem. The Conoco project referred to is not entirely correct, and needs minor amplification: The depth of the development (not pilot) shaft drilled was 684 m, at a diameter of 3.05 m, with a 2.16 m ID hydratatic casing being installed to a depth of 669 m. Conoco Inc., not Challenger, executed the drilling, however Conoco did use Challenger Drilling Company's Rig 14-S. Rig 14-S is unique in that it is specifically designed for shaft drilling, rather than being an oil field rig used for this service. All work was planned and directed by Conoco personnel. Deviation of the aforementioned shaft from vertical was 31 cm. Two smaller shafts (pilot shafts) were drilled with the same rig. These smaller ones were drilled 1.8 m in diameter, to depth of 665 m and cased with .91-m-diam casing, to depth of 650 m to be used as pilot holes for 5.5 m diameter shafts. The total elapsed time for all drilling, casing, cementing, and rig moves was 50 weeks. The constraints mentioned of vertical accuracy, torque, wall collapse, rig set up time, lining time etc., pumping out, etc., may not be as serious as the author implies. First, vertical accuracy: The record achieved by Conoco indicates that with reasonable care, good accuracy can be obtained, primarily by having a fair amount of weight in tension, rather than on the drill bit. Second, the amount of torque that can be applied to the drill stem has been greatly increased by the introduction of larger diameter drill stems, such as the new Hughes rig uses. Third, risk of collapse of shaft walls is minimal with the proper mud program. Basically, the walls are supported by the weight of the mud and it is not removed until some type of casing is installed and grouted in. Here in the real challenge of blind drilling shafts to devise a more economical method of lining bored shafts than using steel casing. The remaining issues were minor at Conoco, provided adequate planning and scheduling takes place. An excellent paper, "Shaft Drilling--Crownpoint Project" by Hassell H. Hunter, presented at the Fifth Uranium Symposium in Albuquerque in Sept. 1981 contains details of this project. A combination of blind boring, with enlargement by either mechanical means (boring machine, or tunneling type shield) or slabbing down, with muck removal through a larger bored shaft would seem to be the future trend in shaft development. The economics, especially for wet conditions, favor this concept over conventional sinking, as has been demonstrated at Kerr McGee --Churchrock, UNC--Churchrock and Conoco at Crownpoint.

Jan 3, 1983

By Britt H. Hatfield, Jiu-Chiuan Chen, Wen-Ruey Chang, David C. Christiani

Occupational exposures to whole-body vibration (WBV) at different frequency domains may differentially affect human comfort and the musculoskeletal system. Under this presumption, a frequency-based weighting scheme has been adapted in many widely accepted standards for WBV measurement. However, there is very little human data showing a direct link between WBV frequency and musculoskeletal disorders. We conducted an epidemiologic study to examine the association between WBV frequency and prevalence of low back pain (LBP) and to identify determinants of specific frequencies associated with LBP in urban taxi drivers. Methods The WBV frequency data were collected from 247 professional drivers (aged 44.6±8.3) who participated in an exposure validation study 1 of the Taxi Drivers’ Health Study (TDHS) in 2000. 2 In accordance with the ISO 2631-1 (1997) methods, we measured the frequency-weighted acceleration over drivers’ seat surface, under conditions representing randomly assigned destinations. We developed a WBV record-replay system at the Liberty Mutual Research Institute (LMRI) in Hopkinton, MA, USA. This system includes two tri-axial accelerometers (PCB Piezotronics, NY, USA), one RD-130T PCM data recorder (TEAC, Tokyo, Japan), and one LMWBV meter 2.0 (LMRI, MA, USA). Only the vertical axis of seat-surface WBV frequency was used in this study. To characterize the WBV frequency curve, we manually identified the presence of any peak within each of the following frequency range: <4, 4-10, 10-20, and >20 Hz. Information about the operating vehicles and driving environment was either collected from the vehicle registration record (manufacturer, year of make, transmission, engine size, etc.) or directly measured (wheel-base length, seat inclination, etc.). Structured interviews were conducted by an occupational physician to gather information on LBP that had led to medical attention or absence from driving in past year. We used multiple logistic regression to estimate the prevalence odds ratio (OR) associated with the presence of each index peak frequency, adjusting for age, body mass index, professional seniority, daily driving hours, seat inclination, and the intensity of predicted root-mean-square WBV exposure in m/sec2. For any revealed WBV frequency that was associated with LBP, we constructed a multiple logistic regression model to identify the personal and vehicle characteristics associated with the presence of WBV peak within the indicated frequency range.

Jan 6, 2006

Research 82 highlights significant studies conducted during the past fiscal year at Bureau facilities and offices. Readers who want more information about the projects and studies summarized here can contact the researchers whose names and locations appear with each summary. General information on Bureau of Mines programs is available from the Office of Technical Information, 2401 E Street, NW., Washington, D.C. 20241. A listing of principal officials, a location map of field facilities, and a selected bibliography of publications and patents issued on Bureau developments during the past 3 years are provided.

Jan 1, 1982

By A L. Withy

This paper is intended as a review from a planner&apos;s viewpoint, of the relationship between town and country planning, a primarily government activity, and the minerals industry, which, with the exception of coal, is a largely private enterprise activity. The paper first considers the nature of the system of planning in New Zealand, and the objectives sought by planners in relation to minerals are discussed. The reasons why these objectives are not generally being achieved are investigated. A final section deals with the gap between objectives and achievement, and suggests a number of ways in which this gap may be narrowed.

Jan 1, 1976

By D. A. Stanley

The Bureau of Mines conducted laboratory-scale experiments to determine whether or not surface waters with a high organic content could be purified sufficiently to be used to replace the natural high-quality deep well water currently being used in the silica flotation step of phosphate rock beneficiation. Waters abundant in organic matter were collected from two central Florida streams, flocculated with a cationic polyethylenimine polymer, and processed in a sand filter. This treatment removed most of the organic materials from the water. Untreated surface water, treated surface water, and distilled water were used to compare the flotation response of the acid insolubles in an amine flotation circuit. Surface water treated with PEI-1000 was shown to be as effective as distilled water for the acid-insoluble-flotation step. Flocculation and filtration can therefore produce water suitable for amine flotation of quartz, which would permit substitution of surface water for deep well water.

Jan 1, 1981

By Richard H. Bares

One criterion central to most definitions of reclamation is the restoration of mined lands to their original productive potential. This is often difficult to achieve on mined lands in the Northern Great Plains because of the rigorous climate (Bares 19;2) and various soil related problems including sodicity, salinity, soil permeability, low organic matter and plant nutrient deficiencies (Malakondaiah and Safaya 1982). Field study sites were established on recontotured mined areas during the early 1970&apos;s (prior to the topsoil mandate) in which several amendments were tested for their ability to improve spoil/topsoil conditions and, hence, increase plant production. Physical and chemical properties of these control (untreated) and amended spoils and topsoils have been summarized (Safaya et al. 1982). A number of grass and legume species combinations were studied. The general effects of one time (prior to seeding), single rate (approximately 100 mT ha-1) application of leonardite and/or slack coal to spoils and topsoils was the reduction of grass dry matter yields (NB 1 test site: dry matter yield (DMY) without slack was 110 g m 2 yr I ; DMY with slack was 80 g m -2 yr 1 I and the promotion of legume establishment and yield (SB test site: DMY without leonardite was 13 g m 2 yr -1; DMY with leonardite was 93 g m 2 yr 1). On South Beulah topsoil, treated with leonardite, production of weedy species was remarkably lower than that without leonardite (SB test site: DMY without leonardite was 252 g m - yr -1; DMY with leonardite was 177 g m 2 yr 1). The general effect of commercial fertilizer applied one time prior to seeding (rates ranging from 9-13-0 to 44-1 12-28 kg ha-1 of N-P-K) was to increase plant production during the first two to three years after which the effect disappeared. This effect was much more pronounced on spoils (NB I test site: DMY on spoils without fertilizer was 53 g m -2 yr -1; DMY on spoils with fertiliser was 132 gm -2 yr -1). Weedy species accounted for most of the biomas, production during the first growing season. Three of the test sites were designed to study plant production on topsoils and spoils. Establishment and production of grass species were comparatively better on topsoils (30 cm in depth) than on spoils while legumes were most successful on the soils (Center test site, 1979; DMY of grasses on topsoil was 170 g m 2 yr -1 DMY of grasses on spoils was 52 g m -2 yr -1; DMY of legumes on topsoil was 20 g m -2 yr -1; DMY of legumes on spoil was 191 g m 2 yr -1). Total plant production on topsoiled (302 m thickness) plots at the South Beulah site (DMY in 1979 of 269 g m 2 yr 1) was comparable to that of native western wheatgrass prairie (DMY of 262 g m -2 yr -1). An experiment was conducted to find out if time of planting would have any effect on establishment of grasses on spoils. It was fund that late fall seeding was superior to spring planting for establishment of wheatgrasses at NB 3 test site (Control Plot, 1975: DMY on spring-seeded was 1 g m -2 yr - 1; DMY on fall-seeded was 55 g m -2 yr -1). In general, wheatgrasses (slender, streambank, thickspike and western) yielded the most aboveground biomass of all the grass species tested; yellow sweetclover was the most successful legume. Yellow sweetclover established and was productive on both spoils and topsoils but only where competition with grasses was apparently minimal. Durar hard fescue established and thrived on topsoil but dry matter production was low compared to that of wheatgrasses. Emerald crown-vetch demonstrated a potential for growth on spoils where water conditions were adequate, whereas side-oats grama, prairie sand-reed, alkali sacaton, and bird&apos;s -foot trefoil demonstrated only sporadic success. Little bluestem did not become established at any of the test sites. Peak production of the planted species, especially grasses, was generally reached by the second week of July. Legume and weed production continued to increase into late August.

Jan 1, 1982

Removal of Thiocyanate from Solutions by Precipitation

Sep 13, 2010

By M. Olper

The zinc recycling is assuming more and more importance. A lot of zinc secondaries and wastes are ready to be collected and converted to zinc metal. The impurities present in these materials and the technical and economical problems that some traditional ways of treating these materials are facing, call for new technologies. The EZINEX Process, a fully hydrometallurgical process industrially proven to convert oxidised zinc bearing materials directly to zinc cathodes, is an innovative process that can deal with any kind of zinc waste/secondaries in a very powerful way. In this paper the highlights of this process will be shown and discussed to demonstrate the robustness of the process and its economic viability.

Jan 1, 2008

By Javier Enrique Basurco Cayllahua

In this work, a gram-positive bacteria was used as biosorbent to elucidate the aluminum load capacity under different conditions related to metallurgical and chemical plants. The sorption data followed the Langmuir, Freundlich, Dubinin-Radushkevich isotherms. In order to determine the best isotherm fit, three error analysis methods were used to assess the data: correlation coefficient (R2), residual root mean square error (RMSE) and Chi-square test. The error analysis established that the Dubinin-Radushkevich model fits better the aluminum biosorption data. The maximum sorption capacity was found to be 41.59 mg.g-1. The maximum removal of aluminum was 95% at pH around 5. The experimental kinetics data was evaluated considering two models (pseudo-second order and pseudo-first order). This study indicated that the R. opacus is an environmental friendly biosorbent.

Jan 1, 2009

By G. B. Amicucci

Golden Sunlight Mines Inc. operates an open-pit gold mine and cyanidation plant about 11km (7 miles) northeast of Whitehall, MT. Golden Sunlight is a subsidiary of Placer Dome US Inc. Mining is accomplished with conventional open pit drilling, blasting and hauling methods. The mining rate is about 102 kt/d (113,000 stpd). Gold occurs as fine-grained disseminations in a pipe-shaped breccia and in immediately adjacent country rock. The ore body is low grade, averaging 2 g/t (0.059 oz per st) of gold. The metallurgical plant uses conventional carbon-in-pulp (CIP) technology. Daily throughput averages 6.5 kt (7000 st). Recoveries are enhanced through a sand tailing retreatment facility while a preaeration process reduces operating costs. The low grade ore dictates that maximum mill throughput at the desired grind size be maintained. Therefore, in October 1988, an Armco Autometrics (now Denver Autometrics) particle size monitor (PSM) 400 was commissioned. The PSM 400 is an on-line instrument. It measures particle size and percent solids in a slurry stream. The PSM pulls its own sample, deareates the sample and passes it through diametrically opposed ultrasonic sensors. The unit uses ultrasonic sound to measure the deareated slurry stream&apos;s particle size and percent solids.

Jan 1, 1991

By Harry L. Siebert

A major Arizona highway project is jeopardizing site safety and security because of the lane rental policy. One million cubic yards of rock must be fragmented to provide two additional lanes parallel to the existing roadway. Traffic is stopped during blasting operations.

Jan 1, 1997

By H. Hamza

Oil sand tailings are disposed of in large ponds in which MFT (Mature Fine Tailings, a stable suspension of fine particles in water) forms after many years of settling. Long-term storage of large volumes of MFT is costly to maintain and also poses an environmental liability. The Advanced Separation Technologies laboratory at CANMET Western Research Centre has worked closely with oil sand companies to eliminate MFT generation by applying paste technology to oil sand tailings. In this process the fine tailings are flocculated to produce a thickened material that has the potential to consolidate to a dry landscape, while warm water is recovered and recycled for reuse in the extraction process. This paper presents some results of an extensive technical program involving bench-scale tests for flocculant selection and continuous thickener pilot tests.

Jan 1, 2002

In 2006, a total of 2,113 coal mining operations reported employment to the Mine Safety and Health Administration (MSHA).1 Coal mines comprised 14.2% of all mining operations. ? Bituminous mines comprised 92.5% (n=1,955) and anthracite mines 7.5% (n=158) of coal mining operations. ? Approximately 71.0% of all coal mines were located in three states: Kentucky (29.2%), West Virginia (21.8%), and Pennsylvania (20.3%).

Jan 1, 2008

By Cotton R. E, Cox R

Digger Rocks is one of several nickel-bearing sulphide deposits localised within komaLiitic volcanics of the Forrestania Greenstone Bell within the Archaean YiIgam Block of Western Australia. Exploration and evaluation to April 1990 have delineated a resource, at a nominal cut-off grade of 0.5 per cent Ni, of 1.9 Mt at 1.1 per cent Ni within a lensoid sulphide body which strikes NW, dips 50&#176;SW, and occurs at a depth of 30 - 110 m below surface. There has been no production from any of the Forrestania nickel deposits to-date. The deposit, comprising both disseminated and massive sulphides, has maximum dimensions of 400 m strike, 115 m vertically and 90 m true width. Generally the massive sulphides occur at the base of the disseminated sulphides, on or close to the base of the Digger Rocks dunite. The two main massive sulphide lenses have maximum dimensions of 120 m strike, 75 m vertically and 16 m true width (northern lens) and 60 m strike, 25 m vertically and 4 m true width (southern lens). The average grades of the massive and disseminated sulphides are 5.9 per cent i and 1.2 per cent i respectively. The massive sulphides generally have sharp hangingwall and fOOlwall contacts and display strong internal grade anisolropy.The massive sulphides are mainly within the supergene zone and consist of violarite, pyrite and marcasite. The disseminated sulphides are mainly within the primary zone and consist of pentlandite, pyrrholite, pyrite and minor chalcopyrite. Alteration zones, up to six in number, are complex in detail. The sulphides are capped by an average of 30 m of sub-economic, leached, siliceous, oxidised material.A genetic model for the deposit is described which places Digger Rocks in Category 2 (sulphides in large layered dunite bodies) of the latest classification of komatiitic nickel sulphide deposits in the Yilgam Block of Western Australia by Hill and Gole (1990).

Jan 1, 1992

By Oswaldo Carhuancho

El presente trabajo señala la filosofía de trabajo en equipo desarrollada en la mina Pierina, Lima. La política de trabajo se sustenta en el pensamiento de Barrick, donde las prácticas administrativas basadas en la seguridad, salud ocupacional y el medio ambiente repercuten en el beneficio de sus empleados, accionistas y las comunidades en las que opera. Por ello, la primera preocupación de la empresa debe ser el trabajador y no las máquinas, así como la labor de los jefes no se limita a una actitud paternalista, sino a una democrática, de forma que el empleado asume sus responsablidades con seguridad y eficiencia. Como consecuencia de ello, se redujeron la cantidad de hombres-accidentess, se elevó el costo de producción y se redujo, la cantidad de personas en la supervisión de operaciones mina.

Sep 13, 2001

By Lei Fu

In the wake of the collapse of the ceiling panels in the I-90 section of the Central Artery/Tunnel (CA/T) Project in 2006, the long term performance of tunnels became the focus of the tunneling industry. At the time of the accident, the tunnel had been open to traffic for about 10 years. This paper will discuss design methods and considerations to improve the long term performance and durability of a tunnel. The major problems found during the inspection of several tunnels will also be presented and the causes for these problems will be discussed.

Jan 1, 2008

By Phillip R. Moyle

A cobalt/manganese occurrence in Clark County, Nevada was the subject of a site-specific mineral investigation by the U.S. Bureau of Mines in 1988-90. The study site is in the northern part of the Million Hills (wilderness) study area which is administered by the Bureau of Land Management. Field work during a period of one week consisted of geological mapping and sampling of workings and outcrops, and geochemical and geophysical surveys conducted on four transects totalling 7,600 ft. Although the concentrations of cobalt (0.1 to 0.5 percent) detected in samples from the fissure zones are within the range of grades associated with world-class economic deposits, the volume of material enriched in cobalt at the study site is insufficient to warrant consideration as a potential resource. Concentrations of manganese, nickel, copper, lead, zinc, barium, and thallium, although anomalous, are too low for economic consideration. At the study site, workings consist of three trenches and nine pits. The exploration history is unknown, and no production is reported.

Jan 1, 1990

By Douglas Talley

This report describes a 4-inch diameter borehole probe which contains a low light level TV camera, magnetic compass, light illumination source, bottom/water detector sensor and a pointing angle sensor. The camera viewing angle is at a right angle to the probe&apos;s body. All data from the sensor is multiplexed into the closed circuit camera video for transmission on a single 50 ohm coaxial cable to a surface control unit. Likewise control of the probe&apos;s power, zoom lens, focus, panning and aperture is accomplished via a down-link multiplexed on the same cable.

Jan 1, 1984

By Jessica Barber

Problem ? Mining operations consistently need equipment that is available, and able to perform to its maximum potential ? The most difficult part of a Maintenance Manager?s job is often a lack of knowledge on how long their equipment has to last ? The short term view can lead to interim fixes that accumulate into larger problems ? It is always difficult to justify major overhauls and upgrades when there is pressure to meet mine plan production targets

May 1, 2008

By Barbara C. Schickner

The long-awaited COSMAR study prepared under the auspices of the National Academy of Science reaches one emphatic conclusion that has been enthusiastically seconded by the mining industry: The 1977 federal surface mining act is "poorly suited" as a vehicle to regulate noncoal mining. Though the industry greeted the report with approval, the weight it will carry and the extent of its impact are yet to be felt. The COSMAR report makes no recommendations-that&apos;s a job left to the Administration&apos;s Council on Environmental Quality-and the prospect of legislation still hovers. For a closer look at the study, MINING ENGINEERING talked to COSMAR committee chairman James Boyd, a well-known presence in the mining arena for over 50 years. After highlighting some of the study&apos;s major points, Dr. Boyd comments on the report&apos;s impact and possible repercussions. Dr. Boyd, for those readers who haven&apos;t seen the COSMAR report, would you summarize some of its major findings? The committee analyzed the surface mining act to determine if it was applicable to noncoal mining and found that there were provisions of the act that either could not be met by existing technology or would be extremely difficult and not necessarily beneficial to adapt. We found that most noncoal mineral mines, despite their obvious diversity, can be considered in two major groups: 93% of all mines move 45% of all materials mined (mostly small units mining construction materials); and the few gigantic regional operations (2%)-copper, iron, phosphate, and uranium mines-that move 50% of the material. With few exceptions, neither of the two groups is amenable to the coal mining practices addressed by the act. The strip mine law was designed for coal mining, where land is regraded, revegetated, and returned to usefulness. In contrast, construction mineral quarries supply local needs for decades, remove most of the material from the immediate vicinity, and cannot be returned to their premining uses (though they have innumerable other valuable uses). The nation&apos;s huge mineral deposits require enormous capital investments, are vital to the nation&apos;s economy, and can take centuries to exploit. Any attempt to return these locations to premining use would be illogical. Pebble phosphate in Florida and red-bed copper in Oklahoma come near to meeting the conditions contemplated in the act. In addition to COSMAR&apos;s basic finding, the study also makes the following points: •Mining uses a relatively small part of the land resource, in contrast to

Jan 4, 1980