Search Documents

By M. A. van Nierop

The Discrete Element Method (DEM) is a model that is used to simulate the motion of the media in a grinding mill. The sum of the energy that is lost in inter-media and media-wall collisions represents the power drawn by the mill. The fact that the DEM predicts the power drawn by grinding mills over a large range of diameters has been used to show the validity of the DEM. However, the power drawn by a mill is a function only of the sum of forces of the load on the shell liners. A more accurate and detailed validation of the DEM would be to measure these forces as a function of angular position as the liner moves under the load, and to compare these measurements with predictions generated using the DEM. An experimental mill has been developed to reproduce exactly what the 2-dimensional DEM simulates. The 0,55 m diameter mill has a length of 0,023 m, which is fractionally larger than the diameter of the media used in the mill. One of the lifters in the mill has been instrumented so that the forces on the lifter can be measured as the mill rotates. The DEM simulation will be used to predict these forces. This will give experimental evidence of the validity of the DEM for modelling load behaviour in rotating grinding mills.

Jan 1, 1999

By Walter O. Snelling

Discussion of the paper of WALTER 0. SNELLING, presented at the San Francisco meeting, September, 1915, and printed in Bulletin No. 100, April, 1915, pp. 695 to 704. A. C. McLAUGHLIN, San Francisco, Cal.-It seems to me that Mr. Snelling's work, if it is what it appears to be, is one of the most important contributions to petroleum technology that has been brought out iii the last 25 years. If his end products are what they seem to be, he has made a discovery, which, in my judgment, will revolutionize the petroleum industry. As to industrially carrying out these processes I do not think there is the slightest difficulty, for I have had some work recently where crude oils were handled successfully at a temperature of 750°F. and pressure of 750 lb. per square inch. WILLIAM A. WILLIAMS, San Francisco, Cal.-What metal did you use, Mr. McLaughlin? - A. C. McLAUGHLIN.-Ordinary seamless tubing, extra strong. WILLIAM A. WILLIAMS.-Tests were made in Dr. Rittman's experimental plant at Pittsburgh, upon samples of residuum furnished by Mr. Bell, the residuum being the remainder of the crude oil after the lighter fractions had been removed. After the material had been run through Dr. Rittman's plant, yields of from 43 to 58 per cent. of material, boiling under 150°C. were obtained. The distillate had a peculiar odor, due to the presence of benzene, toluene, and other unsaturated hydrocarbons. W. N. BEST, New York, N. Y.-What is the difference between the Rittman and the Snelling process or system? WILLIAM A. WILLIAMs.-The fundamental difference is that reactions take place under relatively higher temperatures and pressures and with none of the oil present in its original or liquid state, while the reactions secured by Mr. Snelling and other investigators have been from the liquids in the presence of some vapors. Under such conditions as Mr. Snelling operates, the temperatures and pressures used are limited and the flexibility in the control of these variables is extremely limited when compared with the Rittman process.

Jan 1, 1916

By Stephen A. Swan

This Bureau of Mines report discusses research to analyze and evaluate extended bumper systems in order to determine the degree of protection provided to equipment operators in the event of rear-end collisions be-tween off-road rear-dump haulage trucks. The basic characteristics of rear-end collisions were determined, and a detailed analysis of the col-lision dynamics was performed to identify the magnitude and direction of impact loads, the amount of energy that must be absorbed during impact, and the major factors that affect the outcome of a collision. Separate bumper designs were developed to facilitate attachment to four 170-st-capacity haulage truck frame types.

Jan 1, 1987

East Otago gold deposits are hosted in Otago Schist that is the metamorphosed equivalent of Permian-Triassic Torlesse terrane greywackes. Relatively undeformed Torlesse sequences in Canterbury have <l m - 50 m bedding, with c. 500 m - l km and c. three kilometre scale units, typically either: 1) thick-bedded, massive, sandstones; 2) thin-bedded sandstone-argillite flysch; or 3) siltstone- or argillite-dominated units. Such lithological layering in Otago was intensely folded, deformed, and overprinted by metamorphic fabrics during Jurassic-Cretaceous regional metamorphism. Although primary sedimentary structures can no longer be recognised, a æghostÆ lithological variation is still present in Otago represented by psammitic (sand-derived), interlayered (sandstone-siltstone derived) and pelitic (siltstone-mudstone derived) schist. Lithological æunitsÆ in the schist are typically either 20 100 m or c.1 - 2 km thick, and are oblique to faults and shears hosting gold mineralisation at Macraes, Barewood, Nenthom, and Oturehua. Lithological variations and folds in lithological units are important in the along-strike distribution of gold in these deposits, and in the development of relatively high-grade pods and shoots at l00 m - 1.5 km scales. Ramps, flats and step-overs (known to be locally important for controlling mineralisation) are commonly located at lithological boundaries, presumably by local refraction of faults or shear zones as they propagated through folded stratigraphy. The various lithologies have also responded differently to deformation, causing variations in permeability that affected the penetration of mineralising fluids. Mapping lithological variations in barren host-rocks, either directly+ by fieldwork or indirectly by aerial geophysics, is a key to understanding and predicting the distribution of gold at mine and deposit scales.

Jan 1, 2001

By J. C. Gerdeen

SAP-S information on the following element types are included in this appendix: Type 1. Three-Dimensional Truss and Bolt Element Type 4. Two-Dimensional Finite Elements Type 8. Variable-Number-Nodes Thick Shell and Three-Dimensional Elements Type 9. Two-Dimensional Joint Element (to be used with Type 4 elements) Type 10. Three-Dimensional Joint Element (to be used with Type 8 elements) Additional SAP4 elements, Types 2, 3, 5, 6, 7 and 12, are also contained in SAP-S and information on these elements is readily available in any SAP4 user's manual. These elements are as follows: Type 2. Three-Dimensional Beam Elements Type 3. Plane- Stress Membrane I-r .n Elements Type 5. Three-Dimensional Solid Elements (8 Node: Brick) Type 6. Plate and Shell Elements (Quadrilateral) Type 7. Boundary Elements Type 12. Three-Dimensional Straight or Curved Pipe Elements

Jan 1, 1976

By R. G. Tarr

During an intense and accurate study of initiation systems used on an AngloGold mine, Mine A, poor drilling practices were revealed. Graphic results of all actual measurements taken are shown below. [ ] Accurate drilling of shot holes will determine whether a mining operation is payable or not and at what pay limit mining can take place. Losing 30 cm of a potential 120 cm-hole length will result in a number of consequences, i.e.: ?Higher stoping costs ?Drilling of one shot hole twice in every five shifts ?Increased explosive cost as a result ?Excess stress on hangingwall and footwall due to bad face shape ?Excessive blast damage before the area is worked out. No wonder we have such a high-risk operation. Drilling accuracy is crucial to the profitability on any mine as profits are directly related to the quality and utilization of the drilled shot holes.

Jan 1, 2000

By M. A. Hammer

In this study by the Federal Bureau of Mines Pennsylvania anthracite from the Eastern Middle field was oxidized by concentrated nitric acid at steam-bath temperature for 24 to 1,000 hours. The quantitative data obtained include yields of nitric-acid soluble and insoluble products and the distribution of carbon and ash in each. The acid-insoluble residues were examined for solubility in aqueous sodium hydroxide. With a sodium hydroxide concentration of at least 1 normal, a portion of the residue could be extracted in the form of a true solution. With lower alkali concentrations, peptization occurred. Alkali solubility of the residue increased with length of oxidation. However, when expressed in percentages of original coal weight, the alkali solubility remained essentially constant after 192 hours of oxidation. This suggests that the alkali-soluble products are converted to acid-soluble products at the same rate as the original coal substance is converted to alkali-soluble material. Microscopic observations of the peptization of the acid-insoluble residues revealed a gross micellar physical structure. The action of nitric acid is apparently not restricted to the surface of a coal particle. The acid penetrates the particle through the pore structure, dissolving some of the ash and altering the bonds between the coal micelles. The bond alteration, as indicated by ultimate analyses, involves the physical and chemical adsorption of the components of nitric acid. Some of the altered bonds are not thermally stable; this instability is shown by the complete loss of peptizing ability when the acid-insoluble products are heated above 200° C. This loss is accompanied by the evolution of water, oxides of nitrogen, and hydrocyanic acid.

Jan 1, 1961

By Pierre Gaucher

It is possible to selectively mine an orebody by combining the use of the SSW probe with any bulk mining methods as well as narrow vein exploitations. In other words, thanks to the use of the SSW probe, mining operators will be able to reduce and control dilution that is generally associated to every mining operation. Already, quick and substantial savings have been obtained. Falconbridge mines have demonstrated in Sudbury and Raglan operations, that the SSW probe can log nickel, copper and iron sulphides in blast holes. They have raised the grade and reduced dilution by outlining the limits of the ore zones before selectively loading explosives in the blast holes. By lowering the probe in a blast hole, a profile of the ore content is instantly measured and recorded. Logging cored diamond drill holes at the mine have demonstrated that the ore content (nickel, copper, cobalt, PGM) as assayed is proportional to the intensity of the probe?s electromagnetic response (EM), probably because the nickel / pyrrhotite ratio is uniform within a given orebody. The probe also measures the intrinsic conductivity of the sulphides and the percentage of magnetite. All probe readings are displayed and automatically stored at a 10-cm interval within the same reading unit. A 30-meter blast hole takes less than 2 minutes to survey. The whole instrument is light (12 kg) and very simple to use. One operator can carry the SSW system and survey either down or up-holes. The probe works from ?40°C to +50°C. Plotting the measurements of the SSW probe in blast holes (2-3-4-6-10 inches in diameter) before blasting allows to determine the exact shape of the orebody within the waste rock and uneconomic low-grade ore. Thus, only the portion of the holes that contains ore is blasted. The dilution is then much reduced and, by leaving the waste and low-grade ore in place, the mine saves on transportation, blasting, crushing, backfilling, milling, etc. Thousands of dollars are thus saved. Some savings may also be achieved during the development of stopes by guiding development drifts and by replacing diamond drilling by percussion drilling. In some circumstances, when the probe shows that some of the rich ore was not drilled-off, additional blast holes will allow to recover pockets of rich ore that otherwise would have been abandoned in the walls of a stope.

Oct 1, 2001

By P. Goosen, A. Paterson, E. Paulsen

Ticor South Africa is currently involved in the mining and processing of a heavy mineral oredeposit at Hillendale Mine on the KwaZulu-Natal north coast. The orebody is characterized by a high ultra fine fraction (-45µm) that has a variable rheological behaviour when subjected to shear and hydration. Experience at Hillendale has shown that the ultra fine mineral tailings are sensitive to shear history in terms of shear intensity and shear duration as well as hydration history. This phenomenon expresses itself right through the primary beneficiation process influencing the mineral separation, but is especially prevalent on the residue disposal i.e. slurry transport and deposition on the tailings impoundment. Tube viscometer test work was conducted on the flocculated fine tailings that indicated that there was a change in rheology as a result of shear. This paper presents the results of the on-site test work conducted at the mine to measure the rheology at various stages in the process.

Jan 1, 2003

By D. Mohapatra

The possibility of using 2,2,4-trimethyl-1,3-pentanediol dissolved in tetrachloromethane as extractant for boron recovery is discussed. The parameters optimized for this purpose are contact time, boron concentration in the aqueous phase, extractant concentration, equilibrium pH and phase ratio. NaOH is used as stripping agent for boron recovery from the loaded organic phase. Boron extraction is found to be a slow process (equilibrium time 20 minutes) compared to boron stripping, which is reasonably fast (equilibrium time 5 min). Maximum boron extraction is possible at a broad pH range from 1.0 to 6.0. Using 1.0M extractant concentration, a 1:1 phase ratio (organic: aqueous) and two stages, ~99% boron extraction is achieved. More than 97% boron stripping is possible using 0.5M NaOH at a 1:1 (organic: aqueous) phase ratio in two stages. Overall, a 95.6% boron recovery was achieved. Loss of solvent into the aqueous phase and co-extraction of Ca, Na and K into the organic phase at higher equilibrium pH are two major concerns in his process.

Jan 1, 2008

The Golden Cross mine is situated in a sensitive environmental setting on the North Island of New Zealand, about 150 kilometres south-east of Auckland and about 8 kilometres NW of Waihi. The mine is situated in dipping topography, with volcanic ashes making up soils, fault zones running through the area, and rainfall of about 3 m per year on average. Water management is the most demanding environmental challenge on site, and a comprehensive programme has been put in place to address tailings deposition, long term tailings storage, and water treatment during and after operations.   The tailings impoundment is built with an underdrainage system that collects groundwaters and waters that seep through the impoundment. The embankment and impoundment are both built to withstand the Maximum Credible Earthquake and the Probable Maximum Flood. Tailings are treated to remove cyanide and to decrease metal solubility to reduce long term risk to water quality after mining. A state-of-the-art water treatment plant is utilised to treat water from the underdrainage system and water decanted from the top of the tailings pond and stormwaters to remove residual cyanide and metals to extremely high standards with a great deal of reliability and at reasonable cost. Closure of the facility addresses long term post mining water quality issues, and rehabilitation of the area with wildlife habitat as a priority.

Jan 1, 1995

By Jean Balech

This paper presents some results of dynamic loading tests performed on concrete piles driven in soft clay formation. The load transfer mechanism, measured in the dynamic increasing energy test (DIET), under blows of growing energy, is described in terms of mobilized normal forces diagrams and unitary local friction and displacements. It was observed that the lateral skin friction grows up to a maximum, in the soft clay layer and, gradually diminishes to a residual value when the system presents the maximum mobilized resistance. It may be concluded that the rupture load is not equal to the maximum mobilized point resistance plus the maximum mobilized local friction as suggested by most of static bearing capacity formulae.

Jan 1, 2002

By Eric S. Lindquist

High groundwater levels combined with variable soil and rock profiles present challenges to the design and construction of deep excavation support systems. Increasingly, secant piling techniques are the preferred technical solution for shoring in these cases. Recent developments in drilling equipment, tooling and procedures allow cost-effective construction of deep, overlapped pile systems to tight tolerances in extremely difficult ground conditions. This paper summarizes critical design considerations for secant pile shoring systems, detailing recent advances in installation procedures and verification techniques that allow secant piles to be used for an expanding range of project conditions. Technically- and commercially-viable secant pile shoring designs require that stringent drilling tolerances be achieved in order to successfully provide combined structural support and groundwater cutoff systems, particularly for unreinforced circular secant pile shafts acting in ring compression. Modern drill rigs and tooling can advance fully cased shafts in geotechnical conditions which range from cohesionless soils below the groundwater table to hard rock, within a single drillhole. Down-hole instrumentation provides verification that tolerance requirements are met and allow secant pile shoring to be used at sites previously considered unacceptably risky. In California, secant pile shoring systems are being used for excavation depths of over 100 ft (30 m) on projects with challenging site conditions. Two case studies are presented detailing severe geotechnical conditions and excavation depths which represent the regional state of practice in secant piled excavation support. These projects provide real world examples of the design, construction and construction verification techniques that permit secant pile shoring to be used in more demanding geotechnical conditions and to greater depths than ever before.

Jan 1, 2011

By Bryan A. Bartley

"Jim Macdonald was promoted from Waterworks Engineer to Streetworks Engineer for the Wellington City Council. He thus took over the City quarry and responsibility for its performance. The crushing plant needed upgrading and he thought it would not be difficult to make a crusher to overcome a problem. If he had a longer association with the quarry industry he would have used conventional methods and equipment, so his invention arose from a fresh view of crushing.He invented the Barmac Rotopactor after observing a wear resistant chute with a lining of dead stone trapped above a piece of angle. This idea led to a rotor lined with trapped stone, rotating on a vertical spindle. In trying - a model rotor he observed the impact against a circular rill of stone in half an oil drum and thus was started a very fertile new area of developement in comminution. The writer helped in the developement and shares in the patents. Jim died in January 1982, just as the machine was becoming known and some 200 were in use in various countries. Most were working in hard rock quarries et that time but recent uses have carried the machine into the mining and mineral processing field. This paper is directed at that industry."

Jan 1, 1985

By I. D. Nock, R. M. Parkin

Paper presented at a meeting on: Artificial intelligence in the minerals sector, held in Nottingham, UK, 20 April 1993 (original title: Knowledge-based condition monitoring of cone crushers). A large proportion of the electricity used by the quarrying industry is consumed in the comminution and sizing process. In most cases aggregate processing plants operate with minimum control features resulting in limited operational efficiency. Improved control is required to increase operational efficiency with concomitant savings associated with reduction in re-circulating load and improved resource utilisation. Development work has suggested that a combination of adaptive control and process condition monitoring could improve control of comminution plants. Many commercial process control and condition monitoring systems are available, but none were deemed suitable due to the domain specific characteristics of the application. An assessment of the particular characteristics of cone crushing concluded that the application was best suited to the use of small domain specific process control combined with bespoke condition monitoring. The processing power of the control system for the project is a function not of the academic requirement, but rather the economic and practical constraints imposed by the application. As a result of the constraints a high-end PC system has been designed in preference to a workstation. Within the research project work packages are sub-divided into novel wear sensor development, knowledge based control/condition monitoring and the investigation and mathematical modelling of the wear mechanisms inherent in cone crushing. Numerous strategies were considered to implement the control system outlined. The system currently under development is a modular design which utilises intelligent novel sensors to provide a variety of data inputs

Apr 1, 1994

By I. R. Ward

"The need for energy conservation has been of increasing concern since the early 1970's, when the cost of petroleum based energy began to escalate rapidly and security of supply became uncertain. The cost of energy from alternative sources has also increased due to development costs and environmental restrictions.These developments have had a serious impact on the mining industry, which is energy intensive. The impact is magnified as lower grade ores are treated, and more energy is consumed per unit of product. In many cases increased operating cost is not compensated by the rise in product selling price.The magnitude of energy consumption in the mining industry is indicated by recent studies conducted in the U.S.A. and Canada. Based on 1970 figures, it was reported that the production of 1 ton of copper in the U.S.A. required 111. 8 x 106 BTU of energy, of which 60. 7 x 106 BTU (54.3%) was consumed in mining and processing (l)The survey of Canadian mills, conducted by CANMET and reported to the CMP meeting of 1978 (2), showed the following milling energy consumption figures (approximate averages):"

Jan 1, 1981

By Natasha A. Essar

Nevsun Resources Ltd. Bisha Mine Project is a gold and base metal development project in the Gash Barka region of west-central Eritrea. The project has the potential to be one of the largest industrial developments in the country, and Eritreans have no experience in modern mining. Nevsun recognized early that the success of the Bisha Project would require meaningful consultation and engagement with all levels of Eritrean society. Meaningful engagement required not only full disclosure, but also capacity building from government officials at all levels to other stakeholders who live in the nearby communities. This paper describes the approach used to develop capacity and to help introduce a modern mining culture in a country without previous experience in mining.

May 1, 2007

By R. L. F. Kay, T. A. Fletcher, A. J. Boyce, C. M. Rice

Paper presented at Mineralisation in the Caledonides, the Mike Gallagher memorial meeting held in Edinburgh, 27-28 June 1996. The synorogenic, mafic Ordovician intrusion comprises orthopyroxene-rich xenoliths and mafic-ultramafic cumulates with low-grade pyrrhotite, chalcopyrite and pentlandite mineralisation. Despite abundant textural, mineralogical and O isotope evidence for significant assimilation of country rocks, S isotopes indicate only a modest uptake and suggest that mineralisation is dominated by magmatic sulphur. The preferred explanantion is that the magma was close to S saturation on emplacement. Uptake of elements such as Si and O led to early crystallisation of orthopyroxene, resorption of olivine and early segregation of a sulphide liquid. Post-magmatic interaction with a high-temperature, surface-derived fluid, whose movement may have been controlled by regional shear zones, reset biotite and whole-rock O isotope values but not those of orthopyroxene. This model identifies the presence of olivine-rich rocks and evidence of extensive assimilation as guides to prospectivity

Jun 19, 1905

By K. Ding

The thermodynamic activity of MnO was measured in MnO-CaO-MgO-SiO2 slags that are typically encountered in the production of manganese-containing stainless steels. A gas equilibration-quenching technique was employed in measuring the activities. Activities of Mn in Pt-Mn alloys were redetermined at 1600ºC, which reconfirmed earlier results of strong negative deviations. MnO activities were then measured by equilibrating slags of various compositions based on a statistical experimental design procedure with Pt-Mn alloys under controlled partial pressure of oxygen in MnO saturated platinum crucibles at 1600ºC. Activities of MnO were found to increase with increasing concentration of MnO, basicity and CaO to MgO ratio. Two multi-coefficient regression models were developed to predict the activities and activity coefficients of MnO in slags at 1600ºC. Keywords: activity, MnO, slag

Jan 1, 2005

By Jean-François Lessard

The performance of rock pass systems has a significant contribution to the economics of underground mines. Operational concerns include hang-ups due to arching of material, blockage and degradation of the rock pass. This papers presents the preliminary results of a comprehensive rock pass database on the engineering and operation of rock pass systems in Quebec underground mines.

May 1, 2002