Search Documents

This paper discusses support requirements for the proposed monorail system to be used in decline development. The monorail drilling and loading systems are systems that move on the rail (monorail) installed in the roof of the decline and supported by roof bolts, suspension chains and steel supports. However, due to the weight of the components of the two systems, it is imperative that the force in each roof bolt, suspension chain and steel support capable of suspending the weight of the heaviest component is determined. Numerical models that relate the weight of the monorail drilling and loading components to the required strength in the support system have been developed. Using these developed models, numerical values of the forces in each roof bolt, suspension chain and steel support, required to suspend the weight of the heaviest component of the monorail drilling and loading systems are determined.

Dec 6, 2010

By K. A. Lewandowski

The efficiency of heap leaching is reduced by poor solution flow characteristics (i.e., channeling and ponding) that result from fines migration. Agglomeration of the ore can immobilize fines, but for agglomeration to be successful in copper leaching, an acid-resistant binder is needed to stabilize the agglomerates. Until now, there has not been a satisfactory method to evaluate whether a binder was effective, other than squeezing a handful to see if it ?feels right.? This paper reports on several procedures that have been developed to quantitatively determine whether a binder gives good performance in an acidic solution. These procedures have been used to identify binders that would be suitable for copper heap leaching.

Jan 1, 2008

By A. J. Partos

One Liberty Place, at 315 m is the tallest building in Philadelphia, PA USA. It is supported on drilled piers socketed in heterogeneous rock. 3832 kN/m2 end bearing and 383 to 766 kN/m2 shaft resistances were selected. Design load distribution was 40% on the base and 60% by shaft resistance. The maximum compression on the corner core columns is supported by clusters of 3 drilled piers. In order to confirm load distributions along shaft and at the base, Drilled Pier G-10 supporting T13-A type outrigger column was instrumented. This column supports 53,849 kN compressive load which includes 13,440 kN windload. This paper reveals details about the process to select the final design for One Liberty Place together with pertinent Information about site geology, foundation construction, quality control, and methods of steel erection. It also presents detailed Information on the type of Instruments, their calibrations, field fabrication, and installation in the shaft of Pier G-10. Readings of concrete temperatures, computed loads, and load distributions are presented for a period from October 1985 through May 1988. The building was completed in 1987.

Jan 1, 1989

By Julius Roth

Flyrock is the source of most of the injuries and property damage in a majority of blasting accidents in surface mines. A quantitative correlation between shot conditions and maximum flyrock range can be used to define a "blasting area" in which no personnel or equipment should be present during a shot. The approach used was to develop a model that correlates shot conditions and initial flyrock velocities and permits computation of flyrock range from ballistic trajectories. The Gurney formula for velocity of explosively-propelled plates or fragments was adapted to explosively-propelled flyrock from vertical rock faces or from bench tops. The modified Gurney formula was then "calibrated" with measured flyrock velocities from mining and explosives literature. Charts were then developed for possible field use which give maximum flyrock range as function of shot conditions. The model indicates that for flyrock from vertical faces, borehole diameter, minimum burden and height of explosive column define maximum flyrock range for a given explosive, shot in a given rock. For flyrock originating from bench tops, flyrock range appears to be controlled by the distance of the top of the explosive column to the borehole collar, by total explosive load per borehole and, to a lesser extent, by borehole diameter.

Jan 1, 1979

By N. E. Hanna

The current list of permissible explosives includes 124 different brands. Fifteen of these are gelatinous, and the rest are the more commonly used granular ammonium nitrate type. Their rates of detonation range from 1,300 to 5,600 meters per second, and the weights of 1-1/4 x 8-inch cartridges range from 86 to 244 grams. The list of permissible blasting devices includes 1 Cobra, 2 Hydrox, and 9 Cardox models. All of these devices are based on discharge of high-pressure gas from a pressurized shell in a shothole. INTRODUCTION To be approved for use in underground coal mines in the United States, explosives and blasting devices must pass certain schedule tests prescribed by the Bureau of Mines. The explosives listed here were tested under Schedule 1-G,3 which has since been replaced by Schedule 1-H;4 the blasting devices were tested under Schedule 26A.5

Jan 1, 1962

By A. Martikainen

Field tests concerning a fog mesh method for fog removal are discussed. The first tests were performed at the Pyhäsalmi Mine, Finland. As this study gave promising results, further studies were completed at the Orivesi Mine. The results of these most recent field tests are presented and the two studies are compared. The Orivesi test set consisted of four materials. These included air filter fabric, fibrous filter fabric, a plastic greenhouse mesh, and an aluminium mosquito net. The variation of the Orivesi results was more noticeable than what was found previously. The best fog removal effect of all tests was achieved with the aluminium mosquito net, while the plastic green-house mesh performed worst. The humidity reduction by aluminium net was more profound than any of its precedents. More mesh materials will be tested in the near future.

Jan 1, 2007

A New Cell for Electrochemically Aided Flotation

Sep 13, 2010

By J Lyall Workman, Peter N. Calder

"Large hole rotary drilling is one of the most common methods of producing blastholes in open pitmining. Large hole drilling generally refers to diameters from 9 to 17 inch (229 to 432 mm), however aconsiderable amount of rotary drilling is done in diameters from. 6% to 9 inch (165 to 229 mm). Thesesmaller diameters are especially prevalent in gold mining and quarrying."

Jan 1, 1996

By E Topal

Stopes are used in several underground mining methods. Boundary determination of these stopes is generally based on simple rules of thumb. While several stope boundary optimisation techniques are available, they fail to guarantee true optimum results. The first part of this paper reviews some important stope boundary optimisation studies and proposes a new algorithm to optimise stope boundaries and layouts for underground operations. The second part applies the proposed algorithm to a block model to test its ability to produce optimum results and demonstrate its applicability in a number of different scenarios. The results demonstrate that the proposed algorithm can find optimum stope boundaries and layouts in three dimensions for different stope sizes and economic conditions.

Jan 1, 2009

By D. W. Nel

Nanofiltration (NF) has attracted much attention over the past few years due to the reduced energy consumption compared to reverse osmosis (RO) and better separation performance compared to ultrafiltration (UF). Although research has been done in the area of NF of nickel ions, sodium ions, and acid separation, not much attention has been given to the separation of high nickel concen¬trations from sulphuric acid streams. The use of NF for the separation of nickel and acid from a spent nickel electrolyte is an innovative process alternative for future industrial application within a base metal refinery. In this study, the separation performance of a composite polyamide NF membrane on a spent nickel electrolyte was investigated by varying the sodium sulphate concentration in the feed (50-150 g/l), the trans-membrane pressure (35-55 bar), and cross-flow velocity (1.5-3.5 m/s), and measuring quantities such as total permeate flux, acid rejection, nickel rejection, and sodium rejection. The nickel and acid concentration in the feed were kept constant with variations between 40-60 g/l and 25-40 g/l respectively, while the temperature of the experiments was kept constant at 50°C. The membrane was found to be very selective for nickel ions, with the rejection of nickel ions varying between 54.4% and 98.2%. The rejection of acid ions varied between -5.9% and 21.8%. The rejection of sodium ions varied between 16.6% and 72.4% at a cross-flow velocity of 2.5 m/s and sodium sulphate concentration of 50 g/l in the feed solution. An increase in trans-membrane pressure increased the rejection of nickel, sodium, and acid ions, while an increase in sodium sulphate concentration decreased the rejection of nickel and acid ions. The total permeate flux was found to increase with an increase in trans-membrane pressure and decrease with an increase in sodium sulphate concentration. The cross-flow velocity had an insignificant effect on the total permeate flux and the rejection of nickel, sodium and acid ions.

Jan 1, 2013

By Walter D. Holland

This instructors guide is intended for use in a course which teaches metal and non-metal mine inspectors to perform surveys for inhalation contaminants in above ground metal and nonmetal mine work areas. The handbook entitled "Handbook for Surveys of Inhalation Contaminants in Above Ground Metal and Nonmetal Mining and Processing Work Areas? is used as a manual during the course. The manual contains a survey check list, rules for determining if sampling is required, a list of most frequently encountered contaminants, a list of candidate contaminants and their sampling conditions, and a description of control procedures and devices. There are several experiments in this guidebook which the trainees perform to acquaint them with the sampling systems.

Jan 1, 2011

By S. P. Singh

The purpose of the cut is to provide a free face to which the remainder of a development or breasting round can break. The results of field testing in drifts and at a quarry face were used as a basis for a description of the rock breakage and flushing mechanism in the cut. It was concluded that the important features of a cut design are proper hole spacing, sufficient relief volume, drilling accuracy and relief holes slightly longer than the planned length of the round. The void space provided by the relief holes should be about 15% of the cut volume, with more required in weak, highly fissured rocks. The importance of drilling accuracy increases with round length, an error being magnified by the small blasthole spacing. The first hole pulls only about 20% of the round length, 4-6 holes having to be fired before the cut is pulled close to its design depth. The first four blastholes should be fired with a minimum inter-hole delay of 100 ms to provide progressive relief of burden and avoid the superimposition of ground vibrations. The earliest-firing charge should be closest to the relief area and act laterally, while the first of the vertically-fired charges to be detonated should be the uppermost. Problems during cut-pulling include sympathetic detonation, dynamic pressure desensitisation, charge disruption and freezing of the cut

Dec 1, 1995

By W. L. Falke

This Bureau of Mines report illustrates critical path planning and scheduling techniques as applied to typical mining operations. Detailed examples of arrow diagramming and computer oriented applications of critical path methods are given. Program Evaluation and Review Technique (PERT) is discussed briefly in comparison to the Critical Path Method (CPM).

Jan 1, 1966

By G. Kim

The influence of bacterial growth phase on the flotation behavior of malachite has been investigated in a well-controlled Hallimond tube system. The microflotation tests were conducted for malachite (45?53 µm) using different amounts (bulk phase concentration=1×108?5×109 cells/mL) of Rhodococcus opacus (R. opacus) as a collector, which was grown at mid-exponential versus stationary phase, at a constant speed (340 rpm), pH (6), and malachite-bacteria interaction and flotation time (each 10 min). Hug differences between R. opacus cells in mid-exponential and stationary phase was observed from the results for electrophoretic mobility and flotation tests. Specifically, the isoelectric point of the cells in the stationary phase was lower than that in the mid-exponential phase, suggesting that the amount and distribution of surface functional groups onto cell surfaces are likely different. Additionally, the cells in stationary phase led to significant increase in the flotability compared to those in mid-exponential phase over the background bacterial concentration level of 1×108?5×109 cells/mL. Furthermore, the flotation efficiency tended to increase with increasing cell dosage for stationary phase cells while no distinct difference was observed for mid-exponential cells.

Feb 27, 2013

By D. A. Wilson

A cyclic leaching process was developed for selectively leaching and recovering cadmium from nickel-cadmium scrap battery waste. The six major steps in the process are the following: (1) washing the plates to remove KOH electrolyte, (2) roasting at 550° to 600° C to oxidize metallic cadmium and decompose cadmium and nickel salts, (3) leaching with an ammonium nitrate solution, (4) precipitation of the leached cadmium from solution as cadmium carbonate using CO2 gas, (5) removal of CO2 from the lixiviator by adjusting to pH 4.5, heating, and evacuating the system, and (6) removal of small amounts of leached nickel from the lixiviator using a solvent extraction technique. The regenerated lixiviator is then recycled to leach additional plates. Cadmium extraction was 94 percent and the cadmium carbonate product contained 0.14 percent nickel and 0.12 percent cobalt impurity. The leached plates were smelted to a high nickel-low iron alloy with no detectable amounts of cadmium.

Jan 1, 1971

By H. Stanley Benson

This report is an account of research conducted to improve the performance of and then further field test Draft Power Sensor (DPS) equipment, the use of which enables a bulldozer operator to optimize his machine's work rate. Significant improvements were made in DPS hardware, and extended field testing was conducted at two working strip mines: the Glenharold Mine of Consolidation Coal Company, near Stanton, North Dakota, and the Beulah Mine of Knife River Coal Company, near Beulah, North Dakota. This report documents the increase of bulldozer work production by greater than twenty percent while using the Draft Power Sensor when compared to baseline work production without benefit of the Draft Power Sensor. Research was done by Southwest Research Institute under contract with the Bureau of Mines.

Jan 1, 1980

By J. Werfling, J. R. Kiehl

SUMMARY: The effects of blasting on structures are assessed on the basis of the maximum amplitudes of the occuring vibration velocities. If the standard values in the German Standard DIN 4150 are not exceeded, damages to structures are not to be expected. The estimation of the maximum vibration amplitudes is usually based on experience or on emperical formulae. However, a comparison of expected with measured values shows that these estimations are not conservative, particulary in case of small distances between blasting locations and structures. More reliable predictions are possible on the basis of numerical analyses, which simulate the three-dimensional propagation of waves with consideration of the geomechanical and geometrical conditions. In addition to the expected velocities, these analyses also allow the determination of stresses resulting from dynamic loading. If the dynamic stresses are known, the effects of blasting on structures can be predicted. ZUSAMMENFASSUNG: Die Auswirkungen sprengbedingter Erschütterungen auf bauliche Anlagen werden in der Praxis auf der Grundlage der Maximalamplituden der auftretenden Schwinggeschwindigkeiten beurteilt. In der DIN 4150 werden Anhaltswerte angegeben, bei deren Einhaltung Schäden von Gebäuden nicht zu erwarten sind. Die Abschätzung dieser Schwing-geschwindigkeiten erfolgt meist auf der Grundlage von Erfahrungswerten oder empirischer Formeln. Der Vergleich der prognostizierten Werte mit Meßergebnissen zeigt jedoch, daß diese Ansätze insbesondere dann, wenn die Abstände zwischen den Sprengorten und den Gebäuden gering sind, nicht konservativ sind. Zuverlässigere Prognosen sind auf der Grundlage von numerischen Berechnungen möglich, in denen die räumliche Ausbreitung von Erschütterungen unter Berücksichtigung der geomechanischen und geometrischen Verhältnisse simuliert wird. Mit derartigen Berechnungen können die zu erwartenden Schwinggeschwindigkeiten und die aus der dynamischen Beanspruchung resultierenden Spannungen ermittelt werden. Dies ermöglicht Aussagen über die Auswirkungen sprengbedingter Erschütterungen auf Bauwerke. RÉSUMÉ: Les conséquences de vibrations résultantes d'explosions pour des bâtiments sont estimés dans la pratique à partir des amplitudes maximales des vitesses d'oscillation. Dans la norme allemande DIN 4150 des valeurs d'orientation sont données, avec l'observation desquelles de dommage à des bâtiments n'est pas à présumer. Ces vitesses d'oscillation sont estimés généralement à partir de valeurs d'expérience ou de formules empiriques. La comparaison des valeurs prédits avec des résultats de mesures montre cependant que ces hypothèses ne sont pas conservateurs, en particulier si les distances entre les lieux de sautage et les bâtiments sont petites. Des prédictions plus fiables sont possibles à partir de calculs numériques, dans lesquelles la dissipation spatiale de vibrations est simulée en considération de la situation géoméchanique et géométrique. Avec tels calculs les vitesses de vibration à présumer et les contraintes résultantes de l'effort dynamique peuvent être établies. Cela permet de constater sur les conséquences de vibrations résultantes d'explosions pour des bâtiments.

Jan 1, 2003

By T. T. Campbell

This investigation was undertaken by the Bureau of Mines to determine if high-purity ductile molybdenum of uniform quality can be prepared by bomb reduction techniques. Molybdenum trioxide (Mo03) and mixtures of molybdenum dioxide (Mo02) and trioxide were reduced by magnesium in closed steel bomb reactors. Very high pressures in excess of 5,000 p.s.i. developed during magnesium reductions of Mo03. The addition of calcium oxide to the bomb charges caused a significant reduction in pressure. Reaction efficiencies higher than 95 percent were obtained during magnesium reductions of either Mo03 or mixtures of Mo02 and Mo03, but high pressures were encountered when the charges contained from 30 to 60 percent Mo02. Reaction efficiencies were usually low (less than 80 percent) when the bomb charges contained more than 40 percent Mo02. The charges with the best composition considering operating pressure, yield, and purity contained from 10 to 30 percent Mo02. The addition of small amounts of carbon to the reaction charges was helpful because some deoxidation occurred during the reduction and also during subsequent arc-melting of the regulus metal. The purity of the bomb-reduced, arc-cast molybdenum metal ranged from 99.2 to 99.8 percent and in some instances the metal contained as little as 5 parts per million oxygen.

Jan 1, 1962

By Emad Farouz

The resistance of very dense glacial outwash formations consisting of sand, gravel and cobble formations can be quite high, and techniques for measuring the strength and deformation properties often cause engineers to underestimate the strength of these layers in drilled shaft design. More realistic measurements of this dense formation can be achieved with slotted steel casing pressuremeter tests. To minimize disturbance and achieve accurate measurements, drilling a pilot hole prior to probe insertion is necessary. Characterizing geologic formations that contain significant amounts of gravel and cobbles is challenging because of scale factor. Inserting a standard pressuremeter probe into this formation without damaging the membrane is difficult. This paper presents a case study for the IR-75 project in Dayton, Ohio, USA, where these dense materials were characterized using a slotted casing pressuremeter, optimizing design by providing more realistic properties of these materials.

Jan 1, 2006

By R. Webber-Youngman

The Department of Mining Engineering at the University of Pretoria accepts that the process of teaching and learning improvement is an ongoing exercise with the ultimate aim to deliver well-rounded mining engineering practitioners. Various challenges impact on the success of this process. An integrated and innovative process was developed and is followed in the Department to overcome these challenges. The aim of the Department is to apply a holistic teaching approach by introducing multiple integrated interventions with regards to teaching and learning strategies. Three phases of this process are discussed in this article, and are illustrated in Figure 1. During the first phase, prior to 1999, several teaching and learning challenges were identified in the Department of Mining Engineering. These challenges are discussed in the next section. In the current phase, a variety of interventions to address the challenges are being developed, implemented (in some cases piloted), and evaluated. The future phases will focus on the improvement, successes, and full roll-out of current interventions, as well as on training, development, and support for all staff members to participate in the process. (Figure 1)

Jan 1, 2011