Search Documents

As a part of its overall wealth in fuel resources, the United States possesses large reserves of coal of ignite rank. According to recent estimates of the Federal Geological Survey (3, 5),l/ the assured lignite reserves of this country amount in total to over 463 billion tons, equivalent to 24 percent of our total national coal reserve on a tonnage basis and 15 percent on a heating-value basis. Distribution and relative amounts of United States coal and lignite reserves are indicated in figure 1. By far the largest proportion of our lignite reserves, over 95 percent is found in North Central States, principally in North Dakota, South Dakota, and Montana, in the vast coal-bearing structural grouping designated as the Fort Union formation. Of the remaining United States reserves, all but a fraction of 1 percent are found in a series of relatively scattered deposits in Texas.

Jan 1, 1954

The use of scrapers in mining and earthmoving operations is not new, in fact they are one of the earliest methods of bulk earthmoving. A single machine which can load, haul, and dump material with a minimum of ancilliary support is a highly productive and cost-efficient method of earthmoving. In recent times scrapers have been unpopular due to perceived problems and operational limitations, but the last couple of years have seen a resurgence in the use of scrapers in the Bowen Basin as a primary prestripping tool. The main operational limitation of scrapers is the economic operating range. maximum productivity and lowest cost per bcm is achieved on short leads, as the lead distance increases the cost per bcm quickly reaches and then overtakes that of an truck-excavator fleet. The geometry of a ætraditionalÆ coal mine does not readily allow short leads for prestrip fleets due to the nature of dragline stripping operations. The strip arrangement means that material has to be taken around the end of the pit, meaning a longer haul distance than the actual point-to-point distance between load and dump. This can be alleviated by using pit bridges, however these can cause spoil problems for draglines if not properly planned and have been avoided by many mines. Due to the economic haul distance limitation of scrapers, truck-excavator fleets have become the normal method utilised. Currently more geologically complex mines are opening up, which do not allow traditional down-dip strip mining to occur. Cross-dip mining methods allow for short leads between prestrip loading and dumping areas, hence scrapers and bulk doze are realistic alternatives to a truck-excavator fleet in the prestrip environment. Keeping the lead distance to a minimum a fleet of 657Æs can move material at a very low cost. The other main operational limitation of scrapers is the type of material that can be economically excavated. Hard material can lead to damage to the bowl, free-flowing sand will not readily stay in the bowl leading to reduced load factors. Ripping the material with a dozer prior to excavating can lead to improved loading time, and greatly reduced GET consumption. When considering scrapers for prestrip operations a number of things must be considered: is the lead distance within the economic haul distance? should twin power (push-pull) or single power (dozer pushed) scrapers be used? do I need to rip, what should I rip with? what ancilliary support is required? is there another system already available on-site which is currently under utilised? This paper considers the parameters under which large twin power scrapers are the most effective way of undertaking prestrip operations.

Jan 1, 2003

By E. R. Palowitch

Two samples of the Lower Hartshorne (Spadra) bed were collected: A sample of the raw coal with the machine cuttings excluded, and a sample of the machine cuttings exclusively. Analysis of the 5-inch by 200-mesh size fraction of the raw coal, excluding machine cuttings, showed that a product meeting minimum quality specifications could be produced by washing at 1.60 specific gravity, yielding a theoretical 93.7 percent of clean coal. A negligible amount of near-gravity material at the separation gravity indicated an easy washing problem. The sample of machine cuttings had a maximum size of 2 inches and contained about 50 percent ash. Washability tests of the 2-inch by 200-mesh size fraction indicated that a theoretical yield of 30.0 percent of specification-grade coal could be achieved by washing at 1.49 specific gravity. As the machine cuttings represent an estimated 10 percent of the total coal mined, their inclusion in the mine output would increase the theoretical net yield of salable coal by only 3.7 percent. Because the machine cuttings contained a high percentage of sink 1.80 specific-gravity material, they had neither an effect on the separating gravity required to clean the raw coal nor on the difficulty of separation. Gabbing underground versus transporting the cut-tings to the surface for disposal or washing either separately or combined with the raw coal involves a number of practical, economic; and intangible factors; hence, no specific recommendations could be made. A discussion of some of the factors involved in dealing with a similar problem is given by Gandrud and Riley.4

Jan 1, 1962

By D. P. R. Smyth

The limestone reef reservoir at Swan Hills consists essentially of a "buildup" of successively smaller atoll-like layers. Precipitation of calcium carbonate within the lagoonal area of each layer essentially kept pace with growth of the outer organic lattice. Within the reef mass, six de-positional environments characterized by specific suites of fossils (or fossil fragments) and associated limestone textures are recognized as follows: ( 1) Aerated moderately agitated water of normal marine salinity (widespread shelf or submerged reef-built platform). Thamnopora-type corals, Amphipora, "pancake" stroma-toporoids, crinoids, articulate bra-chiopods, rare rugose cup corals, and ostracods occurs in light gray-buff skeletal microgranular limestone of low permeability. (2) Semi-stagnant quiet water of normal marine salinity (leeward side of reef). Crinoids, articulate brachio-pods, rare thamnopora-type corals, Amphipora, pancake and bulbous stromatoporoids, rugose cup corals, ostracods and gastropods occur in impermeable dark brown argillaceous skeletal calcilutite with thin black bituminous shale beds and rare dark chert nodules.

Jan 1, 1961

By T. G. Joseph

Mines must manage variability from within their operations as well as those imposed upon them by external forces. This paper provides a framework to manage both internal and external variability through the review and adjustment of the mine plan where applicable to minimize lost production and maintain operational safety.

Nov 1, 2011

The National Mining Hall of Fame will hold its 13thAnnual Induction Banquet during MINExpo International 2000 in Las Vegas, NV. The gala black-tie (optional) event will honor eight legendary leaders of the mining industry. The event will take place at the Las Vegas Hilton Hotel on Sunday, Oct. 8. The induction ceremonies will salute mining greats elected by the board of governors from a list of nominees submitted by mining industry partners and the public. The members of the Class of 2000 will join 151 other inductees enshrined in the Mining Hall of Fame in Leadville, CO. The evening will begin at 6 pm with a cash bar reception followed by the banquet and program at 7 pm. Keynoting the banquet program will be Harrison (Jack) Schmitt. He was the geologist/astronaut of the Apollo 17 mission to the moon in 1972 (see related story on page 26). And he is the only scientist to “kick rocks on the moon.” Schmitt is also a member of the Mining Hall’s board of governors. Schmitt was also the keynote speaker at the First Annual Induction Banquet in Denver, CO in 1988.

Jan 1, 2000

By T. C. Woo

This report describes the program that studied the theoretical and practical aspects of the belt cleaning systems, investigated-the possibilities of a self-replacing and/or sell-adjusting belt cleaning device, and designed a horizonal pentagonal turret setup for the underground mine belt conveyors. This design resulted from comprehensive literature survey (both academic and commercial), actual mine visits, study of the mechanics of belt cleaning and bench-type experiments. It has complete working drawings and rough cost estimates.

Jan 1, 1977

By Ronald W. Stingelin

The geology of the roof of the Pittsburgh coal bed was studied and mapped in nine contiguous counties containing the bulk of the remaining reserves of this coal bed in the northern Appalachian Coal Basin. Drill core records from Belmont and Monroe counties, Ohio, Washington and Greene counties Pennsylvania, and Ohio, Marshall, Wetzel, Monongalia, and Marion counties, West Virginia provided the data for twelve computer generated regional geologic variable maps. Four of these geologic variables (overburden thickness, vertical distance to the rider coal, lithology at the five foot horizon above the roof of the mineable Pittsburgh seam, and the number of lithologic changes within the 30 foot interval above the roof of the mineable Pittsburgh seam) were used to estimate the risk of potential roof falls by a methological scheme developed during this study. A hazard zone risk map was developed showing a generalized regional trend of increasing risk from west to east across the basin. Mapping of individual geologic variables and mapping of hazard risk can be done at any scale. The accuracy of the mapping is primarily dependent on the density of the drill core records. Geologic feature maps and the hazard risk map contained in this report are reduced (1 :500,000 scale) versions of the larger scale (1 :62,500) maps prepared for the Bureau of Mines as map folios.

Jan 1, 1979

By Aleksandar D. Bugarski

Despite extensive research efforts conducted in the past decades, occupational health risks associated with exposure to nano and ultrafine aerosols emitted by diesel power equipment are still not completely understood. The complexity of physical and chemical properties of diesel aerosols, constantly changing with the implementation of advanced diesel emissions control technologies, make this task rather challenging. The objective of this paper is to identify and characterize nanometer and ultrafine aerosols emitted by diesel engines in the underground environment and evaluate the effects of selected contemporary control technologies on physical properties, chemical composition, and in-vitro toxicology of diesel aerosols. The physical and chemical properties of the nanometer and ultrafine diesel aerosols are to be characterized through a test series in the NIOSH Lake Lynn Laboratory experimental mine. The crucial part of the study has been development of a facility that allows researchers to generate field results with precision and accuracy characteristics of a laboratory environment. The knowledge obtained from this study should strengthen our understanding of the health implications related to exposure to diesel particulate matter and aid in assessing the potential of various control technologies for reducing this exposure.

May 1, 2007

By Marie-Pierre Bourdouxhe-Barnich

Since 1997, in partnership with the Laboratoire Central des Ponts et Chaussées in Strasbourg, ProfilARBED has been carrying out a vast study to qualify the improvements jetting can make to vibratory driving of steel sheet piles, and to understand its effect on the surrounding ground and on the sheet piles themselves. The process basically involves discharging a fluid (mostly water, sometimes in association with air) at controlled pressure and/or flow rate near the toe of the sheet pile being driven. The steel jetting pipes are attached to the sheet pile and are connected to the pumps by hoses. The jet of fluid loosens the soil, thus reducing the resistance at the toe of the sheet pile. Depending on ground conditions, the fluid that flows along the pile can reduce skin friction. Four soil types were involved in our experiments. Each site was instrumented: the driving parameters and the geotechnical characteristics of the soil before and after vibratory driving and jetting-assisted driving were recorded. Each test provided its own particular information which contributes to overall thinking on the matter and is of help to project managers who are often confronted with rapid driving to the final depth.

Jan 1, 2002

By D. P. Penswick

The Palabora open pit is scheduled to cease operations in 2002. While the ore body continues below the bottom of the final pit shell, the stripping ratio precludes further economic open pit mining. Palabora Mining Company has investigated various means of continuing copper production, and has determined that an underground mine is the best solution. Board approval to commence construction of the mine has been granted and shaft sinking is underway. First production is planned for the year 2000 and full production of 30 000 t/d will be achieved by the end of the year 2002. [ ] Mechanised block caving will be the mining method employed at Palabora. The cave will be initiated by excavating a thin horizontal slice known as the undercut. Removal of the undercut will induce stresses which cause the rockmass overhead to fracture. Fractured rock will gravitate through drawbells to drawpoints on the production level, and be loaded by LHDs for transport to crushers.

Jan 1, 1997

By J. H. Kim

Since the Hardy Cross numerical algorithm was applied to the solution of mine ventilation networks, there have been numerous developments in ventilation network analysis procedures. The Newton-Raphson method, the linear theory method, and the second-order approximation method are three of the additional approaches that have been applied. The efficiency of a ventilation network analysis procedure depends not only on the method of solving the system of equations derived from ventilation networks, but also on the method of deriving the equations through selection of the meshes. This paper investigates the impacts of three mesh selection methods on the efficiencies of four ventilation network procedures. The minimum-resistance spanning tree method is the most popular procedure for selecting meshes. The shortest-path method was suggested by Epp and Fowler (1970) for improvement of the Newton-Raphson method. The minimum-resistance-path method is suggested here as the third method of selecting meshes. The effects of these three methods on the Hardy Cross method, the Newton-Raphson method, the linear theory method, and the second-order approximation method are analyzed in this paper. These network analysis methods have been summarized in the paper by Kim and Mutmansky (1991).

Jan 1, 1992

The growth of "Unit Load-cargo handling technology in world cargo lin- er trades over the last decade has cre- ated a situation in which special pur- pose-vessels (cellular container ships, roll-on/roll-off vehicle deck ships and Lash type vessels) are rapidly replac- ing conventional cargo ships, the principal means previously available for transporting heavy lifts. Consequently heavy lift traffic has tended to accumulate awaiting ship- ment, especially where discharge is required in "off beat" locations. A partial solution to this problem will be provided by new and small but exceptionally versatile ocean going heavy lift carriers now finding their way into world trade routes. These new ships combine extremely high lifting capacity, high manoeuvreability and exceptionally shallow draft with bow and stern Ro/Ro capability. They can handle rolling loads of exceptional size and weighing up to 1,000 tons Each. But the problem is a far larger and more serious but essentially a domestic one. Major industrial pro- jects in Australia will require pro- gressively heavier and larger plant and construction sites are becoming much more inaccessible. Whereas these new ocean going heavy lift carriers have ample capacity to satisfy part of the total transport requirement, there is clear evidence to show that domestic transport resources have little if any potential for increase in capability at the same rate as demand or at the same rate as sea transport facilities. Resolution of the larger problem is within reach but only through a pro- perly co-ordinated approach to future planning for the overall needs of large scale projects on a national basis. This co-ordinated approach must involve Federal and State government transport administrators, railway and highway authorities, shipping and road haulage interests and finally the planners of the projects which require these improved heavy haulage services.

Jan 1, 1973

By Cathleen J. Webb, Arden D. Davis

The Homestake Gold Mine at Lead, South Dakota, has been proposed as the host site for the Deep Underground Science and Engineering Laboratory. The laboratory will house neutrino experiments in mine workings at the 7400-foot depth, as well as research in geomicrobiology, rock mechanics, and ground-water flow. Initial plans for the laboratory were developed in 2000 after Homestake Mining Company announced the closing of the underground gold mine. Homestake’s owner, Barrick Gold Corporation, had agreed to donate the mine for a laboratory if it could be protected from environmental liability. That initial agreement was delayed, and Barrick turned off the mine’s pumps in 2003, allowing lower levels of workings to begin to flood with water. In early 2004, the Governor of South Dakota signed an agreement with Barrick that would indemnify the company and eventually transfer ownership of the mine to a state laboratory authority. South Dakota’s governor also announced plans to ask the state legislature for funds to help in the initial construction of the laboratory. A consortium of scientists from several states is currently preparing a detailed laboratory proposal for the National Science Foundation.

Jan 1, 2005

By Doss H. White

Alabama's non fuel mineral industry produced $560.6 million of mineral commodities in 1990. This was an increase of $99 million over the 1989 value and a new State record, a record achieved despite the slowdown in the national economy. This was the first year that Alabama's mineral value exceeded one-half of 1 billion dollars. The value of stone and cement, the two leading mineral commodities in terms of sales, increased $71 million over that reported for 1989 and was the primary reason for the new mineral value record. The State ranked 21st among the 50 States in total mineral value and contributed 1.68% of the total U.S. mineral value of $33.3 billion.

Jan 1, 1992

By R. Ordóñez Olivares

This manuscript focuses on the design and development of steels for the railroad industry and methods of testing them. Here are summarized the results of research focusing on alloy development and design, with particular focus on advanced rails and wheels. The high-performance steels are characterized for their mechanical and service characteristics. The relationship between properties and cleanliness is discussed and compared to the regular railroad steel. Some of the tests presented are standard tests that are complemented with the nonstandard test recommended by the Association of American Railroads (AAR) and recommended modifications of this. The paper presents the results of metallurgical analysis, mechanical, and residual stress tests. The laboratory methods include microstructure, residual stresses, tensile, hardness, fracture toughness, and microcleanliness tests.

Jan 1, 2013

By Louis Schaffer

This report characterizes several coal Dine mobile equipment operator populations with respect to age, mine experience, machine operator experience, and training. The information is used to demonstrate a method of normalizing the injury data collected by the Mining Enforcement and Safety Administration-Health and Safety Analysis Center.

Jan 1, 1977

By John V. Simmons, Peter J. Simpson

Excavated slopes in open pit coal mines are designed to be as steep as possible consistent with stability and safety requirements. Slope failures occur for many reasons, including oversteepening. This paper is concerned with slope design and excavation experience in the Bowen Basin coalfields of central Queensland (Figure 1), [ ]

Jan 1, 2006

By George T. Faust

The petrographer engaged in examining the products resulting from the beneficiation of ores and rock minerals is constantly required to develop new means and methods of assaying microscopically the results of such operations. From time to time investigators have published descriptions of apparatus that have aided in solving problems in processes f physical separation. Thus, in 191.9, Coghill and Bonardi 31 published a paper covering the application of the binocular microscope and camera lucida to the microscopic analysis of pulverized ores. Similar work has been published by Schneiderhohn 4/, Schwartz 5/, and Head and his associates6/, 7/, 8/. The present paper goes further and considers application of the polarizing comparison-microscope to problems directly concerned with mineral dressing where it is desirable to compare analogous products, and in addition it suggests new uses in various related fields. This work was conducted under the cooperative agreements of the Southern Experiment Station of the Federal Bureau of Mines and. the University of Alabama.

Jan 1, 1940

By Shaw Bill

The paper describes of the JORC Code in terms its background working environment and reasons for success, and provides references to papers which cover the subject in more detail. It then discusses the two major developments in Australasian reporting standards in the last two years: the revision of the 1999 Code, and the introduction in early 2003 of the “ROPO” (Recognised Overseas Professional Organisation) initiative. The purpose of the JORC Code is to provide a minimum standard for reporting of Exploration Results, Mineral Resources and Ore Reserves in Australasia, and to ensure that public reports on these matters contain all the information which investors and their advisers would reasonably require for the purpose of making a balanced judgement regarding the results and estimates being reported.

Apr 22, 2003