Search Documents

By S. H. Lorain

Mechanized dirt-moving equipment has greatly increased the scope of prospect trenching by lowering the costs and increasing the speed of such work. Where the soil covering was more than 3 or 4 feet deep, operators were quickly discouraged and abandoned surface exploration in favor of shaft sinking, drifting, or diamond drilling; wildcat trenching was seldom undertaken, even where the soil covering was thin. Although power shovels, trench diggers, and draglines are useful under special conditions, caterpillar-mounted angledozers will usually do the same type of work and have a far wider range of adaptability. They are therefore incomparably the most generally useful equipment for the purpose. Since 199 the Bureau of Mines has been engaged in a widespread search for minerals useful to the war program; this work required a great deal of pioneer exploration in areas where known outcrops were marginal or subcommercial by pre-war standards. Engineers in charge of field operations were quick to perceive the applicability of mechanized trenching on a fairly large scale, particularly in the Northwestern States, where completely exposed vein-outcrops are rare. Probably no other organization to date has done a comparable amount of angledozer prospect trenching under such a wide range of conditions. The following comments and accompanying cost tables are based on work performed chiefly in Idaho, under a variety of physical and climatic conditions. The most important applications of the angledozer for such work may be described under three heads:

Jan 1, 1944

By Bernard Baum

Combined preservative/fire retardant systems were pressure impregnated into Douglas fir and Ponderosa pine samples and evaluated for decay, flammability, and mechanical properties. The objective of the evaluation was to identify cost-effective systems for use with mine timber, and to provide an information and data base from which Federal code regulations could be established. Thirty systems, based on combinations of commercially available preservatives and fire retardant impregnants and coatings, were applied to Douglas fir samples and evaluated for decay and flammability. The ten most promising systems were ap¬plied to both fir and pine and reevaluated for decay and flammability before and after water leaching. The five best systems were given a thorough laboratory evaluation using both pine and fir. Evaluations included flame spread, smoke density, toxic gases, decay, compressive strength, flammability after artificial weathering, and cost. All systems had acceptable toxic gas levels and smoke densities, but flame spread was only borderline acceptable for most of the samples tested. A trade-off analysis showed Acid Copper Chromate/Fyrprufe with Albi-107A/144 intumescent paint and Koppers NCX to be the-best systems. Recommendations are made for further large-scale testing using the two best Systems.

Jan 1, 1978

By C. A. Jeffrey

The Dirtlow Rake vein deposit, which is up to 12 m thick, contains a range of paragenetically linked replacement mineralisation styles typical of many Mississippi Valley-type deposit environments. The main ore zone lies within the solution collapse breccia domes, the more southerly of which has recently been well exposed, allowing its relationship to the associated mineral-hosting structures to be studied. The domes were largely formed during early silicification, propagated by dissolution collapse and infilled by subsequent fluorite-barite mineralisation. The location of pipes and pervasive replacement was also controlled by early silicification. Structurally controlled bow tie shears were formed as a result of fluid access at fracture-bedding plane intersections. The nature and distribution of the mineralisation styles indicate that the degree of fluid access, residence time of solutions in contact with the wallrock and susceptibility of the limestone to silicification each played a major role in dictating mineralisation

Jun 19, 1905

By Pastsakom Kitiyodom

In order to estimate the deformation and load distribution of a single pile subjected to dynamic horizontal load as well as vertical load, a simplified method of three-dimensional numerical analysis, KWaveHybrid program, is developed using a hybrid model. In the hybrid model, the pile is modelled as elastic beams, and the soil at each pile node is treated as springs and dashpots in both vertical and horizontal directions. KWaveHybrid is also able to analyse the static response of the pile. Validity of the newly developed program is examined through comparisons with theoretical values and horizontal dynamic and static pile load test results

Jan 1, 2006

In 2005, a total of 739 nonmetal mining operations reported employment to the Mine Safety and Health Administration (MSHA). These mines (e.g., potash, gypsum, salt) comprised 5.0% of all operations. ? Mines producing common clay comprised 26.9% (n=199) of all nonmetal mining operations. ? Nonmetal mining operations were located in all states and territories except Alaska, Delaware, Hawaii, Maine, New Hampshire, Rhode Island, Puerto Rico, and the Virgin Islands.

Jan 1, 2008

By J Aydin Bilgin, Sedat Esen

This paper describes the ideality of some commercial explosives with the help of the detonation theory and detonation velocity measurement. Ideality of an explosive can be determined by comparing experimentally measured and ideal detonation velocities. A measured detonation velocity at a certain charge diameter markedly lower than the ideal value indicates incomplete reaction and thus non-ideal detonation. Since it is shown that commercial explosives exhibit non-ideal behavior, two-dimensional detonation theory should be used to evaluate the performance of explosives. This theory enables to compute the detonation properties of explosives (detonation velocity, detonation pressure, etc.) as a function of charge diameter and confinement. The use of the one-dimensional detonation theory to compute the detonation properties for commercial explosives has an error associated with it as these calculated properties are independent of charge diameter and confinement. It assumes that shock front is planar. Hence, it is incapable of assessing the ideality of the explosives due to its assumptions. Shock front in real situation is curved in shape but not planar as in one-dimensional detonation theory. In this paper, the non-ideal behavior of some commercial explosives is modeled using EXRINT code based on the steady-state two-dimensional detonation theory firstly. Then the degree of ideality of each explosive found from the code is checked using detonation velocity test results conducted at a quarry. It has been shown that idealities of the tested explosives determined by the code agree well with the field detonation velocity test results.

Jan 1, 1999

By Rajib K. Mohapatra, K. Vizaya Kumar

In any manufacturing organization internal logistics plays a vital role in improving and maintaining the productivity. In Ferro Alloys manufacturing organization where there is huge input of raw material in terms of ore, reductants and variety of fluxes amounting to about four times of the mass of alloy produced need to be handled from yard to furnaces , internal logistics requires utmost attention. Any deviation or mismatch between stock and requirement will affect furnace operation. Though the activities are being outsourced by most of the organization, these require close monitoring. This communication presents an optimization model which can work as a ready reference for the manager to decide upon the material quantity and the furnace to be fed with an objective of minimizing the cost of handling and zero production loss.

Jan 1, 2007

A shortage of technical skills in all areas of the mining industry is being experienced worldwide. This has significant consequences for design, operations, productivity and safety and, therefore, needs to be seriously addressed, both in the short and longer term. It is therefore both a strategic and a tactical issue. Importantly, however, since mining is a long-term business, the shortage of skills must be dealt with from a strategic point of view to ensure the supply of the necessary skills for future mining. This paper will deal specifically with the provision of high level technical skills, that is, university graduates in mining engineering, and the outlook for the institutions that are currently producing such graduates.

Jan 1, 2009

By Thomas O. Meyer

Laboratory test results are presented for the determination of elastic modulus made with the NX borehole jack. Determinations were made in massive pieces of aluminum so as to satisfy conditions of linear elasticity, homogeneity, and isotropy. Results indicate a large discrepancy (approximately 200 percent) betwen material modulus as determined by laboratory block-loading tests and that indicated by the jack under relatively ideal circumstances. Effects due to interface friction, finite block size, incomplete plate-bore contact, and other factors were examined and found not to be significant. Finite element results indicate that assumed loading conditions for the jack differ from those actually occurring, at least in materials of high elastic modulus (approximately 10 million psi), such as quartzite.

Jan 1, 1974

By C. P. Mangelsdorf

Introduction The use of frequency of vibration measurements to determine tension has long been accepted by industries that use electrical or stranded cables of wire ropes in their operations. In contemplating how to determine the tension in chords of a roof truss, it seems almost inevitable that a similar approach should be investigated even though there are some important dissimilarities in physical behavior between a chord of a rod-type Birmingham truss and a stretched wire rope. While the dominant feature of both types of behavior is the existence of tension, the bending resistance of the vibrating truss chord cannot be ignored. And it is common to have attached to the chord, pieces of hardware (turnbuckles, extension sleeves, wedge boxes) that represent concentrations of mass not usually found in a vibrating wire rope. Analytical solutions to the problem of vibrating wires or beams can be found in the literature on vibrations (Timoshensko, 1955; Den Hartog, 1956). But in every case, at least one of the ingredients of the vibrating truss chord is missing. The presence of axial tension, or bending resistance, of concentrated masses and of end conditions peculiar to truss chords is a combination that appears not to have been dealt with before, although the techniques for dealing with it are commonly known. The purpose of this note is to report the results of a project to measure and calibrate such frequencies. The work was conducted by the University of Pittsburgh under the sponsorship of the US Bureau of Mines. Field observations Tests were conducted on 24 different truss installations. The first 18 trusses were installed in shale roofs above Kentucky No. 9 seam and Illinois No. 6 seam. The remaining six were placed against the competent sandstone over the Pocahontas No. 3 seam in West Virginia. Chord tension was determined by two electrical resistance strain gages, in series, applied diametrically opposite to one another on the rod before tensioning. Due to the combined effects of inexact gage placement, rod bending and residual torsion in the chord due to tightening, errors in tension as high as 1780 N (400 lb) were reasonably possible. Due to faulty soldering or damage, three of the first 18 trusses and one of the final six were rendered completely unreliable. In addition to strain, the first natural frequency of vibration was observed to the nearest 0.1 Hz. Dimensions recorded included the span between contact points at the bearing blocks (Fig. 1) and the locations and amount of excess rod and rod gap at the wedge box and turnbuckle, respectively.

Jan 9, 1985

By H. G. Wolfhard

The propagation of explosions through short cylindrical channels has been investigated by the Bureau of Mines. In the experimental apparatus set up by the Bureau, a single such channel formed a connection between a small explosion vessel in which a gaseous explosion was initiated and a larger, partly enclosing, explosion vessel filled with suitable gaseous mixtures; the larger vessel permitted observation to determine if an explosion was induced therein by mass, energy, and species transfer through the channel, as a result of tie initial explosion, It has been found that transmission of flame through to channel is not an essential to induce the second explosion, for hot gases from an extinguished explosion are able to ignite cold combustible mixtures in the larger vessel. The schlieren patterns of flames or hot burned gases emerging from a channel into the explosion chamber were photographed. These show, in most instances, that vortexes of hot gas ejected from the jet into the cold explosive mixture are responsible for ignition. The study has practical significance in problems of rendering electrical equipment safe for use in potentially flammable atmospheres, INTRODUCTION The propagation of flames through cylindrical or annular channels has practical importance in flameproofing electrical equipment and for flame traps. Much practical work has been done to determine the minimum safe breadth of flanges and the maximum safe gap between the flanges that will permit venting an electric motor without allowing flames to pass.

Jan 1, 1959

By Aldino Campos, Frederico Carvalho Dias, Pedro Madureira, Patrícia Conceição, José Gomes-Pereira, Inês Tojeira, Andreia Afonso, António Calado, Luísa Pinto Ribeiro

Since 2008, the Portuguese Task Group for the Extension of the Continental Shelf has been operating the ROV "Luso" (rated for 6000m depth) for geological sampling of the deep North Atlantic seabed, performing surveys on, e.g., seamounts and hydrothermal vent fields. Amongst other sensors, the ROV is equipped with a full HD video camera with which still images of the deep ocean floor are recorded. Fixed on the ROV’s frame are two underwater "line" lasers, each generating a sharp green line (532nm) over the seabed. The two lasers are paralleled and calibrated at a set distance. Provided that the camera’s angle of view is known, numerical values for seabed surface area may be calculated using direct measurements taken from the pictures containing the laser lines. We present the corresponding main mathematical formulas, which are derived from simple geometrical considerations, and discuss how to generalize these results for an arbitrary camera tilt or pan. We present an example of application of our method by estimating values for percent coverage of rock substrate versus sediment. Our results are also relevant for determining seabed polymetallic nodule abundances from still images obtained during ROV surveys.

Sep 1, 2014

By J. C. Schneider, G. Van Weert

Hydrochem Developments Ltd. has developed and put into full scale operation a novel type of vertical flotation column incorporating a multiplicity of mechanically agitated stages. Characteristics of this flotation column include a low height to diameter ratio, high upgrading factors and the possibility of modifying geometry and operation to specific flotation requirements. A commercial unit is currently handling up to 100 tpd rougher concentrate at Dickenson Mines Limited, Balmertown, Ontario. Design parameters and plant performance will be discussed.

Jan 1, 1988

By Andrew Pontecorvo

The design of foundations for the tall buildings of lower Manhattan rely on the use of high capacity, rock anchors to resist overturning forces generated by lateral loads from wind, earth, water and, to a lesser degree, seismic forces. Once completed, the proposed towers at the World Trade Center (WTC) site will be among the tallest buildings in New York City. The towers are exposed to coastal winds and from several levels of below grade structure soil and water loads. The design loading required under the current New York City Building Code (NYCBC) is similar to the requirements of the building code used to design the original WTC Twin Towers. We will compare how rock anchors were deployed in the Twin Towers and how they are used in the new buildings. Changes to the building code are less significant that the changes to the design of the structure; that is how the outer skin or perimeter structure interacts with the building core. The result is a significant increase in the number of rock anchors required for the new buildings when compared to those installed in the original WTC Twin Towers.

Jan 1, 2011

"Blasthole deviation is a frequent, well documented and undesirable occurrence in mining operations. It is caused by the drill string mechanics, operating variables and the 'interactionbetween the drill bit and the rock mass characteristics. It is composed of three distinct components: collaring or marking error, alignment error and trajectory deviation. This study has focussedon the dependence of trajectory or natural deviation on the geological features of the rock mass being drilled."

Jan 1, 1996

By J. B. Seymour

This paper provides an overview of the current use of backfill for ground support in underground metal mines in the United States and a summary of recent accident data reported for these mines by the Mine Safety and Health Administration (MSHA). Backfill mines comprise a major part of the underground metal mining industry and are particularly important in terms of the fatalities and injuries impacting this workforce. Ground falls are the leading cause of fatal accidents at these mines accounting for 50 percent of the total fatalities (4 out of the 8 fatalities that occurred from 2006 through second quarter of 2011). MSHA reported several different types of accidents involving backfill at these mines. While backfill ground falls do not occur frequently, these accidents result in a much higher proportion of fatalities than host rock ground falls. Backfill ground fall accidents are especially hazardous in underhand cut-and-fill mining operations where employees work directly beneath the backfill. An analysis of recent MSHA accident data supports the need for further cooperative research with the mining industry to identify and address ground control problems in underground metal mines using backfill.

Feb 27, 2013

By B. C. Qi

"In water treatment, flocculation or coagulation with aluminium or ferric salts has been widely used for many years to remove natural organic matter (NOM), including humic acids. However, the adsorption of NOM to aluminium hydroxide flocs during conventional coagulation/flocculation processes is very complex, with the flocculation of aluminium hydroxide particles and the adsorption of NOM molecules on flocs occurring simultaneously. Any effect on the surface characteristics and micro-structures of the humic acids and aluminium hydroxides could affect the adsorption efficiency.It has been widely observed that if a reaction system (liquid-liquid or liquid-solid) is exposed to an ultrasound field, under appropriate conditions, a variety of physical (emulsification, aggregation/flocculation) or chemical (the production of radical and exited species; single electrotransfer) actions may be activated. Though the ultrasound effects have been used in biological and chemical decontamination in many conventional environmental protection practices, the idea to explore the ultrasound effects in the removal of humic acids by preformed aluminium hydroxide flocs is relatively new. In this paper, the effect of an in-situ ultrasonication on removal of the humic acids extracted from the acidification fermentation of lignocellulosic residues, by a preformed aluminium hydroxide, was evaluated; the effect of ultrasonication on the surface complexation of the humic acids with the preformed aluminium hydroxides was investigated."

Jan 1, 2003

By Leandro Echavarría

El presente texto describe el sistema epitermal de Arcata, situado en Arequipa, Perú. Arcata es un distrito epitermal de sulfuración intermedia rico en plata y metales base, cuya mineralización se hospeda en vetas de rumbo predominante noroeste y movimiento principal paralelo a la inclinación que forman una estructura de fosa (graben). Las vetas poseen texturas de relleno de espacios abiertos como bandeados costriformes, en cucarda, crecimientos en peine y brechas, con ganga de cuarzo, calcita, rodonita y rodocrosita. Por su parte, los minerales de mena más comunes son galena, esfalerita, calcopirita, con los metales preciosos hospedados en sulfosales de plata (pirargirita y tetrahedrita). Asimismo, se ha identificado una compleja secuencia paragenética con varios pulsos responsables de la mineralización económica.

Apr 22, 2003

By Sami Makni, Ahmed Bouajila

"To remain competitive in an open market, mining companies are more and more requested to optimise their complex and highly multivariate processes. The increasing amount of process data, brought about by intensive use of instrumentation and the progress in computer data acquisition, enhances the need for more and more powerful and robust tools for the analysis and modelling of the process data. Now, with the emergence of multivariate data analysis (MDA) techniques, on-line clustering of mineral process behaviour is possible and could help in the extraction of valuable process operation indicators. MDA can be used in different mineral processes such as flotation, grinding, smelting etc. In this paper, the focus will be on grinding process as it is the one of the most costly node in the mineral processing scheme (i.e. power consuming) and it is a highly multivariable process. Particularly for primary grinding mills (SAG/AG), more instrumentation outputs and more powerful and significant process indicators are needed for efficient control and optimisation.MDA is a novel approach suitable for understanding mineral process behaviour compared to the traditionally approaches based on empirical and phenomenological modelling. Multivariate techniques can be used for several purposes. In this paper, the following objectives will be addressed:operation diagnosis: Shift differentiation and operation test differentiation can be showed by using MDA tools such as principle component analysis and factorial discriminant analysis.operation performance monitoring: operation regimes can be evaluated by clustering based on an economic criterion performance such as costs, tonnage, product quality, profit, etcIdentification of operation behaviour (monitoring) and selection of drift correction trajectories (control):MDA can be used to identify periods of unusual or abnormal process behaviour and to diagnose, if it is possible, causes for such behavior."

Jan 1, 2003

By N. Krauland, A. Nystrom, M. Board, S. Sandstrom

Several deep Swedish cut-and-fill mines experience severe ground control problems, including roof collapse and wall sloughing, as a result of variable rock quality and high in situ stresses. A project to examine the problem included two main areas. The first was prediction of mining conditions at depth and the adaptation of cut-and-fill mining to such conditions; the second was the assessment and improvement of support methods at present and future depths. Simple, elastic, mine-scale numerical models were used to optimise stope sequencing and more detailed, stope-scale models to simulate the failure processes around a stope and the interaction of rock mass and support. Kristineberg was chosen for testing and calibration of the predictive methods because of its long history of severe ground conditions and the large base of observational and monitoring data available for comparison. Horizontal cut and fill was found technically suitable to depths beyond 1 000 m and economically viable if ore value covers support costs. Stability can be achieved with the present support technology down to 1 000 m but the 7-strand 15.2 mm cables have poor deformation properties (5% failure strain) compared with rebar rock bolts (17%). Reducing the intervals between levels from 100 m to 50 m will cut support costs and improve production reliability and capacity. Simulation of sill-pillar mining indicated that conditions would be most severe when pillar height was reduced to 15-20 m; mining of a sill pillar has been carried out successfully to the last 3 m, whose extraction is planned for the near future

Dec 1, 1995