Search Documents

By G Mark, K L. Blake, G de Jong, J F. Rotherham, N D. Adshead

Magnetite deposits with distinctive ¦ actinolite ¦ apatite-bearing gangue and spatially-extensive sodic-calcic wall rock alteration occur in both Proterozoic metamorphic terrains and Mesozoic-Tertiary magmatic arcs. Examples from both settings constitute significant sources of iron ore (egKiruna, Sweden; El Romeral, Chile) and some host major Cu-Au deposits that have a local association with K-silicate alteration (eg Cloncurry district, NW Queensland; Copiapo district, Chile). A growing body of evidence points to a hydrothermal origin for these systems involving high temperature, low S oxidised fluids. The Cloncurry magnetite-Cu-Au deposits are products of the local structurally channelised influx of a specialised high salinity ore fluid into larger-scale alteration systems developed during pluton emplacement at greater depths than those associated with subvolcanic (porphyry) Cu-Au deposits. The geological characteristics of deposits in magmatic arcs are consistent with a similar mode of origin albeit in rather different tectonic settings.

Jan 1, 1995

By G. R. Smith

Critical and strategic metals are often present in small quantities in low-grade domestic ores. When these ores are leached, the resulting solution usually contains the metals in very dilute quantities. Selective electrowinning from dilute electrolytes was investigated by the Bureau of Mines. A metal deposit containing 84 pct nickel was electrowon from the leach solution of a complex domestic ore bulk flotation concentrate originally containing approximately 2 wt-pct nickel. Key to achieving accelerated deposition rates, in the case of dilute solutions, is the rapid movement of the electrolyte through the electrowinning cell. Pure, synthetic nickel electrolytes were used to establish deposition parameters, and to optimize electrolyte velocity or mass transfer rates. Hydrodynamic and electrodeposition parameters for both the synthetic and leach electrolytes are presented and the experimental research described. Selective electrowinning appears to offer a viable alternative to physical separation methods to obtain separate metal "concentrates" from low-grade ores.

Jan 1, 1983

By Ali Porbaha

The use of soil nailing technology as a cost effective alternative for excavation support and slope stabilization has substantially increased in the United States during the last decade. For example, in the past thirteen years, more than 185,800 square meters of soil nail walls have been constructed in California alone. The conventional soil nail systems pose difficulties when ground conditions are subject to caving, for instance for silty sand (sugar sand) or cobbles and boulders. The construction industry has developed self drilling hollow bar systems (or pressure injected bored, IBO) that combine both drilling, placing and grouting in a single operation as a solution to speed up construction. While the system is extensively used for temporary applications, nevertheless, some concerns, particularly about corrosion, has limited the use of this technology as a permanent system in North America. This study presents several issues related to self drilling soil nail systems, the results of a field investigation and a summary of the research project.

Jan 1, 2006

By Augustine O. Orumwense

Ball mills are commonly used for regrinding operations in the mineral processing industry. But, in recent times, efforts are being made at the introduction of stirred mills particularly for those instances where very fine grinding is required. Media type (steel shot, glass beads, alumina balls and crushed quartz), media size, mill speed and the number of passes required to obtained the target product size are studied. The product size and energy consumption are used in the evaluation of the test results. The grinding media size, shape, density, filling ratio, mill circumferential speed and grinding time play a distinct role in product size fineness.

Jan 1, 2005

By S. Nagamatsu

Alumina supported gold catalyst prepared by spray reaction method (spr) provides gold particle with about 20 nm of diameter. The gold particle size is larger than conventional gold catalysts. However, the spr catalyst shows higher catalytic activity for NO-CO reaction. In the present paper, we have discussed the local structures of spr-Au/Al2O3 catalyst by using Au L3-edge XANES spectra. In order to investigate the local structures of Au-sites, multiple scattering approach to XANES analysis was applied. Calculated Au L3-edge XANES spectra for fcc-Au and Au2O3 were in good agreement with the observed spectra. XANES spectra for spr-Au/Al2O3 were characterized by 4 types of Au sites (bulk, interface, surface and peripheral). In this case, almost all gold sites (> 90 %) are bulk site. The other sites are less than 10 % of gold particle. However, the experimental and the calculated results of Au L3-edge XANES spectra for spr-Au/Al2O3 require about 30 % of gold oxide or hydroxide. Bulk of Al2O3 contains a certain number of gold nano-particles, which was incorporated in the bulk Al2O3 support. In the interface area, gold oxide forms a few layers. This result was also supported by DV-Xa electronic structure calculations. The comparison of the catalytic activities of the spray catalysts and the impregnation catalyst for the NO-CO reactions imply synergy effects between gold nano-particles and alumina support.

Oct 1, 2003

By Thierry Bernard, Jean Marc Laboz

This paper explains why and how integration of EIS (Electronic Initiation System) with dedicated software tools can increase benefits to blasters and at the same time simplify the design of blast sequence

Jan 1, 2000

By S. Jiansheng, H. Nakayama, D. Lu, A. Wang

ABSTRACT: New techniques and methods for 3D geo-mechanical model test are presented in this paper. The new model material NIOS with high density and low cost; the so-called DPSS (Discrete Principal Stress Surface) loading concept, the loading and monitoring system for the generation of the 3D initial stress field of the model test, also the special techniques and apparatuses for modelling the excavation of caverns located deep inside the model material, are developed and introduced. By adopting those new techniques, a very large 3D geo-mechanical model test with high comparability for a newly designed underground powerhouse has been successfully fulfilled. Key Words: 3D model test, underground group caverns, excavation process modeling. ZUSAMMENFASSUNG: Neue Techniken und Methoden für 3D geomechanischen Modellversuch wurden in diesem Artikel vorgestellt. Ein neues Modellmaterial mit hocher Dichte und niedrigem Preis, ein sogenanntes DPSS (Discrete principal stress surface) Ladenkonzept, ein Laden- und Überwachungssystem für die Erzeugung des 3D primären Spannungsfelds und überdies spezielle Techniken und Maschinen für das Ausbruch der tief in dem Versuchsmodell liegenden Kaverne wurden entwickelt. Bei Anwendungen dieser neuen entwickelten Techniken wurde ein sehr großer 3D Modellversuch mit großem Maßstab für ein geplantes unterirdisches Kraftwerk erfolgreich durchgeführt. Stichworte: 3D Modellversuch, unterirdischen Gruppekaverne, Ausbruchsmodellierung Résumé: le test de modèl de Nouvelles techniques et méthodes pour la géo-mécanique 3D est figuré dans ce papier. Le nouveau modèle de matériels NIOS avec la haute densité et le coût bas; la conception proposée de chargement DPSS (Discrete Principal Stress Surface), le système de chargement et de moniteur pour la génération de champs de stress initial du test de modèle, ainsi que les techniques et appareils spéciaux pour modeler les excavations de cavernes profondément localisées dans l’intérieur du matériel de modèle, sont développés et introduits. A travers l’adoptation de ces nouveaux techniques, le test de modèle de la géo-mécanique très large 3D avec la haute comparabilité pour actualiser une nouvelle étude de la centrale électrique sous-terraine a déjà accompli avec succès. Mots de clé: test de modèle 3D, groupes de cavernes sous-terraines, processus de modèle d’excavation

Jan 1, 2003

By Han-Tao Hu

Keywords: RH refining process, flow of molten steel, two-phase flow, gas holdup, circulation rate, mathematical modeling A three-dimensional mathematical model for the flow of the molten steel in the whole degasser during the RH refining process has been proposed and developed with considering the physical characteristics of the process, particularly the behaviors of gas-liquid two-phase flow in the up-snorkel and the momentum exchange between the two phases. The fluid flow fields and the gas holdups of liquid phases and others respectively in a 90 t RH degasser and its water model unit with a 1/5 linear scale have been computed using this model. The results showed that the flow pattern of molten steel in the whole RH degasser could be well modeled by the model. The liquid can be fully mixed during the refining process except the area close to the free surface of liquid and zone between the two snorkels in the ladle, but there is a boundary layer between the descending liquid stream from the down-snorkel and its surrounding liquid, which is a typical liquid-liquid two phase flow, and the molten steel in the ladle is not in a perfect mixing state. The lifting gas blown is rising mostly near the up-snorkel wall, which is more obvious under the conditions of a practical RH degasser, and the flow pattern of the bubbles and liquid in the up-snorkel is closer to an annular flow. The calculated circulation rates for the model unit at different lifting gas rates are in good agreement with the determined values.

Jan 1, 2005

By Carl W. Lam

The increased obsolescence rate of electronic products has made it evermore pertinent to understand the potential environmental impact of materials choices to help guide electronic waste (e-waste) management and promote awareness of high burden materials. Methods for screening for the performance of materials and their potential burden on human health and the environment can be used to comparatively select constituents of present and prospective electronic products. These methods should be able to yield more robust information when linked to other decision-making strategies where integrated data on consumer preferences, production quantities, and regulatory initiatives are sparse or unavailable. A framework is presented here for generating metrics of ecological toxicity, human health toxicity (cancer and non-cancer categories) and global resource consumption for evaluating environmental impact of materials (specifically metals) in electronic products. The time-dependent impact trends of United States? printed wiring board (PWB) metals usage, principally derive

Jan 1, 2010

A paper presenting an overview of legislative and best practice approaches to the management of OHS&E and business risk for Australian tunnelling operations. Best practice can be achieved in Australian tunnelling through ærisk awarenessÆ by decision-makers and line personnel. This will identify problems before they occur and lead to implementing controls appropriate to avoiding loss throughout the life cycle of the underground opening. The author draws on legislative approaches from all Australian states together with practical experience from risk management and risk engineering work from six recent tunnelling projects. This describes a process that:commences with concept risk assessment,involves quantification of major hazards,conducts assessments of operating risks, andleads to implementation of an integrated management system that keeps construction activities connected with the controls identified in the design and planning phases and minimises the losses sustained as a result. Key points addressed include:where the industry is going with respect to risk û methods and considerations,how tunnelling risks are perceived by the industry and legislation,how tunnel constructors and owners can minimise exposure by using proper risk engineering ætoolsÆ, andreflections on best practice methods for transferring knowledge from designers to contractors/operators.

Jan 1, 2008

By J. C. Ashby

Electric utility response to certain amendments of the Clean Air Act has resulted in a production of several types of alkaline coal combustion byproducts. Alkaline combustion byproducts are gaining increased usage for acid mine drainage mitigation and abatement as research leads to a better understanding of their beneficial applications. Since January of 1997, Mettiki Coal Corporation has been injecting alkaline flue gas desulphurization byproducts from Virginia Electric?s Mt. Storm Unit #3 wet limestone scrubber into abandoned portions of the active Mettiki mine. This paper provides an overview of the key design, transportation, regulatory, and environmental issues faced in the project.

Jan 1, 1999

By P. H. S. W. Kulatilake, B. Malama

To simulate brittle rocks, a mixture of glastone, sand and water was used as a model material. Thin galvanized sheets were used to create joints in blocks made out of the model material. To investigate the failure modes and strength, both the intact material blocks as well as jointed model material blocks of size 35.6 × 17.8 × 2.5 cm having different joint geometry configurations were subjected to uniaxial and biaxial compressive loadings. Results obtained from the intact model material blocks are used to validate a new intact rock failure criterion for biaxial loading. Results obtained from both the intact and jointed model material blocks are used to develop a strongly non-linear new rock mass failure criterion for biaxial loading. In this failure criterion, the fracture tensor component is used to incorporate the directional effect of fracture geometry system on jointed block strength. The failure criterion shows the important role the intermediate principal stress plays on rock mass strength. Zur Simulation spröder Gesteinsarten wurde ein Modellmaterial aus Dentalgips, Sand und Wasser hergestellt. Daraus wurden Blöcke gegossen, in denen mittels dünnen, galvanisierten Blechen Trennflächen erzeugt wurden. Die Blöcke mit Abmessungen von 35.6 × 17.8 × 2.5 cm wurden in einaxialen und biaxialen Druckversuchen belastet. Es wurde das Versagensverhalten und die Festigkeit von intakten Blöcken sowie durchtrennten Blöcken mit unterschiedlicher Trennflächengeometrie untersucht. Aus den Ergebnissen der Versuche an intaktem Material wurde ein neues Versagenskriterium für biaxiale Belastungen validiert. Die Ergebnisse der Versuche an intakten und durchtrennten Blöcken wurden verwendet, um ein neues stark nicht-lineares Versagenskriterium für geklüftetes Gebirge unter biaxialer Belastung abzuleiten. Darin wird der Bruchtensor verwendet, um den Einfluss der Trennflächengeometrie auf die Festigkeit zu erfassen. Das Versagenskriterium stellt heraus, welche Bedeutung die mittlere Hauptspannung für die Gebirgsfestigkeit hat. Un mélange de platre dentaire, de sable et d’eau a été utilisé pour développer un matériau analogue des roches fragiles. De fines feuilles galvanisées permettent de créer des discontinuités représentatives des discontinuités naturelles dans des bloques fabriqués avec ce matériau analogue. Les modes de rupture et la résistance, tant pour le matériau intact que pour le matériau avec ses discontinuités, ont été étudiés sur des blocs de 35.6 × 17.8 × 2.5 cm soumis à des efforts de compression uniaxiaux et biaxiaux. Différentes configurations de géométrie de discontinuités ont été considérées. Les résultats obtenus à partir des blocs intacts permettent de vérifier un nouveau critère de rupture pour les roches intactes soumises à des efforts biaxiaux. Les résultats obtenus, tant avec les blocs intacts qu’avec les blocs avec discontinuités, sont utilisés pour développer un nouveau critère de rupture, fortement non linéaire, pour les massifs rocheux soumis à des chargements biaxiaux. Dans ce critère de rupture, un tenseur de fractures est introduit pour caractériser les effets directionnels de la géométrie des systèmes de discontinuité sur la résistance des blocs avec discontinuités. Ce critère de rupture démontre le rôle important de la contrainte principale intermédiaire sur la résistance des massifs rocheux.

Jan 1, 2003

By Thomas A. Phillips

The Bureau of Mines presents an economic evaluation of its leach- electrolysis process for recovering lead from galena concentrate. In this process, galena concentrate is leached at 200° F with a ferric chloride-brine solution to extract lead while leaving sulfur in the residue, which is discarded. The solution after leaching is concentrated and cooled to 100° F by vacuum evaporation to crystallize lead chloride from which metallic lead and chlorine are produced by fused-salt electrolysis. Chlorine is used to regenerate the spent leach solution before it is recycled. A cost estimate was prepared for a plant capable of producing 300 tons per day of lead, 330 days per year. The fixed capital cost on a third-quarter 1977 basis Fs $27,500,000, and the estimated operating cost without a charge for the concentrate is 4.9 cents per pound of lead product. Assuming a selling price for corroding-grade lead of 31 cents per pound and a charge for the concentrate of $332 per ton, the interest rate of return on investment after taxes is 16 percent. The leach-electrolysis process, therefore, appears to be economically attractive under the assumed market conditions.

Jan 1, 1978

By Alan A. Campoli

The mining industry has long been searching for an effective structural application that prevents weathering and falls of loose rock, debris, and sediment. J-Crete is a fiber-reinforced, engineered, cementitious composite rock application that is designed, tested, and successfully utilized as such a material. Laboratory evaluation of J-Crete material properties has shown the final compressive strength to be in excess of 7,300 psi (50.34 MPa), with 24 hour strength in excess of 1,500 psi (10.34 MPa). The flexural tensile strength is in excess of 600 psi (4.1 MPa) and is provided through a unique combination of polyvinyl alcohol (PVA) fibers activated by a proprietary liquid additive that prevents them from clumping and enables even distribution throughout the grout. Tensile bond strength in excess of 350 psi (2.4 MPa) at 28 day cure tightens the strata and holds loose material in place. Practically impervious to gas and liquids, J-Crete protects strata against long-term weathering, does not require screening to be effective, and has proven to be a successful waterproofing material. J-Crete has demonstrated the potential to alleviate coal mine roof cutters in soft, wet clay formations. J-Crete reinforces coal mine ribs by bonding directly to the rib, conforms to the strata, strengthens the rib, and eliminates sloughing due to long-term weathering; stabilizes coal mine entries by bonding directly to the brow and roof, and creates a monolithic shell with double reinforced corners.

Jan 1, 2012

By John A. Dal Pino

This paper describes two independent building underpinning projects during the construction of the Los Angeles Metro Rail System. The first project involves pinpile underpinning of a building along the Red Line which is the main heavy-rail portion of the system. Vertical and inclined friction pinpiles were constructed, using drilling equipment in a low-overhead height space, to support underpinning grade beams. This underpinning permitted the demolition of the building caissons so that the subway tunnels could pass beneath the building unimpeded. One of the piles was statically tested in compression. The second project involves the use of traditional pit piers for the underpinning of historic buildings along the Pasadena Blue Line, which is one of the light-rail branches from the Red Line. The piers were designed for various loading conditions and to minimize differential settlement of adjacent foundations. The piers will be internally braced with steel struts to be designed by the contractor.

Jan 1, 1996

The Midvale Slag Site covers 300 acres in Midvale, Salt Lake County, Utah. Midvale (population 10,000) is part of the Salt Lake City metropolitan area (population 936,000). Between 1902 and 1971, United States Smelting, Refining and Mining Co. smelted ores on the site to produce copper, gold, lead, and silver. Figure 1 shows a picture of the historical Midvale smelter operations. [ ] When operations ceased, the site was estimated to contain 2 million tons of slag from these operations. The smelter no longer exists. In 1971, Valley Materials, Inc., acquired the site to process the slag into materials for railroad beds and asphalt highways. During the 1980s, the U.S. Environmental Protection Agency (USEPA) raised concerns regarding environmental impacts associated with the historical site operations. The Midvale Slag Superfund Site was listed on the NPL in 1991. The Site consists of two Operable Units (OUs): OU1 covering the properties north and adjacent to former ore smelting operations; and OU2 covering the smelter site itself. OU1 had historically been affected by wind blown slag dust and stack emissions occurring on OU2 and the Sharon Steel site further to the south. These emissions resulted in elevated levels of arsenic and lead in the native soils. The EPA issued the final Record of Decision (ROD) for the OU1 Site in 1995. The OU1 ROD required the implementation of institutional controls for the undeveloped portions of OU1 in order to restrict future land use to commercial/industrial purposes unless additional remediation was performed. Hence, the land comprising OU1 was originally considered in the ROD to be suitable for commercial or industrial purposes without the need for remedial action. However, development of OU1 for other land uses, including residential or recreational, would require additional assessment and probable remediation. The OU2 parcel was remediated by EPA to allow future land development, and the Sharon Steel site was remediated by EPA and deleted from the NPL. PROPERTY TRANSACTION AND REDEVELOPMENT In February 2006, a private development company, Mercer Bingham Junction, LLC. (MBJ) purchased 130 acres of the OU1 property for the purpose of performing environmental remediation, and developing mixed residential and commercial real estate. Development of the property was conducted in cooperation with USEPA Region 8 (EPA), the Utah Department of Environmental Quality (UDEQ) and Midvale City. The guidelines under which residential development could occur were defined by EPA. The 130 acres was to be developed for open space, residential and commercial use as part the Midvale City Bingham Junction development. Figure 2 shows the general layout of the proposed land uses. [ ] In May 2005, MBJ began pre-acquisition due diligence activities to purchase the 130 acres of OU1 north of 7200 South Street, which now comprises the Bingham Junction Development. This included the completion of Phase I and limited Phase II investigations. The Phase II investigations were performed to evaluate arsenic and lead concentrations in the planned residential areas of the site, and to explore the contents of the historic landfill on the property. The historic landfill area was on the far west side of OU1, adjacent to the Jordan River. Soil samples collected during the Phase II investigation showed that the planned residential parcels did not currently meet the criteria established in the Tech Memo and that additional placement of fill or soil excavation would be required for residential development in this area. An evaluation performed by the previous owner of the property, Littleson, Inc., showed similar results.

Jan 1, 2009

By Luminita Calin

King County (Seattle, WA) is on a monumental task of building the new Brightwater System complete with a new treatment plant, three main conveyance tunnels, a new outfall into Puget Sound and other ancillary works. This paper will describe the first conveyance tunnel, Brightwater East currently under construction by the Joint Venture of Kenny (Sponsor) / Shea / Traylor that is scheduled for completion in early 2010. The project located in Bothell, WA (north of Seattle) is in both King and Snohomish Counties. It was the first of the major tunnel projects that was scheduled by King County for the Brightwater System. The East Contract consists of the following major elements: 14,000 ft of 19'-2' EPBTBM mined tunnel using 16'-8' ID bolted, gasketed precast concrete segments for a primary liner; installing and encasing 14,200 ft each of 48', 66', 27', 84' in diameter steel pipes inside the tunnel along with three runs of fiberoptic cable; 2,430 ft of 72' in diameter microtunnel including three caisson shafts and associated structures; one Intercepting Structure (IS) shell to mine from that is 74 ft deep and 74 ft finished in diameter with 130 ft deep slurry diaphragm walls, tremie slab and final concrete wall lining; one Influent Pump Station shell (IPS) 83 ft deep, twin 77 ft inside diameter cells, with 160 ft deep slurry diaphragm walls, tremie slab, and final lining; two short 12 ft in diameter inter-shaft connector tunnels; one extraction shaft 40 ft deep by 40 ft wide and 140 ft long for connection to the new treatment plant piping.

By G. Onal, E. Gock, H. Dincer

"During the conventional chromite dissolution process; chromite ore concentrates were ground to at least <90 µm using the ball mill and after adding Na2CO3 and leaning material (instead of CaCO3 also residues from the leaching process) at a ratio of e.g. 1:0.75:1.2, depending on the specific formulation, follows the digestion e.g. in a rotary kiln, heated in countercurrent. The reaction time is 3 to 8 h. The calcine is comminuted and leached with water or a thin chromate solution. Depending on the type of ore used, the yield is 75-85 %. The disadvantage of the above-described process is that it is impossible, using current technology, to achieve a complete digestion of the chromite ores and that the chromium-containing residues have to be disposed of as special waste, involving a large financial effort.The subject of this study was the investigation of the effect of vibratory milling on chromite dissolution. The impact stress in the vibratory mill causes the mechanical activation of chromite, which is characterised by lattice defects. The degree of mechanical activation can be quantified by measuring the relative X-ray diffraction intensities at the parent lattice planes of chromite. Each relative X-ray diffraction ratio correlates with a certain degree of digestion. As opposed to vibratory milling, a complete digestion of chromite using a ball mill is impossible, even at extremely long grinding times.In this investigation a chromite concentrate from Pulpinar/Kayseri with content of 44 % Cr2O3 and the Eccentric Vibratory Mill was used. In order to verify the effect of the vibrating grinding on chromite dissolution, reaction kinetic investigations on digestion and leaching were carried out."

Jan 1, 2003

By D Craw, P Lindsay, B Peake

The geochemical properties of Kaiata Mudstone and Brunner Coal Measures are evaluated in order to determine their suitability for placement at the proposed Cypress and existing Stockton mines. Correct scheduling of this waste material is needed in order to prevent sulfide oxidation and the generation of acid rock drainage. The Kaiata Mudstone has both acid generating and acid neutralizing properties. Results from this study and previous research from Kingett Mitchell Ltd (2003), indicate that within the Kaiata Mudstone sulphur content decreases with distance away from the Brunner Coal Measure/Kaiata Mudstone contact, while calcium carbonate content increases; sulphur values range from 0.33 to 4.23 wt %; and the acid neutralizing capacity ranges from 0 to 10.4 wt %. The Brunner Coal Measures have a low capacity to neutralize acid and sulphur content is variable ranging from 0.25 to 3.5 wt %. Appropriate control measures are therefore needed for the Brunner Coal Measures and any Kaiata Mudstone within close proximity to its contact. Tests have been undertaken to develop a rapid field or laboratory procedure to define the potentially acid-forming from the non-acid-forming Kaiata material. Results indicate that paste pH, Net Acid Generation (NAG) and Carbonate Bomb tests are suitable. Results from the Carbonate Bomb Test show a strong relationship with the Acid Neutralizing Capacity (ANC) and the Net Acid Production Potential (NAPP), indicating that this method may efficiently determine non-acid forming material in the field within fifteen minutes. Ongoing research includes kinetic column and shake extraction tests. These tests will quantify what trace elements could be leached from the waste rock and provide information on the usefulness of alkaline producing products such as Bauxsol, Limestone and Cement Kiln Dust.

Jan 1, 2004

By R. Gallinger, B. Kelley

"In 1997, a group of Canadian mining companies met to review the Mine Environment Neutral Drainage (MEND) program and to consider future activities. They concluded that (1) that Canadian industry and Natural Resources Canada (NRCan) should fund a small secretariat in Ottawa to support technology transfer in Canada and, (2) that it was important for industry to continue the momentum of MEND on an international scale.The need for the International Network for Acid Prevention (INAP) was strongly endorsed by consultants, company, university, and government experts from Australia, Canada, and the United States who convened in Vancouver in February 1998. The initial focus was the development of a solid knowledge base covering the collective experience of INAP’s members to promote the dissemination of successful practices, the identification of knowledge gaps, and the formulation of effective research proposals. The sharing of information on past successes and failures alone was viewed assufficient justification for the formation of INAP.INAP was officially launched in October 1998, and is now an effective, industry-based initiative to globally coordinate research and development in the management of sulphide mine waste. Significant improvements in the management of sulphidic mine materials through knowledge sharing, research, and development of technology by INAP will reduce liability associated with acid drainage.This paper will explore the international efforts and activities of INAP."

Jan 1, 2005