Search Documents

By Ailton da Silva Ferreira

Thermoset polymers, like the polyester, become harder with increasing temperature owing to molecular crosslink formation, which is a thermal benefit for composite matrix applications. Natural lignocellulosic fibers, however, have low thermal resistance and tend to degrade with increasing temperature. Therefore, the combination of a lignocellulosic fiber, as reinforcement, with a thermoset polymer, as the matrix, results in a composite material with complex thermal behavior. In the present work, a thermal analysis was conducted on polyester composites with different amounts of curaua fibers. Both TGA and DTG curves were analyzed to determine the effect of the curaua fiber on the thermal resistance of the composites. It was found that the curaua fiber sensibly affects the thermal behavior of the polyester matrix for fiber amounts above 10% in volume. This effect is associated with an increase in thermal degradation.

Jan 1, 2010

By Patrick Hansert

Safety was always in the focus of Badische Stahlwerke, however at the same time productivity has to increase as well in order to compete in a tough world market. In 2015 BSW produced over 2.2 Mio tons with two EAFs, leading to tap-to-tap times in average of under 40 minutes. Our philosophy has always been, that our most important success factor are the people: therefore we have to improve the working conditions as much as we can. Starting in 2012 Badische developed a robot that can support this goal. The first step was to use it for temp/sample taking, but the unit had to become a multi-tasker. Only 2 years later the first automated cartridge changer was installed at a customer site in Scandinavia, in late 2015 then the next tool was implement: tool changer allows now to use also a camera to check the condition inside of the heat after tapping. More tools are designed currently and will be implemented shortly. This paper describes the current installations and experiences as future applications.

Aug 17, 2017

By S. Ali Bastani, Ashley Varni

Design acceleration response spectra (ARS) are directly correlated with dynamic forces and estimated dynamic bridge displacements, which make them a critical aspect of dynamic bridge design. Nonlinear site response analyses are performed for a 1,400-linear-foot bridge site with a SC soil profile at the sides and a SF soil profile in the middle to evaluate the soil profile effects on the bridge analyses. One-dimensional seismic response analysis is commonly performed for site-specific response analysis. SHAKE or similar one-dimensional total-stress equivalent-linear approaches have been used since the 1970s. However, the equivalent linear method has deficiencies when the subsurface soils are susceptible to strain softening. Therefore, various assumptions are made when using the equivalent linear method by practitioners to estimate the SF soil profile site response. With recent advancements in constitutive models, effective stress models have become more popular. Although the effective stress models are generally more complicated and require additional input parameters, they shed further light on the liquefaction mechanism and its effect on the surface ARS. An equivalent-linear one-dimensional seismic response analysis and a non-linear effective-stress seismic response analysis, using DEEPSOIL, were performed to evaluate the ground surface ARS for a proposed bridge site in Orange County. The soil shear strengths were estimated based on cone penetration test results using empirical relationships. The shear modulus degradations (backbone curves) of soil layers were adjusted to match the estimated soil strength at failure. The ARS curves developed from each method were compared to determine the most suitable method for estimating a site-specific design ARS curve for a liquefiable site. Considering that the bridge abutments and the outer bents are founded in bedrock, while the middle bents are founded in liquefiable soils, ARS curves were created for each subsurface condition. Taking into account limitations of the structural analysis software, recommendations were made to combine the multiple ARS curves into a single ARS curve for the structural bridge design.

Jan 1, 2018

By David J. Lowell

The gold content of porphyry copper deposits ranges from less than 0.05 g/t to more than I g/t ((0.0017 to 0.035 oz per st) and the average is about 0.05 g/t (0.0017 oz per st) gold. Perhaps the highest grade mineralization found near a porphyry cop¬per deposit is the Ok Tedi Gold Cap ore body whose grade falls in the 2 to 3 g/t (0.07 to 0.1 oz per st) range. It is difficult to define a gold-rich por¬phyry copper deposit. All porphyry copper ore bodies contain some gold, but there seems to be a fairly sharp break in the gold content at about 0.1 g/t (0.003 oz per st) gold. There is also a problem in identifying dis¬seminated gold deposits that may have an indirect relationship to porphyry copper systems. This relationship is clear cut in deposits such as the Ok Tedi Gold Cap, the El Hueso deposit, the Fortitude and West de¬posits at Battle Mountain, NV, and the Sur¬prise deposit at Ely, NV. There are many other bulk disseminated, epithermal-type gold deposits - McCoy, NV, for example - that might be related to a porphyry system but where this relationship is remains very uncertain. In such places as the Goldfields and Tonapah district in Ne¬vada and in the El Indio, Chile district, there may be a vertically stacked ore deposit rela¬tionship between near surface epithermal deposits and disseminated molybdenite and chalcopyrite enargite mineralization at depth that may represent a deep porphyry system. This, however, has not been positively demonstrated. Most of the bulk epithermal gold deposits are probably not related to porphyry copper systems. Exceptions would probably be Ok Tedi, El Indio, El Hueso, Battle Mountain, and Lepanto where vertical or lateral zoning relationships are more apparent. This author believes that porphyry copper systems are related to a relatively unique type of intrusion that is probably distinct from, for example, the McCoy intrusivebody. For that reason, deposits such as McCoy, Chimney Creek, and the like will not be included in the definition of gold-rich por¬phyry copper deposits for this article. The interpretation of the origin of several of the deposits previously mentioned are subject to an unusual amount of contro¬versy. For example, geologists seem to be equally divided about the presence of a porphyry copper deposit below the El Indio deposit. Geologic setting Continental vs. island arc Several geologists have speculated that the gold-rich, moly-poor, porphyries are

Jan 1, 1989

By Wern-ping (Nick) Chen

The Florida Department of Transportation District 6 (FDOT D6) began a study in 1987 for a master plan to improve the traffic circulation and congestions between the Port of Miami (POM) and downtown Miami, FL. This study included a tunnel connection between two man-made islands, the Watson and the Dodge islands. Though a finding of no significant impact (FONSI) was completed in 1992, the project remained on hold for about 10 years. In 2002, Florida Turnpike took over this project, re-evaluated its benefits to the lo-cal communities, determined its feasibility (specifically the tunnel options) and established a probable cost. In 2005, the FDOT D6 regained its charge over the project and concluded that a bored tunnel under Biscayne Bay is feasible. Its primary components are: ? Widening of the MacArthur Causeway Bridge, to accommodate truck traffic to the Port of Miami. ? A tunnel connection between Watson Island and Dodge Island, where the POM is located. ? Connections to the POM roadway system, either for the traffic from the city of Miami or for the truck traffic from I-395 to the POM. The project will improve access to and from the POM and provide a dedicated roadway connector linking the POM with the MacArthur Causeway (State Route 41/1) and I-395, specifically for the trucks in and out of the POM without going through downtown Miami. As identified in the project information memorandum (PIM), its primary objectives are to: ? Improve access to the POM, helping to keep it competitive and ensuring its ability to handle projected growth in its cruise and cargo operations. [ ] ? Improve traffic safety in downtown Miami by removing POM traffic, trucks and buses from the congested downtown street network and, in doing so, facilitate ongoing and future development plans in and around downtown Miami.

Jan 1, 2009

By K. J. Liles

The Bureau of Mines conducted laboratory semicontinuous and continuous heavy liquid tests to determine the feasibility of producing commercial-grade products from the high-clay sylvinite ores of the Permian Basin in New Mexico. Continuous test operations demonstrated that concentrates containing 59.9 percent K2O and recoveries of over 75 percent of the contained potash can be obtained. The organic heavy liquid was effectively recovered by vaporization, condensation, and absorption methods. Less than 5 parts per million of heavy liquid vapors were released to the atmosphere. This loss represents only 0.02 pound of heavy liquid per ton of ore treated.

Jan 1, 1973

Pilot-Scale Study of Deep Cone Thickener for Phosphatic Clay Dewatering

Sep 13, 2010

In September 2003, a test was conducted to see if a115-mm- (4.5-in.-) diam Mocap Vari-Stem blasthole plug could improve the pattern of explosives using different top stemming material. The test took place at the J.S. Faulkroad and Sonsstone quarry in McCalisterville, PA. The test consisted of a production stone blast. Half of the holes were stemmed with standard crushed stone. Two-thirds of the remaining half were stemmed with Vari-Stem plugs and crushed stone. And the remaining one-third of the second 50 percent was stemmed with Vari-Stem plugs and only drill cuttings.

Jan 1, 2004

Many industries base their decisions on the assaying of tiny analytical sub-samples. The problem is that most of the time several sampling and sub-sampling stages are required before the laboratory provides its ultimate assays using advanced chemical and physical methods of analysis. As long as each sampling and sub-sampling stage is the object of due diligence using the theory of sampling it is likely that the integrity of the sought after information has not been altered and the generated database is still capable to fulfil its informative mission. Unfortunately, more often than not, unawareness of the basic properties of heterogeneous materials combined with the unawareness of stringent requirements listed in the theory of sampling, lead to the conclusion that massive discrepancies may be observed between the expensive outcome of along chain of sampling and analytical custody, and reality. There are no areas that are more vulnerable to such misfortune than sampling and assaying for trace amounts of constituents of interest in the environment, in high purity materials, in precious metals exploration, food chain, chemicals, and pharmaceutical products. Without the preventive suggestions of the theory of sampling serious difficulties may arise when making Gaussian approximations or even lognormal manipulations in the subsequent interpretations. A complementary understanding of Poisson processes injected in the theory of sampling may greatly help the practitioner understand structural sampling problems and prevent unfortunate mistakes from being repeated over and over until a crisis is reached. This paper presents an overview of the theoretical, practical and economic difficulties often vastly underestimated in the search for quantifying trace amounts of valuable or unwelcome components.

Jan 1, 2010

By Gerald Greene

Tan various lead producers have given the subject of lead drosses much attention in recent years but the problem of their economical treatment is yet to be solved. Formerly the copper in the furnace feed was removed from the furnace in the form of matte. The speiss at that time consisted principally of the iron arsenide. The practice today is to roast off most of the sulfur and the copper in the feed forms a dross in the furnace, which is removed from the furnace with the lead. This material is poured into the drossing kettles and allowed to cool down to but slightly above the freezing point of lead. The copper dross, containing almost all of the arsenic and part of the antimony, is skimmed off and treated in a small reverberatory furnace at most plants. This is essentially a liquation process. The skimmed dross contains from 70 to 80 per cent lead, and much of this lead is liquated out. The products from this treatment are: (1) impure lead, (2) speiss and (3) matte. The speiss from the reverberatory furnace was studied in this research. The literature on the subject is of very little assistance, as almost no work has been done on the problem of establishing the exact identity of the various phases present. One author(1) states that speiss consists of a series of isomorphous compounds of the general formula FexAsy in which the Fe may be replaced by Ni, Co, Cu, Pb, Ag, Au, Pt, Zn, Cd and the As replaced by Sb, S and Bi. Hofman(2) states that the iron arsenide present is Fe5As.

Jan 1, 1935

By Frank W. Luerssen

Introduction "Austerity" is perhaps an overly generous description of the past three years in the American steel industry. Steel plants operated at an average of only 57% of their capability in 1982-84. The dismal losses for last year are still being totaled. But during the two years before this period, American steelmakers recorded an aggregate net loss of a staggering $6.8 billion. Steelmakers responded by closing numerous marginal facilities. And production capability was cut by 13.6 Mt (15 million st). Capital expenditures still averaged $2 billion annually. But this was inadequate to maintain the existing base of steelmaking facilities. The general economy experienced a satisfactory recovery during this period. American steel, however, continued to suffer from a lagging recovery in the capital goods sector. This was due to record penetration of its domestic market by imports and from very weak realizing prices on the volume that was available. In addition to the direct influx of offshore steel products - which itself depressed prices - the industry also became painfully aware of the growing importance of "indirect" imports. These came in the form of steel-containing producer and consumer durables. Industrial equipment and autos fabricated from foreign steel accounted for the equivalent of 6 Mt (6.5 million st) of lost market opportunity for domestic steel-makers last year. That is over and above the 23.5 Mt (26 million st) of direct steel imports. Given these factors, Inland Steel was not spared from the threeyear downpour of red ink. Despite its record of continuing modernization in steel, our single-plant location in the world's best steel-consuming market, and the high proportion of consumer durables related products, such as cold rolled and coated sheet in our mix, Inland suffered aggregate losses of $277 million during the 1982-84 period. Strategic Planning The foregoing establishes a perspective - a base from which we have restructured our view of the steel industry, and of our own role within that picture. Until possibly two years ago, this present weakness in steel demand was viewed around the world as an aberration, eventually to pass. By contrast, it is now recognized that austere times are the normal steel environment. The topic here is management of resources. This implies an emphasis on strategic planning. It is worthwhile to examine some of the more critical assumptions that were driving strategies among a number of steel companies just before the 1980s. Those projected characteristics of the future steel environment were arrived at through painstaking analysis. They were carefully and heavily quantified and were generally shared by outside observers and our peers within the steel industry. • First, the assumption was made that domestic steel demand would continue to grow at an average rate of 2% per year. • Second, it was assumed that this growth in the American market would continue to be filled predominantly by US mills. It was believed that increases in steel and steel-related demand overseas would absorb much of the ominously growing capacity of third

Jan 6, 1985

By Colin Hardie, Erik Bartsch, Guy Comeau

"The Xstrata Nickel Raglan Concentrator, located at the northern limit of Quebec’s Nunavik region has been in operation since 1997. Originally designed to process 800,000 tonnes per year of high grade nickel ore, plant capacity is currently approaching 1,200,000 tonnes per year due to an Optimization Project (FAG to SAG conversion) in 2005 and many recent processimprovements.In 2006, the Raglan Metallurgical Group with assistance from the Xstrata Process Support group decided to make SAG control one of its priorities in order to further increase throughput and improve stability. The original primary mill control logic delivered by the Optimisation Project in 2005 consisted of a simple PID loop controlling the mill charge (bearing pressure) through feed rate changes. Due to the multivariable, non-linear and disturbance dominated nature of the SAG circuit it was quickly found that this traditional PID control strategy was not able to adequately control the mill; resulting in poor stability, frequent operator interventions and less than optimum performance.This paper describes the successful integration of advanced field systems such as mill feed image analysis (Wipfrag) and crusher gap controller (ASRi), into a multi-variable fuzzy logic SAG mill controller. The process of how a strategy for control was developed and implemented directly in the existing control system (exploiting standard system capabilities) is discussed. It is also shown how this approach has provided mill automation which is simple, robust (despite erratic feed characteristics), and delivers both an increase in throughput and a reduction of variability.INTRODUCTIONOriginally commissioned as a Fully Autogenous Grinding (FAG) circuit in 1997, preparations to convert the Katinniq Concentrator Mill to SAG had in fact commenced as early as 1999, but were halted owing to alternative process improvements which achieved up to 1Mtpa as early as 2000. Up until this time, plant process controls had remained more or less static; modifications having been limited to those required by new equipment. Primary mill process controls and related measurements were at this stage limited to:"

Jan 1, 2008

By W. H. Yarroll Discussion by W. A. Griffith

W. A. Griffith (Head, Research Department, Phelps Dodge Corp., Morenci, Ariz.) - It is gratifying to see the increasingly common use of classical statistical procedures by metallurgical researchers. Mr. Yarroll has given excellent illustrations of the utility of multiple correlation analysis of complex metallurgical data. Our experience in applying these procedures to historical plant operating data has differed, however, from that which he suggests. The uninitiated frequently assume that the volumi-

Jan 1, 1969

By W. A. Gow

"In January of 1964, a group known as the Canadian Gold Metallurgists was formed with the backing of the managers of most Canadian gold mining operations. This organization is composed of about thirty mill superintendents of Canadian gold milling operations where the cyanidation process is in use, and one member from the staff of the Mines Branch, Department of Energy, Mines and Re-sources, Ottawa. The aim of this group is to bring together gold mill operators, and research and development people from both industry and government for the purpose of discus-sing common metallurgical problems, and deciding on what operational R and D efforts can be made to help solve these problems. Since the conception of this organization, this approach taken by the gold industry to the study of metallurgical problems has resulted in benefits to all operators, both by assisting them with problems peculiar to their own individual operations and by providing developments of general interest to the industry.This paper describes events leading up to the formation of the Canadian Gold Metallurgists, and how the group has operated since its formation. Examples of progress made toward the group's objectives are given, and possible future programs are discussed."

Jan 1, 1968

By M. W. Grabinsky, M. S. Diederichs, E. Hoek

Provided that they are used correctly, numerical models can be of considerable assistance to mining engineers in designing underground excavations. Guidance is given to the engineer or geologist who is not a specialist in numerical analysis but who is interested in using numerical modelling tools or in employing someone to analyse the stresses, displacements and failure in the rock surrounding underground excavations. A description of the theoretical background to a number of these numerical models and discussion of the advantages and disadvantages of each are followed by guidelines on the selection of appropriate models for each stage in the development of a mine, from exploration to the completion of mining

Jan 1, 1991

By L McCracken

Up until 1990 CoalCorp North Island's accident record was six times that considered acceptable in those NSW operations with good accident prevention programmes. This was an obvious avoidable burden on the company in both human and cost terms.   Late in 1989 an accident prevention programme was implemented with the objective of achieving a 50 per cent reduction in the lost time accident frequency rate within 12 months. The key to achieving this objective was recognised as being an attitude change in the total workforce from General Manager downward. Management commitment and action were seen to be critical to the success of the programme.   Through very basic and simple training programmes in accident investigation, analysis and reporting, communication, on-the-job coaching and in focusing on improving supervision skills, the original objective was achieved.   During 1991 the application of methods improvement and hazard recognition techniques are seen as the logical step to achieving a further 50 per cent reduction in the accident frequency rate.

Jan 1, 1991

By Bill York-Feirn

The Colorado Mine Safety & Training Program (MSTP), in late 2005, completed and began distributing two new training tools; one geared to underground coal mine foremen and the other to surface aggregate employees. Through strong partnerships with MSHA, Colorado Coal Mine Board of Examiners, Colorado Mining Association and the Colorado Rock Products Association, the MSTP continues to create innovative and interactive training tools for not only Colorado, but for the national mining community. "Although we shoot and produce these materials in Colorado, it's important to us to make sure they are useful nationally," said Bill York-Feirn, MS TP Manager. The interactive DVD program "Underground Mine Foreman Certification Study Guide (Coal)," was completed in October 2005. It won the 2005 Grand Prize at the MSHA National Training Materials Competition in Beaver, West Virginia. [ ] This program is fully based upon the requirements of Title 30 Code of Federal Regulations (30 CFR) Parts 48, 50, 70 and 75 for underground coal mine foremen. It contains eight modules plus immediate access to relevant laws in the appendix. Topics covered include: Federal Law, Practical Math Skills, Mine Gases, Ventilation Maps, and scenarios addressing a variety of practical mining concerns. The DVD is designed for self-¬paced study and practice.

Jan 1, 2006

By D. Death

The Tapping Camera Prototype (TCP) is an instrument being developed to record and analyse video of the molten metal stream entering a tapping crucible as it is tapped from an aluminium reduction cell. The development aims to provide potroom floor operators with continuous real time vision of the tapping process and provide an alert in the event of excessive bath contamination in the extracted metal stream. Longer term the system may provide sufficient data to enable control of the tapping process. The TCP mounts a wireless camera and periscope to view the molten metal stream via a peephole in the tapping crucible. Real time video is recorded to either digital video tape or computer disk for subsequent video analysis to quantify the bath material drawn into the tapping crucible with the molten aluminium. The images transmitted by the camera are available on a handheld LCD video screen. This work is an initiative of the CSIRO?s Light Metals Flagship.

Jan 1, 2006

By A. Krishnan

Keywords: Tantalum extraction, SOM Technology, inert anode, membrane stability The Solid Oxide Oxygen Ion conducting Membrane (SOM) technology offers great potential for environment friendly and energy efficient extraction of high-energy content metals. This work was performed to demonstrate the technical and commercial viability of the technology to produce tantalum metal directly from tantalum oxide and ore concentrates using a solid-oxide, oxygen-ion-conducting membrane (SOM). The process can be used to efficiently produce tantalum metal without expensive pre-processing of raw materials and without harmful by products. The work reported in this paper is: the proof that high purity tantalum metal can be produced, study of the electrochemical behavior of the cell and the method to increase membrane stability.

Jan 1, 2005

Ferrochrome is the major chromium source for stainless steel production, and submerged-arc furnaces (SAF) are most commonly utilised to smelt chromite ores into ferrochrome by using suitable carbonaceous reductants such as coke. Because of the complexity of feed structure and electrical-thermal-chemical interactions, there exist large gradients and wide distributions of temperature, mineralogy and other process variables in the furnace. This leads to various zones in the furnace, and different reduction mechanisms. Control of the furnace is thus often difficult due to the complicated physical and chemical situations in the furnace. The temperature profile in the submerged arc furnace has a great influence on the reduction rate and the production efficiency. Therefore, the energy generation through electrical arcs submerged in the solid feed and its distribution within the packed bed play an important role. In the present paper, an overall process model is illustrated to simulate inter-linked transport processes of fluid flow, heat transfer and reduction kinetics within the submerged arc furnace. The application of reaction kinetic data to simulate the chromite pellet/lumpy ore reduction with CO gas is presented and further adjusted to provide a submodel for a flow and heat transfer simulation for the packed bed by using computational fluid dynamics (CFD) technique. The comprehensive process model is aimed to simulate materials and gas flow, temperature and energy distribution throughout the furnace system. A preliminary model for gas flow and temperature distribution for the upper part of a 20 MW furnace (the packed bed) for high carbon ferrochrome production has been developed under simplified conditions. The integration of the reaction kinetic model into process simulation, and the future vision for a more comprehensive process modelling are discussed. It is expected that better understanding of the furnace insights through process modelling will help process optimisation and furnace control.

Jan 1, 2004