Search Documents

By S. Pauly, U. Kühn, J. Eckert, I. Kaban, G. Wiehl, F. Silze

In the present work, the effect of Ga on the wetting behavior of the Cu-rich braze filler CuGa10 (wt.%) on the steel 304L was investigated. For this, the macroscopic and microscopic effects governing the wetting of pure Ga, pure Cu and CuGa10 alloy (wt.%) on the austenitic steel were analyzed and compared. Contact angle and surface tension measurements were carried out by means of the sessile drop technique and, in addition, the phase formation at the interface was determined. Pure liquid Ga spreads on 304L, which supposedly is related to the formation of intermetallic Fe-Ga phases growing into the liquid Ga. Depending on the annealing time, FeGa3 and Fe14.5Ga12 were identified. In contrast, CuGa10 as well as pure Cu show secondary wetting on the steel surface. Especially, liquid Cu prefers to spread laterally and vertically along the grain boundaries of the steel substrate. In spite of rather similar mechanisms, CuGa10 wets 304L steel at lower rate than pure Cu above the liquidus temperature.

Jan 1, 2014

By T. T. Read

"Employee representation in the management of large mining enterprises was first introduced in organized form, by the Colorado Fuel and Iron Co. in 1915. Within the past few years a number of the larger mining enterprises have introduced similar systems and there is growing interest in the subject. This will be stimulated by the final report of the President's Second Industrial Conference, in which the following statement occurs:""The conference finds that joint organization of management and employees where undertaken with sincerity and good will has a record of success. The general principles governing such organizations are stated at length under the title 'Employee Representation. It is not a field for legislation, because the form which employee representation should take may vary in every plant. The conference, therefore, does not direct this recommendation to legislators but to managers and employees.""If the joint organization of management and employees in the plant or industry fails to reach a collective agreement, or if without such joint organization, disputes arise which are not settled by existing agencies, then the conference proposes a system of settlement close at hand and under Government encouragement, and a minimum of regulation. The entrance of the Government into these problems should be to stimulate further cooperation."""

Mar 1, 1920

By S. Rajendran

Gas Hydrates (Methane Hydrates) are solid, ice ? like substances composed of water and natural gas. They occur naturally in areas of the world where methane and water can combine at appropriate conditions of temperature and pressure and are found in the ocean bottom sediments and in some permafrost areas. Besides temperature and pressure, factors like bathymetry, sediment thickness, sedimentation rates, and total organic carbon content (TOC) also control gas hydrate formation in the sea. The stability of gas hydrates depends on the critical high pressure ? low temperature combination (0-17 bars, 0-25ºC), which in turn dependent on the mix of gases from which the mineral is formed. As the critical parameters can be altered by deposition, erosion or slumping of sediments, formation or melting of ice cover, rise and fall of sea level and sudden temperature changes induced by tectonic activities, current flows or volcanisms, the gas hydrates tend to be very unstable. It is becoming increasingly evident that naturally occurring gas hydrates are significant component of the shallow geosphere and are of societal concern in at least three major ways: as an energy resource, a geologic hazard and a major contributor for climatic changes.

Jan 1, 2010

By Ivette E. Torres

The estimated value of world crude mineral production in 1992 was $1,633.3 billion in terms of current (1992) dollars, or $1,178.0 billion in terms of constant 1983 dollars. This latter figure was 4.8% above the 1992 level but was 2.4% below the record-high level of $1,207.1 billion 1983 dollars set in 1980. Table 1 provides the latest available revised time series of the estimated value of world crude mineral production both in terms of 1983 constant dollars and in terms of current dollars. The statistical base for this estimation is derived from the data on the value of production of a group of key commodities that was published in the authoritative French language mineral industry periodical, Annales des Mines, for selected years up to 1983. The aforementioned values and those presented in the table are for crude minerals only and only begin to suggest the impact that the mineral industry has on the world economy. These figures represent only the value of mineral materials as they are mined or otherwise extracted from the Earth. They do not reflect the value added to these materials through downstream processing within the facilities commonly accepted as mineral industry plants. That is, value added through beneficiation of ores, smelting, refining, and similar processing is not included in these figures. Comprehensive world data on the value added by such processing are not available; however, a conservative estimate of the total value of processed output from mineral industry plants derived wholly from primary (newly mined) materials would be on the order of about $2,800 billion constant 1983 dollars or $3,900 billion in terms of 1992 dollars.

Jan 1, 1994

By J. D. Davis

On May 15, 1936, Congress authorized the Bureau of Mines to conduct certain studies, experiments, and investigations of subbituminous coal and lignite .4/ Appropriations were made in July 1937, and since that date an active investigation has been underway to complete the provisions of the act. Part of the investigation has included a comprehensive survey of the known properties of the lower-rank non-coking coals, and provisions were made to obtain more data on certain varieties. In line with this plan, a typically subbituminous coal was selected for an extended series o tests in the standard Bureau of Mines-American Gas Association unit,5/ at the Central Experiment Station. This particular noncaking coal was the first one of its rank that ha& been tested in the apparatus; for this reason the results are of particular interest because the testing apparatus was originally designed for use in studying the coke- and gas-making properties of coking coals. The test as described below has been developed by the Bureau of Mines since 1927 through a cooperative agreement with the American Gas Association.6/ Ninety to 180 pounds of coal is heated in a circular retort, 13 to 18 inches in diameter, at wall. temperatures ranging from 540°C. to 1,110°C. in 100°C. steps. All products axe collected and measured; their physical and chemical properties axe then carefully determined to ascertain the gas- and coke-making properties of the coal.

Jan 1, 1939

By Arthur Bell

(San Francisco Meeting, September, 1915) . PRIOR to 1908 the oil production in the State of California, had been almost entirely a heavy fuel, oil, with a high flash point, hut changed within a-short period to a large percentage of refining oil with a low flash, by reason of the coming in of the Santa Maria field, the Midway field, and the increased production of the Fullerton field. This is clearly shown in the following tabulation of California's production: Year Barrels . Below -20° Be, Above 20° Be,, Per Cent_ Per Cent. 1905 48,307,000 90 10 1910 77,698,000 SO 20 1912 90,075,000 6o 31 1914 10:3,600,000 47 53 The bringing in of these high percentage's of light oil with their dangerous low flash and the increasing demand for the refined products necessitated the devising of some cheap and efficient means of quickly separating the lighter elements either in the field or at the main distributing points; also it became necessary to remove the excessive percentage of water which many of the light oils carried in emulsion.

Jan 9, 1915

By Leandro Gusmão da Silva

Neste trabalho, foram estudados os efeitos da irradiação de uma superfície polida do aço inoxidável tipo ASTM F138 com laser de pulsos ultracurtos. As irradiações foram realizadas variando-se a velocidade de varredura do laser, ou seja, a taxa de sobreposição espacial de pulsos. Foi observado que após a irradiação houve uma visível mudança na coloração da amostra. Também foi verificado que com o aumento da taxa de sobreposição de pulsos a superfície tendeu a tornar-se preta, ou seja, absorvedora de luz. Com essa técnica, pode-se realizar marcações com alto contraste sem que haja formação de camadas de óxidos, nitretos ou alterações microestruturais no metal, o que é importante para um material com a precisão que um implante exige.

Aug 17, 2017

By Azizan A

The paper presents the results of chlorination of beneficiated rutile and struverite (a tantalum-niobium bearing, rutile type mineral in alluvial tin deposits) by carbon tetrachloride in the range 623¦K to 773¦K. The chlorination of rutile could reach near completion at 773¦K in about an hour. The process was found to follow a modified pore-blocking law, with the basic reaction constant K varying inversely with the particle size, so that the basic process may be a reaction under interface control (chemical control) as modified by the pore blocking effect. The pore blocking factors for the various experimental conditions were evaluated and the predicted curves showed good agreement with the experimental data. In the case of Struverite, a similar kinetic behaviour was observed but the chlorination process was relatively slower than that in rutile. It was also observed that in struverite, niobium got chlorinated faster, followed by tantalum and titanium, indicating a good possibility of separation by chlorination using carbon tetrachloride.

Jan 1, 1996

By Jr. Reistle

The tests reported in this paper were made in the East Texas field in the summer and fall of 1932 as a part of the Bureau of Mines study of the operation of flowing wells and reservoir performance; and to determine, if possible, the minimum reservoir pressure necessary to produce the wells in this field by natural flow through different sizes of flow strings. The minimum reservoir pressure that would be required to Maintain natural flow through 2 1/2-inch tubing was determined experimentally for the existing energy conditions in the East Texas field. With the present available data, however, it is impossible to predict accurately or to determine by calculation the necessary energy requirements for maintaining the vertical flow of oil and gas mixtures under all conditions. Although some valuable data were obtained which seem to have application to the solution of problems involving vertical flow, this important research of the petroleum industry is so involved that more study of the complicating factors influencing the flow of oil-gas mixtures through vertical pipes is required.

Jan 1, 1933

By W. Gundaker, F. C. Schwerer

Natural chromium-bearing spinels (chromites), which are used as refractory materials in basic steelmaking, are the only commercially important chromium ore and are also encountered as difficult-to-separate contaminants in ore deposits of potential economic value. Techniques for characterization and separation of ore materials frequently are dependent on the magnetic properties of the constituent minerals. An experimental program was initiated to explore the effects of temperature and of simple mechanical and thermal treatments on the static magnetic properties of several ore-grade natural chromites. Studies of the temperature dependence of the magnetic properties showed that the natural chromites, which are dilute in the magnetic ions Fe and Cr, order magnetically only at cryogenic temperatures. However, mechanical treatment in the form of crushing produces a magnetic component that is ordered at room temperature and that is of sufficient strength to alter magnetic-separation characteristics. The additional magnetic component apparently is associated with surface structures which develop during crushing and disappear after heating to above about 500°C. Preliminary studies indicate that this surface structure enhances the susceptibility of the chromite grain surfaces to gas reactions at moderate temperatures.

Jan 1, 1976

By Adriana de Oliveira Vilela

A produção de carvão vegetal em Forno Container Rima (FCR) consiste em um processo semi-contínuo composto por fornos cilíndricos metálicos móveis, com exaustão forçada dos gases. Cada ciclo se divide em 4 fases: carregamento, carbonização, resfriamento e descarregamento. Após o carregamento com toletes de madeira, 20% de umidade, o forno é deslocado para plataforma de carbonização, onde permanece por 3 a 4 horas. A entrada de oxigênio no interior do forno é regulada para controle das reações de pirólise. Todos os gases gerados são conduzidos a um sistema de queima para aproveitamento da energia e eliminação do metano. O peso, a temperatura e a pressão no interior do forno, bem como a vazão, composição e energia do fluxo de gás, são monitorados continuamente, em tempo real. A carbonização finaliza quando é atingido o rendimento gravimétrico de 35% em carvão e 60% em gás. O carvão ainda quente é transferido para cilindros de resfriamento, permanecendo por 12 horas. O forno então, é novamente carregado e se inicia um novo ciclo. Cada plataforma de carbonização pode gerar 1MWe de potência elétrica, produzir 20t/mês de alcatrão, 450t/mês de carvão vegetal e eliminar 500t/mês de CO2 equivalente. Cada FCR substitui 60 fornos Rabo Quente, reduzindo em mais de 50% a mão-de-obra braçal dos processos tradicionais, pela valorização, humanização e qualificação deste trabalho. O carvão produzido atende aos quesitos necessários para uso como redutor na metalurgia e na siderurgia.

Aug 16, 2017

By Dight P. M

The challenge of narrow vein mining is to produce ore with as little dilution as possible, at the least cost -commensurate with the increasing degrees of safety being demanded for mine workers by the modem 'duty of care' legislation. Geotechnical factors play an important, if not overriding, role in these areas. The geotechnical factors cover the complex interaction over a period of time, between the in situ and induced rock stresses, rock structures, rock mass strength and the cable, rock bolt and other ground support members. In the Archaean schist belt areas where many of our narrow vein mines occur the pre-mining in situ rock stresses are commonly significantly higher than the overburden stresses. These are concentrated in areas beneath previous open pits and may be highly concentrated in the pillars and abutments of stopes on narrow veins. The presence of high in situ stresses may be suspected from the appearance of drill cores and underground development long before they become sufficiently concentrated by mining to cause damage or bursts. These initial indications are discussed and modem low cost methods of stress measurement are described. Practical and quick methods of analysing the stress redistribution around scopes and other underground excavations are now available and guidelines for interpreting them in terms of rockmass characteristics, stope stability and support requirements are developed with the object of increasing safety, whilst reducing overall costs and dilution.

Jan 1, 1993

Induced microseismicity monitoring is: ?Essential tool in improving the geotechnical understanding about a mine and its inaccessible surrounding rock masses. It helps to determine: -Event timing, location, and magnitude - identification of highly stressed areas -Event source mechanism - the physics of fracturing in its seismic source region -Seismic strain-rate distribution in 5D - identification of stress concentration or migration patterns -Geomechanical interpretation - identification of hidden geological structures or weaknesses in the ground -Strategy for mining e.g. by a block caving method - maximization of mine production and to optimize ground support design -Potential of future seismic hazards -Large event re-entry protocol, to improve mine safety ?The norm as part of mine safety maintenance and long-term mine design practices

Aug 1, 2013

By C R. Ure

To substantially reduce, if not eliminate, carbon dioxide (CO₂) emissions from ironmaking it is necessary to convert from blast furnace (BF) ironmaking using coking coal as the reductant to direct reduction (DR) ironmaking using hydrogen (H₂) and green electricity. Currently, almost all natural gas (NG) based direct reduced iron (DRI) production utilises iron oxide pellets in shaft furnaces, as opposed to fines in fluidised beds. Also, these pellets are ordinarily produced from high-grade magnetite concentrate, rather than hematite and goethite with typically higher gangue contents. The use of high-grade magnetite concentrate is driven by the preference to melt DRI in conventional electric arc furnaces (EAFs), thereby avoiding the basic oxygen furnace (BOF) for making crude steel (CS). However, in replacing BF with DR ironmaking it is not economically feasible to source enough high-grade magnetite to replace the lower grade hematite and goethite currently consumed. That is not to say that hematite and goethite, or even low-grade magnetite, cannot be used in DR ironmaking. However, their higher gangue content, resulting in higher slag production, requires that the EAF producing CS be replaced with a submerged arc furnace (SAF) that will produce pig iron (PI) for the BOF as does the BF. Here, critical issues to be addressed are, what are the technicalities in replacing high-grade magnetite concentrate with hematite and goethite and NG with H₂ in DRI pellet production and melting? This paper summarises certain relevant published information on DRI pellet research, test work and production together with relevant information on Pilbara ores. It attempts to illustrate the inter- relationship of composition and processing conditions on DRI pellet properties. It is intended to serve as a rudimentary guide to understanding the complexities of formulation, testing, evaluation, production and goethite and offer insight into this challenge.

Sep 18, 2023

By P. C. Lightfoot, J. M. Duke, A. J. Naldrett

"The segregation of magmatic sulphides from mafic and ultramafic silicate magmas, in many circumstances, leaves the magma with a lower-than-normal Ni/MgO ratio, which is characteristic of both lavas erupted from the magma chamber and olivine crystallizing within it. Two end members of the segregation process are discussed; i) batch segregation and ii) fractional segregation.In the former, the critical factor is the magma/sulphide ratio. Computer modelling suggests that where this ratio has been less than 1000, the magma will be recognizable as anomalously low in Ni, due to sulphide segregation, and thus a good target for exploration. In fractional segregation, the critical factors are the proportion of sulphide to silicate being segregated and the degree of fractionation.Samples believed to represent the liquid portion of komatiitic lava f lows from a series of unmineralized sequences in the Abitibi greenstone belt, Canada. Belingwe belt, Zimbabwe, and Barberton Mountainland, South Africa coincide with the sulphide-free fractionation model. They are in marked contrast to samples from the ore-bearing districts of Kambalda and Scotia. Western Australia in which distinct Ni depletion, corresponding to fractionation of olivine plus sulphide in a ratio of between 100 and 200:1 is recognizable. Ni-depleted olivines also mark the sulphide-bearing Dumont intrusion of the Abitibi belt.The Moxie intrusion of northern Maine has distinctly Nidepleted olivines, as does the nearby and petrologically related Katahdin body. In both of these intrusions, the composition of the olivine allows reasonable predictions to be made of the Ni tenors of sulphide showings within them. At Katahdin, the Ni depletion is so widespread that little hope is help out for the presence of economic concentrations of sulphide. At Moxie. the olivine compositions suggest that the best chance of economic sulphides lies in the southern lobe of the intrusion.Ni-depleted olivines also characterize certain rock units within intrusions of the Insizwa complex, Transkei, Southern Africa. Many millions of tonnes of Ni have apparently been removed by sulphides from these rock units, many more than are contained within the single mineralized occurrence so far identified at Waterfall Gorge."

Jan 1, 1984

By M Scoble, R A. Hall

The mining industry has aggressively sought competitiveness through increased productivity and return on investment. A primary strategy has been the pursuit of economies of scale. This has also been dependent upon the implementation of new technology and systems integration. System integration has been accomplished through the implementation of mine dispatch, global positioning and mine wide communication technologies. These technologies have tended to advance at different rates of development and implementation. The result has been that across the industry, and even within companies, mines are at various stages of operational system re-engineering in these areas, driven by improvements in productivity and operational efficiency. Although this strategy has been successful, little effort has been made to analyse change in operational performance in order to understand and model the effects of scale in a quantitative manner. This paper considers the particular impact of equipment scale, together with potential future trends. It then presents and demonstrates a preliminary method to quantify through simulation the anticipated benefits of economies of scale.

Jan 1, 2003

By Gabriela Olsson Schneider

Dentre os materiais que representam a crescente e alarmante quantia de resíduos sólidos gerados nos últimos anos, destacam-se polímeros como o poliestireno expandido (EPS), material largamente depositado no ambiente natural. Propõe-se, portanto, seu uso na composição de uma resina veículo para tinta, em adição ao óleo essencial de casca de laranja. Assim, estabelece-se o objetivo de avaliar as propriedades do fluido resultante e da película seca, incluindo sua interação com diferentes superfícies de madeira. Observa-se que a resina possui viscosidade elevada e tendência ao comportamento não-newtoniano pseudoplástico, bem como alta homogeneidade e mais de 95% de adesão a superfícies de pau-marfim. Avaliações da resina aplicada em MDF sugerem que se deve evitar a aplicação em faces fibrosas de blocos e placas deste tipo de madeira, dado que, ao contrário de sua superfície lisa, não há formação de revestimento visível mesmo após a aplicação sucessiva de três camadas de resina. Conclui-se que, considerando a aplicação de resina em superfícies lisas de madeira, há viabilidade técnica de produção de tinta a partir da resina veículo em estudo.

Aug 17, 2017

By M. R. Geer, H. F. Yancey

Four coals were treated in the Humphreys spiral concentrator, and the products were examined by float-and-sink and screen-sizing tests to determine fundamental performance characteristics. The efficiency of the separation between coal and impurity was shown to be influenced greatly by particle size.

Jan 1, 1950

By Cornelius F. Kelley

EVERY man connected with the mining industry should take a significant pride in the fact that he belongs to an industry and to a profession that, from the beginning, has been constructive. The miner digs his ore and he gives the metal to art, to industry, and to commerce. The nature of our business is destructive only in that we deal with a wasting asset. That should be a source of great pride to those who belong to the profession. But unfortunately, the product of our mines, our smelters, and our re- fineries does not always go to constructive purposes. There are times when, in the administration of the affairs of men, our product chiefly goes to purposes which are destructive. When we look upon the panorama of horror that is being enacted throughout the world today, we wonder whether any effort toward the development of civilization and culture and education and well-being has been worthwhile. We are appalled to see the things that have been developed, through the application of science, toward progress and efficiency, now used for the catastrophic destruction of those things which are the most valuable that man has built. We must find hope that this is but an episodic thing; that it must, in the infinite wisdom of the Almighty, usher in a period of peace and progress, of civilization and development that will make man's existence upon earth worthwhile.

Jan 1, 1941

By H. -F. Krausse

Roof failures in underground coal mines are related to the lithology and geologic structure of the roof. There are two distinct suites of roof rock above the Herrin (No. 6) Coal in Illinois, and each has distinctive patterns of structure and roof failure. In black shale-limestone roof areas, roof instability is correlated with thinning of limestone beds and presence of faults and clay dikes. In gray shale roof regions, the prime roof hazards are posed by rolls, shear bodies, and presence of coal or carbonaceous partings in the roof. Most structural features examined are believed to have formed during early stages of sediment diagenesis and compaction. Structural trends and lithologic patterns are strongly interdependent for this reason. In many cases geologic patterns are so complex and locally variable that prediction of roof stability far in advance of mining is difficult. The need for greater flexibility in roof control planning is apparent.

Jan 1, 1979