Search Documents

A spectrochemical procedure applicable to the determination of iron, manganese, and magnesium in titanium metal and to the determination of alloying constituents in three types of titanium alloys is presented. Acid solutions of samples and standards are excited with a spark-type discharge and porous-cup electrode arrangement. The method is particularly applicable for analyzing samples for which a self-electrode method cannot be used. Calibrations are accomplished with synthetic standard solutions, resulting in a primary method that makes calibrations based upon results of other analytical methods unnecessary. Replicate determinations are reproduced to within 5 percent, and the average percentage deviations from reliable chemical values are less than 6 percent. The method can be extended readily to determine additional elements that are similarly soluble and have similar spectral sensitivities. It also can be used as a starting point to establish standards for a direct sparking procedure for analyzing titanium alloys. In view of the absence of established reliable analytical methods in the titanium industry, the spectrochemical method described here should prove to be a timely contribution.

Jan 1, 1956

By Reeves I. And Farquhar J, Pearce S

The irregular shape of the Rosebery orebody, coupled with the inconsistencies in grade over short strike lengths, has meant stoping blocks have had to be small to combat dilution and stability problems. In the past, each lens was divided into regular block sizes and developed up to five years before production commenced. There were two major drawbacks to this practice; firstly, existing development deteriorated over time therefore requiring rehabilitation prior to production. Secondly, the pre-determined blocks could not be easily changed to incorporate changes in mining technology or economic circumstances. Bearing these problems in mind, it was evident that any new lens development had to be designed to allow maximum flexibility. The lens being currently developed is J lens. It represents approximately 50 per cent of the current reserves tonnes, and 65 per cent of the zinc metal. Its importance to the mine's future cannot be over emphasised. At its core the lens is up to 25 m thick at grades of over 30 per cent zinc. The practice of dividing the orebody into levels and sublevels, with consequent crowns was no longer acceptable because of restrictions in stope design and potential loss of ore. To assist in the development planning of J lens, a geostatistical block model was applied in long section to graphically represent the lens. Areas of high zinc concentration, as well as zones of uneconomic material were identified by using the model. This has meant that the development could he targeted, enabling stope delineation to occur in the lens without significant ore loss. Because of limited development resources, and the need to bring J lens on-line in the near future, the development strategy has had to focus on 'just-in-time' principles, rather than accessing the whole lens from bottom, and progressing upwards. Tight development schedules have required individual stoping block to be developed on such factors as grade and available tonnes rather than as a vertical sequence.

Jan 1, 1993

By Nan C. Jensen, Oliver Bowles

Stone , the foundation of the continents and the floor of the oceans , is one of the most substantial and enduring of all substances that constitute the material universe . Stone furnished rude shelter for aboriginal man , and through all succeeding ages it has provided a lasting and serviceable structural material . Limestone is one of the most widely used building stones .

Oct 1, 1947

Jan 1, 1953

By F. Sorenson, P. A. Castellarini, F. Garbarino, M. N. Garcia

"Recently, significant efforts to improve productivity from the tight intervals of the Mulichinco Formation within the Sierra Chata Field in the Neuquén Basin have been ongoing. Because conventional high quality reservoirs were being developed in this field, a proper reservoir understanding and completion approach was applied. After developing these high permeability reservoirs, the operator began evaluating the tight intervals and new areas within the field, but a completely different approach was necessary to achieve motivating production improvement.An extensive study to help enhance reservoir understanding and identify key factors controlling productivity of these tight intervals (which tend to be in the range of 5 µD) has been ongoing. Some of the issues discussed in this study are 1) petrophysical review, 2) rock properties calibration, 3) geomechanics understanding, 4) faulting and micro faulting/lineaments description, 5) stimulation and completions review and, 6) understanding key production drivers.As in many other tight reservoir projects, a considerable area of the reservoir must be effectively stimulated during the hydraulic fracturing process to achieve economic productivity. Two critical issues hinder these objectives. First, the low permeability in addition to a pore pressure close to or even lower than hydrostatic are critical characteristics when attempting to flow back the well and clean up fractures. Second, very high horizontal stress anisotropy resulting from a strike slip stress regime promotes the generation of simple planar bi-wing fractures. It is well-known that this fracture geometry will contact much less reservoir area compared to more complex fractures, as the operator would normally intend to create at very low permeability reservoirs.This paper discusses these issues and how they were addressed. A pilot drilling and completion program was initiated during 2012 to validate this study. Key factors include well location relative to formation unconformities, their orientation relative to the far field principal stresses, hydraulic fractures generated, and overall completion design."

Jan 1, 2015

By B. G. Klugh

(New York Meeting, February, 1912). IN a paper before the Institute at Wilkes-Barre, Pa., June 1911,1 Mr. James Gayley discussed the application of this process to iron-bearing materials. The same author2 described the results of operations at the plant at Birdsboro, Pa. The purpose of the present paper is to present further discussion of some technical details involved in the operation of this plant, and of the theoretical and practical relations of this product to blast-furnace practice. Since Oct. 1, 1911, the Birdsboro plant has been in operation at the blast-furnace of the E. & G. Brooke Iron Co. The results have been highly satisfactory, although the material treated, being chiefly the flue-dust currently made by the furnace or taken from the accumulated stock-pile, was excessively high, and yet not uniform, in carbon, so that the desirable control or regularity of the amount of fuel in the mixture treated could not be maintained. Nothing could more forcibly demonstrate the flexibility of the process than the fact that, under these conditions, the sinter produced was, in all cases, of excellent quality. The Dwight & Lloyd process, as such, and its present highly-developed mechanical appliances were described by Mr. Gayley in the paper above mentioned. While the repetition of some particulars will be unavoidable in this paper, it will be confined to features bearing upon the metallurgical principles involved. According to the principle of the process, the finely-divided iron-bearing material to be sintered is intimately mixed with

May 1, 1912

By O. C. Blade

This report on the properties of motor fuels sold through service stations In the United States was made In accordance with a cooperative agreement between the American Petroleum Institute and the Bureau of Mines of the United States Department of the Interior. By agreement with the American Petroleum Institute, identification of the items Is confidential. 1t presents analytical data for 4, 802 samples, representing the products of 117 companies. The samples were collected during December 1954 and January and February 1955. As in previous surveys, the gasolines covered 6y this survey Include those from both large and small suppliers. The data were obtained by laboratories of various refiners, motor manufacturers, and chemical companies and submitted to the Bureau of Mines for compilation, A list of the National Motor-Gasoline Survey reports published during the past 10 years is given on page 5.

Jan 1, 1955

By V. F. Parry, J. B. Goodman

The low-rank coals containing 10 to 50 pet natural bed moisture represent over half of the tonnage reserve of the available solid fuels of the United States, but only about 2 pet of United States coal production is derived from these fuels. Increased utilization of these large reserves will result if the bed moisture can be removed at the mine in high-speed low-cost processes. This paper presents a theoretical and experimental study of the factors affecting high-speed drying of coal dusts. The time required to heat particles of coal is proportional to the square of their diameter, and it is calculated that the probable time in minutes is equal to 6D2. In other words, a 11 a in. coal particle should be heated to drying temperature in 1.5 to 2.0 sec. Likewise, 1/8 in. particles should be heated in about 6 sec. The net heat required to dry subbituminous coal and lignite varies from 240 to 375 Btu per pound, depending upon the moisture removed, and this heat can be obtained from 42 to 61 cu ft of hot gases at 600°F.

Jan 1, 1949

By R. E. Lindstrom, D. J. Bauer

Studies were conducted to assess the potential of naphthenic acid as a fractional extractant for rare- earth mixtures and yttrium in sulfate solution . Naphthenic acid was an effective extractant , and separation factors were favorable in the presence of aqueous phase chelating agents . Addition of EDTA to the naphthenic acid extraction system resulted in average separation factors of 2.2 between adjacent yttrium- group elements , whereas DTPA resulted in average separation factors of 3.5 between adjacent cerium- group elements . EDTA was of value in separating yttrium from the rare- earth elements . Thorium and uranium were preferentially extracted over the trivalent rare- earth elements by naphthenic acid .

Jan 1, 1964

By Leping Liu, Sachin Urade, Li-Ting Chen, Pengbo Chu

This study aims to provide industrial perspectives on the current U.S. metal mining engineering education and areas for improvement. An online survey was designed to seek opinions from the U.S. mining industry. Findings indicated a shortage of qualified graduates from the current U.S. metal mining engineering education system. The qualifications that need to be improved include engineering sciences underlying mining methods, mining design experience, mining feasibility study, the connection between theory and practice, and understanding of the overall mining operation. The survey also identified future desired qualifications, such as the ability to acquire and apply new knowledge as needed and sufficient field experience. Respondents recommended enhancing collaborations between industry and academia.

Oct 1, 2023

La influencia de los estudios de adsorción para el beneficio de los minerales, se relaciona con la flotabilidad de las especies minerales, y la perspectiva que se ofrece para el progreso de la metalurgia de concentración. Por ello, el objeto de la investigación se basa en la realización de tales experimentos como búsqueda del dominio de la clase de fenómenos fisico-químicos. Dentro de los métodos usuales de determinación de xantatos por yodo, se buscó hallar la concentración por medio del descenso de la adsorción, para determinar la máxima cantidad de reactivo y encontrar el más adecuado para el mineral. Empero, se reparó que a mayor concentración de colector, se genera mayor adsorción. Asímismo cuando se añade el xantato sobre el mineral con poca agua, la cantidad de reactivo adsorbida es superior, justificándose la ventaja que en procesos industriales significaría acondicionar después del espesamiento. En cuanto a la adsorción de galena oxidada, se observa que mezclando este mineral con un sulfuro de zinc, disminuye la adsorción. Posteriormente se ve cómo la superficie oxidada de la galena, puede alterarse por medio de reactivos, variando el grado de adsorción para los diferentes reactivos colectores de flotación. Finalmente se infiere que la realización de las pruebas pretenden determinar principalmente cuál es el reactivo más adecuado más adecuado para una galena determinada.

Jul 20, 1957

By Osvaldo A. Bascur

Standards and Technology for bringing information at the desktop has greatly evolved in recent years. The benefits to be realized depend on how these new tools are embraced at the performer level. A key operating challenge is to ensure collective effort is geared towards the most efficient achievement of identified operating and corporate objectives. Presentation, application and data repository modular software are emerging in successful client server applications. The industrial desktop emerges as the new tool for continuous improvement and innovation in industrial operations. Here, process information, reliability maintenance, process simulation, production schedules, performance monitoring are integrated using Microsoft enabling tools at the desktop. A workflow model is presented to assist in implementing a strategic information system in metallurgical plants.

Jan 1, 1996

By Brenton Cook, Nate Long, Larry Applegate, Aaron K. McCain

"The Northgate Link Extension project is the third phase of the Sound Transit master plan to extend light rail throughout the greater Seattle metropolitan area. When completed, the Northgate Link Extension will extend the existing light rail system north by about 7 km (4.3 miles) from the University of Washington to the Northgate neighborhood. A general overview of the project alignment is provided as Fig. 1. The project was funded by a combination of federal grants and allocations from local taxes. The general contractor on the project was JCM Northlink LLC (JCM), a joint venture between Jay Dee Contractors, Frank Coluccio Construction Company and Michels Corp. SoilFreeze, Inc. was retained as a subcontractor to provide ground freezing design and construction services.The project involved the construction of two parallel 5.5-m, 25-cm (18-ft, 10-in.) (inside) diameter tunnels using earth pressure balance (EPB) tunnel boring machines (TBM) and precast segmental concrete tunnel liners. The two tunnels maintained roughly the same elevation along the alignment and were spaced roughly 12 m (40 ft) apart (centerline to centerline). A total of 23 cross-passages connecting the two tunnels were included at approximate 244-m (800-ft) intervals. Cross passage excavations were elliptical in shape with dimensions of approximately 5.6 m (18.5 ft) in height and 5.3 m (17 ft) in width. The cross-passages were 5.8 to 6.1 m (19 to 20 ft) long as measured between the exterior of the tunnels at springline elevation. Cross passages were intentionally located directly beneath public right-of-ways thus avoiding buildings. Many of the cross passages were located beneath narrow roads in residential neighborhoods with mature vegetation, existing utility structures and piping and limited parking areas. Excavation and support for each cross passage was completed using the sequential excavation method (SEM).The subsurface soil and ground water conditions at the cross-passage locations were described in the Northgate Link Geotechnical Baseline Report (GBR) prepared by Jacobs Associates and the Northgate Link Geotechnical Data Report (GDR) prepared by Shannon and Wilson, Inc. Soils along the project alignment were glacially overridden and characterized as very dense or hard. Subsurface soils consisted of cohesionless sand and gravel (CSG), cohesionless silt and fine sand (CSF), cohesive clay and silt (CCS) and till and till-like deposits (TLD)."

Dec 1, 2018

By Mansoor Barati, Shaghayegh Esfahani

"The slag from extraction of ferrous and non-ferrous metals is a potential heat source which if treated properly can contribute to recovery of a significant amount of energy. The waste heat of slag may be used to generate steam, synthetic fuel gas, or electricity. Although several technologies have been investigated for this purpose, very little has been achieved in terms implementing the technology in industry. In this article, the development and application of various granulation techniques are reviewed and the methods to recover energy from granulated slag are discussed.IntroductionEvery year, more than 422 million tons of slag is being produced around the world as a by-product of the metal manufacturing at temperatures of up to 1300-1600°C [1, 2]. Currently slags are either disposed of or treated by processes such as granulation. Through the granulation process, most slags can be converted into a material which may be fully used as a cement feedstock. Conventional cement production is an energy intensive process with large emissions of CO2; therefore, the replacement can both be energy saving and environmentally friendly. However, for this purpose, the slag should have what is known as a “glassy” content (i.e. it should be amorphous) which requires rapid cooling rates that are not easily achieved due to the very low thermal conductivity. The main challenge in all these processes is to granulate the slag at a high cooling rate while the heat is also being recovered."

Jan 1, 2012

The research, development and testing of a Blast Control Plug (U.S. Pat. #4,754,705) funded by the U.S. Department of Energy is described. The plug's function is to improve blasting efficiency through the enhancement of stemming effectiveness and thereby reduce drilling and blasting costs. The plug comprises a solid unit placed in the blast hole within the stemming column above the explosive. It is designed for use with back filled drill cuttings or any other suitable material The research and development program comprised the testing of the plug in small diameter holes in competent rock for both bench and crater blasting configurations and full scale field trials in multiple hole and row blasts using blast holes of from 76 to 387 mm in diameter. Test measurements included stemming displacement and velocity, face movement and extent, peak air over pressure and ground surface peak particle velocity. Data acquisition equipment included a Spin Physics SP2000 high speed video motion analysis system, and acoustic and seismic monitoring units. Substantial reductions in stemming ejection velocity or ejection elimination were achieved whilst reducing stemming length by up to 35% over conventional practice. Peak air blast pressures were also reduced by between 8 and 25 dB. A strong inverse relationship between rock face movement and stemming ejection velocity was found. The implications of the importance of stemming effectiveness in blasting and computer blast simulation is also addressed.

Jan 1, 1990

By Heretiano Dalmacio Sampaio Junior

Neste trabalho será apresentado o detalhamento das atividades necessárias à realização dos serviços de recuperação de eixos comuns de acionamento de grandes equipamentos mecânicos. Apesar do ideal ser o emprego de eixos sobressalentes para substituição do eixo fraturado, dando continuidade aos trabalhos sem interrupção dos serviços, as técnicas demonstradas neste trabalho mostram ser viável tecnicamente e economicamente a recuperação de eixos fraturados por soldagem.

Aug 8, 2018

By Norman Carmichael, John Kiddie

The problem of transportation in the Clifton-Morenci district of Arizona has been one of peculiar difficulty and consequently has been an important factor in the cost of mining and treating the ores produced. From the crude beginning made over 50 years ago, many changes have been necessary to keep pace with the increased output of copper. A heavy-duty haulage system has developed on the original 20-in. track gage to meet the existent metal-mine conditions. Topography The transportation difficulties of this district may be readily appreciated from the relief map shown in Fig. 1. The northern half of the district is high mountainous country and there is a general but irregular drop toward the southern part, where the country, although still rugged, is in reality a great sloping plain. This is cut by numerous ravines from which the waters, in the rainy season, discharge into the channel of the San Francisco River. A chasm, 1000 ft. deep, has been eroded through the center of the district by Chase Creek, which is flanked by high irregular mountain masses, notably Copper Mountain, American Mountain, Coronado Mountain, and Markeen Mountain. The latter rises 2300 ft. above the bed of the creek, The San Francisco River has also cut a deep channel, though it is somewhat broader than Chase Creek. Eagle Creek traverses the extreme southwest portion of the area, where it has carved picturesquely through vast volcanic flows. Faulting has left its mark upon the topography of the district by adding to the irregularities caused by erosion. Strong faults occur at the Coro-

Jan 1, 1924

By Thomas Varley

Data on the consumption of reagents used in flotation during the years 1923 and 1924, in metallurgical plants in the Unites States, are presented in this paper. Two previous reports Lave been issued by the Bureau of Mines on consumption of oils and other reagents used to flotation - namely, "Statement of Flotation Oils," by O. C. Ralston, issued in 1913, and Serial No. 2203, "Consumption of Reagents Used in Flotation," by Thomas Varley, for the year 1919, issued in January, 1921.

Jan 1, 1925

By R Shelton

The Big Wainihinihi River and tunnel are located on the western side of the Southern Alps of New Zealand within the active Alpine Fault zone, which marks the boundary between the Pacific and Australian Tectonic Plates. The tunnel was built over 100 years ago to supply water for gold mining, but it now conveys water from a high-energy intake to a canal that supplies three of TrustPower’s hydro-electric power stations with a combined installed generating capacity of 10 MW. Part of the tunnel passes through an unstable 50° schist slope, which fi rst suffered a wedge failure in the 1929 Arthur’s Pass Earthquake and was reinstated in the mid-1970s for hydro generation. In 2008, TrustPower’s monitoring system showed that the wedge failure had remobilised and that urgent remediation was required.Harker Underground Construction (Harker) was awarded a design-build contract to restore the tunnel to service by tunnelling a new central section. Their geotechnical engineers, Peters and Cheung, reviewed the tunnel’s stability and proposed a new, safer tunnel alignment, deep behind the failure wedges. This work was based on their failure model, cost-benefit studies, and engineering geology completion mapping at the time of re-opening.Construction innovation was an important factor in ensuring the project’s success, as were detailed geological and geotechnical information, a robust methodology, strong client relationship and planning. To suit the varying rock conditions and restricted space, Harker combined a traditional drill-and-blast method with light-weight modular steel sets and timber supports to reduce construction costs and mitigate support risk. To make material handing easier in the tight conditions, a special electric locomotive was designed and built and blasting confi gurations were adapted to suit varying rock conditions in the highly fractured schist.The isolated site meant interesting and unexpected challenges, particularly communications and resources (both human and material). Despite that, the project was completed within budget, on schedule, and with no lost-time injuries.

Mar 8, 2011

By N. S. Aouad

"Gaseous explosions are one of the most hazardous incidents in process and mining industries. Experimental research in this area is shown to be high risk and expensive. Computational Fluid Dynamics (CFD) techniques are reasonable alternatives to experiments; specifically when testing large scale gaseous explosions such as methane explosion in underground mines. The dimensions of a confined space where explosions could occur vary significantly. Thus, the scaling effect on explosion parameters is worth to be investigated using CFD tools. In this research paper, the impact of scaling on the explosion overpressures is investigated by employing two scaling factors. These two factors are the Gas-fill Length scaling factor (FLSF) and the Hydraulic Diameter scaling factor (HDSF). The combinations of eight HDSFs (1, 2, 4, 8, 16, 32, 64, and 100) and five HDSFs (0.5, 1, 2, 4, and 8) will cover a wide range of space dimensions where flammable gas could accumulate. Experiments were conducted to evaluate the selected premixed combustion and turbulence models. Large Eddy Simulation (LES) turbulence model was used because it shows accuracy compared to the widely used Reynolds’ averaged models for the scenarios investigated in the experiments. Researchers also simulated methane explosions in both deflagration and detonation regimes using different numerical schemes. Three major conclusions can be drawn from the simulation results. (1) The overpressure increases with both FLSF and HDSF within the deflagration regime; (2) in an explosion duct with length to diameter ratio greater than 54, detonation is more likely to be triggered for stoichiometric methane/air mixture; (3) overpressure increases as an increment hydraulic diameter of a geometry within deflagration regime. INTRODUCTION The most typical category of gaseous explosion accidents is methane explosion accidents in the mining industry. It normally leads to significant economic loss and massive amount of casualties (McPherson, 1993). It could occur in unconfined spaces, such as combustion due to flammable gas leakage, as well as confined spaces, such as inner-combustion in process equipment and methane explosions in airways of underground mines. Gaseous explosions in confined spaces are more intensive compared to unconfined spaces provided that the total energy of explosives is the same. In addition, explosion characteristics are also affected by the geometry of a selected confined space. The size of confined spaces commonly encountered in process and mining industries could differ as much as an order of four (Catlin & Johnson, 1992). A better understanding of the scaling effect on gaseous explosions could contribute to explosion mitigation and prevent operation activities within high risk regions. This research paper has investigated this scaling effect and its impact on explosion propagation. The approach to investigate explosions is either experimental or numerical. Large scale explosion experiments are often costly and dangerous (Catlin, 1991; Zhang, Pang, & Zhang, 2011). Lab scale experiments and numerical methods are common alternatives. However, it is not yet clear if the findings in lab scale experiments can be used to represent the explosion characteristics or not. On the other hand, CFD modeling has been used to simulate chemical combustions and, thus, can be used to evaluate the scaling effects in methane explosions."

Jan 1, 2015