Search Documents

By Z. T. Bieniawski, José Miguel Galera, Benjamín Celada

TBM case histories from over 400 tunnel sections are analyzed presenting a comprehensive application of the Rock Mass Excavability (RME) index (Bieniawski et al.2006). The paper introduces two new adjustment factors, called the Factor of Tunnel Length and the Factor of Crew Effectiveness, which were established to represent more realistically the interaction of the rock mass characteristics, the TBM parameters and the performance of the crew operating the machine. A new correlation is provided for predicting the average rate of advance of double-shield TBMs working specifically in the double-shield mode.

Jan 1, 2007

By Rick Deschamps, Brian Barkauskas, Aled Hughes, Abigail Stein

In central Washington, six miles south of the small town of Vantage, the flow of the Columbia River is harnessed by the Wanapum Dam which is part of the Priest Rapids Hydroelectric Project owned and operated by Grant County Public Utility District (GCPUD). Extending more than 8,300-feet from bank to bank, the dam includes left and right earth embankments, left and right concrete gravity sections and a 10-unit powerhouse. Adjacent to the right embankment is a concrete gravity spillway featuring radial gates measuring 50-feet-wide and nearly 70-feet-high. In the early 1960’s when Wanapum Dam was built, these seven-story spillway gates were the highest in the world. In late February 2014, 50-years into its service life, during a routine maintenance inspection, observant workers noticed a slight misalignment in the roadway deck curbs and handrails located on top of the spillway. Further survey and inspection efforts uncovered a 65-foot-long by two- inch-wide crack that spanned the full length of Monolith 4. On discovering the extent of the damage, GCPUD initiated immediate drawdown of the reservoir to relieve pressure on the spillway monoliths. Wanapum Reservoir and the areas directly downstream of the dam were immediately closed, boat ramps and inlets were left completely dry, campsites were closed and boating activity was banned on the lake until further investigations and remedial procedures were in place and completed. An extensive root cause analysis ultimately led to the conclusion that errors in the initial design calculations and late changes to the final spillway design led to a condition that generated tensile stresses in the concrete at the upstream face, which over a period of 50-years resulted in the formation of a crack along a horizontal lift joint located about 85-feet below normal pool elevation. Further analysis showed that, although visible distress was found at Monolith 4, there was nothing preventing this issue from happening at other locations along the dam spillway. Although no visible cracking was found in the other monoliths, repair procedures for Monolith 4 would have to be replicated at the remaining monoliths.

Jan 1, 2018

By D. E. Calisaya, É. Poulin, A. Desbiens, R. del Villar, A. Riquelme

"A 15 cm diameter by 732 cm height, fully automated pilot column was installed in the Agnico-Eagle’s Laronde concentrator (Québec), for evaluating the performance of newly developed sensors and advanced process control algorithms. For eventual comparison purposes, the pilot column is continuously fed with the same slurry feeding the copper-circuit third cleaner column. It is equipped with electrical conductivity-based sensors for estimating the three variables used in the multi-variable control algorithm under evaluation: froth depth, fraction of wash water underneath the interface and gas hold-up. Froth depth is regulated using a PI controller while a predictive controller is formulated as the minimization of the tracking errors of gas hold-up and bias rate, keeping several operating constraints between their practical upper and lower limits. In particular, an unreachable high set point of gas hold-up can be selected in order to maximize the bubble surface area available for particle collection, while maintaining bias rate above a minimum value required for froth cleaning. The proposed strategy may indirectly help optimizing flotation column operation by using these secondary variables, without the implementation of a real-time optimization layer.INTRODUCTION Flotation columns have already been used for more than 30 years, mainly in cleaning stages, as a result of their froth washing capabilities. Despite their widespread usage, the measurement of some pertaining variables and their use for automatic control is rather scarce. Among the most important variables directly related to the process metallurgy (concentrate grade and recovery), froth depth (hf) is the only one normally monitored and controlled. Even though commercial sensors are available, gas hold-up (eg), a variable directly related to concentrate recovery, is seldom measured and never controlled. Another important variable, bias rate (Jb) responsible for concentrate cleaning, is simply not measured at all, as there is no commercial sensor available. Therefore, besides froth depth, continuous monitoring of process variables is limited to flow rates (gas, feed, tailings, wash water), i.e. to manipulated variables. Some new available sensors have been industrially tested, e.g. the Sonar-TracTM for eg (O'Keefe, Viega & Fernald, 2007) and the McGill hold-up sensor (Tavera & Escudero, 2002). Others, for bias rate and frother concentration, have been successfully validated at laboratory scale by Laval’s LOOP researchers (Maldonado, Desbiens, del Villar & Chirinos, 2008b; Maldonado, Desbiens, del Villar & Aguilera, 2010a). Some devices have been extensively used for monitoring bubble size and space distri-bution, e.g. McGill bubble viewer (Gomez & Finch, 2007) and others."

Jan 1, 2012

By Adrian Moore, John Wilson, Alan Richards, Emad Gad

Project C9040 – ‘Structure Response to Blast Vibration’, funded by the Australian Coal Association Research Program (ACARP), involved the investigation of the structural response from blast vibration of three houses of brick veneer construction subject to a wide range of ground vibration levels. This paper summarises the findings of a house subject to vibration levels up to 220 mm/s (8.7 in/s). Damage attributable to blast vibration was not observed until vibration levels exceeded 70 mm/s (2.8 in/s).

Jan 1, 2003

By Helen Francis

Over the last decade, lower ore grades and deeper mine environments have demanded that mining companies develop new technologies (tools and processes) to ensure a mine?s economic sustainability. At Inco Ltd., this demand has lead to the focus of technological development within the area of automation. Delineation (Drilling and Interpretation) is a key step in the determination of ore grade and location and therefore was chosen as a priority area for enhancement through automation. Focusing on the tools (the diamond drill) automation, significant benefits have been consistently achieved in terms of productivity, process efficiency, operational safety, cost reduction, component life cycles and machine reliability. It is suggested that optimum benefits have yet to be achieved, and will not be achieved until the human aspects of automation have been properly addressed. Since project inception, the human aspects of automation were recognized as critical to the success of the diamond drill automation project. However, it was only upon the installation of the Automated Diamond Drill in the field and its continued use on a daily basis that this issue received due attention. The human aspects of automation can be broadly addressed as economic, physical and psychological. This paper, with examples from the field, will discuss the human aspects of automation in each of these areas. The paper will draw from observations and experiences acquired throughout this project and recommend implementation strategies that should be utilized in future automation projects to enhance both the acceptance of automation and the success of the automated process itself.

May 1, 2002

By Fred W. Snow

This paper describing the mining practices at the Magma mine, Superior, Ariz., is one of a series being prepared by the Bureau of Mines on mining prac¬tices, methods, and costs in the various mining districts in the United States. At present (1929) practically all the mineral production in the Superior district is from the Magma mine of the Magma Cooper Co. The ore is mined for its copper but contains associated silver and gold. Both direct smelting ore and ore of concentrating grade are produced. The mining methods now in use at the Magma mine were adopted or developed as knowledge was gained of the physical condition of the ore bodies and the inclosing formations; the wall rock is soft and crushed and the ore is relatively hard. In general, existing methods have been adapted to fit local conditions, but some of the mining practices used were originated at this mine. Most of the ore is mined by a combination of rill stopes and pillar stopes. The pillars are extracted by underhand mining.

Jan 1, 1929

By S. G. Malghan, J. P. Van Dillen

Introduction Some uranium minerals are paramagnetic and hence are amenable to concentration by high gradient magnetic separation (HGMS). This paper describes effects of the HGMS parameters-pulp velocity, field strength, matrix loading, and magnetic field gradient-on the product recovery and grade. Unsatisfactory separation of uranium minerals by HGMS is related to ore-specific properties, such as lack of liberation, fine dissemination of uranium minerals, uniform distribution of magnetic minerals throughout the ore matrix, and interference of fine-sized slimes. Experimental techniques to identify and resolve some of these problems are outlined. HGMS of Uranium Ores The mechanism by which uranium minerals are attracted to a magnetic field is either due to its magnetic susceptibility or its association with other minerals that are magnetic. Data on magnetic susceptibility of uranium minerals are scarce. The only reported data are for uraninite at 2360 X 10-6 cm3/mole. Povarennykh (Andres, 1976) concluded that the magnetic properties of minerals depend on: • Structure of the outer electron shell in a mineral with electropositive atoms; • Valence of the atoms; • State of the chemical bonds; • Type of coordination; and • Proportion of magnetic atoms (Fe, Mn, Cr, and Ni) in the composition of the mineral. However, information on the magnetic susceptibilities of the constituent atoms of a mineral alone does not suffice for evaluating the mineral compound as a whole. Most often, uranium minerals can be beneficiated by HGMS if they are associated with other minerals that are magnetic. This appears to be a more predominant mechanism by which the uranium minerals are beneficiated. Experimental A Sala-HGMS (Malghan and Subramanian, 1981), model 10-15-20, separator was used in the experiments. The matrix material-ferromagnetic stainless steel in the form of expanded metal or steel wool-was packed into a 38-mm (1.5-in.) diameter by 360-mm (14-in.) long canister. The matrix material occupied only a 150-mm (6-in.) length. The experimental set-up and slurry flow direction are described elsewhere (lannicelli, 1976). The response of uranium ores in the HGMS was studied by feeding well-dispersed slurry at 10% solids and examining the influence of process variables on selectivity and overall uranium recovery. The chemical and mineralogical characteristics of the ores under study are presented in Table 1.

Jan 12, 1983

By Jocelyn Bouchard, Claude Bazin, Sami Makni, Rolando Quispe

"Finely disseminated minerals in ores require intensive size reduction to achieve sufficient liberation for the subsequent concentration process. The use of small grinding media in conventional ball mills as a replacement for the usual 2.5 to 3.8 cm balls (1.0 to 1.5 in) produces a finer size distribution at a lower power drawn by the mill motor. However, the conditions ensuring a successful application of using small media for fine grinding are still not fully understood and some plants faced issues to keep the newly introduced steel charge inside the mill during industrial trials. The retention conditions of small media are investigated in this paper using a continuously operated 40 x 40 cm laboratory grinding mill. The tests assess the effect of the steel charge level, the slurry solids concentration and the feed rate on the rate of ejection of the grinding media. The dominant variable is found to be the filling of the mill with the grinding media, followed by the mill feed rate. Results show that increasing the slurry solids concentration within a grinding mill may be favorable for the retention of the media inside the mill.IntroductionProcessing of complex ores often requires the use of fine grinding to liberate finely disseminated minerals. Grinding requirements for a P80 of less than 0.02 mm are not uncommon, and different grinding mills are available for such application (Leonida, 2014; Pease et al., 2006; Davey, 2006; Orford et al., 2006; Nesset et al., 2006). Even conventional horizontal ball mills charged with of 2.5 cm or larger grinding media can be used for fine grinding. However, simulation (Orford and al., 2006) and plant observations (Alves and L-Bouchet, 2005; Brisette, 2010; Brisette and Roman, 2012) demonstrated the advantages of using smaller grinding media in terms of size reduction and energy consumption."

Jan 1, 2015

By Don Z. Painter, Gordon F. Revey

Frontier/Traylor Joint Venture is presently constructing a section of the Tri-County Metropolitan Transit District of Oregon's (TRI-MET) Westside Light Rail system. This new section will extend Portland's existing transit system to the western suburbs of Beaverton and Hillsboro. The drill-blast excavations at this project include 10,000 feet of 20 foot tunnel, 18 cross passages, three shafts, an underground railway station, and a U-wall open cut. From a blast designer's perspective, this job has been extremely challenging. Blast vibration is limited to 0.5 ips at 200 feet or at the nearest structure, and airblast is limited to 129 dB -- linear peak and 96 dB -- C scale. The tunnels pass under heavily built up areas and have top of tunnel to surface cover distances as low as 70 feet. Surface blasting in the 26,000 cubic yard U-wall excavation was limited to five short nighttime periods due to its proximity to the very busy highway 26.

Jan 1, 1995

By R. N. Gow

The presence of enargite (Cu3AsS4) is problematic in gold processing because it is environmentally hazardous due to its arsenic content but also because it is double refractory causing both cyanide and oxygen consumption to increase. Selective leaching and treatment of the arsenic would prove advantageous prior to applying conventional gold leaching methods. The reactivity of enargite samples from Butte, Montana and Quiruvilca, Peru were spectroelectrochemically studied under alkaline conditions, pH range of 8-13, using Raman spectroscopy and cyclic voltammetry. Raman spectra of the surface were collected during and after voltammograms were potentially cycled in order to determine and compare surface species against theoretical EH-pH diagrams determined from mass-balanced thermodynamic calculations using StabCal software. Under slightly oxidizing conditions, covellite (CuS) peaks were found in a short matter of time, above ~100mV vs SHE for pH 9-13, suggesting arsenic leaching specifically occurred. At longer conditioning times, elemental sulfur was observed and tended to passivate the surface. The presence of sulfur suggests that copper was eventually leached. By operating above pH 12, under slightly reducing conditions near -300mV vs SHE, arsenic can be selectively leached as thioarsenate (AsS43-) or thiosulfate (AsO43-) without sulfur formation.

Feb 27, 2013

By d&apos, E. Appolonia

A construction project is successful when all parties contributing to it are winners. It is not a success when there are winners and losers. Con­tractors, engineers, suppliers and equipment developers, and especially owners, each can contribute and benefit from a revaluation of attitudes and contacts from planning to final payment. The Deep Foundations Institute was initiated with this as its major purpose. The help of educators is essential to promote this with the next generation. The Association of Soils and Foundations Engineers has developed guides for "Mediation Arbi­tration of Construction Contracts."

Jan 1, 1985

By Geoffrey Hughes

The Narragansett Bay Commission (NBC) is a regional sewer authority that serves ten communities in the Providence, Rhode Island metropolitan area. From 1992 to 1999, the NBC developed a comprehensive facilities plan to abate Combined Sewer Overflow (CSO) pollution in the Upper Narragansett Bay. The plan underwent many major evolutions during this period, most notably the addition of a stakeholder?s process by which NBC demonstrated a site-specific plan to control the pollutants and meet water quality standards. The favored solution consisted of deep tunnel storage with treatment at existing wastewater facilities that had been recently upgraded. In 1999, a final plan was accepted which included two tunnels, five CSO interceptors, twelve sewer separation projects, a wetland facility, and a wastewater treatment facility upgrade. The program is to be constructed over 20 years in three sequential phases (Figure 1). Phase I of the program includes a 4,963 m (16,284 ft) long, 7.9 m (26 ft) diameter, 70.1 m (230 ft) deep storage tunnel; seven drop shafts with connecting adits; ancillary facilities; and a pump station. Construction of Phase I began in 2001 and is expected to be operational by October 2008. This paper focuses on design and construction of the Fields Point Tunnel Pump Station (FPTPS)located at the south end of the main spine tunnel. A189 Ml/day (50 MGD) pump station is required to lift CSO flows from the tunnel to the Fields Point Wastewater Treatment Facility (FPWWTF). The pumps are to be housed in a 35.6 m × 18.6 m ×20.7 m (117 ft × 61 ft × 68 ft), 91.4 m (300 ft) deep cavern excavated in a complex meta-sedimentary rock of the Rhode Island Formation, and connected to the surface by 9.7 m (32 ft) and 3.4 m (11 ft) diameter shafts. Factors which influenced selection of the size, configuration and location of facilities included the preferred arrangement of pumps, critical aspects of site geology, and estimated cost. Technical and value engineering reviews also affected the final design. Following Notice to Proceed (NTP), concerns were raised by the contractor regarding constructability and design. Additional geotechnical investigation and independent engineering review were employed to validate the design assumptions. The cavern was successfully excavated and sup-ported in rock, completed on schedule and within budget in 2005. In 1992 the NBC retained Louis Berger Group (LBG) as Program Manager (PM) for the CSO Abatement Program. LBG thereafter formed a design team including: Jacobs Engineering Group(JEG) as the designer for underground structures and near surface collection facilities; Black and Veatch(B&V) to design the pumping system and associated facilities; Haley and Aldrich (H&A) to oversee the geotechnical program; and Malcolm Pirnie to design the system-wide instrumentation and control system. Construction management, resident engineering, and inspection services were provided by the joint venture Gilbane/Jacobs Associates (G/J).

Jan 1, 2008

By R. T. Stain

Dynamic methods of load testing piles using a drop hammer to generate the input force have been in use for many years. These systems are based on the wave equations developed at the Case Institute of Technology, Cleveland, Ohio in the late 1960's and are well documented. Such tests are generally restricted to preformed driven piles, the driving hammer being a convenient means of generating large input forces. In 1979 the CEBTP (France) was sponsored by the FNTP (Fédération Nationale des Travaux Publics) to undertake research into existing classical methods and to develop a test that would be equally applicable to bored cast in place piles. The result of this research programme is a methodology known as SIMBAT, and which was included in a series of class A prediction trials in Belgium in 1987 (Refs 1 & 2, Paquet 1987, 1988). The purpose of this paper is: a) to examine the type of 'dynamic'/'static? load test correlations that can be obtained. b) to highlight the differences between the classical' methods and the 'SIMBAT' technique.

Jan 1, 1989

By Botelho Junior, Amilton Barbosa, Denise C. R. Espinosa, David B. Dreisinger

Copper and cobalt can be found on nickel laterite ores, and cobalt can be found also on copper ores, and many contaminants such as iron, aluminum, and magnesium are associated with these ores. In hydrometallurgical process, a purification step is necessary after leaching due to the presence of these impurities. Chelating resins are more selective for some metals than others, making them more efficient than cationic resins. This overview discusses chelating resin applications to recover copper, nickel, and cobalt from mining process and mining tailings and the effect of contaminants in leach solution. Chelating resins with iminodiacetate functional group can be used for selective copper recovery, and both iminodiacetate and bis-picolylamine resins are highly selective for nickel and cobalt. Chelating resins with the same functional group can have different performances on the kinetics of loading, because of variations of structure, the density of functional group, and degree of cross-linking. This article reviews commercial chelating resins that can be applied in leach solutions with different compositions, and also possible innovations for uses of chelating resins to recover metals from mining process and mining tailings.

By Lei Pan, Venkata Atluri, Xuming Wang, Yuesheng Gao, Jan D. Miller

The wetting characteristics and water film stability at the talc surface have been studied, particularly the effect of polysaccharides such as guar gum, starch, and dextrin. Talc is a gangue mineral in the flotation of base metal sulfide ores, precious metal sulfide ores, and platinum group metal (PGM) sulfide ores. Talc surfaces were investigated using surface analysis techniques including atomic force microscopy, high-speed video bubble attachment measurements, and wetting film stability measurements using a synchronized tri-wavelength reflection interferometry microscope (STRIM). In the presence of polysaccharides, there is a significant increase in bubble attachment time at the talc surface, but only a slight change in contact angle, which suggests that polysaccharide depression of talc is due primarily to the slow rate of bubble attachment and not due to a change in contact angle. The critical rupture thickness (hc) for a hydrophobic talc surface was found to be 56 nm, while the hydrophilic phlogopite surface of similar structure has an equilibrium film thickness (he) of 25 nm. At low polysaccharide concentrations, the wetting films formed on the talc surfaces were unstable, but at high concentrations the wetting films became stable with similar thickness values as the critical rupture thickness, and bubble attachment did not occur. However, it was found that the critical and equilibrium film thickness values do not change significantly with the polysaccharide type or concentration. The results from this research help us understand further details of film rupture and displacement during bubble attachment.

By Harumasa Kurokawa

Since the initial start-up, the Toyo Smelter & Refinery has been operating in harmony with the ambient environment, and improvements have been implemented with technologies specifically developed for further protecting the environment. Toyo Smelter & Refinery is now planning to increase the copper production capacity from 280,000 tpy to 450,000 tpy, over a period of several years. In 2003, the first step of this smelter expansion and modernization plan was implemented. The production capacity of the P-S converter was increased dramatically, as it became possible to operate under a ?2 hot-2 blowing? schedule. In 2005, an additional converter will be installed, in order to allow operation under a ?3 hot-2 blowing? schedule. This report will describe the technical improvements on the P-S converters, as well as describe the Toyo expansion program and discuss the technologies applied to the fugitive gas collecting system.

Jan 1, 2005

By G. Gaidajis, K. Angelakoglou

The development of a tool for assessing the environmental sustainability of mining facilities is described in this study. The tool is based on the analysis of basic components of the examined system, i.e., the quantities of the incoming materials and outgoing wastes, their hazardousness and scarcity, the utilization of water and energy resources, and the biodiversity. The developed tool provides both qualitative and quantitative assessment of the environmental performance of a mining facility in a broad time scales (past-present-future) and is easily applicable from non environmental experts. Moreover, relative software is developed to further support the application of the methodology. The implementation of the tool is expected to lead to an improved understanding of the environmental performance of a mining facility and more importantly identify the areas of significant environmental concern. However, based on feedback from industries, a number of shortcomings of the approach have been identified so far and are presented, indicating further actions for the advancement of the proposed tool.

Jan 1, 2011

By R. J. Anderson, A. V. Castelli

In 1986, United States' barite production fell 48.9%, consumption - sold or used by grinding plants - was off 47.3%, and imports were down 63.8%. Meanwhile, world mine production decreased 29.6%, according to the US Bureau of Mines. However, value of US-produced barite FOB mine increased 46.51%, according to USBM figures. The declared value CIF US port of all imported unground barite decreased from $41.94/t ($46.23 per st) to $39.02/t ($43.01 per st). Nevada continued to be the leading US producer of barite with 69% of the total. It is followed by Georgia, Missouri, Tennessee, and California. The USBM estimates that 65% of the barite mined was used as a weighting agent in drilling fluids. The remaining 35% was used in the production of barium chemicals and as a filler. Most of the production from Missouri, Georgia, and Tennessee was used in the non-oilfield sector. This sector made up a larger percentage of the US produced barite in 1987 than it did in 1986, increasing the overall value per ton of barite. Barite consumption was at its lowest since 1963. It is estimated that 80% of the barite was consumed in the drilling fluid market. The remaining 20% was used in barium chemicals, glass, and as filler in plastics and paper. The decline of barite used in drilling fluid followed the decline in the average number rotary rigs operating - 964 versus 1968 in 1985. This was the lowest average number of rotary rigs operating since 1971. The non-oilfield market was up 5.3% in 1986. This increase can be attributed to the increased use as a filler in plastics. Imports of crude barite, though down nearly two-thirds, still made up 65% of the barite consumed in the US. China was the leading exporter to the US with 58%, followed by India, 15.4%; Morocco, 11%; Thailand, 5.4%; Mexico, 4.6%; Chile, 3.9%; and Ireland, 1.7%. Less than 1% of the imported ore was used in the nonoilfield sector. Imports of ground barite dropped from 64.4 kt (71,000 st) to 19.8 kt (21,800 st) in 1986. Of this amount, 14.1 kt (15,500 st) were used in drilling fluids in 1986 and the remainder for non-oilfield use. During 1986, more of the grinding plants supplying the drilling fluid market were closed. Dresser Magcobar and IMCO Services, a Halliburton company, formed M-I Drilling Fluids Co. Mine production in the US will probably decrease in 1987 due to the lower cost of imported ore. No significant change is expected in the drilling fluid market. The average number of operating rotary rigs is estimated at 950 in 1987 versus 965 in 1986. The nondrilling fluid markets (chemicals, glass, and filler) will follow the overall US economy. Bauxite and alumina R. J. Anderson, Ohio State University US bauxite production in 1986 dropped to a pre-World War II level, continuing a decline that began a decade ago. 1986 production totaled 450 kt (496,000 st), compared to 674 kt (743,000 st) in 1985. World production of bauxite also decreased in 1986. This reflected the soft market in alumina, aluminum, and related products. Total mine production worldwide came to 79 Mt (87 million st), down from 85 Mt (94 million st) in 1985. For the sixteenth consecutive year, Australian production of bauxite led all other sources. No other country approached the 28 Mt (31 million st) mined in Australia in 1986, despite a 4.4-Mt (4.9-million st) drop in its output from 1985. Other major producers in 1986 were: Guinea 11 Mt (12 million st), Brazil, 6.5 Mt (7 million st), Jamaica, 6.5 Mt (7 million st), and Suriname 2.8 Mt (3 million st). Despite weakness in world demand for bauxite, Venezuela, heretofore an alumina producer, is now pushing development of a new mining venture near the western border of the state of Bolivar. Plans call for barging bauxite down the Orinoco River to the Ciudad Guyana alumina plant, a distance of 650 km (400 miles).

Jan 5, 1987

Characteristics Analysis of a Bastnaesite Rare Earth Mineral for Recovery of Cerium

Sep 13, 2010

By John Capers

•The IME is the Safety and Security Association of the commercial explosives industry in the United States and Canada. •Founded in 1913 •Board of Governors •5 Standing committees- 1. Technical 2. Environmental Affairs 3. Legal Affairs 4. Safety & Health 5. Transportation & Distribution

Jan 1, 2006