Search Documents

By James H. Gary

Data regarding the composition and physical properties of Florida land-pebble phosphate-waste slime are presented, and the feasibility of dewatering and beneficiating the slime by several different methods is discussed. Chemical analyses, electron micrographs, and X-ray diffraction data showed that principal constituents of the slime included quartz, attapulgite, and flaorapatite. Viscosity of the slime changed with pH; thixotropic, Newtonian, and rheopectic states were observed as the pH increased. Use of various flocculating agents was not effective in improving thickening properties of the slime. Dewatering tests using pressure filtration showed that temperature influenced the filtration rate more than pressure; the filtration rate at 165° C was tenfold that at room temperature. Selective flotation of the slime, using two different processes, gave promising results. About 25 pct of the phosphate was recovered in a concentrate assaying 31 pct P205, Other tests demonstrated that the slime could be successfully fractionated at 20-microns using a hydrocyclone. In hydrometallurgical tests about 80 pct of the phosphorus and alumina were chemically extracted from the slime using sulfuric acid. Limited bacteriological studies made of the slime showed that several types of microorganisms were present and grew in the material despite the presence of fluorine-bearing minerals.

Jan 1, 1963

By E. C. Lane

"In a previous paper the Bureau of Mines. 3/ presented in condensed tabular form all analyses of Texas crude oils made by the Bureau up to March 193K. This previous report states;The first Al well in Texas was drilled near Oil Springs, Nacogdoches County, in 1863-67. However, the first oil field of major importance in the State was discovered at Corsicana,Navarro County, in 1895. Since that time the petroleum industry try in the State has spread and grown until today petroleum from Texas is an important commodity in world petroleum markets.Since March 1939 samples of Texas crude oils from many new fields, and some older fields not covered in the previous report, nave been analyzed. Those analyses arc reported in the present paper. The annual production by years from 1896 to 1940, inclusive, taken from the figures in the Bureau of Mines Minerals Yearbook, are given in table 1. Production for 1896-1940, inclusive, totals 6,579,715,000 barrels.Various authors reported upon developments and production in the Texas fields in the Transactions of the American Institute of Mining and Metallurgical Engineers, Petroleum Division, for 1941. 4/"

Apr 1, 1943

By D. W. Bridges, L. Crocker, R. O. Dannenberg

About 95 pct of the beryllium was dissolved from most ore samples by agitation leaching with 600 lb of H2SO4 per ton of ore for 24 hours at 65 ° C and 35 pct solids . Leach slurries generally were viscous , and the limiting pulp density for thorough mixing was about 35 pct solids . Settling of the leached pulp required 0.6 to 0.8 lb of a polyacrylic flocculant per ton of ore leached with 600 lb of H2SO4 per ton , whereas ore leached with 800 lb of H2SO4 per ton required only 0.2 to 0.3 lb of flocculant per ton . Terminal densities of the settled pulps were about 28 and 35 pct solids , respectively , from leaches using 600 and 800 lb of H2SO4 per ton . Vacuum filtration of settled pulps at 15 in . Hg resulted in a filter cake containing 50 to 59 pct solids . Roasting the ore at 500 ° C before leaching increased the limiting pulp density for effective mixing to 50 pct solids . Acid requirements , however , were not diminished , although leaching roasted ore with 600 lb of H2SO4 per ton resulted in densification of settled pulps to about 40 pct solids . Filter cake from leaching preroasted ore contained about 20 pct less water than that from unroasted ore .

Jan 1, 1963

By Ginger S. Evans

This report documents a preliminary hydrologic investigation of an area where longwall mining methods are to be used. The scope of work includes: determination of physical and chemical characteristics of major soil types in the area; determination of physical and chemical properties of surface water bodies; collection of geologic characteristics, including stratigraphy, structure, and detailed aquifer descriptions; collection of 10 years' meteorological data and installation of a weather station; and a detailed ground-water investigation that includes completion of observation wells, aquifer testing, water quality sampling, and analysis using a 3-D computer model. The Trescott model developed by USGS was used to simulate steady-state aquifer conditions. Input data from 8 multiple-completion monitor wells were used to model an area of approximately 10 square miles. Two layers, coal and overburden, were simulated, both confined. Model results showed good agreement with know piezometric data, desaturated areas, and flow from springs. The study area was found to have very low-yield bedrock aquifers with transmissivities ranging from 5 to 320 ft2/day for the coal (depths from 500 to 1,200 ft) and from 499 to 576 ft2/day and fractured sandstone units (depths less than 100 ft). Annual precipitation and recharge are very low, 10 to 11 inches and 0.25 inch respectively. The area has very high relief and large areas of rock outcrop. No perennial streams are present on the site.

Jan 1, 1983

By W. O. Vanderburg

The leasing or tribute system has been an important factor in the development of our metal-mining industry, particularly in the gold and silver mines of the Western States. It has received its widest application in. the early history of many camps and in the last stages of many mines. The system is especially adapted to mining where the ore's occur in narrow veins or are erratically distributed in small bunches or pockets so that selective mining, hand sorting, screening, or hand cobbing is required to produce shipping or milling-grade ore. The leasing system is also applicable to the development of prospects where the owners are unable or unwilling to assume the risks of searching for ore. The virtue of the system lies in the opportunity it affords miners with little capital to get started; at the same time, it rives owners an opportunity to have their property developed at small cost.

Jan 1, 1934

By J. B. McKay

It is the purpose of this paper to present an initial report on the construction and operation of the Fluo-Solid roaster at the property of Campbell Red Lake Mines, Ltd., Balmertown, Ontario. The roaster prepares for subsequent cyanidation the bulk flotation concentrate obtained from four hundred tons per day of gold ore. The mill flow-sheet 'includes jigging and amalgamation; flotation; cyanidation of flotation tailing; and roasting followed by cyanidaition of flotation concentrate plus amalgamation tailing. Overall mill recovery for the year 1950 was 90.2 per cent. Recovery possible by straight cyanidation of this ore would not exceed 80 per cent. The ore contains considerable arsenopyrite and pyrrhotite as well as pyrite, with lesser quantities of nickel, zinc, and copper minerals. The mineralization is for the most part extremely fine. The roaster first went into operation on August 7th, 1949, and at the end of 1950 it had roasted 10,916 tons of concentrate. The average recovery of gold from calcine during that period was 94.86 per cent in the primary stage of calcine cyanidation. The average assay of calcine residue from primary cyanidation for the entire period was 0.37 oz. per ton. Both laboratory tests and plant metallurgical balance calculations indicate a further recovery of approximately 10 per cent of this 0.37 oz. when the calcine residue is again cyanided, in the flotation tailing cyanidation circuit.

Jan 1, 1951

By F. P. Morawski, J. E. Schelske, J. R. Geddes, B. R. Eberts, D. M. Wilson, J. D. Jeffries

"The Griffith Mine is located 200 miles northeast of Winnipeg and is 30 miles south of Red Lake, Ontario. Owned by The Steel Company of Canada Limited and managed by Pickands Mather & Co., it has an annual rated capacity of 1.5 million tons of high-grade iron ore pellets with an analysis of 66.3 per cent iron and 4.5 per cent silica.Development of the mine and construction of the plant got underway in January of 1966 and operations began in February of 1968. The orebodies outcrop on the shore of Bruce lake and run under the lake. The ore in its crude form is a metasedimentary low-grade magnetite and occurs in a highly folded banded formation. The average iron analysis of the crude is 29 per cent and the over-all weight recovery is 32 per cent.In order to mine the portion of the orebody under the lake, the soft varved clay on the lake bottom was hydraulically dredged and a dyke constructed of rock, with till used to provide an impervious seal on the lake side of the dyke, prior to dewatering.Mining is carried out by conventional open-pit tech-niques. Ore dressing is achieved by combining one crushing stage and a two-stage grinding system, with beneficiation by magnetic separation, hydroseparation and flotation. Agglomerating is done with conventional balling drums and pelletizing is carried out in shaft furnaces.Of interest and discussed in detail are the 32-foot autogenous cascade mills ."

Jan 1, 1970

By C. E. Reistle

The generation of steam for drilling operations has visually been accomplished in the past by the use of portable locomotive-type boilers without the aid of auxiliary equipment or advanced for economizing fuel or water consumption. This has been due primarily to the fact that the steam-generating plant of a drilling well must necessarily be of temporary and portable design, and the amount of steam generated has not been considered sufficient to justify the additional expense necessary to obtain more economical operation. However, with the constantly increasing depth to which oil wells are being drilled and the use of larger and heavier equipment, the steam requirements have reached a point where equipment and methods that were previously considered as applicable only to permanent plant installation can be and are being used to a decided advantage by the more progressive operators. As an example of the present-day requirements and the rapidly increasing steam consumption in rotary drilling, a comparison between the requirements during the intensive drilling period in the Seminole end Oklahoma City fields of Oklahoma is of interest. In the Seminole field. There the approximate depth of rotary drilling was 3,500 feet, the general practice was to use three 85 to 90 or 100 horsepower A. P. I. code boilers operating at a working pressure of 175 to 200 pounds per square inch. The fuel end water consumption was approximately 450 to 500 thousand cubic feet of gas and 700 to 750 barrels of water per day. In the Oklahoma City field, where the average drilling depth is approximately 6,500 feet, the general practice is to use either four 100 or 116 horsepower or three 123 horsepower A.P.I. code boilers, operating at a pressure of 250 pounds per square inch. The fuel and water consumption varies from 550 to 750 thousand cubic feet of gas and from 1,000 to 1,500 barrels of water per day.

Jan 1, 1930

By S. A. Shuey

The present industrial practice used to separate aqueous cobalt from nickel is multistage solvent extraction processing. This paper describes a different but simpler treatment technology. The proposed technology has been applied to cobalt/nickel hydroxide intermediate solids produced from the treatment of Electrochemical Machining (ECM) waste sludge, The process consists of dissolving the cobalt/nickel hydroxides in basic cyanide solutions. Cobalt and nickel form aqueous .solution metal cyanide complexes. Nickel can be selectively precipitated from the solution as a nickellic hydroxide solid. Cobalt can be recovered from the leach solution by precipitation of a cobaltous/cobaltic cyanide double salt. The double salt product can then be subsequently treated to produce an appropriate cobalt product. The process chemistry, proposed fiowsheet and preliminary reagent costs are presented and discussed.

Jan 1, 1998

By R. Boom, Y. V. Meteleva-Fischer, B. Kraaijveld, H. Kuntzel

"Segregation of impurities during refining of metallurgical grade silicon (MG-Si) is an option to produce solar grade silicon (SG-Si). Directional solidification is a last step in production of SG-Si effective for removal of metallic impurities. The possibility is investigated to use metallic impurities originally present in MG-Si for removing boron and phosphorus. MG-Si has been treated using two methods: 1) alloying with calcium and 2) refining with Na2O-CaO-SiO2 slag, both by controlled cooling. The microstructure of silicon and the impurities distribution have been studied before and after the treatments. Using EPMA phosphorus and boron have been detected in 1-2 wt% concentration range in several intermetallic compounds in grain boundaries after both treatments. This observation points to a different possible mechanism of silicon refining from boron and phosphorus. Controlled cooling improves migration of phosphorus and boron to the silicide phases in grain boundaries, which can be removed by acid leaching treatment.2. IntroductionStandards for silicon solar cells and growing demand on “green” energy require economical and efficient route to the production of solar grade silicon. Refining of cheap metallurgical grade silicon is one of the promising options, where application of existing metallurgical approaches can result in cost-efficient production on industrial scale. Focus in refining is on impurities, which are most difficult to remove: B, P, Al, Ti, due to their large segregation coefficient in silicon and low vapour pressure [1]. Moreover, more environmentally friendly technology in comparison to the traditional Siemens process [2] will be in accordance with societal needs. Based on properties of common impurities in metallurgical grade silicon, alloying refining and slag refining are suggested as competitive techniques having potential effect on removal of impurities harmful for conversion of solar energy [3, 4]. Alloying with Ca followed by acid leaching was found to be effective for removal of Fe and Ti from silicon [5] and to enhance also removal of boron [6] and phosphorus [7, 8]. In the work of Inoue et al. [8] drastically increasing removal of phosphorus from silicon has been observed with an increase of Ca content and a thermodynamics-based explanation was provided. Since phosphorus has been found to condense in the secondary precipitate mainly composed of CaSi2, it can be removed together with iron and titanium by consecutive acid leaching treatment. Slag refining is one of the metallurgical methods proposed to be effective for refining of metallurgical grade silicon from boron [9, 10]. Slags with additions of the following oxides to silica have shown positive effect on removal of boron: CaO [11-13], Na2O [11,14]. Mechanism of slag refining from boron is based on oxidation of boron followed by its incorporation in the slag network [9,11]; the same mechanism is suggested for refining from phosphorus taking into account that oxides of boron and phosphorus are known as network-formers [15]."

Jan 1, 2012

By D J. Brake

The underground metalliferous mining industry continues to change under the influence of many factors including, to name a few, new mining techniques and equipment, new approaches to risk management, more stringent safety and health standards, new employment practices and orebodies become deeper and often lower grade. In addition, the same technological revolution and plummeting cost of technology that has brought the GPS, smart phones and digital cameras to the general population is also working its way through the mining industry impacting on communications, automation and process control as well as introducing major efficiency and productivity dividends. However, not all factors are positive including, in particular, the issues of carbon costs and electrical power. This paper explores some of the trends affecting ventilation in hard rock mines, some of the existing and likely future challenges and some of the potential future solutions to these issues.CITATION:Brake, D J, 2013. Ventilation challenges facing the metalliferous sector, in Proceedings The Australian Mine Ventilation Conference , pp 3-12 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

By Essie Esterhuizen, Michael M. Murphy, Chris Mark

"The design of underground coal mines requires a clear understanding of the overburden response, the loading of pillars, the loading of the gob, the pillar failure process, and the ultimate load carried by partly or fully yielding pillars. Very few highquality stress measurements of yielding pillars and gob loading have been made in full extraction mining. Well-calibrated numerical models can assist in providing a better understanding of the load and failure processes, provided the coal, the overburden, and the gob are all modeled with sufficient realism. A program of numerical model calibration and validation was carried out using FLAC3D.1 The models were calibrated against observed and measured performance of coal pillars and the overburden in operating mines to provide a basic set of input parameters that can be used to provide a realistic first estimate of expected ground response and pillar loading. Input parameters for modeling coal pillar response were based on data from triaxial testing on coal samples, combined with both matching the depth of failure in the coal ribs to observations as well as matching the peak pillar resistance to an empirical equation. The models were calibrated against strong roof and floor case histories in which the pillar strength is governed by failure and yielding of the coal within the pillar and the surrounding strata only had a limited impact on pillar strength. Input parameters for the overburden were determined from a large database of laboratory tests and model calibration against maximum subsidence and subsidence curvature. Further overburden calibration was carried out by matching stresses in the mining horizon to field measurements. Three examples of the application of the calibrated dataset and modeling methodology to field measurements are presented. The results show that a reasopable estimate of the in-seam stress distribution and overburden response can be obtained for both strong and weak overburden scenarios at various depths of cover.INTRODUCTIONThe planning and design of coal mine excavations requires reliable estimates of the expected strength and loading of the mine structures to achieve global stability. Empirical methods are widely used to estimate the strength and loading of coal pillars and have been incorporated into pillar design procedures, such as Analysis of Longwall Pillar Stability (ALPS) (Mark, 1987) and Analysis of Retreat Mining Pillar Stability (ARMPS) (Mark and Chase, 1997), that are widely used in the United States. ~umerical models are finding increasing application as a tool for underground mine design because of their. versatility and the ever increasing computational power available to mine designers. A prerequisite for the application of numerical models is the calibration of the models against observed rock mass response (Hoek et al., 1990; Skiles and Stricklin, 2009). The calibration process may include comparison of model results to measured stress and deformation and modifying the input parameters in a systematic manner to achieve a satisfactory agreement between the model results and measurements. Once models have been calibrated, they can be applied to evaluating similar mining layouts in similar geological conditions."

Jan 1, 2010

By Willard J. Tesch

The borehole surveying system described is used to measure ground movement over and near operating mines. The magnitude of any movement is con-trolled by the ground conditions, the mining method, and the mine progress. By correlating these factors with the measured movement, equations can be determined for predicting the effect of mine progress on the surrounding ground. These equations can also be used to predict the effect of mining a similar deposit with similar ground conditions. The borehole surveying system is used in cased boreholes to measure the inclination of the hole in two perpendicular planes. Grooved casing with an inside diameter of 3 inches is grouted in the hole. Two probes are used to obtain the data necessary to calculate the hole position versus depth. One of the probes contains a gyroscope, and the other contains a biaxial force-balance [s]ervoaccelerometer. Readings from the transducers in the probe are punched on paper tape by an automatic data acquisition system as the probe is pulled up the hole at 30 feet per minute by an electric winch. Readings from the inclinometer probe containing the accelerometer are used as input data to an on-line programmable calculator as they are punched on tape. The calculator computes preliminary results of the survey being made. The paper tapes obtained during the survey runs are later used as input to a computer that computes the offsets of the drill hole versus depth in true north-south and east-west planes. These offsets are printed for each foot of depth. Changes in these offsets between the first survey and subsequent surveys are a measure of the horizontal ground movement between the surveys.

Jan 1, 1976

By C. Q. Cupps, R. F. Zaffarano, J. Fry

Reservoir oil analyses from seven wells in the Greater Clareton area have been included in a study of the original characteristics of oil in the Newcastle sandstone reservoir . These data correlated with areal location of the wells show an increase of saturation pressure in a general north - south or downdip direction . The increase amounts to about 500 psi in more than 17 miles , which corresponds to a depth increase of about 1,600 feet . To facilitate application of the data to engineering analyses , average characteristics are given for arbitrary north and south divisions of the 22 - mile - long producing area . The downdip increase of saturation pressure is taken as evidence of updip diffusion of solution gas from a somewhat higher concentration at the bottom of the reservoir . This effect is opposite to that previously observed in two prominent high- relief reservoirs in the Rocky Mountain area . The increasingly greater saturation pressures southward or downdip in the Greater Clareton area suggest a continuing migration of fluids into the structure .

Jan 1, 1964

By R. Stefanko

Rock bolting as a method of support continues to increase with applications in many other industries in addition to mining. Nevertheless, with nearly 55,000,000 roof bolts installed in coal mines alone last year, this remains as the single greatest use. While bolts have frequently supported ground where conventional timbering could not, there are relatively few design criteria; and trial-and-error procedures prevail. Furthermore, development of suitable instrumentation that is simple to install and readout, sensitive, durable, reliable, safe and economical in evaluating the effectiveness of a bolt over long periods of time lags behind. Therefore, the pull test continues to be the most popular method of evaluating the applicability of a certain type of roof bolt under specific installation conditions. At Penn State in the Department of Mining, research has been conducted for a number of years to measure bleedoff in carefully controlled laboratory experiments as well as in underground investigations.1,2,3,4 Unfortunately, most of the instrumentation developed has been primarily suitable only for research purposes, not possessing all of the aforementioned characteristics desirable for routine underground use. Other groups also have met with restricted success. Therefore, while relatively crude, the torque wrench continues to remain as the most widely used load measuring device. While both field and laboratory tests continue to be conducted, analytical analyses are attempted to discover the more important design parameters in order that more efficient anchorage might be devised.

Jan 1, 1969

By Monica M. Jimenez Correa, Jorge A. Soares Tenorio, Denise Crocce Romano Espinosa, Paula Aliprandini

The surface zone of nickel laterite ore is generally considered as residue. However, because of the depletion of ore sources and the increase in demand, this previously discarded zone may now be processed economically for nickel and cobalt. After leaching and removal of the impurities, the solution contains cobalt, magnesium, manganese and nickel. Solvent extraction is a hydrometallurgical technique used in the separation of metals from aqueous solutions. Cyanex 272 and D2EHPA are extractants used to separate nickel from cobalt. The mixture of extractants can change the performance during the metals extraction. This work aims to evaluate the solvent extraction of nickel and cobalt when Cyanex 272 and D2EHPA are mixed. The results showed that the increased concentration of D2EHPA in the organic phase increased the extraction of nickel and magnesium. However, cobalt extraction was reduced and the manganese extraction was not altered.

Mar 1, 2018

By Jerry C. Tien, Yingjiazi Cao

"Coal spontaneous combustion (SponCom) is a natural phenomenon in underground operations, which can either happen naturally or be triggered by human activities. For underground operations, espe-cially in coal, SponCom can happen frequently as a result of air leakage, although its incubation period may vary depends on types of coal and surrounding environment, resulting in uncertainty in control. In China, most of the underground coal operations now use longwall mining method because of its superior safety, high productivity and efficiency. With an increased popularity, there is also an increasing necessity to study spontaneous combustion, its occurrence and management. There have been many theoretical analysis and experimental studies over the past half century hoping to understand the occurrence of coal combustion and its control measures to better understand the occurrence and to design controlling measures to limit the dam-age it causes. In this paper, research on coal spontaneous combustion fundamentals from these three aspects will be reviewed, gaps highlighted and possible directions for future studies. INTRODUCTION The history of anthropic development is the history of human's energy utilization progress. From the first usage of fire, people have been continuingly seeking energy resources on earth. Coal, as an abundant, economic and convenient source of fuel quickly became indispensable and made significant contribution to economic growth worldwide. With technology and societal development, people are becoming more and more coal-dependent, but at the same time, problems of fossil fuel combustion came into sight. In global coal mining industry, spontaneous combustion has now presented one of the most challenging safety issues, it is also believed that it has contributed significantly toward the climate change. It is essential that more effort be invested to examine the cause of SponCom and its control measures. Coal SponCom is a complex process, with both physical and chemical inter-actions among various interrelated factors such as local airflow distribution, ventilation pressure, methane emissions (if any), and physical surroundings underground. With the advent of powerful computers, simulation techniques and af-fordable modelling packages in recent years, significant advances have been made in understanding sponta-neous combustion. But because of the complex nature of combustion and varying underground conditions, there are still areas that need further examining. This paper will focus on illustrating the current research of coal spontaneous combustion and addressing research gaps and future study areas."

Jan 1, 2019

By Kenneth M. Earl

This report describes the results of a field study conducted by the Bureau of Mines during 1956 and 1957 on manganese-and iron-bearing mineral deposits in the southern district of Aroostook County, Maine. The work was undertaken to determine the extent of deposits largely concealed under glacial drift and to obtain subsurface samples for manganese mineral identification and research in ore dressing and extractive metallurgy. The investigation was confined to the Westford Hill-Daggett Hill area in Hodgdon Township and to the Stewart prospects and vicinity in Linneus Township. Over 50 magnetic anomalies were mapped by magnetometric surveys in the Westford Hill-Daggett Hill area, Hodgdon Township. The largest anomaly, as outlined by the 1,000-gamma contour, indicates a deposit 3,200 feet long with a maximum width of 350 feet. The smallest anomaly measures about 10 feet wide by 25 feet long.

Jan 1, 1962

By V. A. Chanturiya

In Pt- and Au-keeping complex ores processing, about 10% ~ 15% of noble metals are lost with true tailings that are due to low floatability of Pt- and Au-keeping minerals by the conventional collectors. With the aim to achieve the effective recovery of noble metals at flotation of Pt-Cu-Ni and Au-keeping ores organic complex reagents keeping electron-donating atoms of nitrogen, oxygen, sulfur or phosphorus may be offered as selective collectors for the indicated minerals. These rea-gents tend to form complex compounds with PGM. Besides this, Cu-Ni-Pt and complex Pt and Au carbonated mica ores are characterized by finely disseminated (up to nanometer size) mineral forms of Pt in multivalent states. In this connection, the use of a combination of the strong ionic collectors with nonionic reactants that are capable to derivate complex compounds with multivalent PGM seems to be expedient for this type of ores. In the research new complex reactants were tested such as cyclic alkylene-trithiocarbonates, oxyalkyl butylxanthogen acid ethers, a combination of the collectors ? mercaptobenzothiazole (MBT) and dialkyldithiophosphates (DTP). Sorption and flotation tests were made with monomine-ralic samples of chalcopyrite, pentlandite, pyrrhotite, pyrite, and Pt-Cu-Ni sulfide ore samples. Sorption properties were examined by the extractive UV spectrophotometric method and potentiometric measurements. To indicate a structure of modified xanthate solutions the method of a thin-layer chromatography (TLC) was applied. The chromatographic behavior of the basic components of modified xanthate solution ? ButX, cyclic propylene-trithiocarbonate (PTTC), diethyl-dithiocarbamate (DEDC) and the product of its modification ? oxypropyl-S-ether of dithiocarbamatic acid was studied on plates ?Silufol UV ? 254?. The composition of organic solvents and its ratio in a mobile phase was deter-mined for simultaneous chromatography of the main components of a reaction mixture. It was found that operating selectivity of MBT, DTP and cyclic alkylene-trithiocarbonates incorporated in modified xanthate in relation to Pt-Cu-Ni and Au-containing sulfide minerals might be explained by an electoral sorption of this nonionic collector on a surface of the minerals studied. It was demonstrated that the application new reagent modes with the use of a combination of designed complex reactants helped to increase the extraction index of Pt- and Au-keeping minerals from complicated ores.

Jan 1, 2014

By Galen G. Waddell

Several years of rock-burst research conducted by the Federal Bureau of Mines, in cooperation with the mining companies of the Coeur d?Alene Mining District, Idaho, in addition to progress made by others throughout the world, have led to a good understanding of the rock-burst problem. This paper describes conditions which have caused specific bursts, present capabilities of detecting stress buildup and bursts, control methods, and a suggested approach to analyzing any individual mine-burst problem.

Jan 1, 1970