Search Documents

By Ting Ren, Jon Roberts, Zhongbei Li, Ming Qiao, Jianming Wu

Spontaneous heating of coal continues to present a health and safety hazard in underground coal mines. The influence of seam gas composition on gas flow dynamics and distribution characteristics in the active longwall goaf has not been studied in-depth, and corresponding effective proactive goaf inertization strategies for preventing potential spontaneous heating from occurring have limited investigation. To advance this knowledge, an 80-m-height goaf model was constructed and developed based on specific conditions of an Australian underground coal mine, and onsite gas monitoring data was collated to verify base model results, which allowed for various scenarios of seam gas composition to be simulated and investigated with confidence. This study involved modeling five different gas composition scenarios for the goaf atmosphere, namely, 100% CO2 (case 1), 80% CO2 and 20% CH4 (case 2), 50% CO2 and 50% CH4 (case 3), 20% CO2 and 80% CH4 (case 4), and 100% CH4 (case 5). Simulation results show that O2 is primarily distributed at the middle and upper part of the CO2- dominant goaf model, while it is mainly layered at the floor level of the CH4- dominant goaf model. N2 is superior to CO2 in the goaf inertization for the CO2- dominant goaf model, whereas CO2 performs better than N2 for the CH4- dominant goaf model. The optimal inert gas flowrates for case 1 to case 5 are 1.5, 1.75, 0.75, 0.5, and 1.0 m3/ s, and the oxidation zone area is reduced by 55.76%, 67.21%, 58.04%, 78.17%, and 81.82%, respectively. The simulation results allow for increased insight and understanding of the gas distribution patterns in the active goaf with different seam gas composition and the development of corresponding proactive goaf inertization practices, thus minimizing potential spontaneous-heating-related hazards and improving mining safety.

Sep 26, 2023

By Richard V. Ageton, Harry E. Tufft, E. A. Holbrook

When an underground excavation is made, the rock surrounding the sides and top of the opening is deprived of its natural support and tends to fall. Whenever caving takes place, the time and extent of the caving depend on the character and condition of the rock. In strong homogenous rock, such as solid granite, even a large chamber may stand indefinitely, whereas a soft material, such as clay or a loose material like unconsolidated sand, falls immediately if not supported. Weaknesses in the rocks induced by structural features, such as joints, :fissures, bedding and cleavage planes, and fractures produced by blasting, will cause the falling of insecure blocks or slabs unless means are provided to support these in place. In an unsupported mine opening, as a tunnel, the first slight settling or adjusting movement of the rocks (the "initial creep" or "set") is caused by the great weight of overlying material pressing down the rock masses above and around the roof and sides of the opening until they key together in roughly the form of an arch. The rock, after it has adjusted itself to this shape, becomes. selfsupporting. Timbering is necessa.ry in all mining only to support, therefore, those comparatively small blocks or pieces of rock which tend to loosen from the top and sides of the opening during or after the formation 'of the natural rock arch, and which lie between this natural rock arch and the opening. This statement, of course, has its limitations. For example; a layer of strong rock, like limestone, may act as a beam; then only the material under the limestone will need support. Timbering is not, as is commonly supposed by the layman, used to supp!ort the huge mass of rock between the back (roof) of an underground opening and the surface. It would be impossible to place enough timbers in a:ny underground opening to support such a mass. This fact is not'·perceived by all miners.

Jan 1, 1923

By W. Hodge Caraway

This report presents the results of an evaluation of several indirect methods of measuring the water content of oil-reservoir rocks. The water content of oil-base cores is considered to be most nearly representative of the water content of the undisturbed petroleum reservoir and therefore, the direct method of measuring the volumes of water in cores cut in oil-base drilling fluid was adopted as a standard for comparison. The indirect methods evaluated included (1) displacement through a semipermeable membrane by air, (2) centrifuge, (3) evaporation, (4) mercury injection, (5) chloride dilution and (6) electric logs. Approximately 270 samples of cores from petroleum-reservoir rocks were used in the study. The cores, most of which were cut with oil-base mud in the hole, were taken from oilfields in California, Texas Gulf coast, Colorado, Oklahoma, and Alaska.

Jan 1, 1959

By W. B. Boggs

The Noranda smelter was built by Noranda Mines, Limited, from the designs of A. E. Wheeler, consulting metallurgist, New York, for the reduction of ores and concentrates from the Horne mine, and to treat, on a custom basis, ores and concentrates from other mines in the Rouyn district. The smelter is situated at Noranda in western Quebec, about 330 miles directly north of Toronto. Ground was first broken for construction in November, 1925, before the completion of the branch railway into the district, which was not finished until October, 1926. After many difficulties and delays due to the Jack 'of transportation and the severe weather during the winter months, the smelter was started in December, 1927, and the first blister copper was poured on December 17th. The smelter was built throughout in two duplicate units, each with a rated capacity of 500 tons of ore per day. Operations were started with only one unit, and after several months it was found that one unit alone would smelt 1,000 tons of ore per day. At this time only one shaft, No. 3, existed, and its hoisting capacity and the capacity of the original crushing plant were insufficient to supply ore for two units at the increased tonnage. Accordingly No. 4 shaft was sunk and a new crushing plant provided to handle the ore hoisted there. This work was completed in the latter part of November, 1929, and since that time both smelter units have been operating.

Jan 1, 1930

By J. Sepulveda

"Despite the recognized influence of product fineness on line capacity and downstream process performance, few mineral concentrators today use particle size measurement of the final product in automatic control applications for particle size. ‘Near-line’ particle size instrumentation has existed for decades and is utilized in modern concentrators, but low availability and measurement frequency, due to problems with slurry sampling and transport systems, make these technologies unreliable for use in automatic control. An innovative technology for real-time particle size measurement on individual hydrocyclones, named CYCLONEtrac™ PST (particle size tracking), has been developed by CiDRA Minerals Processing, and proven in commercial installations, demonstrating near 100% availability with minimal maintenance requirements, thus overcoming the limitations of previous technologies. Potential stakeholders require convincing, reliable information regarding the economic value delivered by automatic grind control projects. In this paper we present a methodology for estimating such value with the CYCLONEtrac™ PST technology, and demonstrate unique opportunities to improve process stability and performance. Based on actual plant data accumulated over time, the evaluation approach assesses and highlights the significant potential process improvement that can be expected with the particle size tracking technology. As an extension of previous work, in this paper we present the key operating criteria for optimizing the production of valuable metals and increase mill throughput by identifying the optimal grind size. As this requires operating closer to the process boundaries, accurate real-time particle size measurements, such as those provided by the CYCLONEtrac™ PST system, become essential for achieving the maximum potential value from every operation. For further illustration, data from three different copper plants is compared.Introduction Owners and operators of mineral concentrators constantly search for the most economically attractive way to increase the output of valuable metal. A logical approach is to identify a key parameter that has the greatest impact on the performance of multiple stages of the process and then use a holistic analysis methodology to determine how this key parameter can be controlled to optimize the final output.Particle size is widely recognized as such a key parameter; however, very few concentrators today use real-time particle size measurements for automatic control of the final product size due, to a large extent, to the inherent limitations of existing technologies. ‘Near-line’ particle size measurement instrumentation, which has been used for decades, typically suffers from low availability because the fundamental measurement technologies were developed for other, less demanding industries and then adapted to the harsh environment of the typical mineral concentration process. An outline of the key differences among the available technologies used for particle size measurement in comminution circuits has been completed in previous work, and plant data has proven the benefits of measurements on individual cyclones – something that, until now, has not been possible (Cirulis, 2017)."

Nov 1, 2018

By Lotfollah Nahai

India is one of the fortunate countries that has substantial reserves of many raw materials for producing steel; however, for historical and economic reasons these resources have not been aggressively developed until recently. Production of steel on an industrial scale started in 1912, but annual output was below 1 million tons3 in 1938 and about 1,500,000 tons in 1951. Expansion of the steel industry became one of the objectives of India's economic planning after independence in 1947. The Planning Com¬mission's 1951 report emphasized the importance of steel production, but financial obstacles, emphasis on river valley projects, and priority for increased food production in the First 5-Year Plan (1951-56) did not permit large-scale expansion of steel capacity. The 1956 planned target for crude steel, only 1,650,000 tons, was actually exceeded by production of 1,737,900 tons. In the Second 5-Year Plan (1956-61), however, construction of steel plants received a high priority. Currently three new steel plants, each with an annual capacity of approximately 1 million tons of steel, are nearing completion in Rourkela, Dorgapur, and Bhilai. Simultaneously, the two privately owned steel plants and the small State-owned plant in Mysore have been enlarged and modernized. As a result, India's crude steel capacity will be about 6 million tons in 1961, almost evenly divided between Government-owned and privately owned plants. Actual production in 1960 totaled 3,254,000 tons compared with 2,434,000 tons in 1959. Assuming that the population will be 430 million and that capacity production will be achieved, the 1961 per capita steel output will be only 31 pounds compared with 200 pounds for Japan in 1959. Some Indian experts feel that development of steel-consuming industries merits greater emphasis in the Third 5-Year Plan (1961-66) than expanding existing steel-producing facilities. Nonetheless, the Third 5-Year Plan calls for a 10 million ton annual capacity by 1966 to be achieved by expanding the Government-owned plants in Bhilai, Durgapur, and Mysore, and by establishing a new integrated Government plant in Bokaro, in the State of Bihar.

Jan 1, 1961

By M. Vallée, J. -P. Charette, D. P. Gold

"The Oka Carbonatite and Alkaline Complex is a Lower Cretaceous intrusive body of the Monteregian petrographic province. Carbonate rocks of various types, and associated alkaline rocks of the ijolite and okaite suites, are distributed in a double ring-dyke structure 4 Yi miles long by 1 1/2 miles across. Alnoite and alrioite breccia pipes intrude all rocks of the Complex and indicate, from inclusions, that a cover of Palaeozoic rocks existed at the time of emplacement.The results of radiometric, magnetic and gravity surveys of the Complex are compiled and discussed both with respect to the regional pattern and, locally, the bed-rock geology. The Complex is characterized by high-intensity anomalies.Exploration activities started during 1953, and mining operations began in 1961 on the property of St. Lawrence Columbium and Metals Corporation, at one time the world's largest producer of niobium concentrates. Because of the boudinaged and fractured nature of many of the rocks and the variability in grade of the ore minerals, the role of the mining geologist is both demanding and exacting. Rock types are varied and their mutual relation-ships ambiguous, the minerals are rare and complex, and close geological control of the ore is needed in the mine and in the mill. Closely spaced diamond drill holes are needed for mining control, and the ore-waste contact is defined mainly by assay results.In the exploration for 'carbonatites' in Eastern Canada, aeromagnetic surveys are judged to be the best exploration tool, followed in decreasing order by the search for circular structures on aerial photographs, regional gravity surveys and radiometric surveys."

Jan 1, 1967

By Michel Jébrak, Claude Bellehumeur

Abstract - Regional and orientation geochemical stream sediment surveys were carried out by the Quebec Department of Energy and Resources in southwestern Quebec, over a part of the Mont­ Laurier Terrane of the Grenville Province. The area contains some small stratiform zinc deposits. The response of Zn mineralization to geochemical surveys is weak; the known mineralization is not defined by anomalous samples and consistent patterns. This study uses a technique that increases the geochemical signature of Zn mineralization in filtering out geochemical background components related to lithologies and surficial conditions. The background variations were modelled using principal component analysis, and the filtering technique consists of the partial reconstruction of the data matrix from results of principal component analysis . The filtering procedure considerably enhances the Zn anomalies located in the catchment basins of Zn deposits, and defines some new anomalies in proximity to the marbles of the Mont-Laurier Terrane, the principal metallotect of Zn mineralization.

Jan 1, 1993

By Fred Hodges

This paper describing the concentrator practice of the Hurley Plant of the Nevada Consolidated Copper Co. at Hurley, N. Mex., is one of a series of papers on milling methods and costs being prepared by the United States Bureau of Mines. The Hurley concentrator has a normal daily capacity of 13,500 tons of ore, and for the first four months of 1930 the heads of the concentrator averaged 1.32 per cent of copper and 3.14 per cent of iron. The recovery for this period was 83.98 per cent and the concentrates produced averaged 27.54 per cent of copper.

Jan 1, 1931

By Oliver C. Ralston

DURING the development of froth flotation for the treatment of sulphide ores, a certain amount of information was collected about a few of the nonmetallic minerals, and occasionally the gangue minerals in the sulphide ores showed an embarrassing tendency to float. However, for many years efforts were expended to develop reagents that would cause wetting and depression of these minerals. Among the nonmetallics, the minerals sulphur, graphite, and talc probably should be classified as 'natural floaters', and perhaps sericite. They respond to almost any type of flotation reagent, and their beneficiation by flotation had been attempted years ago. Flotation of sulphur is now common practice, and graphite was concentrated during the World War in many mills, most of which have now closed down. A talc mill has just been constructed, and another may soon be erected. Second to the 'natural floaters' come the 'easy floaters', cassiterite, fluorite, barite, mica, colloidal gangue, and paper pulp from white water of paper mills. That these materials responded to some of the early flotation reagents, as oleic acid, has long been known; occasional references to their behaviour are found in the very early flotation literature and in that of today. In general, however, nonmetallic minerals, valued at $2.00 to $15.00 per ton, have for a long time been regarded as cheap products and not worth much beneficiation. Consequently, only high-grade natural deposits suitable for direct mining and sale have been gouged out. Furthermore, the mining of these minerals has too frequently been in the hands of 'super-practical' men-men of no technical or other training, willing to work for a very low compensation. From the social standpoint, nonmetallics has been the field for small, untrained enterprisers with little money to spend on plant or equipment. But times have been changing. The impact of technically trained men on the old industry has revealed appalling losses and inefficien-cies and proved the value of processing materials discarded or avoided by the old regime.

Jan 1, 1937

By R. W. Michelson

The Bureau of Mines developed computerized mathematical models to estimate the economic availability of Mesabi Range taconite concentrates; these are a quality model, a cost model, and an economic availability model. The quality model evaluates metallurgical test data; the cost model determines iron unit cost from mining and processing cost data; and the economic availability model determines quantity from geologic and ore quality data. By correlating all of the physical resource quality factors and dimensional characteristics with the economic cost factors associated with producing iron ore pellets, these three models combine to establish a final relation between iron ore reserve quantities and iron unit cost.

Jan 1, 1970

By James F. Devine

The radial, vertical, and transverse components of particle velocity were recorded by Bureau of Mines investigators along gage arrays extending in one or two directions for 145 to 3,170 feet at five quarries. Of the 39 quarry blasts, 12 were instantaneous blasts, 5 were of the one hole per delay type, using millisecond delayed caps, and 22 were multiple hole per delay type employing millisecond delay detonating fuse connectors. Charge weight per hole ranged from 8 to 1,500 pounds, and the charge weight per delay interval, including the instantaneous blasts, ranged from 25 to 4,620 pounds.

Jan 1, 1966

By Reis. E., P. Pino Véliz

"Along the process of defining the fundamentals of a ferronickel project, several questions require proper answers from the very beginning such as the size and characteristics of the laterite deposit (oxide or silicate), the mineralogical variability, and the selection of the most valuable process route. In general, these elements will be defined along the progress of the exploration and feasibility studies, and definitive engineering. Also, from the very preliminary estimates, three questions are very common: what should be the plant capacity (annual tonnes of contained nickel), what will be the probable capital required (CAPEX), and what will be the estimated timeline (schedule) between the initial stage, say the feasibility study and the plant start-up and ramp-up to designed capacity. The accuracy of the capital cost estimates also progresses along the different stages of development from ±50% at the Preliminary Economic Assessment (PEA) stage down to ±5% for the Detailed Engineering and Construction stage. These accuracies of estimates have been, in some ways, accepted by the mining community and investors. The industry accepted benchmark for ferronickel projects in terms of CAPEX are then in the order of US$50,000 per tonne of nickel contained in the FeNi product. In this paper, the authors analyze in some details three ferronickel projects for lateritic ores that have selected the Rotary Kiln - Electric Furnace (RKEF) as the suitable technological route and have started production in the period 2006–2016. Some key aspects of the ferronickel projects are examined: 1) size and type of deposit; 2) flowsheet selection; 3) evolution of capital cost as a function of capacity from the feasibility stage to construction; 4) comparison between planned production scale and actual ramp up; 5) estimated capital expenditure (CAPEX) compared with actual figures; 6) nickel price evolution and timing of the approval for the project to proceed to construction and production start-up. The objective of this paper is to identify key elements that should be addressed in future projects and that are proposed as benchmark figures for similar projects."

Jan 1, 2017

By Gerhard Braüner

The present knowledge on ground movements and mining damage is mainly based on observations made when mining seamlike deposits. The studies, rules, and regulations in different countries agree in that the differential ground movements, especially the strain, account for the damage to structures. Accordingly, large buildings are particularly susceptible. The opinions on what amount of ground deformation induces what degree of structural damage are not quite uniform. Mining damage can be reduced or prevented by structural and/or underground precautions. The latter comprise measures for generally reducing the ground movements (leaving pillars, filling, partial extraction) and for reducing temporary movements (rapid extraction, specially arranged workings). Because the differential movements decrease with increasing depth of mining, safety pillars are largely dispensable at greater depths. Shafts are mainly affected by the vertical derivatives of rock displacements, but extraction in the vicinity of shafts is feasible even under difficult conditions. The theoretical concept of the ground movement process established in part 1 of this work is in qualitative agreement with the facts herein observed. As a quantitative approach, it should be applied to calculating ground surface movements rather than rock movements about underground openings. It can be extended by introducing more detailed strata characteristics.

Jan 1, 1973

By S. M. Bulatovic

The western industrial world has to rely more and more on complex polymetallic sulphide ores as sources for base metals. These ores are composed of fine grained sulphide minerals such as chalcopyrite, galena, sphalerite, pyrite, pyrrhotite and marcasite. The liberation sizes of the individual minerals can range between 30 um and 5 um. Therefore, applying conventional techniques to recover these finely disseminated minerals usually results in unsatisfactory metallurgical performances with high losses of the valuable mineral to the slime , fraction of the tailing. New concepts for treating these polymetallic complex ores are discussed in this paper. Beneficiation techniques utilizing new reagents and a new approach to pulp preparation are described. Some of these techniques were applied to ores from existing concentrators as well as to new ores. The results of these studies are discussed in the following sections.

Jan 1, 1990

By J. Hoover Mackin

The iron ore bodies of the Iron Springs district are replacement deposits of magnetite and hematite in Jurassic limestone around the borders of three intrusions of quartz-monzonite porphyry. Production in the period 1923-1965 was about 72,000,000 tons, nearly all of which was direct-shipping ore from open pits. The intrusions are laccolithic in form; all three were emplaced at the same stratigraphic horizon, which had been a zone of decollement gliding during the Laramide orogeny. The intrusions and associated volcanic rocks are post-orogenic. There was no change in the thickness of the limestone during the metallization. Comparison of the composition of the limestone and stratigraphically equivalent replacement ore indicates that, with every million tons of iron, there were additions of 40,000 tons of silicon, 20,000 tons of magnesium, and 10,000 tons of aluminum. The ore-forming fluid was derived from the exposed porphyry. The iron was first incorporated in hydroxyl-bearing mafics, which crystallized in depth and were carried upward in the magma that formed the hypabyssal intrusions. The mafic phenocrysts decayed deuterically in the new environment, releasing iron into the interstitial fluid of a consolidating crystal mush in the interior of the intrusions. Primary tension joints, which opened in areas of late intrusive distention, served as roots through which the ore-forming fluid was drawn from the crystal mush.

Jan 1, 1968

By O. C. Blade

A summary of the characteristics of motor gasoline for the summer 1951 is presented in table 1, and for comparison, a similar summary for the summer 1950 is shown in table 2. Trends of some of the more important characteristics over a period of years are shown in figures 1 and 2. As indicated, octane numbers of motor gasolines sold in the United states decreased approximately one-half to one octane unit from the record levels attained during the winter of 1950-51 and are a little below the octane numbers of summer 1950. However, average vapor pressures of the summer gasolines did not change, and certain distillation temperatures varied only slightly from those of the year before.

Jan 1, 1952

By S. H. Ash

The coal-mining districts of Washington are mainly situated west of the Cascade Mountains. The eastern boundaries of Whatcom, Skagit, Snohomish, King, Pierce, and Lewis Counties, shown in Figure 1, form the backbone of the mountain range. The mines are on the foothills of the slope and extend to the shores of Puget Sound in the central and northern portions. The subbituminous fields of Lewis, Thurston, and Cowlitz Counties extend into the valleys west of the mountains. The Roslyn field, a small but important area, Lies on the eastern slope of the Cascade Range. If western Washington is divided into three areas from north to south the bituminous coal fields and most of the active mining operations will be found largely in the central area. In the southern portion there are large areas of subbituminous coals of varying quality extending from Centralia to the Columbia River. In the northern portion, mining is at present practically restricted to one mine which is working a subbituminous bed near the city of Bellingham.

Jan 1, 1931

By Charles L. Kimbell

The final 26 tables of this chapter, tables 25-50, extend and expand the statistical series on production that was started in the 1963 edition of the "Area Reports: International" volume of the "Minerals Yearbook" and that was subsequently updated and expanded in the 1965 and 1967-89 editions. Continuing the practice started in 1989, a column has been included in each of these tables providing a 5-year average for 1986-90, inclusive. This should provide a clearer picture more rapidly of the role of each major producer over the 5-year period. The listing order of major producers, however, continued to be, as in past years, in descending order of rank in the year of review, 1990. With the inclusion of silver and uranium in the 1988 edition of this chapter, this group of tables now includes each of the crude minerals that ranked from 1st to 19th in 1983 terms of value of their output (as well as four others of lesser rank). These 23 crude mineral commodities accounted for 93% of the estimated value of world crude mineral production in 1983. In addition, world output of five key downstream products-aluminum, steel, cement, nitrogen in ammonia, and refined oil-are included because of their significance as products.

Jan 1, 1993

By J. R. Klaehn, M. Shi, T. E. Lister, L. A. Diaz, J. S. McNally

Since 2019, approximately two dozen international battery recycling companies have been operating at the commercial or pilot scale [1]. However, current process capacity does not exceed 100,000 tons of end-of-life (EOL) lithium-ion batteries (LIB) per year, and the current recycling rate is only about 5% in North America [2-3]. Recycling metals from EOL LIBs is not only essential to waste minimization and environmental stewardship, but also a source of critical materials, which can contribute towards supply chain stabilization. LIB recycling can be roughly divided into three categories: direct recycling, pyrometallurgy, and hydrometallurgy. Direct recycling seeks to retain as much of the manufactured effort with minimum chemical processing [4]. The evolution of battery designs and chemical compositions are challenges to this approach [5-6]. Pyrometallurgical processes are robust and flexible allowing a broad spectrum of batteries with minimum pre-processing requirements. Some of the matrix issues are solved through combustion of some constituents. Smelting is strongly tied to fossil energy and air emissions are a concern. In addition, pyrometallurgical processes are not stand alone, as hydrometallurgical refining normally required to separate and recover the metals of interest (Co, Ni, and Cu) from the produced alloy and Li from the slag [7]. Hydrometallurgical processes can be highly selective and efficient in recovering high purity materials [8]. In general, hydrometallurgical processes are considered cleaner and less costly than high temperature processes [4,9-10]. Extensive chemical consumption and waste generation significantly increase the operating costs and overall environmental impact of the hydrometallurgical processes [11]. Leaching of metals from LIBs is dominated by the mixture of sulfuric acid (1 to 4 M H2SO4) and hydrogen peroxide (1 to 15 wt.% H2O2) [10]. Although organic acids have been tested as lower environmental impact alternatives, the reported pulp density operations are low < 60 g/L [10-11]. For the H2SO4/H2O2 leachates, high leaching efficiencies >90% are reported for Co, Ni, Mn, and Li from cathode materials at temperatures over 40 ⁰C and pulp densities between 30 to 200 g/L [9-10]. H2O2 acts as reducing agent to convert Co+3 and Mn+4 into their soluble forms, Co+2 and Mn+2 [12]. Despite the claims of H2O2 being a clean reducing agent [13], production of H2O2 has significant environmental impacts as determined by life-cycle analyses [13-14]. Moreover, the costs and risks associated with H2O2 transportation and storage cannot be ignored [15].

Mar 2, 2022