Search Documents

Jan 1, 1883

'T. C. MERRIMAN, New Haven, Conn. (written discussion *).-This most interesting paper gives much carefully obtained and valuable data. However, there are two points in connection with the commercial application of such data that might possibly be a source of trouble and mis-understanding. In the first place, the examination of thin sections of annealed brass, subjected to standard Brinell test.(500 kg. on a 10-mm. diameter ball) at thicknesses from 0.075 to 0.150 in. (1.9 to 3.8 mm.) indicates that cold work has been performed on the specimen during the application of the load sufficient to extend way through the section, and have the hardness of the metal affected by the backing. If the usual steel support is used, this effect is very evident. If a piece of soft brass is used as a support, there is an indentation in the surface of the support accompanied by a bulge on the under side of the tested specimen opposite the impression made by the 10-mm. ball. The result is that Brinell specifications (governmental or otherwise) on stock for a certain purpose may not be fair in all cases, since manufacturers, owing to differences in equipment, etc., may not all use precisely the thickness and conditions of stock on which the Brinell specifications were based. This would mean that the government Brinell specification might not give them the temper of stock best suited for their manufacturing methods. The concluding paragraph of this paper, stating that "the hardness of cartridge brass may be determined with greater accuracy by the Brinell hardness measurement than by attempting to judge it from the grain size" appears to be in line with the movement of the last year or so among brass manufacturers toward substitution of the Brinell test for microscopic examination as an acceptance test on cartridge brass. The statement may he strictly true that the Brinell test is the best test for hardness, but it is not, as the statement might readily be construed, a sufficient test of suitable condition. For instance, some cartridge brass might accidentally have been overheated to a point where it would be distinctly unsafe to use for the manufacture of small arms cases and then be so rolled (reduction 3 to 5 per cent.) as to pass perfectly proper Brinell specifications. Under such conditions the microscope would reveal its unsuitability where the Brinell test had failed so to do.

Jan 4, 1919

By Joseph J. Wallace, William H. Tavenner, D. A. Reynolds, John M. Provost, James J. Dowd, R. F. Abemethy

"CONCLUSIONSThe investigation shows that there are 5 coal beds of major importance in Wyoming County from the standpoint of present production - Pocahontas No. 3, No. 2 Gas, Sewell, Beckley, and Eagle - and 5 beds of minor importance - Pocahontas No. 6, Cedar Grove, Winifrede, Douglas, and Chilton. The Pocahontas No. 3 bed contains the largest remaining known reserves.Known measured and indicated reserves in all beds, based on a minimum thick¬ness of 14 inches and on 1,800 tons per acre-foot of coal in place, are estimated at 2,665 million short tons as of January 1, 1951. Of this total, 2,121 million short tons is in beds 28 inches and more thick. Areas in each bed were omitted from the estimate because available data relative to the bed characteristics are too meager to make an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.Recoverable reserves of coal have been estimated in beds 28 inches and more thick. This thickness is about the minimum now being mined by hand loading onto conveyors in the Appalachian region. The weighted average recovery for all beds in Wyoming County, as determined by this investigation, is 55.0 percent. This percent¬age is based on the total thickness of coal (less partings 3/8 inch or more thick) in the bed rather than on the thickness of the coal mined. The known recoverable reserves are estimated to be 1,167 million tons as of January 1, 1951.4. Since most of the Wyoming coals are medium- and low-volatile bituminous in rank and expand during carbonization in modern ovens, they are blended with high-volatile contracting coals."

Apr 1, 1953

By A Deakin

It has been almost a decade since the release of the International Council of Mining and Metals (ICMM) Health and Safety Critical Control Management: Good Practice Guide (2015a). During this time the ICMM member companies, along with many others across industry, have been busy designing, deploying and enhancing their own critical control management (CCM) programs. So, what have we learnt? This paper discusses the scope, application and learnings from the implementation of CCM within the mining industry. What’s going well? What are the common challenges? What are the opportunities to strengthen the approach? What are the threats to successful implementation? The paper draws on the author’s experience as one of the key contributors to the development of the CCM Good Practice Guide and an adviser to many mining companies, including six of the ICMM members. The paper focuses on the practical (operational) application of CCM and the cycle of identifying, defining, implementing, verifying and improving critical controls at the frontline. The paper also includes a discussion on the safety performance of the ICMM member companies over the past decade and provides a recommendation for how CCM can be incorporated into a more proactive model to measure safety performance. The paper concludes with practical recommendations that mining companies, regardless of their CCM maturity, can consider as they look ahead. They are supplemented by three additional recommendations for consideration at the industry level.

Apr 16, 2024

By Rudolf E. Greuer

Every mine contains inflammable materials, either in form of the minerals mined or in the form of brought-in supplies. Although great efforts are made to make mines as far as possible fireproof and to prevent ignition sources, the possibility of mine fires, like that of other accidents, will always continue to exist. Detailed statistics are available for coal mines. They show (65,112) that the number of major mine fires in the USA over the last 20 years has remained more or less constant with approximately 50 per year. The same number is reported (26) for the British coal mines. Other countries (147) report about 1 major fire for every 10 million tons of coal production. Conflicting data are published on the number of fatalities caused by fires, presumably because frequently deviating opinions on the cause of death exist. On the average (82,99) 4 miners are killed per year in the US and in the British coal mines. Although this number is much smaller than that for several other causes of fatalities, one must keep in mind that almost every small fire can develop into a large disaster.

Jan 1, 1973

The Cutoff grade optimization is very critical to the open pit production scheduling. In case of single mineral deposits, algorithms have been developed for determining cutoff grade policy that maximizes the net present value (NPV) of yearly cash flows. For deter-mining the cutoff grade policy for projects with two minerals including stockpiles the problem becomes much more complex. The purpose of this paper is to present fundamentals of a generalized cutoff grade optimization algorithm that will maximize the NPV of a project subject to mining, milling, and marketing constraints. Benefits of the methodology developed are demonstrated on three different case studies.

Jan 1, 1997

By Worthen Bradley

A BETTER understanding of what is happening in the domestic quicksilver industry, and what is likely to happen, can be had after reviewing some of the highlights of the past four years. Hitting the high spots in chronological order, they are: February 1939-Army and Navy Munitions Board starts investigation on civilian and war needs of certain "strategic materials," including quicksilver, with a view to recommending stock piles. Every known producer is canvassed by the end of the year.

Jan 1, 1942

By John J. McClelland

The U.S. Bureau of Mines formed a team in 1991 to begin developing a long-range research plan for computer-assisted mining that would benefit the metal-nonmetal mining industry. This report details the team's accomplishments, specifically, the development of a model that identifies metal-nonmetal mining research needs that could be addressed by the application of automation technology. The report also provides a summary of automation needs and applications based on visits with mining company representatives. The status and future direction of this work is also presented.

Jan 1, 1994

By R. L. Summers

The tremendous engineering advances occurring during this past century are very evident within the boundaries of the Anthracite Section of AIME. The Steelton plant of Bethlehem Steel Corporation, located along the Susquehanna River just east of the Commonwealth's capital at Harrisburg, for more than 105 years has experienced a most dynamic life which has paralleled America's industrial growth. (Figure 1) In June 1865, just after the Civil War, a group of men met to organize the Pennsylvania Steel Company. The war had brought into sharp focus the vital importance of the railroads to the country's expansion. Until that time wrought iron rails were used, and the replacing of track after only several months wear had become an almost unbearable cost. The spirit of free, competitive enterprise and the prospects of a lucrative market compelled these men to form that first Pennsylvania Steel Company and to develop better rail products. They issued the following statement: "...our desire to free ourselves from dependence upon a foreign market (has) led to the organization of the Pennsylvania Steel Company, and the parties who have connected themselves with it are determined to produce upon American soil all the principal manufactures of steel that are now, at such a serious cost for freight, commission, insurance, exchange, duty, etc., and often, with so much delay and uncertainty, imported from abroad. (We) are preparing to establish near the consumer, works at which articles of accustomed pattern will be promptly produced, and from the

Jan 1, 1971

By Lenny Winkel

With the aim to develop a solar-driven process for the extraction of copper from sulfide concentrates research on the decomposition of copper sulfides under inert atmospheres has been initiated. Thermogravimetric measurements on chalcocite,(Cu2S) revealed that copper is formed already at 1823 K. Chalcopyrite (CuFeS2) also disintegrates at this temperature, although at a lower rate. Copper and iron have been identified in the solid residue. The results confirm the feasibility of copper extraction by direct decomposition of sulfides under atmospheric pressure. The decomposition under inert atmosphere prevents generation of SO2, it also alters the behavior of volatile impurities during decomposition of copper sulfide concentrates. Chemical equilibrium calculations for chalcopyrite contaminated with enargite (Cu3AsS4) have shown that the absence of an oxidic slag allows for a complete evaporation of arsenic and subsequent separation from intermediate sulfides. The need to better assess the potential of direct sulfide decomposition has prompted the development of an experimental setup for studying the decomposition reactions. The experiment has been devised such that data on the decomposition kinetics and on impurity removal can be obtained at temperatures up to 2500 K.

Jan 1, 2003

By Thomas P. Battle

Titanium is the ninth most common element in the Earth's crust, yet only in this century has titanium come into use as an engineering material, particularly in aircraft structures, as the metal, and in pigments, as the dioxide. In this presentation, the metallurgical aspects of processing titanium-containing raw materials will be reviewed. Particular emphasis will be given to the ores and beneficiation techniques which lead to the production of titanium dioxide pigment, which accounts for over 90% of world titanium production.

Jan 1, 1993

By M. K. Quinn, A. W. Khair

"This paper presents an analysis of respiraple dust generation due to the action of a continuous miner. Underground coal cutting by a drum-type continuous miner was simulated in the laboratory using a specially designed unique automated rotary coal cutting simulator (ARCCS). An analysis of -400 mesh particles was done on gravity collected material. Samples of entrained dust were collected through the use of cascade impactors. Both samples were analyzed for size distribution and particle shape. Using the simulated coal cutter permitted variation of operating and in-situ parameters to provide information on the effects on generation of -400 mesh particles. In these tests coal blocks with an approximate dimension of 18 in. x 15 in. x 6 in. (45.7 cm x 38.1 cm x 15.2 cm) were first subjected to confining pressures, equivalent to in-situ conditions. Such blocks were then cut by the cutting head of the ARCCS, thus simulating the action of the continuous miner in underground coal mining. During the tests under a particular set of in-situ and operating parameters a number of other parameters such as 1) penetration of bit into coal, 2) penetration resistance (thrust and cutting pressures), 3) rotating velocity of cutting head, and 4) acoustic emission activity in the coal block were monitored. After each cutting cycle the fractured surfaces were photo¬graphed and a velocity survey was conducted by using a sonic technique. At the end of each experiment the cutting paths of the bits in coal were photographed using an optical microscope with an attached camera.IntroductionThe continuous-mining machines introduced in the 1950's now account for more than half the production of coal from underground mines. Unfortunately, these continuous miners, designed for increased productivity, have also increased the concentration of respirable dust in mines. As a result, the Federal Coal sine Health and Safety Act of 1969 was enacted to enforce on the coal operators that the airborne respirable dust not exceed 2 mg/m3, and was intended to reduce the incidence of coal workers pneumo-coniosis. This plus the other aspects of the legislation and the subsequent monitoring and enforcement by MSHA made it very imperative that the coal operators provide a relatively healthier and safer working environment for the coal miners. Since 1970, the Federal government has paid over 11.7 billion dollars to more than 470,000 miners with coal workers pneumoconiosis and their survivors (Newmeyer, 1981). These regulations, coupled with the assessment of the continuing burden on miners, the mining industry and taxpayers appear to have provided an impetus for the mining community towards comprehending the different parameters that influence dust generation and entrainment."

Jun 1, 1988

The Challenges in Mining _Large expensive assets that are not being utilised as well as they should _?Silo? operations plan, schedule and execute in isolation?poor visibility across the Value Chain _Disruptions or unforeseen events have serious upstream and downstream impacts _Exacerbated by multiple information systems, mostly spreadsheets _Strategic simulation (supply and demand) is often poorly Handled

Nov 1, 2011

By N. Cruickshank

Gas outbursts occur as sudden eruptions of gas and minerals from the face of a mine heading as the heading approaches potentially burst-prone (or anomalous) zones of rock. Such outbursts have resulted in considerable damage to equipment and in some cases lives have been lost. Characterizing these anomalous zones and detecting their presence is therefore vital to safe mining. Certain significant characteristics associated with the outburst-prone zones are: (1) the presence of fluid inclusions, (2) unstable stress conditions, (3) characteristic geologic structures, (4) certain physical properties of the rock, and (5) micro-seismic activity. Geophysical and engineering methods for detecting these characterisitcs are discussed and are considered with respect to their past success and future potential for predicting gas outbursts.

Jan 1, 1985

By Jr. Allan

"Although the advantages of large-capacity air receivers for underground mines are plainly evident from published information about various installations in the United States and abroad, details of their construction are not generally known in this country., Ordinary present-day air-compressor installations servicing mining machines are designed to supply air at a specified pressure in sufficient quantity to meet the peak demand of the mine,2/ although this demand may exist for only a few minutes out of 24 hours and, as usually happens, eventually exceeds the capacity of the compressor. Most of the receivers provided with these compressors (to a certain degree of standardi¬zation) are capable of storing a volume of air approximately equal to that compressed in 1 minute by the machine.3, 4/ As a result, during peak-load periods the compressor operates at full load capacity without maintaining kick-off pressure. At other periods of the work cycle, production of compressed air is intermittent.At least one large mine5/ has adopted large-capacity receivers to reduce wear on its air-compressing system caused by the sudden demand of peak loads. Under the old system, the compressors jumped suddenly from half speed to full speed; boilers furnishing steam to the compressors were taxed heavily to provide the increased requirements of power; and machines using the air, among which were four large hoists, were required to operate at 65 pounds per square inch rather than at the 90 pounds per square inch for which the compressors were regulated. Operation of air machines, especially drills, at pressures lower than those for which they were designed decreases their efficiency and increases maintenance costs. In addition, air that comes directly from the compressors has had little opportunity to cool and dry enroute.6./ As a result, quantities of compressor lubricant and water are carried into the machines that use the air. When expansion occurs in the cylinder or turbine of such engines, the temperature of the air drops, and this oil and water is precipitated. The water washes away lubricating oils in the machine, causing poor performance and high cost of maintenance; the compressor oil, in addition to being a poor lubricant for compresed-air engines, exerts a corrosive action on gaskets and rubber hoses.7/Reduction of peak demands on air compressors by large receivers lowers power costs by establishing more nearly constant load factors,8/ and in some cases by permitting the use of smaller compressor capacity.8,9/Load factor is the ratio of average demand to maximum demand; a low load factor costs money.10/Elimination of high-peak demands raises the load factor by making the average and the maximum demand more nearly equal. Further savings may be made possible by large receivers where their use permits charging to be done at night in regions having lower power rates during that period.11/Where ordinary receivers are used, compressor breakdowns cause immediate work stoppages in the mine owing to lack of air. Similarly, the capacity of a large receiver has been known to permit uninterrupted work in the mine until the compressors have been returned to service.9/Large-capacity receivers, either steel-tank or underground rock-chamber, offer a practical solution of many existing problems by providing a sufficient reserve of compressed air within the pressure range required for efficient operation of machines to level off peak demands on the compressor. The com¬pressors operate when the demand has reduced the pressure in the receiver below the regulating pressure and until all air used from the receiver has been replaced. It has been found possible in at least two mines,8.9/ one of which the author has visited, to entirely eliminate one compressor and to obtain more efficient performance from the remaining one by the construction of an underground coal-chamber receiver.8/"

Jan 1, 1950

By Milton B. Hall

This report discusses in detail laboratory and pilot-plant tests conducted from January 1951 until January 1955 at the Northwest Electrodevelopment Experiment Station of the Bureau of Mines, Albany, Oreg., on defluorination and recovery of evolved fluorine from phosphate rock. Results of use tests of defluorinated phosphate rock by cooperating agricultural colleges and the United States Department of Agriculture are also included. In 1954 the consumption of fluorspar, the only domestic fluorine-bearing mineral of commercial importance, was approximately 478,000 short tons; 245,000 tons was from domestic mines. The production of marketable phosphate rock in the same period was about 13,800,000 long tons. Of this total amount, approximately 15 percent was produced in the West. From the viewpoint of conservation and utilization of fluorine as a natural resource, it is interesting to note that the total estimated quantity of fluorine in domestically produced phosphate rock is more than double that present in domestically mined fluorspar.

Jan 1, 1958

By H. W. Dow

Quite early in the beginning of the present century, hoisting equipment underwent a radical change, when electric motors were applied to furnish the power in place of steam engines. Naturally, in the beginning, motors were not employed for large hoists: most of them were small single-drum hoists for which the motor ran continuously and the drum was clutched in for hoisting by various methods, and the down-going trips were made on the brake. In 1911 the Nordberg Manufacturing Co. of Milwaukee built for the first time a double-drum hoist powered with a first-motion direct-current motor (Fig. I). This hoist embodied many of the features that are used on larger hoists today. In the early development of motor-driven hoists a more or less natural mis- take was generally made, which only recently is being corrected. Because the electric motor has a higher speed than the steam engine, mining people in general accepted, without question, the use of small-diameter drums and the resultant finding of the rope in multiple layers, which was not at that time, the general practice on first-motion steam hoists. Small-diameter drums can usually be driven by a motor through a single reduction of gears even with relatively high motor speed, therefore the complete equipment could be obtained with a lower first cost.

Jan 1, 1946

Aur Resources is Canada's leading copper mining company with producing mines and development projects in North, Central and South America. Copper production from Louvicourt Mine in Quebec, Quebrada Blanca and Andacollo Mines in Chile was a record 245 million pounds in 2001. Located 600 km North of Montreal, Louvicourt Mine is a joint venture between Aur Resources (30%), Novicourt Inc (45%) and Teck-Cominco (25%). Aur Resources is the mine operator with 280 employees working to produce a copper and zinc concentrate. In operation since 1994, the mine has produced a total of 12,606,000 metric tonnes of ore grading 3.6% Cu, 1.5% Zn, 26 gr./m.t. Ag and 0.9 gr./m.t. Au. This highly mechanized mine reached full production in August 1995 at 4,000 tpd. From 1996 to 2001, the average mine production rate was more than 4,300 tpd. The Louvicourt Mine continued its record of solid performance in 2002 and is expected to continue to do so for the balance of its 2.5 years mine life.

May 1, 2003

By W. L. Saunders

It is now generally admitted by experts that at least so far as rapid progress is concerned the Alpine system of tunnel-driving is superior to any other. This is perhaps natural in view of the record of experience in driving tunnels through the Alps. These great mountain-chains cannot be treated in the ordinary way by shaft-sinking and driving headings, thus multiplying the points of attack. The work must be done from the ends only, hence speed in driving is of the utmost importance ; and, as necessity is the mother of invention, the concentration of effort to make progress has resulted in an organization and in mechanical appliances that have produced results so much in excess of the usual practice, even in America, that a discussion of the subject in detail should be of much value to the engineer and contractor. The first Alpine tunnel mas the Mont Cenis, length 7.5 miles, driven with a progress that averaged about 7.75 ft. per day. Next came the Saint Gothard, 9.5 niiles long, 18 ft. per day; Arlberg, 6.5 miles long, 27.25 ft. per day; Simplon, 12.25 miles long, 36 ft. per day. The figures represent progress when driving from two headings, so that by dividing them in two we get the daily single-heading progress. The latest of the Alpine tunnels is the Loetschberg, now being driven. In this work the world's record has been beaten by a single day's record in one heading of 36 ft. and by an average daily record in one heading of 29.5 feet. The Alpine range forms a natural barrier between a large section of northern and southern Europe. This range extends from the southeast of Prance to the frontier of Hungary, betveen Italy and the plains of sonthern Germany. The contour

Jan 1, 1912

By S. J. Aresco

The Bureau of Mines has been active in promoting the purchase of coal for Government use under specificetiona that define the requirements in terms of heating value of the coal, expressed in British thermal units, and the composition as shown by proximate analyses. To these, when required, are added the fusing temperature of ash and the free-swelling index. Under most of these specification contracts the bidders guarantee the quality of the coal, end that guaranteed by the successful bidder becomes the standard of his contract. The deliveries are sampled in accordance with instructions3/ issued by the Bureau; the samples are analyzed in the Bureau's laboratory to determine whether the coal is of the quality guaranteed by the contractor and, if it is not, a price adjustment is made. Analyses of the delivered coal and "tipple" samples (samples collected at mine tipples as coal is being loaded into railroad cars or trucks) provide valuable data for use in evaluating future bids. In addition, the continuous sampling of coal as delivered 1s a check on the practical results obtained in burning the coal.

Jan 1, 1953