Search Documents

By T. S. Bomar, C. J. Wood

Heavy media cyclones (HMCs) are efficient, high-tonnage devices suitable for upgrading run-of-mine coal in the 50 to 0.5 mm size range. Unfortunately, industrial HMC circuits are often not optimized due to problems such as incorrect operating pressures, poor feed distribution, excessive media contamination, mismatched components, and improper density control. To avoid these problems, operating guidelines have been provided in this article that are useful for optimizing the performance of HMC circuits. The validity of these guidelines has been assessed by means of density tracer tests carried out at several coal preparation plants.

Jan 1, 2002

By J Gresham, A Turichshev

Ore from Henderson’s 7700 Southwest panel cave is transported between the production and truck haulage levels through a series of orepasses. A typical orepass complex consolidates dump points from four production drifts into two long bored raises feeding into a single truckloading chute. The system typically covers a vertical extent of 200 m and a lateral extent of 90 m. In the process of commissioning several initial orepass complexes, challenges with preferential draw in the long bored raises were observed. Preferential draw occurs when one long orepass mobilises much sooner and/or flows significantly faster than the other orepass. This has negative implications for orepass availability in the production drifts. As future mining at Henderson relies on the construction and use of such orepass systems, the development of appropriate design criteria and practical solutions to existing flow problems was necessary.A series of PFC3D numerical models were developed to assist in identifying the factors influencing preferential draw and possible corrective measures. The models helped to identify two primary factors that caused the preferential effect: the relative elevation of the brow at the bottom of each long bored raise, and the location of the bin used to funnel fragmented rock from both raises into the chute. This paper covers the initial design of the orepass complexes at Henderson, results of the numerical models, mitigation work done to date on existing orepass complexes, and design criteria for future construction.CITATION:Gresham, J and Turichshev, A, 2016. Correcting preferential flow problems in long orepass systems at Henderson Mine, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 549–554 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By R. R. Tatiya

Data obtained from a copper mine were used in a comparative study of the reserve estimates generated by applying geostatistical methods to surface borehole data, underground core drilling results and assay values from chip sampling. Global estimation of the deposit performed by kriging of the low-density sampling data from the surface boreholes did not provide reliable results, but could identify the potentially mineralised zones. The reserve generated from core drilling results correlated well with that estimated from chip sample data and with that estimated by the conventional methods used at the mine. A satisfactory reserve evaluation could, therefore, be obtained by kriging of the data from the underground core drilling alone, provided that a systematic sampling procedure was adopted. Estimates based on chip sampling information could be used as a check, which could avoid the current practice of chip sampling of most of the mine workings. The aim should be to develop a semi-variogram for the deposit, which could be used to estimate the reserves by kriging

Jun 19, 1905

By Naoki Hosoya, Setsuo Maeda

This paper addresses establishment of an experimental system for measuring biodynamic response (BR) of hand-arm system at the NIIH in Japan. BR measurement system at the NIIH is nearly equivalent to NIOSH installed system. The feasibility of the system is examined through the apparent mass (AM) measurement of the empty handle and a set of calibration masses. Apparatus The grip force was measured by using the handle shown in Fig. 1. The handle has two force sensors (KISTLER, 9212) and one accelerometer (PCB, 356A12). A low-pass filter with 5 Hz cut-off frequency was used to the grip force from measured force signal. Figure 2 shows BR measurement system in this study. The push or pull force at the handle was measured by using the force plate (KISTLER, 9286AA). The grip force and the push / pull force were displayed on a monitor. The shaker (IMV, VE-100S) is used to vibrate the hand-arm system along the forearm axis (Zh direction) (ISO 10068, 1998; ISO 5349-1, 2001). In most situations force actions for operating tools are expressed by grip, push, pull and combined these actions. These actions can be simulated in the test system. AM was obtained by performing H1 estimator in the PULSETM system (B&K, 3109) and it is denoted at the one-third octave band center frequencies. [ ] Methods In order to investigate the reliability of the system, AM measurement of the handle was performed. It is assumed that the handle is rigid in the upper limit of adoptive frequency range in this study. This assumption is validated in AM measurement of the empty handle. A pseudo-random vibration in the frequency range of 10 to 1,250 Hz was used and its amplitude is 1.0 (m/s2)2/Hz with a flat power spectral density (PSD) in the experiment. Measured AM includes the mass effect of the measuring cap in a subject experiment. Compensated apparent mass AMc(?) is obtained by Eq. (1) 1-2.

Jan 6, 2006

By S. Frimpong

Shovel excavation constitutes a significant component of production costs in any surface mining operation. This makes shovel loading an important cost center that needs to be improved to lower production costs. Optimization of tool design will improve energy efficiency in earthmoving operations. However, modeling the soil-tool interaction is a complex process due to the fact that forces for excavating particulate material are functions of many variables. The magnitude of this resisting force depends not only on the type of soil but on the size, shape and orientation of the cutting element. Moreover, part of this complexity is attributed to the fact that the behavior of the material during excavation is not yet well understood. For the past five decades, researchers have mostly used the passive earth pressure theory to study the soil failure patterns around a cutting tool and to develop force prediction models for design optimization with some success. Although the force models developed from the passive pressure theory have been successful to some extent, they can hardly be extended to a general case because of the underlying assumptions and simplification of tool shapes. This paper aims at reviewing some of the existing empirical and analytical methods of cutting and excavation tool modeling with a focus on their merits and limitations. The paper also explores the use of numerical methods, specifically the discrete element method, for dealing with the unresolved aspects of soil dynamics in excavation.

Jan 1, 2011

By A. R. Denison

The area discussed in this report comprises a group of 38 counties lying in the northeast corner of Texas. It covers all, and extends beyond, the borders of what is commonly described as the East Texas Basin. It includes two major oil fields, Van and East Texas; two major gas fields, Bethany and Waskom; and a number of fields, both oil and gas, of lesser importance. All commercial oil production comes from beds of Upper Cretaceous age and almost exclusively from the basal member, the Woodbine sand. Gas is produced from both Upper and Lower Cretaceous beds with the newer production from the older beds. East Texas Field This field continued as in 1932 and 1933 to dominate the drilling and production situation throughout the oil business. A total of 3681 producing wells was completed in this field during 1934. This is an increase of 1215 over the 2466 producers completed during 1933. Total wells

Jan 1, 1935

By G. F. Kuncir

The time-cost-risk analysis described herein was performed as part of an evaluation of the Advancing Oil Shale Mining Technology Program performed by The Aerospace Corporation. The objectives of this analysis are to assess the feasibility of the program relative' to time and cost constraints, and to determine the probabilities of achieving various technological goals. A combination of standard program planning and analysis techniques were used to achieve these objectives. These included a critical path analysis, a resource allocation analysis, and a risk analysis.

Jan 1, 1977

By S Henderson, J V. Lawless

The worldwide association of low-sulfidation epithermal gold mineralisation, bimodal rhyolitic-basaltic volcanism and rifting is confirmed in New Zealand. In the currently productive Coromandel epithermal-gold province reported Ar-Ar dating of adularia from low sulfidation deposits falls into two groups at 6 and 7 Ma. Bimodal rhyolitic-basaltic volcanism has been reported to be K-Ar dated at 9 to 7 Ma and 6 to 5.5 Ma. Epithermal gold mineralisation in Northland is spatially associated with bimodal basaltic-rhyolitic volcanism, with rifting cogenetic with that in the CVZ. The Taupo Volcanic zone (TVZ) is sufficiently young that the presence of a segmented rift with recent bimodal rhyolitic-basaltic volcanism can be genetically associated with epithermal gold mineralisation, which occurs as both fossil occurrences and in active geothermal fields. This reinforces the known potential prospectiveness of the Coromandel area and increases that of Northland and the Taupo Volcanic Zone.

Jan 1, 2005

By M. A. Leosson, S. H. Bottrell, R. J. Newton

Sylvite at Boulby is mined 1 140 m beneath the sea and the mine suffers from the influx of water. This is of two kinds: persistent flows originating in the Sherwood Sandstone aquifer and entering the evaporite sequence through fractures in the intervening mudstone, and impersistent flows which are transient in nature and of uncertain origin. Water from the overlying sandstone has become enriched with NaCl and large amounts of KCl and some Mg and Br have been added by interaction with the evaporites. Waters from the transient flows are isotopically distinct from those in the Sherwood Sandstone, being enriched in H and O. They are also saturated with respect to halite and sylvite, but have higher K/Na than the persistent flows and are much more enriched in Mg and Br

Jun 18, 1905

By I. L. Nichols

The Bureau of Mines is investigating vanadium recovery from various domestic resources. A low-grade carnotite ore sample containing 0.34 pct V20S and 0.04 pct U30S was leached, and the results were compared with those of similar leach tests using a mill-grade sample containing 1.26 pct V205 and 0.19 pct U308. Experiments on the two ore samples included agitation leaching, pugging, salt-roast leaching, and autoclave leaching. None of the leaching methods investigated showed any significant advantage over another except autoclaving, which reduced the leach time but at the expense of greater acid consumption. Typical of the experimental results attained are the data gathered from the agitation leaching tests. Agitation leaching of the mill-grade ore with 100 lb/ton H2S04 resulted in extractions of 94 pct U308 and 33 pct V205. To increase the vanadium extraction from 33 to 91 pct required concentrations of 300 lb/ton H2S04 and 10 lb/ton NaC103. Complementary agitation leach tests on the low-grade ore required 200 lb/ton H2S04 to extract 94 pct U308, and 300 lb/ton H2S04 and 10 lb/ton NaC103 to extract 90 pct V205.

Jan 1, 1983

Experimental studies on viscosity of titanium bearing slags have been reviewed and the assessed data were used in extending the capability of the structurally related viscosity model for silicate melts, developed by the present authors. Experimental data on ternary and higher order systems containing CaO, MgO, MnO, FeO, Al2O3, TiO2, Ti2O3, SiO2were assessed and used. The newly extended viscosity model represented the viscosity behaviour over broad temperature and composition ranges. The structural role played by TiO2and Ti2O3in silicate network structure is discussed with respect to their effect on viscosity of melts. Keywords: viscosity model, TiOx containing silicate melts, silicate network structure.

Jan 1, 2004

By R. W. O. Kersten, J. D. Austin

A questionnaire was circulated in 1986 that had the objective of establishing the type of material that members would like to see featured in the Journal of The South African Institute of Mining and Metallurgy. The questionnaire contained five main questions involving the following:

Jan 1, 1987

By A. L. Grabovski

The potential of eccentric cone crushers for fine crushing has been improved by increasing the swing frequency of the moving cone, balancing the crusher, ensuring uniform feed via a rotating funnel with sideways discharge, introducing hyperbolic motion and employing the inertia crushing method, but further improvements to the specifications of existing cone crusher designs are limited by the rigidity of their kinematic coupling. A new design has been developed which combines two crushing modes, stone on liner and stone on stone, each with its own advantages. The main aims are to produce finer materials and to reduce liner weight. The benefits include an increase of more than 10% in the output of fine particles, improved protection of the liner against wear, as a result of filling of the cavities by material being crushed, and the use of almost 20% less material in casting of the liner. The chamber can be used in place of the usual liners of fine cone crushers

Jun 21, 1905

By Jeanne A. Smith, Suzanne D. Smith

Annoyance, fatigue, and musculoskeletal pain have been reported during prolonged exposures to propulsion-generated vibration in military propeller aircraft1. The objective of this study was to determine the vibration mitigation properties of selected seat cushions and the effects of occupant seating posture during exposure to higher frequency multi-axis vibration associated with military propeller aircraft. Methods A Navy E-2C Hawkeye crew seat was mounted onto the Six Degree-of-Freedom Motion Simulator (SIXMODE). Six seat pan cushion configurations were tested during exposure to an E-2C vibration signal collected in the field1. Seat pan cushions 1 – 5 were used with the original E-2C seat back cushion. Cushion configuration 6 included seat pan cushion 5 with a prototype seat back cushion. Triaxial accelerometer pads were mounted onto the seat pan and seat back cushions to measure the vibration entering the human. Data were collected for seven subjects seated upright with their backs in contact with the seat (back-on) and not in contact with the seat (back-off). Spectral analysis techniques were used to analyze data at the two dominant frequencies associated with the propulsion system (propeller rotation frequency (PRF) ~18.5 Hz, and blade passage frequency (BPF) ~73.5 Hz). Overall accelerations were also calculated between 1 and 80 Hz. Vibration Total Values (VTVs) were calculated using the weighted seat pan and seat back (back-on only) accelerations and compared to the comfort reactions given in ISO 2631-1: 19972. Results In general, the highest accelerations observed at the seat pan occurred in the fore-and-aft (X) direction at both the PRF and the BPF for all cushions and both postures. The most pronounced effect was at the BPF in the X direction, where all configurations showed significantly lower seat pan accelerations than configuration 1 (original E-2C cushion) with the back-on posture. Configuration 5 was the exception with the back-off posture (Fig. 1A, Repeated Measures ANOVA, P<0.05). The most pronounced effect of posture occurred at the PRF in the X direction, where all cushion configurations showed significantly lower seat pan accelerations with the back-off posture (Fig. 1B). All configurations except configuration 2 showed similar VTVs as compared to Configuration 1 (Fig. 2, P<0.05). Configuration 2 tended to show the lowest weighted acceleration levels. The overall VTVs (back-on only, Fig. 2B) showed significantly higher accelerations as compared to both the back-on and back-off seat pan point VTVs (Figs. 2A &

Jan 6, 2006

To George Orwell the year of 1984 was the inspiration for a book. To most New Zealanders it was the year that the fourth Labour Government was elected to power. It was also the year that the review of mining legislation commenced. While Orwell&apos;s book and the election of Labour are clearly events of some historic note, one could be excused for classifying the review of minerals legislation somewhat differently in terms of its present achievements! Since the review began it has led a tortuous path through a rapidly evolving policy environment to a point three years hence where no major policies have been determined.

Jan 1, 1987

By M. Grun, A. C. Marlowe, I. Littleford

SYNOPSIS A Wirth tunnel borer owned by Anglo American Corporation completed a 1150m long tunnel some years ago and was subsequently extensively modified by Technical Development Services. In 1982 this borer provided new and particularly interesting information In the field of hard rock boring. The abrasive quartzltes traversed proved to be a challenge to the cutter manufacturer and the project team. This paper examines the problems faced, the solutions found and the lessons learnt.

Jan 1, 1983

By Don] [Hinkle

Unable to Load

Jan 1, 1977

By Alan D. Akerman

This paper describes the significant advantages and improvements in operational availability, reduced breakdowns, and overall cost reductions that can be achieved through the application of a Reliability Centred Maintenance (RCM) program, including Condition Based Maintenance (CBM) and Equipment Health Monitoring (EHM), in a mine environment. It uses a case study to illustrate the essential elements that constitute the basic requirements to establish such programs. This CBM case study analyzed the Load-Haul- Dump (LHD) vehicle sub-systems and their dominant failure modes, as a precursor to the development of condition indicators. The case study describes a disciplined process to enable condition indicator development and qualification in support of a CBM program. The identified condition indicators vary from readily applicable off-the-shelf monitoring systems and techniques, through to "leading edge" technologies that require further research and development. The paper also explores the developments that have been made in the combination of expert system software associated with modern computer based control systems, and the availability of "intelligent? sensor technology that complement the control system capability.

May 1, 2002

By F. N. Kissell, C. D. Litton

Abstract-This study predicts the level of smoke that miners might meet while trying to escape a coal mine fire and describes how smoke would impede their safe escape. For this study, the authors assumed that miners exit through an escapeway adjacent to the burning entry, that some air would leak from the burning entry to the escapeway. The following conclusions were made: • A very low amount of air leakage to the escapeway can produce a critical level of visual obscurity from smoke. This shows that intake airways may be as susceptible to smoke visibility problems as return airways. • This critical level of smoke obscurity is reached much before a critical level of carbon monoxide is reached. • Small fires can cause a severe sensory irritation that further limits vision. Thus, reliable eye protection is very important. These results show that methods to guide miners through dense smoke will contribute greatly to saving lives during mine fires.

By John Rusnak

The Coal Mine Roof Rating (CMRR) is a practical rock mass classification system for use in design of mine openings. Data can be obtained for this purpose from exploration drill cores if simple geotechnical logging and rock mechanics testing is conducted. The CMRR is an excellent method to quantify rock characteristics for engineering purposes. It bridges the gap between geologic description and engineering design. The CMRR was utilized in the design of a 10,000 fl. long coal belt conveyor tunnel connecting an Eastern Associated Coal Corp. mine and preparation plant in Boone County, West Virginia. Data gathering and analysis techniques are discussed involving the calculation of the CMRR and its application in the design of the tunnel, which was driven through a thin coal bed zone. The preliminary findings have correlated well with actual roof and mining conditions encountered during driving the tunnel and it is concluded the CMRR is an effective method to utilize geologic data from exploration core holes for engineering analysis and design.

Jan 1, 1998