Search Documents

By Jerry E. Olson

In 1984, the U.S. Bureau of Mines conducted a mineral survey of the Pahute Peak Wilderness Study Area (WSA) (NV-020-621), which covers 57,529 acres in Humboldt County, NV. About 90 percent of the WSA is underlain by Tertiary volcanic and shallow intrusive rocks. Of the remainder, metasedimentary rocks of unknown age are in contact with Cretaceous intrusive rocks in the northwest corner of the WSA. The entire WSA is within an upthrown fault block of the Basin and Range physiographic province. Portions of the WSA, especially south of Pahute Peak (Big Mountain), may be part of an eroded caldera structure. No mines or evidence of major exploration were identified within the WSA. Workings in Copper Canyon, claim blocks along the northwest boundary, and zones of anomalous character as defined by the Bureau of Land Management were examined. No mineral resources were identified, but sample results indicate three significantly mineralized sites, one with indications for zinc skarns in Copppr Canyon, another favorable for precious metals 2 miles south of Copper Canyon, and another area near the northwest boundary with geologic conditions characteristic of molybdenum deposits. Further investigation of these sites is warranted. Petrified wood is present in small amounts near the west central range front.

Jan 1, 1986

By Ian MacKenzie

Over the past twelve years, professionals such as architects, engineers, accountants, and attorneys have not had to pay a great deal of attention to GST. The fees charged to clients (outputs) have not been subject to GST, but they have had to pay GST on al purchases of materials and taxable services relating to their activities.

Jan 1, 1990

By C. Ozgen Karacan, William P. Diamond

In This Chapter [Measuring the gas content of coal Predicting gas emissions based on geologic and coal reservoir property data Determining the gas storage capacity of coalbeds and other gas-bearing strata Methane drainage borehole monitoring to forecast the remaining gas-in-place and the influence on mine emissions Forecasting gas emissions during mining as a function of mining parameters and Gas emission prediction based on numerical simulation] This chapter provides guidelines for determining the gas content of coalbeds, estimating the gas-in-place, and predicting gas flow and emissions before and during coal mining operations. The techniques are discussed briefly in the following sections. However, detailed information on the techniques is provided in the cited references. INTRODUCTION Coalbed methane, if not properly controlled in the underground mine environment, is a safety concern due to the potential risk for an explosion. This is a particular problem during longwall mining, where the high rate and volume of coal extraction can result in the release of large amounts of methane from the mined coalbed and other adjacent gas-bearing strata. The variability and potential hazards of these sometimes unexpectedly high gas flows provide the impetus to develop methods to predict methane emissions into the underground workplace. A forecast of the volume of gas that might be released during coal mining is helpful for designing ventilation systems and for implementing optimum methane drainage strategies to help mitigate expected gas emission problems. A complete assessment of the need for methane drainage prior to mine development generally requires both an empirical and a theoretical approach. If there are active mines in the general area with similar geologic conditions and coal characteristics, a review of gas problems in those mines provides an initial insight into the level of gas emissions to be expected at a new location. In addition, relatively simple methods exist to determine the in situ gas content (volume of gas per unit weight of coal) of the coalbeds in a particular mining area, as well as the gas-in-place (volume of gas in the coalbed(s) within a defined geographic area).

Jan 6, 2006

By S. Lähteenmäki, P. Koivistoinen, J. Levanaho

Semi Autogenous Grinding (SAG) circuit is the most common grinding circuit to day. In Europe and South Africa fully autogenous (AG) circuits are also popular. SAG circuit has a lower capital cost and simple operation. SAG circuit requires the use of grinding balls, which increases operating costs and decreases availability. An AG circuit may produce a higher Net Present Value to the investment. The AG circuit is more complex to design and operate. However, operating experience from AG circuits illustrates that an AG circuit can be as trouble free as a SAG circuit with the benefit of lower operating cost.

Jan 1, 2001

By Rolland R. Mates

This paper describes the use of post- tensioned rock anchors to reduce the risk of future damage to a residential structure as a result of coal mine subsidence. The project described in this paper was performed by the Office of Surface Mining Reclamation and Enforcement (OSMRE) of the U. S. Department of the Interior. The OSMRE was created to administer Public Law 95-87, the Surface Mining Control and Reclamation Act of 1977. The responsibilities of OSMRE include "reclamation and restoration of land and water resources, adversely affected by past coal mining including prevention, abatement, control of coal mine subsidence. ?('l) Consequently, OSMRE has been addressing mine subsidence problems since its initial subsidence stabilization project in 1979. Stabilization activities have primarily consisted of supporting the overburden material by injecting materials through drilled bore holes into the underground mine voids. Injection of various materials into mine voids, including fly ash mixtures, coal refuse, cement grout, and gravel has proven to be a successful method of reducing mine subsidence-related surface movements, and has been extensively utilized in mitigating mine subsidence problems. However, the cost of drilling for injection can be extremely high in areas where the depth to the coal seam is great.

Jan 1, 1986

By R P. Bewick

Many future and current block and panel caves extract ore from veined rock masses. These rock masses are composed of open joints forming blocks or rock with healed networks of veinlets. These two types of discontinuities pose a challenge for rock mass characterisation and classification due to difficulties in distinguishing actually open joints from healed but weak veins when diamond core drilling and excavation blasting practices disturb the rock mass. The inability of separating characteristics of open joints and healed veins has often resulted in an underestimation of the rock mass quality and as a consequence led to inappropriate assessments of rock mass response to mining (ie rock mass behaviour) and consequently deficient excavation stability assessments and ground support designs. In this paper, guidelines are provided to improve the characterisation and classification of veined rock masses. It is shown how veined rock masses can be mischaracterised resulting in often incorrect forecasting of rock mass behaviour. Following this, the classification of veined rock masses is examined. It is shown how the primary classification systems (ie Q – Barton, Lien and Lunde, 1974; rock mass rating (RMR) – Bieniawski, 1976) may not lead to reliable ratings in veined rock masses if care is not taken to differentiate between open joints and veins of varying strength. Examples are provided to illustrate how the Q and RMR systems are insensitive to veining. Finally, an example of characterising a veined rock mass for design purposes is presented.CITATION:Bewick, R P and Kaiser, P K, 2016. Characterisation and classification of veined rocks for rock mass behaviour assessment, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 825–834 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By G. S. Scott

In the course of the Bureau of Mines investigation relative to the causes, behavior, and control f anthracite-mine fires, attention was directed toward the correlation between the temperature of oxidation and the gaseous oxidation products in the range of temperatures between 100° and 350°C4/ These tests, made on a high-grade anthracite to determine the amount of oxygen consumed and the amounts of carbon dioxide, carbon monoxide, hydrogen and methane evolved when air was passed through samples of the anthracite at various elevated temperatures, showed that the gases evolved and their relative proportions vary with temperature, constitute a means for determining the probable temperature of the anthracite, and thus permit detection of incipient heating before a dangerous fire hazard exists. As the relationships mentioned are affected somewhat by the amount of previous oxidation of the coal, it was deemed desirable to know to what extent they might vary owing to this cause. It was also considered desirable to have a means for estimating the extent of oxidation from the gas analysis, as this would permit a more accurate estimate of probable temperature. Finally, it seemed desirable to know how much the composition of coal might vary over an extended period of oxidation, since this was previously suggested5/ as a possible means for estimating the probable maximum oxidation temperature to which a sample of coal had been subjected.

Jan 1, 1940

By S. Slottee

The technology of making and using ?paste? from mine tailings is increasingly well known by the minerals industry. The primary applications are water recovery and ?stacking? of tailings with minimal use of dams and ponds. This paper highlights some applications, other than water recovery and stacking, that have come to the attention of a paste thickener equipment supplier. As generated by thickeners, paste (also called ?thickened tailings?) is a non-settling, relatively high concentration, suspension of solids that can be pumped. Paste deposits with an angle of repose, allowing minimal use of dams. High solids concentration allows more water recovery at the paste thickener than is achieved in conventional and high rate slurry tailings thickeners. This paper is based on paste as produced in a flow sheet that includes a thickener, underflow pumps that are typically centrifugal, transfer pumps that can be centrifugal or positive displacement, and a distribution system at the deposition site. Examples of paste applications other than water recovery or stacking include: ?mine? an existing tailings pond by removing slurry, recovering coal or iron ore values, and return the new tailings to the pond as a paste that does not res-suspend; use paste to seal an existing tailings pond from leaking to groundwater or to an underground mine; extend the life of an existing tailings pond by thickening the tailings to paste; move an existing dry tailings impoundment to a new location by slurrying, pumping, paste thickening, and redeposit; minimize the size of a filter by paste thickening the feed; operate a paste thickener and filter in parallel on a tailings stream with re-mixing to achieve a high solids concentration. The use of paste tailings technology has been expanding over the last 15 years. The applications, both implemented and under consideration, are increasingly diverse and include all minerals tailings. Tailings handling designers should always consider a paste option to the conventional slurry solution.

Jan 1, 2011

By Nikolas K. Sokol

Underground construction often requires working within a very congested urban environment, including excavating shafts adjacent to highly sensitive and multistoried structures, sometimes even within such structures. Shafts adjacent to heavily loaded column footings are often required due to space constraints. Invariably, footing surcharges must be considered during the design of shaft rock reinforcement. Rockwedge stability evaluation reveals that column surcharges can greatly impact the ability to meet the desired factor of safety. Design methodologies and examples to deal with these special circumstances are presented.

Jan 1, 2008

By M. Suzuki, T. Shiomi, M. Nakada, K. Tsutsumi

Mold powder plays an important role in the continuous casting process for high quality steel production. It is well known that mold powder entrapment causes surface defects in steel sheet and the high viscosity of mold powder prevents the entrapment of mold powder in molten steel in ultra low carbon steel. This paper deals with the entrapment of mold powder caused by suction by Karman?s vortex in a laboratory experiment. At first the effect of the viscosity of oil and interfacial tension between water and oil was investigated in a water model experiment. Then hot model experiments were carried out by mold powder and molten steel. The amount of mold powder entrapment was affected by the viscosity and the interfacial tension between molten steel and mold powder. As a result, the following equation of the mold powder entrapment was obtained. m=1.06*107?-0.255?m-s-2.18 The amount of mold powder entrapment decreased when the viscosity and interfacial tension increased. But the effect of viscosity was larger than that of interfacial tension in the case of the industrial mold powder when the viscosity was under 0.5 Pa.s, interfacial tension was from 1200to 1300 mN/m.

Jan 1, 2004

By H. K. Lin

Residual cyanide in cyanidation tailings can be detoxified by its oxidation to cyanate, as in the Inco and Degussa processes. However, cyanate, the product of detoxification and other oxidation processes, may be reduced to cyanide in reducing environments, e.g., deepwater discharge of cyanidation tailings. This study shows that the reduc-tion of cyanate to cyanide occurs and that the reduction rate increases with decreasing solution redox potential. Solutions with lower pH favor the reduction rate. No significant difference was observed between the results of tests prepared with distilled water and seawater, and the presence of cyanidation solid tailings does not show an effect on the reduction. Because cyanate can be reduced to toxic cyanide, causing environmental concerns, the deepwater discharges of cyanidation tailings must be handled carefully.

Jan 1, 2008

Frothing in Seawater Flotation Systems

Sep 13, 2010

By K. M. Connor, O&apos

Variations in overburden geology must be considered in applying subsidence prediction methodologies developed by the U.S. Bureau of Mines (USBM). To characterize rock mass overlying high-extraction coal mines, the USBM utilizes a computer spreadsheet program and modified Rock Mass Rating (RMR) system. The spreadsheet calculates an RMR based on a bed's engineering properties determined from core logs and laboratory tests. An in situ deformation modulus and a bending stiffness are computed for each bed. Stiffness-versus-depth plots identify groups of beds with similar stiffness. Large variations in stiffness between adjacent beds are considered significant horizontal discontinuities where slip is likely. Time domain reflectometry (TDR) is used to verify this hypothesis by measuring shear displacement along such discontinuities. A model of the overburden is built by assuming that a near-surface laminated beam exists above a transition zone in which large plastic slip occurs along horizontal discontinuities. Increasingly thicker groups of beds are modeled to determine the most probable beam thickness based on a comparison with measured deflection profiles. The inverse of maximum beam deflection is an index parameter known as "bridging potential," a single value that incorporates both overburden geology and mine geometry.

Jan 1, 2010

By S. Pinard, J. MacLellan, G. Ehlert

"The Kidd Creek concentrator is looking actively for alternative technology as means of reducing operating costs in their concentrate handling section. The use of pressure and vacuum filters to eliminate the multiple hearth dryers would have the most beneficial effect. The dryers which constitute the greater portion of concentrate drying costs consume about 35,000 m3 per day of natural gas.After the evaluation of various filters by Kidd's technology group, it was clear that, because of the low final moisture requirements of 5.5 to 6% H20, few filters were able to achieve this target economically. Lately attention has focused on the Andritz hyperbaric filter. Testwork has shown that target moistures can be achieved with an appreciable reduction in operating cost.1.0 INTRODUCTIONThe Kidd Creek Concentrator is located 28 kilometers east of Timmins, Ontario. The ore is hauled by the Kidd Creek Railroad to the concentrator where it is milled to produce separate copper and zinc concentrates.Projected concentrator feed for 1991 is 3,750,000 tonnes of ore grading 3.3 % Cu and 4.7 % Zn. The concentrate production is expected to be 458,080 dry tonnes of copper concentrate at a grade of 25.7 % Cu and 265,020 dry tonnes of zinc concentrate at a grade of 54 % Zn.Currently, there is active investigation toward cost reduction through implementation of new technologies. One area which has been extensively evaluated is the concentrate dewatering and drying section. In that section, the multiple hearth concentrate dryers represent the largest source of operating costs, mainly through maintenance and energy costs (electricity and natural gas). The replacement of these dryers with filtration technology that could produce the required concentrate dryness would represent substantial savings.In September of 1990 filtration testwork carried out by Andritz Ruthner showed that Kidd Creek copper and zinc concentrates could be filtered to below 6 and 8 % moisture respectively. In late May 1991 the laboratory testwork was duplicated on siteand one month later a 5 m2 pilot filter was tested on site. Based on the pilot test results, an economic evaluation was performed. It indicated that a reasonable payback could be realized if hyperbaric filters were to replace the existing concentrate drying section."

Jan 1, 1992

By C. Demir, M. S. Celik, I. Gülgonul

Na-feldspar (albite) and K-feldspar (microcline or orthoclase) are major feldspar minerals with identical crystal structures and physicochemical properties. Flotation appears to be a unique method of separating these minerals. Fundamental studies on amine/feldspar system in the presence of monovalent salts showed that separation of these feldspar minerals by flotation is possible at certain concentration of monovalent salts in HF medium and natural pH. A comparison between natural pH and HF medium indicates that the latter provides a better selectivity at the expense of higher collector requirement. A general mechanism for both systems involving an ion exchange between the uncommon ions and adsorption of the common ions is proposed to be responsible for creating differences in the charge of albite and microcline unto which amine adsorbs.

Jan 1, 2002

Steady increases in longwall production have required operators to apply greater quantities of ventilating air in an effort to control and dilute respirable dust. Significant increases in shearer speeds necessitate that longwall supports also be advanced at a faster rate. Both of these factors may contribute to overall respirable dust levels on the longwall face because as supports are lowered and advanced, broken material falling from the top of the canopy is entrained directly into the air stream. To address this issue, the Pittsburgh Research Laboratory collected respirable dust samples from four longwall faces to characterize shield-generated dust. This paper investigates the influence of air velocity and shield advance rates on respirable dust levels. Also discussed are engineering controls currently used to reduce shield dust and alternative controls being investigated by the National Institute for Occupational Safety and Health (NIOSH).

Jan 1, 2009

By Guangyi Sun

Wall rock classification method for coal mine support is the main factor affecting mine support. It is greatly affected by the combined effect of randomness, fuzziness and human being's incomplete knowledge. There are several coal rock classification methods. Using different rock classification methods the same engineering rock mass can be classified into different classification leading to different construction practices.

Jan 1, 2005

By S. M. Spottiswoode, J. A. L. Napier, M. Kataka

The move away from the use of strike stabilising pillars at depth and the adoption of the more flexible system of mining towards final dip remnant pillars brings new opportunities for optimising mine design. In the initial planning stage, the size and spacing of the final pillars is designed using classical design criteria, through limiting modelled values of Energy Release Rate (ERR), Average Pillar Stress (APS) and Excess Shear Stress (ESS). In reality, mines often leave pillars that are larger than those originally designed. One of the reasons for leaving more ground is an unexpectedly high rate of seismicity. In this paper, we present developments in integration of modelling and seismicity that are aimed at developing design criteria that are more responsive to local conditions.

Jan 1, 2003

By Lawrence K. Barker

Crude shale oil produced by underground retorting of Green River Formation oil shale was hydrogasified over a cobalt-molybdate-on-alumina catalyst at operating temperatures ranging from 800° to 1,300° F, pressures of 500, 1,000, and 1,500 psig, and a liquid hourly space velocity of 1.02 volumes of oil per volume of catalyst per hour (Vo/Vc/hr). At a temperature of 1,300° F and pressure of 1,500 psig, 94 weight-percent of the liquid feed was converted to gas containing 72 volume-percent methane. With two reactors in series at a temperature of 1,170° F in reactor 1 and 1,260° F in reactor 2 and a pressure of 1,500 psig, 97 weight-percent of the liquid feed was converted to gas with a methane content of 75 volume-percent. Liquefied petroleum gas (LPG) was hydrogasified at operating temperatures ranging from 500° to 1,400° F at a pressure of 500 psig over a cobalt-molybdate-on-alumina catalyst. Similar experiments were made with an empty tubular reactor. The data indicate that gasification reactions in the presence of a cobalt-molybdate catalyst change from predominantly a catalytic (carbonium ion) reaction to predominantly a thermal (free radical) reaction at temperatures greater than 1,100° F. The data also indicate that a reaction temperature of 1,350° F is necessary at the space velocities used in this investigation to make a synthetic natural gas (methane content of 90 volume-percent) from in situ crude shale oil.

Jan 1, 1975

By F. V. Meriwether

The Bureau of Mines, in cooperation with the Federal, State, and local health services, and the mining companies, and miners? organizations, has for several years been carrying on sanitary surveys of mining districts in various states, with the purpose of collecting information on good and poor practices in mine sanitation, construction of approved wash-houses and change houses, the measures being taken to combat preventable diseases, the essential features of good houses for mining towns, and other conditions affecting the health and efficiency of miners and their families. The knowledge thus gained is disseminated for the common benefit of the mining industry. The sanitary conditions in the coal-mining districts of Alabama, as found by a recent survey made by the writer, are presented in this report. In addition to the towns on which this report is chiefly based, at least twice as many were visited where no details :were taken, but their general conditions are taken into consideration in summing conditions in the coal districts.

Jan 1, 1926