Search Documents

By Louis J. Sousa

In November 1989, the U.S. Bureau of Mines sponsored a 2-day conference to stimulate thinking and discussion about changing materials technologies and implications for the Government's materials information programs. On the first day of the conference, speakers provided overviews of developments occurring in each of the major materials groups. Emerging technological developments, applications, economic and national defense significance, intermaterial competition, and potential market growth in advanced plastics, polymer composites, ceramics, metals, and electronic materials were described. In general, the speakers forecast advanced materials market growth rates in excess of overall gross national product (GNP) though high costs will tend to limit growth outside of aerospace, defense, electronics, medical equipment, and other typically high value-added businesses. On the second day, a wide range of speakers representing several facets of the materials community described how advances in materials technology are creating a need for new types of data, statistics, information, and analysis. Reflecting the speakers' broad range of organizational, professional, and personal perspectives, an array of information needs was identified. Most requirements, however, seemed to fall into one of five major categories: Federal materials research activities, material standards, market and economic information, health and safety, and public policy.

Jan 1, 1990

By Jr. Abel

Subsidence is controlled by a complex combination of mining and geologic factors. For example, a world-wide compilation of data shows that, as the percentage of shale in the overying rock mass decreases and the amount of sandstone increases, the angle of draw (and the area affected by subsidence) decreases. Limestone in the overburden appears to cause as much as a three-fold decrease in the angle of draw compared to a like amount of sandstone. Increased amounts of sandstone were accompanied by a greater surface subsidence relative to the mining height. The total thickness of overburden did not appear to influence the subsidence magnitude above super-critical panels. The greater the thickness extracted the smaller percentage of that thickness that shows up at the surface as subsidence. The greater the percent of the seam extracted, the greater the subsidence reaching the surface. The maximum subsidence above room and pillar panels is dependent on the pillar height and minimum width as well as the other factors listed.

Jan 1, 1980

By R. C. FLEMING

MINING rock asphalt for use as a paving material is an industry which has grown with the spread of the good roads movement. "Mineral Industry During 1930" reports asphaltic pavements constructed, including maintenance and repair but excluding pavement constructed with road-oil, cut-back or emulsified asphalt, as grown from 23 million square yards in 1911 to a high of 144 million in 1927. In 1930 the same source reports 106 million square yards of such paving laid and, in that year, 664,871 tons of native rock asphalt were so utilized. Many states contain rock asphalt deposits of greater or less importance but in only a few places are the de¬posits being mined commercially. In the year cited Ken¬tucky produced 305,024 tons of bituminous sandstone, Texas 270,138 tons, mostly bituminous limestone, while Alabama, Oklahoma, California and Utah produced 89,709 tons of bituminous rock for road construction. In addition Utah produced 37,906 tons of the purer asphaltic products, gilsonite, wurtzilite and ozokerite, for other uses. Speaking generally, the rock asphalt is a sandstone or limestone naturally impregnated with asphalt to an extent that makes it an ideal road surfacing material without mixing or treatment other than crushing. The asphalt content of the commercial product runs 8 to 12 per cent.

Jan 1, 1933

By Peter Grandone

"INTRODUCTION The injection of water into partly depleted-oil-bearing formations as a means of supplying additional energy to flow oil wells now is recognized by the petroleum industry as an effective method of increasing the recovery of oil. The benefits to be derived from water-flooding oil sands were discovered accidentally more than 4o years ago, when oil producers in the Pennsylvania and western New York fields observed suustantial increases, in oil-production rates when water leaked past corroded casings of old wells into producing sands. This observation prompted some operators purposely to perforate or slit the casings opposite the producing formation in some of their wells to permit water to enter the formation. However, as many operators viewed the practice with skepticism and considered it to be in violation of oil-conservation principles,- systematic water-flooding was not initiated until the Pennsylvania legislature, in 1921, enacted a law authorizing water-flooding of oil sands in that State.Although water-flooding has been practiced in a haphazard manner for more than 25 years in Chautauqua and Montgomery Counties, Kansas, planned or systematic water-flooding in that State had its inception in 1935, when the legislature, following the example of Pennsylvania, also passed a lava/ authorizing water-flooding. The early operations and, to some extent, those still, practiced in the Chautauqua-Montgomery area consisted in raising or perforating the casing to allow water from upper strata to gravitate into underlying oil-producing formations. The extent to which this type of water-flooding affected petroleum production in the old stripper area of eastern Kansas is not known, but it is known to have increased oil production ap¬preciably from many leases.Following enactment of the law permitting water-flooding in Kansas, three operators inaugurated, in that same year, three organized flooding projects in three different counties of the southeastern part of the State. The first organized project on record was that of the York State Oil Co. in the Seeley pool, Greenwood County. On this project, the injection was started on May 15, 1935, into the Bartlesville sandstone at a top depth of 1940 feet."

Jul 1, 1944

By E. F. Koppe

The Upper Freeport coal in the Freeport and New Kensington quadrangles, Pennsylvania, varies from a bony streak to a thick coal deposit often exceeding ninety inches, the "Double" or "Thick Freeport". Distinctive basal partings, a central bone layer, and a canneloid top bench may be present. The appearance of a sandstone roof, sandstone rolls, and bony coal at the top of the main coal bench can be anticipated in thin Freeport areas when basal partings are absent. When the two basal partings are present, a shale roof is normal. These effects are correlated with the original topography upon which the coal was deposited. The original depositional high areas tend to coincide with present structural highs. Preliminary data indicate that coal quality, in part, is affected by the deposi-tional setting. In "high" areas, a tendency exists for the main coal bench to contain higher percentages of fusain and mineral matter. Within limits, some-what higher ash fusion temperatures appear to correlate with paleotopographic highs. As a result of these findings, critical examination of the paleotopography and related sediments is indicated in other areas and other coals. The Upper Freeport coal is quite variable both in thickness and composition in the Freeport and New Kensington quadrangles of Pennsylvania (Figure 1). The coal horizon in these quadrangles is marked either by a thin carbonaceous shale bed or by a single bed containing a variable number of partings (binders). The complex coal zone known locally as the "Double" or "Thick Freeport" contains the Upper Freeport Coal Bed at the base; but in addition, it has an overlying bone layer and an upper coal bed occasionally capped with a canneloid layer. The "Thick Freeport" often exceeds 90 inches in thickness, whereas the normal Upper Freeport coal usually varies between 34 and 50 inches.

Jan 1, 1961

Studies were carried out to examine the effect of introducing varying levels of a pisolitic limonite (Yandi) into an Australian iron ore blend. Compared with other ores in the blend Yandi is more porous. This structure is found to have a considerable effect on the sintering behaviour of the blends. Pilot-scale sintering studies and plant trials showed that sinter plant productivity, sinter reducibility and the low-temperature reduction degradation index altered significantly when the level of Yandi in the ore blend exceeded 15 wt%. The improvement in the reducibility is thought to be a direct result of increased porosity in the sinter and the presence of highly reducible pseudo-relict haematite. Plant trials have also shown that operational changes could be made to the sinter plant to avoid potential deterioration of productivity

Dec 1, 1991

By J. Yianatos

The collection zone residence time distribution (RTD) of mechanical self-aerated flotation cells was characterized for liquid and solid per size class (-45 mm, +45-150 mm and +150 mm). It was found that a single large industrial cell with a volume of 130 to 250 m3, now used in plant operations, can be well represented by an LTST (large and small tank-in-series) model plus dead time. From a scale-up point of view, results showed a similar mixing behavior for industrial cells ranging from 130 to 250 m3. Also, single mechanical cells showed a similar mixing pattern (RTD) when compared to large pneumatic flotation columns. It was confirmed that for practical purposes, the mixing condition in a flotation bank of three or more cells in series can be well described by the classical N tanks-in-series model.

Jan 1, 2008

By H. Boghosian

This paper presents the design and construction of a deep basement in a steeply sloping site in glacial till in Glasgow city centre. Existing foundations, adjacent structures and services, in tandem with asymmetric loading, presented particular challenges in the planning, execution and design of the project. The construction methods and temporary works, analysis by the Finite Element method and monitoring carried out are all described.

Jan 1, 2006

By Euclid P. Worden

INTRODUCTION Today, conventional raise boring is an accepted method of development in underground mines and on major construction projects. Over the years that this technique, and its associated machines and tools, have been under development, many articles have been written on the subject. To a great extent, these papers have reported operating results of one or more specific projects or have been generalized reviews of state-of-the-art machines and tools. This paper is intended as a review of the technique from an operational standpoint. Conventional raise boring, as opposed to the related variants box hole drilling and underground blast hole drilling, is a two step process consisting of the pilot hole drilling and reaming cycles. This author has covered the subject of pilot hole drilling in another article (1) . A good review of the current machines and equipment has been presented by Monroe (2) and an overall review of this entire technology was published by E&MJ (3) and Mining Journal, April, 1983 (4) . The subject of the reaming cycle is presented here together with some of the technical aspects of how the drilling tools are intended to be used. OPERATIONS Bit Change After the pilot bit has broken through at the end of the pilot hole cycle, a changeover takes place at both the machine and

Jan 1, 1985

By H. F. Moore

DURING the last six years, there have been many extensive investigations of the fatigue of metals. The major work of 'these investigations has been the determination of constants for fatigue strength of wrought ferrous metals; but during the past year or two there have become available considerable test data on the fatigue strength of certain nonrferrous metals, including copper, brass, bronze, nickel, copper-nickel alloys, aluminum and aluminum alloys, magnesium and magnesium alloys. It is not proposed to give here extensive quantitative tables of test results; for such tables, reference is made to the published data of various laboratories. The following general conclusions, however, seem to be fairly well established: 1. The phenomenon known as "fatigue" of metal really a progressive fracture of metals. A minute (probably submicroscopic) crack is formed in the metal, the internat stress, is intensified at the ends' of the crack, and under successive applications of load the crack spreads like a minute hacksaw cut until there is not enough sound metal left in the cross-section of the piece to stand the load. applied, and then failure occurs suddenly. 2. For wrought ferrous metals, there is .a limiting intensity of stress (as computed by the ordinary formulas of mechanics of materials) below which, a metal is able to withstand an indefinitely large number of repetitions of stress without failure. This limiting stress is known as the "endurance limit or the fatigue limit.? For reversed flexure, the endurance limit for. wrought ferrous metals is usually not far from 50 per cent. of the ultimate tensile strength.

Jan 1, 1925

By Ronald D. Rothchild

This report describes the results of a study of longwall ignition hazards and specific suppression systems to minimize each of the major hazards. The major ignition hazards were identified by conducting a literature search and conversing with knowledgeable individuals in the United States mining industry. Three classes of potential ignition suppression systems are discussed: triggered suppression systems for face ignition, passive suppression systems, and control of ignition hazard in the gob. The triggered suppression systems included protection for the shearer, head and tail gates, welding equipment, and the shearer power cable. Passive systems include improved ventilation and water sprays, and charges in the shearer head. Gob protection can be improved by isolating the gob from working areas and by introducting inerting agents into the gob.

Jan 1, 1976

Early American history is filled with records of the search for and extraction of minerals-a Northwest passage to the treasures of the Indies-an overland route to the goldfields of California. Mining and its associated minerals industry have heralded advancing civilization throughout the ages. The two basic resources on which we all depend for our food, clothing, shelter, and other comforts are agriculture and minerals. Our endowment and how we use it; the spirit and industriousness of our people; our form of social organization all converge to make up our standard of living-our way of life.

Jan 1, 2012

By W. W. Krech, T. E. Perkins

As fractures are propagated through rocks, energy is absorbed near the extending crack tip. Apparent surface energies for several rocks have been measured by cleavage under dynamic con-ditions. At nominal crack velocities from 0.5 to 500 in (min, measurements showed that fractures propagated in discrete jumps. Calculated surface energies and moduli were relatively insensitive to nominal rate of cleavage. in another set of experiments, rocks were cleaved under high confining stresses. The rocks were submerged in low leak-off fluids which formed a filter cake on the freshly cleaved surfaces (similar to the hydraulic lracturing process). Apparent surface energies were increased substantially as the surrounding fluid pressure was increased. Moduli in bending increased significantly upon application of the first 1,000 psi but were insensitive to stress level at greater pressures. INTRODUCTION For almost 20 years, hydraulic fracturing processes have been utilized effectively to stimulate oil and gas wells. During this period, some process improvements have resulted from studies of fracture orientation, mechanics of fracturing, areas generated, conductivities of cracks, etc. Yet many questions remain concerning the conditions and pressures needed during fracture propagation. In this paper we will report additional studies of the mechanics of fracture extension. It was shown previously3 that large rock samples could be cleaved under controlled conditions so as to measure the apparent surface energy (that amount of energy absorbed per unit area of new surface created). In this paper we consider the effects of two additional factors on surface energies, viz.: (1) effect of cleavage rate and (2) effect of confining stress level. THEORY Cleavage experiments were conducted on rock samples similar to that illustrated in Fig. 1. Blocks of rock several inches wide, 2- to 3-in. thick, and up to 3 ft in length were grooved longitudinally with shallow guide slots. A crack was initiated and allowed to extend along the web as the top of the rock specimen was pulled (or pushed) apart. Auxiliary equipment permits the measurement of (1) force applied at the top, (2) separation at the top and (3) crack length. (Further experimental details will be given in the next section.) The rock beams created by the crack are considered ton be cantilever beams. The deflection (or separation of the rock beams) at any point is calculated 4,5 by the beam Eq. 1.

Jan 1, 1967

By Mark Rebagliati, John Payne, Jim Oliver

Abstract-The Campo Morado precious-metal-bearing, volcanogenic massive sulfide deposits occur in a lower Cretaceous, bimodal, calc-alkaline volcanic sequence in a major northerly trending belt in the Guerrero Terrane in northeastern Guerrero, Mexico. During upper Cretaceous to Early Tertiary greenschist-facies regional metamorphism, the rocks were deformed strongly into a northeast-verging fold-and-thrust belt. Three later stages of weak deformation were dominated, respectively, by kink folds, broad warps, and extensional faults. Most deposits occur in the upper part of a sequence of felsic flows and heterolithic volcanoclastic rocks or at its contact with overlying chert and argillite-sandstone. The Reforma and El Rey massive sulfide deposits are on the overturned limb of a major, thrusted anticline, and the Naranjo and El Largo massive sulfide deposits are to the south on the upright limb of the same major fold. The La Lucha and San Rafael massive sulfide occurrences are in an upper plate to the southwest which was thrusted over the plate containing the Naranjo and El Largo deposits. In several of the deposits, Au, Ag, Zn, and Pb are concentrated near the stratigraphic top, and Cu is concentrated near the stratigraphic base. Major minerals are pyrite, quartz, ankerite, sphalerite, chalcopyrite, and galena. Minor minerals are tennantite-freibergite, arsenopyrite, and pyrrhotite. Gold and Ag occur in argentian gold, and Ag also occurs in tennantite-freibergite. The cumulative inferred resource of massive sulfide for the Reforma, Naranjo, El Rey, and El Largo deposits exceeds 30 Mt, with the latter two deposits incompletely delineated. Underlying pyrite-quartz stockwork zones contain chalcopyrite, chlorite, and sphalerite. Hydrothermal alteration minerals in the stratigraphic footwall are pyrite, quartz, chlorite, ferroan dolomite, and ankerite. In the stratigraphic hangingwall, hydrothermal alteration minerals are sericite, calcite-dolomite, and lesser clay minerals and quartz. The deposits belong to a low-sulfidation, volcanogenic massive sulfide system formed in a subaqueous environment, and are of the bimodal, siliciclastic type.

Jan 1, 1997

By Mark Rebagliati, John Payne, Jim Oliver

The Campo Morado precious-metal-bearing, volcanogenic massive sul?de deposits occurin a lower Cretaceous, bimodal, calc-alkaline volcanic sequence in a major northerly trending belt inthe Guerrero Terrane in northeastern Guerrero, Mexico. During upper Cretaceous to Early Tertiary greenschist-facies regional metamorphism, the rocks were deformed strongly into a northeast-verging fold-and-thrust belt. Three later stages of weak deformation were dominated, respectively, by kink folds, broad warps, and extensional faults. Most deposits occur in the upper part of a sequence of felsic ?ows and heterolithic volcanoclastic rocks or at its contact with overlying chert and argillite-sand-stone. The Reforma and El Rey massive sul?de deposits are on the overturned limb of a major, thrusted anticline, and the Naranjo and El Largo massive sul?de deposits are to the south on the upright limb of the same major fold. The La Lucha and San Rafael massive sul?de occurrences are in an upper plate to the southwest which was thrusted over the plate containing the Naranjo and El Largo deposits. In several of the deposits, Au, Ag, Zn, and Pb are concentrated near the stratigraphic top, andCu is concentrated near the stratigraphic base. Major minerals are pyrite, quartz, ankerite, sphalerite,chalcopyrite, and galena. Minor minerals are tennantite-freibergite, arsenopyrite, and pyrrhotite. Goldand Ag occur in argentian gold, and Ag also occurs in tennantite-freibergite. The cumulative inferred resource of massive sul?de for the Reforma, Naranjo, El Rey, and El Largo deposits exceeds 30 Mt, with the latter two deposits incompletely delineated. Underlying pyrite-quartz stockwork zones contain chalcopyrite, chlorite, and sphalerite. Hydrothermal alteration minerals in the stratigraphic foot-wall are pyrite, quartz, chlorite, ferroan dolomite, and ankerite. In the stratigraphic hangingwall, hydrothermal alteration minerals are sericite, calcite-dolomite, and lesser clay minerals and quartz. The deposits belong to a low-sul?dation, volcanogenic massive sul?de system formed in a subaqueous environment, and are of the bimodal, siliciclastic type.

Jan 1, 1997

By R. W. Smith

Living and killed organisms, particularly microorganisms, and extracellular products derived from the organisms are increasingly finding use in minerals engineering. Goals include both enhancement of mineral processing/11.ydrometallurgica,l operations and remediation of mineral industry wastes. Some of the applications, such as biologically assisted leaching of ?sulfide ores and bioxidation of refractory gold ores, are well established commercial ?processes used around the world. Others, such as the use. of organisms for the removal of heavy metal ions from dilute aqueous streams, are nearing commercial application. Many other uses of microorganisms and. their derivatives are potentially possible. These include use of microorganisms in flocculation or flotation of minerals., remediation of organics potentially discharged from mineral engineering operations, degradation of cyanide, the recovery of bitumen from heavy oil reservoirs and tar sands and the solubilisation of lignites and low rank coals. In order to fully exploit these many possible uses of organisms and their derivatives, extensive fundamental .and .applied research work exploring the fundamentals, potential and practicality of the various possible uses of microorganisms in mineral engineering should be vigorously pursued. ?

Jan 1, 1991

By Julien Rivard

Au printemps 2011, la Corporation minière Osisko met en production le gisement Canadian Malartic, qui devient la plus importante mine d?or à ciel ouvert au Canada. Pour lui faire place, elle a déménagé un quartier de 205 maisons et construit 6 nouveaux bâtiments institutionnels. Les démarches ont commencé en 2006. La compagnie a d?abord établi l?emplacement du nouveau quartier résidentiel, en collaboration avec la Ville de Malartic, puis fait la conception de ce quartier de manière à refléter au mieux les caractéristiques du quartier à déménager. Elle a ensuite effectué une opération d?assignation consistant à proposer à chaque propriétaire intéressé un lot dans le nouveau quartier. Au total, 140 résidences ont été déménagées en 2008 et 2009 et 65 été rachetées par la compagnie, le tout par des ententes de gré à gré sauf pour un seul cas. La réussite d?une opération d?une telle importance sociale n?a été possible que parce que la compagnie s?est assurée d?un soutien massif de la population et des autorités pendant tout le processus. Cette expérience peut être fort utile pour les nombreux projets miniers dont l?insertion dans la communauté est un enjeu important.

May 1, 2011

By Kenneth Pidgeon

The Boston Marine Industrial Park (BMIP) Boat Section, which is part of contract C04A2 of the Central Artery/Tunnel (CA/T) project, is currently under construction in South Boston, Massachusetts (Fig. 1). The Boat Section is approximately 900 feet long and varies in width from about 135 to 185 feet (Fig. 2). The depth to the top of the Boat Section base slab varies from about 28 to 31 feet below final ground surface and about 23 to 26 feet below normal ground water levels. The Boat Section is supported on 578 anchors drilled into the underlying bedrock each designed for a working load of 630 kips. Design and Construction Team The owner of the project is the Massachusetts Highway Department (MHD). The owner's representative is the Management Consultant, Bechtel/Parsons Brinckerhoff. The section design consultant (SDC) consisted of HDR Engineering, Inc. with GEI Consultants, Inc. as the geotechnical subconsultant. The general contractor was the joint venture of Kiewit, Perini, Atkinson, and Cashman. The boat anchors were installed by the subcontractor Delta Geotechnical Services, Inc.

Jan 1, 1994

By H Haas

H. HAAS, San Francisco, Cal. (communication to the Secretary?). -Fig. 1 plainly shows that the comparison of the steam-turbine and Diesel-engine plants was made on a basis of 6,000 kw. continuous operating load. The tabulation of costs for an 8,000-kw. load is merely done to show the relation of increased output on' the unit power costs. Both plants would sacrifice their reserve capacity, which is to insure continuous operation, if operated to generate 8,000 kw. continuously; unless Mr. Hawkins advocates the operation of one of the turbines at 33.33 per cent. overload, retaining the other as a standby, which, besides overtaxing the turbine, results in a great loss of efficiency. It would he well for Mr. Hawkins to qualify certain of his statements. Thus, under the caption "Diesel Engines, Selection of Units," he says that "two of the largest Diesel-engine builders take the position that, in the present state of the art, they would not attempt to put out units over 1,000 kw.;" he should qualify it by saving that "two of the largest American Diesel-engine builders take the position that, in the present state of the art in the United States, they would not attempt to put out units over 1,000 kw." The reason that American manufacturers restrict themselves at present to units of that size is to be found not so much in a lack of experience in building large units as in a lack of a sufficient, demand for them in the United States to justify the heavy capital outlay connected with the development of such engines. There are relatively few localities in the United States where fuel prices are as high as they are in the Southwest, and regions of high fuel prices are sparsely settled and have a very limited demand for power. Where low fuel prices obtain, steam turbines are active competitors of Diesel engines for large power plants, particularly when the station load factor is low. As most of the American manufacturers of Diesel engines work under license agreements with European manufacturers, which limit their market to the United States and its possessions and Canada, a further limitation is imposed upon them, leaving to European firms practically the entire world as a market.

Jan 5, 1917

By P. Sarnoff

Gold has always been a crisis investment. For centuries gold has been considered globally the money of last resort. In time of war, inflation, financial uncertainty, political upheaval there has with few exceptions always been a flight to gold. The gold paradox simply is that even though we have gone through for the past handful of years all the kinds of. anxieties that would cause the gold price to rise, it has instead dropped drastically. Figure 1. illustrates the important factors that influenced the gold price significantly up or down before 1987. Obviously, since then, even though we have had wars, inflation, financial problems involving breaking banks and thrifts let alone collapsing financial institutions, the gold price has both in the long-term and the short-term trended downwards. Figure 2. depicts the gold price path since 1987. If the presence of time-honored and time-tested factors that should have driven the gold price up didn't do the job, then logic dictates that new factors to drive the gold price down and keep it depressed arose. And they did. But before addressing these depressants permit me to turn to the arcane art of gold price prediction and fore-casting.

Jan 1, 1992