Search Documents

By Bin Xu, Qian Li, Xin Min, Xiaoliang Liu, Yongbin Yang, Tao Jiang, Yan Zhang

The ringing characteristics of acid and alkaline iron ore pellets powder in kiln were studied by the thermodynamic calculation using software FactSage7.0, roasting experiments using briquetting method and analysis of SEM-EDS. The thermodynamic calculation demonstrated that liquid phase could be generated from alkaline pellets powder at a lower temperature and the amount of formed liquid phase was much more than that from acid pellets powder at the same temperature. Roasting experiments indicated that the compression strength of alkaline pellets powder briquettes were also higher than that of acid pellets powder briquettes. Additionally, the analysis of SEM-EDS suggested that the alkaline pellets powder briquette presented more liquid phase and a more compact structure comparing with the acid pellets powder briquette, which was consistent with the results of thermodynamic calculation and roasting experiments. Hence, in comparison with acid pellets powder, alkaline pellets powder is much easier to ring in the kiln.

Mar 1, 2017

Fluid circulation occurs in oceanic crust of all ages, at the seafloor spreading axis, on mid-ocean ridge flanks, in the ocean basins, and in subduction zones. In the first three settings the fluid originates as seawater. At the axis and on the ridge flanks, the circulating seawater produces a major chemical exchange between the oceans and the crust. Based on heat budget constraints, between 10 and 40% of the river flux of Mg can be taken up during high-temperature alteration of the basaltic crust along the mid-ocean ridge axis. Most of the hydrothermal -heat loss, however, occurs on the mid-ocean ridge flanks, where the temperatures are lower and the seawater flux correspondingly larger. The estimated heat loss on the flanks is so large that upwelling must occur over a large fraction (5-30%) of the seafloor less than 65 Ma in age, at seepage velocities on the order of 10 to 100 cm/yr. The circulating seawater need lose less than 1 to 2% of its Mg content in order to solve the Mg mass balance for the oceans. Fluids in subduction zones are commonly less saline than seawater and are rich in methane and other light hydrocarbons. These fluids may originate by dewatering of the downgoing slab. If so, they may close the geochemical cycle of H2O that began with hydration of the basaltic crust at the ridge axis.

Jan 1, 1990

During the 1950's there was a flurry of activity on the design of main ventilation shafts for mines. More recently, a new ana- lysis was commissioned in relation to the multi-shaft, nuclear waste isolation facili- ties currently under design in the United States. This paper presents the major find- ings of that study and should prove of value as a reference in the design of proposed new shafts. An overview of mine shaft resistance introduces the effects of the shaft walls, fittings, conveyances and shaft stations. Each of these is analyzed in turn. A com- pletely new technique is described, which facilitates the estimation of wall resis- tance. The effect of size of a conveyance is quantified and shown to be dominant when the cage occupies more than 30 per cent of the shaft cross-section. The dynamic effects of a moving conveyance are also analyzed.

Jan 1, 1988

By Arthur S. Huey

AS the end of the collegiate year approaches, the problem of student employment again becomes acute. This subject divides itself into two phases: (1) employment prior to graduation and (2) employment following graduation. "Experience is the best teacher," according to the old adage, and the student needs all that he can get. He is afforded every opportunity to reap from his books the theories and principles of scientific and engineering practice, and occasionally he is privileged to make field trips to observe the practical side of the subject. But it is not enough for one to know the theory and to observe its application; it is also desirable for the student to get the feel of the tools during his training Such opportunities can only be afforded the student if the major companies cooperate with the universities in giving the student part-time and vacation work.

Jan 1, 1932

By E. D. Peters

It frequently occurs in the establishment of reduction works, in an entirely new and untried mining district, that the metallurgist in charge finds considerable difficulty in determining the process best adapted to the ores which he receives for treatment. At the first glance it would seem easy enough to decide what style of furnace is best adapted for beneficiating any one class of minerals. If the ore possessed a quartzose gangue and was comparatively free from base metals, while salt could be obtained at a reasonable price, one would naturally resort to a chloridizing roasting, and pan or barrel amalgamation for the extraction of its silver contents. If galena or carbonate of lead was the prevailing mineral, and charcoal could be obtained at moderate figures, the blast-furnace would beneficiate the ores most advantageously. But if, as is usually the case in Colorado, the ores consisted of an intimate mixture of galena, zinc-blende, copper-pyrites, and noble silver minerals, associated with an overwhelming mass of siliceous heavy spar, or limestone gangue, the common reverberatory furnace can be used to the greatest advantage ; and, although the product is only a copper matte, I do not hesitate to affirm that it can be treated, and the silver, gold, and copper produced at nearly the same price for which silver and lead can be separated. In Germany, blast-furnaces are frequently used for this same purpose, both for argentiferous and non-argeutiferous copper ores; but any one who will take the trouble to examine the statistics of smelting at Fahlun, the Oberharz, and other Continental works of this description, will see that the expenses are far too great, and the production much too small to think of employing this method in our mining districts, where only the softest and most miserable kind of charcoal is obtainable. I propose in this paper to give an accurate account of the expenses incurred at the Mount Lincoln Smelting Works in treating the same kind of ore, and producing the same end-product in both blast and reverberatory furnaces. I have taken for comparison a favorable campaign of the blast-furnace, and a good average month's running of the reverberatory. In the blast-furnace estimate I have included the calcining and concentration of the matte produced during that campaign, as I always, when possible, concentrated the regulus made

By S Wilkinson, S Black, L van den Berg

"The mine ventilation system plays an important role in mitigating human exposure to diesel particulate emissions (DPM), exhaust gases and heat in underground mines. The mine’s secondary ventilation systems are critical for diluting contaminants when working at the face of a heading. To improve these systems it is important to understand and visualise the localised air flow profiles. We have considered an approach that includes both tracer gas measurement–modelling to analyse this complex flow behaviour in a heading. The use of tracer gas enables reliable measurements of flow behaviour and differentiation between the contributions of various contaminant sources including DPM. A pilot study was conducted to demonstrate how tracer gas can be used to directly measure the effectiveness of ventilation dilution in a heading during shotcrete activity. This activity is considered to be one of the more challenging areas for diesel exhaust exposure management. Exposure sources include the diesel engine of the spraying equipment (Spraymech) and concrete agitator truck (Agi) that supplies the shotcrete. During operation both the Spraymech and Agi operators are located outside the equipment’s air-conditioned cabins and both are exposed to diesel exhaust. In the pilot study tracer gas was injected directly into the Spraymech exhaust stream. This allowed thorough mixing, ensuring the tracer gas was able to track exhaust gases and particulates released to the heading. The release was repeated at three different headings with varying degrees of secondary ventilation controls. The study showed that small changes to the secondary ventilation system can significantly impact the contaminant concentration. It also demonstrated that tracer gas can be used to isolate different contaminant sources. The intent is to use this technique in a more comprehensive study to develop best practice guidelines for secondary ventilation installations. This paper presents the technique used and the preliminary results from the pilot study. CITATION: Wilkinson, S, van den Berg, L and Black, S, 2015. Application of tracer gas flow profiling to improve secondary ventilation practice – a pilot study, in Proceedings The Australian Mine Ventilation Conference, pp 345–352 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 31, 2015

By H. J. Hager, B. W. Gandrud, G. D. Coe

"INTRODUCTION The reduction of washery losses of marketable coal is a phase of coal preparation important to many of the Alabama coal producers. The problem has wide scope, and this report deals with but one of its several aspects. The investigation on which this report is based was made by the Southern Experiment Station of the Bureau of Mines with the cooperation of the Alabama By-products Corporation and the University of Alabama. The Alabama Byproducts Corporation provided samples of table middlings from its Colta washery on the Mary Lee bed at Flat Creek, Ala.PRACTICE AT THE COLTA WASHYAt Colta run-of-mine coal is crushed in a hammer mill in closed circuit with 5/16-inch square-mesh vibrating screens and tabled without classification on eight rectangular-deck wet tables. The coal is more friable than the bone normally present, and hence the bone is concentrated in the coarser sizes. An unclassified feed of this character can not be tabled with high efficiency to low ash content because of the sizing action of a concentrating table, which is such that when the tables are adjusted to exclude the coarse bone from the washed coal, a large amount of fine coal is lost in the middlings. At the time this investigation was undertaken there was no market outlet for middlings, with the result that middling products had to be discarded with the refuse."

May 1, 1939

By Paul M. C. B. M. Cools, Martin Th. van Staveren

In 2010, the 5-years joint industry programme Geo-Impuls started in the Netherlands. The ambitious goal of this programme is to reduce geotechnical failures in our civil engineering projects by half in 2015. In the Geo-Impuls programme over 40 client organizations, engineering firms, contractors, research institutes, and universities are involved. In a risk-driven way, and based on top risks and dilemmas, the participants defined three central development themes. These themes are (1) contracts, for dealing with legal issues, (2) geo-engineering, for dealing with technical issues, and (3) communication, for paying attention to differences in risk perception by the human factor. In total 12 Working Groups contribute to these themes by producing one or more specific tools. These provide practical solutions for how to deal with contractual, geotechnical, and communication issues. The tools include working processes, guidelines, best practices, as well as some instruments. The development of these tools, as well as the available results, will be presented in this paper. From the start, Geo-Impuls embraced geotechnical risk management (GeoRM) as the risk-driven way of working for geotechnical engineering and construction. Over the past years, GeoRM and its supporting tools were already successfully applied in several projects. Therefore, the paper also describes also the GeoRM implementation process, including the quality assurance and control. Finally, the effectiveness of GeoRM will be discussed, by summarizing an analysis of all published geotechnical failures and accidents in construction projects in the Netherlands, which decreased substantially over the past 4 years.

Jan 1, 2017

By S. Nakamura, M. Takaoka, Y. Mizuno, T. Kusakabe

"Mercury is produced as a byproduct from gold mines and, historically, has been transferred to recyclers and used for various industrial processes and products. However, under the Minamata Convention on Mercury, adopted in 2013,the intentional use of mercury in processes or products will be minimized in the world. Surplus elemental mercury should be treated as a hazardous waste and consequently, should be converted to a more stable chemical form for long-term storage or permanent disposal. A stabilization method has been developed to react mercury and sulfur using a planetary ball mill. The planetary ball mill can produce high-energy conditions and enable samples to react within a short period of time. A series of tests has been conducted to confirm that mercury sulfide can be produced using a bench scale machine with 2400 mL pot. Under a suitable experimental condition with 25 mm ball diameter, 30%of ball filling rate and 1.05 of molar ratio of S/Hg, a powdered mercury sulfide product was successfully obtained in 60 minutes. The leach ability and atmospheric emission from the product was extremely low. This stabilization method would contribute to an environmentally sound mercury management strategy for the gold industry.INTRODUCTIONDue to its unique physical and chemical properties, mercury has numerous applications, including in industry and medicine. However, mercury and its compounds are highly toxic. For example, in Japan, methyl mercury in waste water caused Minamata disease in the 1950s, which affected large numbers of people (Minamata Disease Municipal Museum, 2001). In recent years, environmental pollution caused by emissions and releases of mercury into the atmosphere, waterbody and land by various emission sources such as coal fire plants, artisanal and small-scale gold mining (ASGM), non-ferrous metal industries, waste incinerations etc. has also become a significant problem. To protect human health and the environment from anthropogenic emissions and releases of mercury and its compounds, the Minamata Convention on Mercury was adopted in 2013(UNEP, 2013)Because ground gold ore typically contains mercury at 0 to 100 ppm, mercury is often produced as a byproduct from gold mines (UNEP, 2016). In gold mining operations, mercury can be released from the ore by roasting or by leaching in cyanide solutions and recovery onto activated carbon. According to Yanget al. (2016), 85.1%of mercury in a concentrate was vaporized during a roasting process. Both processes finally discharge elemental mercury as a byproduct. In the USA, more than 100 ton of mercury was discharged from large-scale and industrial gold mining (Miller, 2004)."

Jan 1, 2017

By R. B. STEWART

A few days ago, while reading a report of the late Dr. Robert Bell in preparation for this afternoon's meeting, I found some impressive figures concerning the magnitude of the Hudson Bay basin. From the waters of the Bay itself, this great territory extends eastward 500 miles, westward l,300 miles to the Rocky mountains, and southward to the source of the Red river. It has a width of 2,100 miles from east to west, and a length of l,500 miles from north to south. Its area is almost three million square miles. It is not, of course, my intention to review the natural resources of this vast territory, but to confine my remarks to that portion of it adjacent to the waters of Hudson bay. A number of erroneous ideas exist in the minds of many concerning this northern country, especially as regards its latitude and climate. Burwell, at the entrance of Hudson strait, is in the latitude of 60 degrees or roughly that of the north of Scotland. The southern end of James bay has about the same latitude as the northern end of Vancouver .island.

Jan 1, 1928

By D Reid

Characterisation of non-plastic segregating tailings presents a number of challenges: the material cannot typically be sampled in an undisturbed state, remoulded samples exhibit different behaviour to undisturbed samples, penetration test interpretation methods suffer from uncertainty in their application to many tailings and the tailings gradation changes considerably over relatively small lateral distances and depth. In addition, the process liquor of many Western Australian tailings contains large quantities of salt and other dissolved solids, which can further complicate laboratory test programs. To provide an insight into the variability at a typical gold tailings facility, four gradations of the material were tested to obtain critical state parameters. Historic surficial tube samples were collated and organised by gradation to establish the range of densities typical after settling and air drying. These were then compared to laboratory-accessible densities. Finally, tube samples were tested in the laboratory to observe if the large-strain material behaviour was consistent with the inferred critical state parameters for similar gradations. Site pore fluid was used in the testing of the tube samples in an attempt to assess if the pore fluid modified the critical state conditions of the material.The tube samples tested all exhibited strongly dilative behaviour in undrained shear. Of the four samples tested, only one exhibited behaviour consistent with the inferred location of the critical state line relevant to the material’s gradation. The reasons for the unexpected behaviour of the other three samples include layering within the samples, the potential influence of large quantities of salt in the pore fluid and likely differences in the gradation of the fines components of samples taken from mid-beach and the decant area.CITATION:Reid, D, 2015. Observations on the behaviour of a gold tailings with hypersaline pore fluid, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 191–200 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By John H. Schloen

Copper refineries are constantly looking for methods to upgrade their plants to reduce refining costs and to improve the purity of their electrolytic cathodes at the same time that the purity of the anodes they refine is being lowered by the rehabilitation of reverberatory furnace smelters to one of the direct smelting processes. The comments given below are based on the answers to the questionnaire returned bf the 36 copper refineries that represent 66% of the western world s refining capacity. Eleven refineries employ some form of uniform weight anade casting, e.g., Outokumpu, Contilanode, Mitsubishi, Lurgi, or Hazelett. This type of anode casting presents the best possibility for improving cathode purity. The cathode press of Phelps Dadge can improve current efficiencies and cathode quality. The press is used on first-run cathodes, after 48-60 hours, on half-cells at a time without interruption of the cell current. One refinery interrupts current for sever.al hours to allow the anode slime to settle before the, cathode pressing. The cathode press is now used at eight refineries. Apart from periodic reverse current (PRC), it is not expected that current densities will be increased. Thirty refineries, using direct current, average 231 amps/M, with a low of 178 and a high of 350. Five refineries use PRC at an average of 338 amps/M, with a low of 290 and a high of 380. Current efficiencies are good at an average of 94%, with a low of 88% and a high of 99% for the 34 refineries that reported. It must be remembered that the cycle efficiency with PRC is about 93%., so that the effective current efficiency with PRC would be only .94 X .93 or 87% However, PRC should be considered seriously for refinery expansions because it can save about 25% on capital costs.

Jan 1, 1987

By Resta S. A

Energy Resources of Australia Ltd - Ranger Mine is located about 255 kilometres east of Darwin in the Alligator Rivers Region of the Northern Territory. The Ranger project is surrounded by Kakadu National Park which is on the UNESCO World Heritage list. . Ranger Mine operates the largest uranium mine and processing plant in Australia. It is designed to produce 3000 tonnes of uranium oxide per year, but presently is producing a little less than one half that figure due to the depressed uranium market. The safety performance of the employees and Ranger as a whole continues to improve. The lost time injuries (LTI) have significantly reduced from 74 in 1985 to five in 1994. The total days lost due to LTIs have gone from 1543 to 14. These significant improvements have reflected directly on workers' compensation premiums in which a four-fold reduction has occurred. It is estimated that the actual monetary saving to the company is about $1.3 million per year and directly reports to the profit of the company. There is also an obvious and significant reduction in the less quantifiable costs such as the suffering of the injured employees and cost to society. The paper will review the various initiatives introduced and assess their effectiveness. Performance improvement is primarily dependent on the commitment, introduction of various initiatives and the subsequent change in workplace culture.

Jan 1, 1994

The Technology Transfer Seminar on Mine Communications held on March 21-77, 1973, at the Pittsburgh Mining and Safety Research Center, Bruceton, Pa., presented information about recently developed equipment, instruments, and techniques for use in mine communications systems. All of the basic ideas presented in the fine seminar are operational in the Bureau of Mines Safety Research Mine in Bruceton.

Jan 1, 1974

By Weller KR

A study of high pressure rolls grinding of a number of Australian ores and minerals has been carried out using a pilot-scale machine with rolls 300 mm diameter and 70 mm wide. The results from this study have been used in conjunction with plant survey data to construct computer simulation models of various comminution circuits and these have been used to investigate options for incorporating high pressure grinding rolls into these comminution circuits. Possible rolls options for three of these circuits are presented, and likely energy savings over the existing circuits are discussed together with potential improvements in plant throughput and/or product sizing. A scale-up procedure for predicting full-scale machine performance from small-scale testing is described, and the effects of rolls operating conditions are also discussed.

Jan 1, 1991

By D J. Kilkenny

Work practices involved in shaft construction can be aligned with current industry standard operating practices. However, the working environment during conventional shaft construction introduces unique conditions which can not always be overcome by hard engineering controls. To provide an improved working environment, future shaft diameters will generally be greater than has historically been the case for the Australian hard rock mining industry. This paper aims to explore both what can be constructed from the contractors perspective, and how does an owner extract maximum business efficiency from an asset that in many ways is likely to be larger, more complex and more expensive than initially envisaged.Newcrest Mining Limited, or an associated company, has constructed two major shafts over the last seven years. In both cases, Byrnecut Mining, or an associated company, was the contractor engaged for the shaft sinking activity. The first is the 1127 m deep, 7.0 m diameter production and intake airway at the Telfer Gold Mine, the second is a 295 m deep, 5.5 m diameter split shaft at the Gosowong Gold Project in Indonesia that was primarily designed as both an intake and exhaust airway. Importantly both shafts are designed to provide emergency egress from the respective underground operations.From an Australian shaft sinking perspective, the construction of these two shafts resulted in the following learnings: •constructability is of equal importance to desired functionality;•allow six months of interactive design between the owner/engineer/contractor/regulator to get it right;•shaft sinking and equipping are intimately entwined, therefore engineering of both needs to be complete prior to any activity commencing; and•the mobilisation of both equipment and experienced personnel to a new shaft sink takes up to eight months.Shaft sinking is not extinct in the Australian hard rock mining industry. But, if you are considering constructing a shaft, approach it as a long life asset, front end planning to a high level of detail is required to unlock its full value. Think – plan – think and remember it’s going to take 12 months to get from the whiteboard to firing the first cut.

Mar 21, 2011

By Rodrigo Cesar de Miranda

A importância de descrever o processo de beneficiamento por um modelo matemático tem sido apresentada por vários pesquisadores. O principal benefício é o controle e a otimização do processo dentro de uma situação industrial. O modelo seria capaz de prever determinada variável de controle do processo a partir de dados conhecidos. Assim, a simulação dinâmica representa um marco no campo da otimização de processos minerais. Essa tecnologia de simulação tem uma ampla aplicação no estudo de processos, o que permite a obtenção do seu conhecimento e domínio operacional. Além disso, possibilita melhores definições nas etapas de projeto, além de realizar uma análise de confiabilidade mais realista. O presente trabalho consiste em realizar uma análise de confiabilidade, através da simulação dinâmica, para entender como as paradas não-programadas influenciam a produção de uma planta de beneficiamento de ferro. Ainda, visa entender o desempenho fenomenológico dos equipamentos de acordo com a entrada de diferentes tipos de minérios e também como são suscetíveis a condições climáticas.

Aug 17, 2017

By Wymer DG

The concept of hydro power in deep mines is based on the exploitation of the hydrostatic head that can be gained as refrigerated cooling water descends in shaft pipe columns from the surface, to provide hydraulic power for machines at the working face. This paper describes the work done on two important aspects of the controlled distribu-tion of the high pressure water within a mine, namely the control of pressure under normal operating conditions, and the control of flow in an emergency situation following a pipe breakage. Suitable methods of control have been determined using theoretical techniques to model the steady and unsteady flow behaviour of the water in the pipeline, and taking into consideration the environmental constraints on the types of control devices that can be used. The preferred approach is one in which the high pressure water itself is used as the control medium. The control valves themselves can be fairly conventional in design, but in the case of pipe break protection it is shown that a less conventional approach based on the use of a hydraulic fuse gives improved control performance.

Jan 1, 1985

By S. S. Clarke

ABOUT two years ago some of my friends were discussing the amount of drill-steel breakage that was permissible or not excessive, per month, per rock ton, per ton of steel or any unit of measure or output that would give a comparison between different kinds of drill steel. No one seemed to know what life to expect of steel, or what percentage of breakage might be termed excessive. In fact there were no operating data available to guide one in selecting the best steel for our mines, nor could any ideas or information be secured from the steel manufacturers. One was merely told that so and so used their steel and it was very satisfactory; or else one was given a highly technical lecture on their specific heat-treatment. Any estimates on expected breakage were just guesses, ranging from a fraction of a per cent to as high as ten per cent per month.

Jan 1, 1933

By Karen Leão dos Santos

A borracha sintética (SBR) é amplamente utilizada em indústrias de pneus combinada a cargas de reforço para melhoria das propriedades do elastômero puro. Atualmente, as cargas que apresentam melhor capacidade de reforço em elastômeros são a sílica e o negro de fumo. O presente estudo buscou avaliar o desempenho de compostos de borracha sobre as características de resistência ao rolamento, tração em piso molhado e resistência à abrasão, em função das quantidades de sílica e de negro de fumo. Foram realizados ensaios mecânicos e dinâmico-mecânicos, e, a partir dos resultados obtidos, concluiu-se que a utilização das diferentes cargas de reforço no composto de borracha está associada ao tipo de uso a que se destina o pneu.

Aug 17, 2017