Search Documents

By Artur Camposo Pereira

O presente trabalho buscou explorar a aplicação da ultramicrodureza instrumentada na caracterização microestrutural e mecânica de materiais metálicos aço inoxidável 304L e liga NiTi Rica em Ni, ambos no campo austenítico. Para isso foi utilizado um ultramicrodurômetro instrumentado (Shimadzu, modelo DUH–211S) com medidas a temperatura ambiente e distintas cargas máximas e tempos de permanência. De acordo com algumas das possibilidades apresentadas, pode-se concluir que a ultramicrodureza instrumentada é uma ferramenta poderosa para a caracterização mecânica correlacionada aos aspectos microestruturais de materiais metálicos.

Aug 17, 2017

By G. R. Hopkins

A fifth successive record in fuel efficiency was established by the petroleum-refining industry in 1937, when the average heat requirement per barrel of crude oil run to stills was 554,000 3. t. u. compared with 597,000 3. t. u. in 1936. These amounts represent roughly the heat ob¬tainable from a tenth of a barrel of fuel oil (see fig. 1). Innumerable factors can influence heat consumption at rep aeries, but only a few are important enough to be subject to statistical measurement. Foremost of these is the ratio of runs to capacity, it being generally recognized that because the fuel demands for other than stills are comparatively inelastic, total heat requirements do not increase in direct proportion to crude runs. Thus, in 1937, crude runs of 1,183,440,000 barrels wore 11 percent higher than in 1930; the average operating ratio was 93 percent compared with 79 percent in 1936; but the total heat requirement increased only 4 percent, or from 639,149 billion 3. t. u. in 1936 to 663,966 billion 3. t. u. in 1937.

Jan 1, 1938

By Cesimiro Fabian

The crystallite size of copper electrodeposits was determined by X-Ray powder diffraction analysis using a General Area Detector Diffraction Solution (GADDS) diffractometer. Crystallite size was calculated for copper thin films which were deposited on a 316 stainless steel rotating cylinder electrode (RCE) in the presence and absence of additive ?A?. The crystallite size was calculated from a corrected full width at half maximum (FWHM) of the [110] peak profile using the Scherrer equation. The test of significant difference on crystallite size was derived using Kruskal-Wallis method. It was found that in the absence of the additive the median crystallite size was 426, which decreased to 364 in the presence of the additive. As the additive degraded, the crystallite size increased to a size similar to that observed in the absence of additive.

Jan 1, 2003

By Elisa Araujo Santos Darsie

A busca na melhoria da qualidade dos aços, principalmente no caso de aços limpos, fez com que o distribuidor de lingotamento continuo também seja empregado para a remoção das inclusões responsáveis por prejudicar as propriedades mecânicas dos aços. Uma melhor eficiência desta função do distribuidor pode ser atingida com o conhecimento das características do escoamento do banho metálico de modo que se possam propor modificações na configuração do distribuidor. Esses fenômenos de escoamento e remoção de inclusões podem ser simulados mediante a utilização da modelagem física. O objetivo deste trabalho é avaliar quatro configurações internas de distribuidor por meio da qualificação do escoamento via ensaio de linhas de fluxo e quantificação de inclusões passantes pelo veio com o ensaio de remoção de inclusões. As variáveis de controle utilizadas neste estudo são: velocidade de lingotamento, presença de barreiras e presença de tubo longo. Os resultados apresentados para o distribuidor em questão mostram que para os casos com o tubo longo, o uso da barreira torna o escoamento predominantemente ascendente eliminando o curto-circuito e favorável a remoção de inclusões passando de 29,76 para 24,29% de inclusões passantes pelo veio. Enquanto que para os casos sem tubo longo, o uso da barreira proposta diminuiu o contato do aço com a escória sobrenadante, aumentou o curto-circuito e aumentou também o percentual de inclusões passantes pelo veio de 2,56 para 3,01%.

Aug 8, 2018

By Félix Lewandowsky

El presente texto describe las actividades para corregir los pasivos ambientales heredados y asumidos bajo responsabilidad de la Compañía Minera Colquirrumi S.A. Para ello, se elaboró un plan de cierre de los cuatro depósitos de los relaves de Hualgayoc donde se busca mostrar los criterios utilizados, los estudios de ingeniería y la forma cómo se ejecutaron las obras de cierre definitivas de los depósitos de relaves.

Jan 1, 2015

By Huntington J. F, Green A. A

The quality of a photointerpreter's anno- tation of an image may be displayed by writing maps in which the pixels are shaded according to the number of times a pixel was seen to be on a feature. The map of grey tones is more valuable, if, for each grey level, a measure of quality is determined, which is the probability that a feature exists in a pixel of a given grey tone. From repeated annotations (at least four) of the same image by a single observer, it is possible to formulate a perception model which describes stochastic processes in the observer. From that model, it is possible to assign estimates of data quality for each observer to each grey tone. For two observers on the same scene, the 'mean' method of quantifying the grey levels is to assign a value equal to the mean of the ii,:lities for each of the two observers separately. For this example, the grey tones arr thus quantified at probability levels of 0.70, 0.80, 0.90 and 0.95.

Jan 1, 1977

(The following list contains the names of those members of the Institute of whose connection with military service we have only recently become acquainted; it also includes the names of a few who have recently been promoted or transferred, indicated by a *. A complete list was published in the Year Book, issued as a supplement of the Bulletin for March, 1918.) *AMBLER, HARRY A., 1st Lieutenant, 0. R. C., 30th Infantry, A. E. F. BAKER, R. F., Private, Intelligence Section, Headquarters 90th Division. *BARTON, L. A., Captain, 604th Engineers. *BATTEN, H. L., Lieutenant, Canadian Engineers, C. E. F. *BENSEL, J. A., Major, U. S. Reserves. BIRKETT, HOWARD, Lieutenant, Aviation, U. S. Signal Corps. BLOOMFIELD, E. C., Lieutenant, 1st Canadian Tunnelling Co. BOOTH, L. E., Watertown Arsenal, Det. E. 0. C., N. A., Watertown, Mass. *BOWMAN, REGINALD G., 1st Lieutenant, Engineers, U. S. R., Int. Ord. Dept. No. 4, A. E. F. *BRADLEY, CLARENCE I., Convois Automobile Section 585,. S. S. U., P. A. R., B. C. M.

Jan 7, 1918

By J. Kalejta

Ever increasing depth of mineral extraction presents a challenging environment for hard rock underground mines. High in-situ stresses and associated seismicity with potential rockburst hazards are the major decisive factors contributing to the choice of a ground support regime. Conventional ground support systems, designed primarily for static loads, are not always capable of providing safe working conditions for underground personnel in seismically active mines. Systems specifically developed to resist dynamic loading and allowing for larger deformations are therefore preferred alternatives. High-tensile chain-link mesh has a proven record of successful use in open cut operations in various rockfall barrier installations due to its high energy absorption capacity. It has also been used in underground operations in various parts of the world. This paper describes a method of mechanized installation of a chain-link mesh evaluated at the Kiruna mine in Sweden and South Deep Mine in South Africa. A purpose-built mechanized roll mesh handler was used in this evaluation. The handler is compatible with all standard multi-boom underground drill rigs and is operated utilizing the hydraulic circuit normally used for the feed arrangement. A number of key performance indicators have been identified as success criteria: ??A 30-50% faster installation compared to the conventional methodology ??The mesh should sustain any blast damage when applied to the blasting face ??No unraveling of the mesh when cut ??No failure of mesh under normal conditions Although the energy-absorbing mesh combined with yielding rock bolts is a ground support system of choice for rockburst prone conditions, the operational upsides recognized during the evaluation imply that this product can also be competitively used in less demanding ground conditions where customarily weld mesh or shotcrete are used as a primary surface support. The main conclusion: a fast, safe and fully mechanized installation.

Aug 1, 2013

By Guilherme Vieira Braga Lemos

Uma superliga a base de Níquel, popularmente conhecida como Inconel 625®, foi estudada no presente trabalho. A Soldagem por Fricção e Mistura Mecânica (SFMM) aplicada a liga 625 foi realizada com velocidades de rotação da ferramenta entre 1200 a 200 rpm e velocidade de soldagem entre 1 e 1,5mm/s. O aporte térmico foi calculado como função dos parâmetros de soldagem empregados. Adicionalmente, análises metalográficas e de microdureza foram realizadas na seção transversal das juntas soldadas. A aplicação da soldagem no estado sólido foi efetiva e resultou em maiores valores de microdureza todas as juntas soldadas. Por outro lado, um aumento na velocidade de rotação causou um aumento do aporte térmico.

Aug 17, 2017

Blast Engineers frequently use the terminology "the blast showed good heave", or even "the heave was better this time". It is reasonably obvious that "good" and "better" are not the best terms to use. It is also noted that any variation in the data can be misleading. The author proposes a more precisely defined and objective set of measures as tried and tested in a project in 1988. Simple objective measurements of a muck pile profile can measure 1. distance thrown 2. spread of material 3. heaping of material 4. skewness, or bias in the heaping 5. rotation of the mass This technique enables one to compare the profiles from different blasts without relying on subjective experience or judgement. Simple, artificial profiles will be presented to illustrate the problems of description; and then application of the measurement techniques to these profies will be discussed with physical interpretations. The mathematical techniques will be presented, and results of the application of the techniques to real data collected during research carried out at Baimsdale in Victoria, will be presented as illustration. The use of these techniques in mathematical modelling will be discussed.

Jan 1, 1990

A field trial of the prompt neutron-gamma SIROLOG technique was undertaken by the CSIRO - Division of Geomechanics at Callide Coalfields during July 1989. The trial investigated whether the sonde could reliably be used for the determination of Ash and Iron Oxide (Fe2O3) in coal seams, which had a highly variable iron content. Ten boreholes were logged, being water filled of a nominal diameter of 120 mm. The logging probe employed a 1.6 ¦g 252Cf neutron source and a 51 x 51 mm BGO detector. The source to detector distance was 15 cm. The results from one exploration borehole at the Dunn Creek Mine are discussed in the paper. The rms deviations for ash and iron determination between the neutron-capture predictions of the geophysical logs and the laboratory - chemical assays were 1.9 per cent Ash and 0.88 per cent Fe respectively. Using existing empirical equations which relate iron oxide concentration in coal ash to Initial Deformation Temperature (reducing conditions) at Callide, it may be possible to indirectly determine ash fusion properties as least as accurately, on a more detailed ply-by-ply basis, and more cost competitively than current laboratory techniques allow.

Jan 1, 1991

By Fabiano Mendes

Processos industriais de carbonização são tecnologias maduras e operam há mais de 7 décadas. Contudo, o sistema integrado de produção de ferro primário e aços a base de biomassa como fonte de energia e termorredutor, mesmo sendo a alternativa ambiental de menor impacto existente, chega a seus limites tecnológicos, ambiental e econômico, ameaçando a sua sustentabilidade. O grupo Vallourec buscou o processo Lambiotte como base tecnológica para desenvolver seu ambicioso projeto de carbonização contínua, em substituição ao processo artesanal de fornos retangulares de batelada, utilizados atualmente. O esforço experimental de mais de meia década, com a adaptação e profunda reengenharia do processo Lambiotte, que é o que melhor representa esta classe de reatores, para que ele atendesse as condições brasileiras e o uso das espécies de madeira da família dos Eucaliptos culminou no desenvolvimento do processo de carbonização continua Carboval, que demonstrou sua plena capacidade, para atender aspectos econômicos, sustentáveis e de qualidade siderúrgica do carvão vegetal produzido.

Aug 17, 2017

By M. Jaramillo

The Expanded West Pit of the 15 MTY El Cerrejon Mine will reach a maximum depth of270 m. Slope stability evaluations indicated that this depth, combined with structural complexities, would create a serious risk of footwall instability. Stabilization call for anchoring the footwall by installation of cable bolts, 9 to 33 m long, of multi-strand steel cable. For each of the 15 m high mining benches, a row of bolts is installed with variable horizontal spacing, depending on dip magnitude. Cable bolting is now standard operating practice and 11800 bolts will have been installed during the life of the mine.

Jan 1, 1995

By H. P. Greenwald

About mid-December 1936, the safety director of a large coal corporation visited the authors at the Bureau's Experimental coal mine to discuss a rock-dust barrier he had invented primarily for use in trackless entries of coal mines. The rock dust in this device was carried in its original paper containers and means were provided for ripping these open so that the dust might be scattered in the path of an explosion. The inventor termed the device a "bag barrier", and this term has been adopted in the present paper for convenience. At that time the device was in an early stage of development, and the inventor felt that the barrier should be tested to determine whether it had enough promise of being successful to justify further development. The matter was taken under consideration and finally three tests were made during the week of February 15, 1937. It was concluded that while the device did stop an explosion in two of the three tests, it was much loss effective than ordinary rock dusting, and that too few data were obtained to permit direct comparison with tests of other barriers. Apparently, the conditions under which the device could, be successful were somewhat limited, out the limits could not be defined without additional tests.

Jan 1, 1938

By R. ?. Shishmarjov, Yu. ?. Davidenko, S. V. Bukhalov, ?. S. Baksheev, M. S. Shkirya, N. ?. Aikasheva, D. V. Bogdanovich, ?. Yu. Faustova

"The goal of prospecting operations in the Republic of Altay was to locate gold-sulfide-quartz mineralization. For this purpose we applied the technology of electromagnetic sounding and induced polarization (EMS-IP). These operations resulted in localizing promising sites with presence of sulfidization. The EMS-IP method proved to be highly efficient amongst other prospecting methods targeted at recognizing zones of sulfide mineralization making up 91%, considering that in more than half cases the ore intervals were the case. In the Yakutian diamondiferous province the EMS-IP technology was approbated during three field seasons to accomplish the assignments on searching for kimberlite bodies under conditions of various geological types. As a result, the reference objects were distinguished, and geoelectric parameters of kimberlite pipes of explosion were defined.INTRODUCTION In the time span 2015-2016 in Gorny Altay the EMS-IP technology was approbated in the Novokuznetsk area. The on-land areal geophysical survey was performed by EMS-IP method applied to identify, outline and locate promising sites with Au-Ag-bearing polymetallic mineralization within surveyed areas. Compared to the hosting rocks, the sulfides contained in polymetallic mineralization are typified by low specific electrical resistivity (SER) and high polarization. The areal survey conducted via EMS-IP method provided spatial characteristics of searched object. From July 2016 to August 2017 our expedition group carried out serial test works and laboratory investigations intending to define performance capabilities of EMS-IP technology in searching for kimberlite bodies under conditions of diverse geological types. The prerequisites for serial work were operations accomplished at the «Listvenichny» site lying 35 km away from Mirny town in the Sakha Republic (Yakutia), where the EMS-IP technology was probed for locating position and measuring geoelectric parameters of tuff pipe «Buardakhsky». After successful completion of operations it was decided to evaluate geoelectric parameters of kimberlite pipes of explosion."

Jan 1, 2018

By Hongli Wen, Guangkun Shen, Qiong Deng, Shoujian Huang, Min Gan, Xiaohui Fan

"Due to the low iron grade and high sulfur content, pyrite cinder is difficult to be directly used for iron-making. In this paper, technology of magnetic roasting -grinding and magnetic separation -acid leaching was put forward for reclamation of pyrite cinder. For pyrite cinder of TFe53.51%, S2.20 %, studies showed that good magnetic effect can be achieved at roasting temperature 650~7000, reducing atmosphere CO/(CO + C02) 10~20% and roasting time 10~30 minutes. In separation conditions of grinding size -0.045mm accounting for 96.09% and magnetic field intensity of 1240 GS, iron concentrate of TFe64.81 %, S0.18% and iron recovery rate 91.44% was achieved. Acid leaching was studied to strengthen desulfurization. Results showed that high-quality iron ore concentrate of TFe66.3 l %, S0.10% was obtained under the conditions of hydrochloric acid mass fraction of 5%, pulp density of30%, leaching temperature of70? and leaching time of2 hours.IntroductionPyrite cinder is produced as a by-product of sulfuric acid industry [1] Domestic production is more than 12 million tons every year and occupied area is over 10 million square meters [2,3]. The pyrite cinder outdoor not only pollutes air but also damages surrounding surface [4] It after treatment used for iron-making is an ideal reclamation approach for its rich iron which is commonly 40-60% [5]. But pyrite cinder gets low utilization for its low iron grade and high sulfur content in China [6]. Therefore, comprehensive utilization of pyrite cinder has profound significance to environmental protection and the development of domestic iron and steel industry."

Jan 1, 2013

To minimize the equipment operator?s respirable dust exposure in enclosed cabs of mobile equipment by install-ing cab filtration and pressurization systems and by keep-ing doors and windows closed. Background Enclosed cabs are used on mobile equipment to protect operators from health and safety hazards. The primary health concern is overexposure to respirable dust. Examples of such equipment in mining include drills, dozers, haul trucks, and other equipment. When equipment is new, the operator?s dust exposure is normally at acceptable levels. As the equipment ages and gaskets and seals deteriorate, the air quality inside an enclosed cab can reach a point where it is no longer at acceptable levels for the equipment operators. In an effort to improve the air quality in enclosed cabs of older mining equipment, NIOSH has been performing research to retrofit cabs with new filtration and pressurization systems. Over the past few years, this research has shown that retrofit systems can substantially improve the cab?s air quality back to safe and acceptable levels. How-ever, this is only possible when a positive cab pressure is achieved and maintained. Thus, when a cab door or window is opened, the cab pressure drops to zero and the cab filtration and pressurization system is rendered ineffective. During a recent field study, the magnitude of this impact was noted when a drill operator repeatedly opened the cab door throughout the course of the drill cycle. Upon closer examination, it was determined that the cab door was being opened to manually guide the next drill steel into place each time an additional section of steel was needed to drill deeper holes.

Sep 1, 2008

By Zheng-qi Guo, De-qing Zhu, Feng Zhang, Jian Pan

Iron mainly exists as the magnetite and fayalite, while copper is primarily dispersed in the form of fine matte particles in the copper slag, which is difficult to recover by conventional separation techniques. In this paper, the feasibility of an integrated technological route to improve beneficiation of copper and iron components from copper slag through the modification of molten slag was investigated, and the results shows that: the copper grade of rougher copper concentrate was increased from 6.43 to 11.04%, iron recovery from magnetic separation was increased significantly from 32.40 to 63.36%, and other evaluation indexes were changed slightly, in comparison with unmodified copper slag. Meanwhile, the grains of the target minerals in the modified slag grew considerably to a mean size >50 lm after slow cooling. Ultimately, the beneficiation efficiency of copper and iron was improved because of the ease with which the target minerals were liberated.

Mar 1, 2017

By K. Halada

Current trend of the global flow of strategic metals are analyzed to discuss the strategy of the development of recycling technology and alternative technology. In many cases, each global flow of metal is changing from the trilateral structure of U.S., EU and Japan in the later 20th century into the convergence to China as the factory of the world. Scrap flows are also changing dynamically. A long term change of prices of metal has gotten changed since the entrance of this century. The estimation of metal consumption up to 2050, in which the author estimated that many kinds of metal will overshoot the reserve base line, is revised considering these change of current trends.

Jan 1, 2014

"An innovative concept is proposed whereby the operating power for haul trucks in certain areas of an underground mine are reduced in order to lower ventilation costs. Airflow that must be provided for diesel-powered equipment in most jurisdictions are regulated based on engine peak power capability and engine emissions, both of which can be lowered by artificially reducing the capacity of the engine through the engine control unit. Advances in asset tracking and ventilation on demand enable this methodology and this study demonstrates that it could represent significant value for mine operators. An examination of haul truck duty cycle indicates that de-rating of engine operating power based on the truck’s location in the mine can enable a step change in ventilation rates, often with no material impact on working conditions. Methods for implementation and estimate of cost savings will be defined.INTRODUCTION Ventilation of underground workings remains a significant operating cost burden for modern mine operators. In particular, ventilation rates for underground diesel mining equipment are often defined by local regulatory bodies and are assumed to present minimal opportunity for optimization or savings, at least until battery propulsion systems can be adopted. Commonly, the quantity of air flow required is defined by the peak rated engine output power of diesel equipment. For example, Ontario Regulation 854 SS 183.1 (3) states that “The flow of air must be at least 0.06 cubic metres per second for each kilowatt of power of the diesel-powered equipment operating in the workplace”. Jurisdictions that define air flow using the prescribed CANMET or MSHA ratings use peak engine emissions to calculate air flow required for dilution ventilation. These approaches are similar in that the maximum power capability of a vehicle’s engine is used to define the ventilation rate in all areas where it travels, regardless of what power output is actually used in any of those areas. Examination of the duty cycle of a typical underground haul truck identifies a large variance in the power output of the vehicle depending on its location in the mine and the activities undertaken at these locations. For example, travel on a mining sub-level requires a fraction of the truck’s peak power due to the minimal grade and significantly reduced travel speed. So if we can reliably reduce the peak engine power capacity and engine emissions in areas where peak power is not required, we can logically cut the ventilation rates for those areas."

Jan 1, 2017