Search Documents

By Denise Y. Dixon

The objectives of this study were to (1) document the hydrologic impacts of longwall mining on ground water, (2) identify the factors which affect the extent of dewatering, and (3) develop empirical trends to predict the extent of dewatering and recovery in advance of mining. The study was confined to three mine sites in north-central West Virginia. At each site, available ground water supplies were identified and monitored for dewatering effects and recovery. Mine A, located in Upshur County, West Virginia, has relatively thin overburden (approximately 715-280 feet). At this site domestic water supplies and specially constructed monitoring wells were monitored, continuing with an earlier study done by Cifelli arid Rauch. Most such supplies were completely dewatered over the longwall panel. Some of these wells have shown significant recovery, especially near a stream. Extensive monitoring of two nested piezometer wells revealed that dewatering generally started in advance of undermining in the lowermost monitored overburden zones first and then progressed upwards. Most dewatered wells completed in bedrock have shown no recovery, except. for valley drilled wells located within 100 feet of a Stream. Affected dug wells completed in valley alluvium rend located within 200 feet. of the nearest stream have shown significant recovery. Some wells have partially collapsed following mine subsidence. Mine B, having relatively thick overburden (approximately 585 to 900 feet), is located in Monongalia County, West Virginia. Ground water supply surveys have been conducted there in an attempt to study past dewatering effects. Owners reported Chat several wells were dewatered by longwall mining arid vertical air shafts that preceded longwall mining. Dewatered wells over longwall panels hove shown some recovery within 3 ½ years of mining. Mine C also has relatively thick overburden (approximately 585-900 feet), and is located mostly in Greene County, Pennsylvania. In addition to a survey of domestic water supplies at this site, five specially constructed monitoring wells were tested. The shallow monitoring wells suffered drops in water level due to mining but totally recovered within one day to three weeks after dewatering occurred. However, they did occasionally exhibit partial collapse during mine subsidence. Subsidence fracturing was beneficial in increasing the lateral hydraulic conductivity by a factor of about S to 22 for rock strata located within 124 feet of the surface, indicating enhanced shallow aquifer potential. One deep well suffered both partial dewatering and structural damage, with the state of water recovery bring uncertain. Also, two shallow domestic supplies out of five located over the mine were reportedly dewatered, but this claim could not, be substantiated.

Jan 1, 1988

By Jun Xiao, Yucai Zhou, Yanhong Dong, Daixiong Chen

"In this article research on the mineralogical characteristics and beneficiation process for a copper molybdenum deposits in Heilongjiang province of China has been carried out. Chemical analysis, X-ray diffraction(XRD) and Quantitative Evaluation of Minerals by SCANning electron microscopy (QEMSCAN) were conducted on samples. The bulk analysis results showed that: (1) Comprehensive recovery and separation of molybdenum & copper minerals was feasible by the flowsheet of first copper-molybdenum mixed flotation after grinding the ore samples to 61.88% -74µm and then separation flotation of copper and molybdenum after regrinding the Cu-Mo mixed concentrate to 83.26% -38 µm. The results highlight relationship between mineralogical characteristics of ore and comprehensive benefication method. (2) the combination of "" Sodium sulphide and sodium thioglycolate "" reagents are effective inhibitors of copper-molybdenum mixed concentrate, their selectivity performance is better than that of single reagent. Good flotation indexes were gained that might be directive experience to similar cases. KEYWORDS Mineralogical characteristics; molybdenite; chalcopyrite; flotation separation; inhibitor INTRODUCTION Copper and molybdenum metals are widely used in the field of metallurgy, aerospace, national defence, etc. Copper –molybdenum sulphide ore is an important source of copper and molybdenum metals. At present flotation is still the preferred methods to deal with the copper-molybdenum sulphide minerals (Yin, Z., Sun, W.et al. 2017; Ansari, A., & Pawlik, M. 2007; Hirajima, T., Miki, et al. 2017). Copper and molybdenum sulphide ores usually have the similarly good nature floatability(Miki, H., Matsuoka, et al. 2017), meanwhile most molybdenum sulphide ore has tiny grained-size(Castro, S., & Laskowski, J. S. 2015.) and closed relationship with other sulphide and gangue minerals which result in the coper and molybdenum separation problem. Base on the nature of the ore and flotation properties of the individual minerals contained in the ore, there are two methods are usually used to deal with the copper – molybdenum ore, including bulk molybdenum/copper flotation followed by separation of copper and molybdenum minerals, sequential molybdenum/ copper flotation(Liu, G. Y., Lu, et al. 2012). The latter method has the shortcoming of hard to activate the depressed copper minerals in the previous molybdenum flotation process, which may result in a large loss of the copper from concentrate, this disadvantage would avoid while adopting the former method. bulk flotation followed by separation process is to get the copper-molybdenum concentrate from raw ore first then separate flotation the molybdenum and copper minerals, benefit from the excellent floatability of both molybdenum and copper minerals ( Malhotra, D., Rowe, R. M., & Bhasin, A. K. 1986; Cao, Z., Yue, et al. 2017 ), it really easy to obtain the mixed concentrate. In order to get the high quality copper and molybdenum concentrate, the key technologies and difficulties are to realize the separation of the copper and molybdenum minerals which have the very similar natural floatability (Raghavan, S., & Hsu, L. L. 2015; Nakhaei, F. 2014)."

Jan 1, 2018

By M. M. Fine

The flotation work on samples from nine fluorspar properties in Crittenden and Livingston Counties, Ky., reported herewith was part of a wartime project that resulted in increasing the supply of metallurgical-grade fluorspar. The samples were tailings, dumps, and waste rock that had been rejected in previous milling operations. All were treated successfully by flotation to yield metallurgical-grade concentrates with recoveries ranging from 77.5 to 98.3 percent of the fluorite. After the laboratory testing, the results of which were available to the owners and operators of the properties, many of the tailing ponds and rock dumps were milled. The real value of this report, therefore, is to show the operators of gravity concentration plants the possibilities of re-treating waste products by flotation either at some future time or currently with the gravity

Jan 1, 1948

By Xiaoqiong Wang, Daobing Wang, Fanbao Meng, Jianbo Wang, Hongkui Ge

"Shale gas has become an important unconventional oil and gas resources. Its effective development relies on comprehensive and accurate understanding of shale gas reservoirs. Rock mechanical properties is one of the important components of reservoir evaluation. Two adjacent black shale samples, which are cored from the depth of 1145 meters in Chongqing, southwest China, are subjected to acoustic emission(AE) test under uniaxial stress and compared with coarse grained granite. The results of synchronous AE, stress-strain and ultrasonic velocity experiments show that shale has weak anisotropy. Compared with granite sample, two shale samples are similar, but their strength, velocity and brittleness are quite different, indicating that shale has strong microscopic heterogeneity. TOC, XRD, SEM microstructure analysis show that total organic content, mineral composition and natural fractures are the main impacting factors for mechanical heterogeneity. INTRODUCTIONShale gas is a typical low-grade marginal resource, which is characterized by ultra-low matrix permeability and small single well control volume. In order to enable commerical development, complex hydraulic-fracture networks must be created in the shale to allow gas to escape from the micro/nano-pores and natural fractures where it is trapped in the rock (C. Clark et al.,2013; Ge et al., 2013). The development of shale gas requires accurate evaluation methodologies to evaluate shale reservoir properties and predict production. (Jarvie et al., 2007). Rock mechanical properties are an important part of the reservoir evaluation. It is significant for efficient drilling, completion and hydraulic fracturing to understand mechanical behavior of shale gas play (John, 2011; Wei, 2013).Rock mechanical properties mainly include heterogeneity, anisotropy, brittleness and acoustic emission activity (Lockner et al., 1992; Jerome et al., 2009; He et al., 2010; Liang et al., 2012). Shale mechanical properties are evaluated from laboratory tests following a complex workflow that covers tasks from sampling to testing (Md. Aminul Islam et al., 2013). It is common to include various experimental methods such as stress-strain curves, ultrasonic velocity and acoustic emission when evaluating the mechanical properties (Rao et al., 2006). Because of the presence of organic-rich matter, mineral composition orientation and natural fractures, shale tends to have strong anisotropy and heterogeneity (Deng et al., 2004; Wang et al., 2013; Hathon et al., 2013)."

Jan 1, 2015

By C. Doyle, J. Brennan, C. Díaz, J. Hrepic, K. Cushnie

"In 1991/1992, INCO undertook a successful R&D program aimed at extending the lining lives of the top blown rotary converters (TBRCs)at its Copper Cliff Nickel Refinery (CCNR) and the electric furnace at INMETCO. At the laboratory scale, this effort was divided into three phases. In the first part, mineralogical work was performed on six refractories that were either currently being used to line these vessels or were considered suitable alternatives. In the second part, this mineralogical knowledge was used to help determine the compositions of slags that would not corrode the bricks at the operating temperature (1600°C) of the above furnaces. Finally, several important properties of the six refractories were measured to complete their evaluation as candidate linings. This paper reports the results of all three phases of the laboratory scale R&D work.The mineralogical work showed that rebonded fused grain magnesite-chrome (RFG-MC) bricks consist principally of periclase with minor amounts of free chromite and trace quantities of silicates monticellite and sometimes olivine. The bricks are principally held together by periclase-periclase direct bonding. Of note, the bulk of the chromite exists as exsolved precipitated blebs within the periclase grains. These likely redissolve at high temperature.Slags on the periclase liquidus coexist stably with these refractories. Examples are presented using CaO-MgO-Al2O3-SiO2 slags at~1600°C.Finally, the two refractories manufactured using close to 100% fused grain material generally outperformed the others in terms of physical properties and certainly were superior in their resistance to slag penetration damage."

Jan 1, 1997

By J. G. M. Mukoya, B. Adebayo

"This work was carried out to determine the influence of rock properties and drilling machine parameters on the penetration rate at the SJ pit of Rössing Uranium Mine, Namibia. Rock properties (uniaxial compressive strength, tensile strength, and modulus of elasticity) of samples collected were determined in the laboratory. Drilling experiments were conducted in which feed pressure, air pressure, rotary speed, weight on the bit, and torque were varied to measure their effect on the penetration rate. The uniaxial compressive strength varied from 90–180 MPa for layered marble-quartzite and banded gneiss. Increases in feed pressure, weight on the bit, and rotary speed beyond the optimum level led to a decrease in penetration rate and caused the drill bit to ‘stall’. Results of the study revealed that penetration rate increases with an increase in the feed pressure and air pressure. After reaching a maximum value, the penetration rate begins to decrease despite increasing feed pressure. A very high torque causes the drill bit to stall, since the feed pressure is too high and the air pressure is not sufficient to remove the cuttings from blast-hole at maxium bailing velocities. The average penetration rate varied from 19 to 45 m/h for phase 2 of the pit, and from 17 to 68 m/h for phase 3. The optimum drilling machine parameters obtained in phase 2 and phase 3 were slightly lower than those currently being used at the mine. The trials of the optimum machine parameters will assist in reducing the cost of drilling, which varied from N$29.48 to N$36.31 per metre for the tricone bit. IntroductionDrilling and blasting contribute most to the operational cost in opencast mining and have the potential to influence the cost of downstream operations (Aipanda, 2011). The drillability of rocks depends not only on the rock properties, but also on the drilling tools and operational variables. In rotary drilling, rotational speed, thrust, and flushing are the operational variables, and are known as the controllable parameters. Rock properties and geological conditions are the uncontrollable parameters. Although, many attempts have been made to correlate drillability with rock properties, the rock characteristics affecting rotary drilling have not been entirely defined (Hartman, 1962; Kahraman, Bilgin, and Feridunoglu, 2003). The drill bit is forced into a rock surface from the rotary power head, hence creating stresses and cracks at the bit-rock interface. The performance of a particular bit in any formation i"

May 1, 2019

By Zay Jeffries

TUNGSTEN has the highest melting point of all the known metals, namely 3350° C.; it is one of the hardest of the metals; it has the highest equiaxing or recrystallization temperature after strain hardening, of any pure metal known. It is particularly distinguished because, when composed of small equiaxed grains, it is extremely. brittle and fragile at room temperature, and when possessing a fibrous structure it maybe ductile and pliable at room temperature. The common ductile metals act in exactly the opposite manner in this respect. The present paper will include a brief note regarding the manufacture of wrought and. ductile tungsten. The metallography of wrought and ductile tungsten in the various stages of manufacture will be considered more or less in detail. The general relationships between the properties of tungsten and other metals will also be considered. A discussion will be given explaining why fibrous tungsten is ductile at room temperature, even though past experience with other metals would indicate that it should be brittle. Finally, a brief note regarding some new fundamental metallographic propositions relating to all metals will be given.

Jan 6, 1918

By E. M. De Souza, A. M. Coode

"When Canadian potash was brought into production in the 1960s substantial research was carried out to develop the technology needed to cope with the unique conditions in Saskatchewan mines. The intense research has established Saskatchewan's position as a leader in production technology on a world scale, and as a leader in setting international standards for potash production. The industry is now more than two decades old and, although the mines operate efficiently, there are a number oj prominent areas of concern. High among these is the prediction, prevention and control of sodium rich brine inflows. Control has proven difficult or elusive in the potash mining horizon, but work continues in this area. Control of brine in the superincumbent limestone formation has proven to be easier and more conclusive.The first part of this paper describes the rehabiltation, diamond drilling, and grouting completed at Central Canada Potash, which reduced the brine inflow from approximately 82 l/min . at the beginning of the work to O.9/1min. when the backfilling was placed.The second part of the paper describes the rationale for choosing the rock mechanical instrumentation, the reasons for their placement and the rock mechanical data recorded with some interpretation.IntroductionCentral Canada Potash is located approximately76 km southeast of Saskatoon, near the Yellowhead Highway. The commercial production of potash at CCP started at the end of 1969 at a depth of 1021m below surface. The potash zone, which is presently mined, is approximately 3.35 m thick . Stress relief methods using yielding pillars are used in the design of the mining layouts. The planned extraction ratio averages 35070 . The mine is designed to produce approximately 3.3 million tonnes of sylvinite per year to give approximately 1.3 million tonnes of finished product (muriate of potassium) per year."

Jan 1, 1990

By G. K. Nimal Subasinghe

The performance of Knelson Concentrators (KC) used in gravity gold circuits often rely on manufacturers recommendations for selecting operating parameters such as, fluidising water flow rate and cycle time. These parameters are not only dependent on the machine parameters but also on the feed characteristics such as, size distribution of the gold and gangue particles and the composition of its constituent minerals. Particles entering a KC experience a centrifugal acceleration due to the high bowl rotational speeds. The required centripetal force to maintain a circular orbit is provided by the fluid drag force created by inwardly moving fluidising water and the Bagnold?s force arising from the particle/particle collisions. When the fluidising water flow rate is low particles move towards the outer rim of the bowl forming a packed bed within the grooves. On the other hand, if the fluidizing water flowrate is high the bed expands and some particles would move towards the centre of the bowl and gets carried to the tailings stream, thereby reducing the amount of material retained within the grooves of the bowl. Based on a force balance on a particle captured within the KC, a criterion which can be used to predict the amount of material recovered in the bowl has been derived and validated by experimental data. It has been shown that this criterion may be used to demarcate the transition of the bed from a packed-bed state to a fluidised state depending on the fluidizing water flowrate. By identifying the conditions for the optimal expansion of the bed comprising different constituent mineral particles, it is possible to estimate the optimal fluidising water flow rate that would maximise gold recovery while minimising gangue recovery. It was also observed that the accumulation of valuable mineral in the bowl takes place by the displacement of the gangue particles in the bed by the incoming heavy mineral particles. The kinetics of this segregation process was also studied using synthetic mineral mixtures. The experimental data suggests that this process follows first order kinetics and that the build up of heavy mineral reaches a maximum which could be used to identify the optimal cycle time. In this work, the suitability of the above model in optimizing the performance of a KC have been reviewed. Also the necessity and merits of testing an unaltered

Jan 1, 2014

By Mariana Boger Netto

O fósforo é um elemento crítico para a qualidade dos aços, tornando a redução dos teores desse elemento uma exigência para a indústria siderúrgica. Uma forma de se medir a eficiência da desfosforação é através do coeficiente de partição do fósforo (Lp=%P(escória)/%P(aço)). O objetivo principal deste trabalho é avaliar escórias de um forno elétrico a arco através da comparação entre o Lp real com o Lp calculado por simulação termodinâmica, avaliando, também, o comportamento da partição de fósforo com relação à composição química. A partir de dados de composição química de amostras de escória e aço de uma usina siderúrgica, foram feitas simulações termodinâmicas utilizando o software FactSage. Com base nesses resultados, concluiu-se que o cálculo computacional através do software descreve bem o comportamento termodinâmico, mas tende a superestimar o Lp, provavelmente por questões cinéticas e/ou de transferência de massa e calor.

Aug 17, 2017

By X. P. Guo

In this paper the test results of flotation of the kyanite ore from a Chinese mine are described. The objective of this work is to determine effective recovery process to obtain kyanite concentrate with high quality and high recovery for a new concentrator design. The valuable minerals of the ore are kyanite, garnet and magnetite, contents of them are 14.0%, 5.9% and 1.2%, respectively. The gangue minerals are mainly biotite, feldspar and quartz, contents of them are 33.8%, 17.8% and 25.6%, respectively. The kyanite in the ore contains a little iron. In laboratory flotation tests the factors affecting the flotation such as slime, alkalinity of pulp, and flowsheet configuration are studied. The interference of biotite on kyanite flotation as well as selective flotation of garnet is examined. On the basis of above-mentioned results the flowsheet of ore treatment comprising de-sliming, mica flotation, low intensity magnetic separation of magnetite, high intensity magnetic separation of garnet and coarse biotite as well as flotation of kyanite is pre-sented for comprehensive recovery of kyanite, garnet and magnetite. The kyanite concentrate con-taining more than 59% Al2O3 is obtained with a kyanite recovery of 70.0%. The contents of Fe2O3and biotite in kyanite concentrate decreased from 2.02% and 5% to 1.30% and 1%, respectively. The disadvantage of low kyanite grade in raw ore is compensated by accessory recovery of garnet and magnetite in the ore.

Jan 1, 2014

By A T. Spathis

Corrections are given for “A three parameter rock fragmentation distribution” by A.T. Spathis (Measurement and Analysis of Blast Fragmentation, Workshop hosted by 10th International Symposium on Rock Fragmentation by Blasting, New Delhi, India, November 25-29, 2012 pp. 73-86). Typographical errors in two equations for the uniformity index in the two versions of the original and modified Kuz-Ram model are corrected. It is noted that the modified equation in the original published paper of Cunningham also had the same typographical error. A corrected plot of the dependence of the uniformity index versus the burden to diameter ratio is given. These corrections do not affect the rest of the original published paper.

Jan 1, 2013

By Robert B. Parsons

"This article addresses the relationship between mine evaluation, the tax system, and economic risk. It is based on a paper presented by the author at recent seminars in Moscow and Tashkent on the subject of mine evaluation.IntroductionTaxation can have a strong influence on the feasibility of a mining project. For the most part, because metal prices are determined on a global basis, the mining concern is not able to pass on to its customers any portion of taxes which the concern has to pay. Taxes are a direct charge against the project. The purpose of the article is to highlight the various ways whereby different taxes can affect the financial viability of a mining operation.The first part of the paper identifies different forms of taxation, and the second part of the paper addresses the different forms of taxation in terms of risk analysis and impacts on the mining project. Finally, the third part of the paper makes brief mention of using the taxation system to provide incentives with respect to investment in mining activities."

Jan 1, 1993

By Nemick JA

Recent advances in computer simulation together with field measurements of caving and microseismic activity about longwall panels, has allowed a much better understanding of the caving process and the variability due to geology. The joint research between SCT Operations and CSIRO Division of Exploration and Mining has initiated new methods of computational modelling predicting various caving patterns and strata failure far ahead of the longwall face. This work was validated by field measurements of caving and microseismic activity at the longwall face.The rock fracture distribution and the caving characteristics of a range of strata sections have been simulated by computer methods. Validation studies of the method were addressed together with case studies. The interaction of caving with support convergence and face control is presented. The method allows the simulation of longwall support behaviour under various geological conditions. The system also allows a prediction of the monitoring data, which is best suited to give an early warning of weighting events or signal various key caving characteristics.

Jan 1, 1998

By G Cao, Y R. Cui, J X. Zhao, H P. Gui, G H. Wang, Z M. Wang, M M. Ren, B Li

Pyro-metallurgy is still the main process for lead production and a lot of lead direct smelting processes have been developed in recent years. All the processes will experience two steps in common. The first is the oxidisation of PbS to PbO and then reduction from PbO to Pb, furthermore, from ZnO to Zn. So, the composition of melts, especially the slag composition at reduction step change continuously. Up to now, there are few systematic results on the slag physical-chemical properties with its composition change. In this work, the typical lead direct smelting processes were analysed from theoretical and practical standpoints. The full-period slag composition and slag melting point change were compared. Especially, to the PbO and ZnO reduction steps, based on the full-period slag composition change, the slag properties were predicted. Based on dust composition and test results, the mechanism of Pb compound evaporation and its effect on practice and measurement of high PbO bearing slag physical-chemical property is discussed. It is suggested that to restrain the evaporation in practice and to obtain more accurate measurement results of physicochemical properties of smelting slag are the key problem not only to set high efficiency, energy saving process, but also to environmental pollution control.

Aug 21, 2024

By J. J. Thomas, J. H. Nead

This investigation was undertaken to determine, if possible, the relation between static and dynamic tensile tests as measured by the work required to break test specimens slowly, in a tensile testing machine, and rapidly, by means of a falling weight. It was hoped that the investigation would throw some light on the role played by ductility under different rates of application of load. In problems of design, it is usually assumed that the moduli of elasticity of all steels are equal; viz., about 30,000,000. The stress-strain diagram within the elastic limit is a straight line, as shown in Fig. 1, where OA is the curve of a hard steel and OB that of a soft steel. If the modulus of elasticity is constant, as assumed, the slope of the line OC

Jan 1, 1922

By J. H. Nead, J. J. Thomas

This investigation was undertaken to determine, if possible, the relation between static and dynamic tensile tests as measured by the work required to break test specimens slowly, in a tensile testing machine, and rapidly, by means of a falling weight. It was hoped that the investigation would throw some light on the role played by ductility under different rates of application of load. In problems of design, it is usually assumed that the moduli of elasticity of all steels are equal; viz., about 30,000,000. The stress-strain diagram within the elastic limit is a straight line, as shown in Fig. 1, where OA is the curve of a hard steel and OB that of a soft steel. If the modulus of elasticity is constant, as assumed, the slope of the line OC

Jan 1, 1922

By J. P. Hansen

In order to help assure an adequate domestic supply of minerals essential to the Nation's economy and and security by developing more efficient minerals extraction technologies, the Bureau of Mines Tuscaloosa Research Center examined the application of autogenous microgrinding to calcium carbonate minerals. Treatment of minus 8-mesh Alabama marble resulted in a product 80 pct minus 5 micrometers (µm) at a power consumption of 70 to 80 kwhr/ton, This study shows that coarse particles of calcium carbonate minerals are effective as the grinding media for the autogenous attrition grinding of these minerals. The minus 8- plus 30-mesh fraction is an effective grinding medium (sand) for particles smaller than 30 mesh. A 40-pct-solids slurry and a sand: marble ratio of 2.5 appeared to be near optimum. For residence times above 13 minutes, products were greater than 80 pet minus 5 µm and greater than 54 pct minus 2 µm. Power consumption was uniformly low, ranging from 50 to 100 kwhr/ton of product depending upon the feed rate. One marble sample from Georgia was shown to be the most persistent grinding medium, with losses of less than half those of the other materials tested.

Jan 1, 1980

By Roger Potvin

Abstract The demand for pure zirconium and titanium metals in Germany increased considerably during the war. Pure zirconium was used in flash bulbs, in vacuum tubes, and in time fuses for bombs, where it has a decided advantage because it gives no gas in burning. Under the form of alloy, it was used with other rare elements for making substitutes for platinum; it was also used as a scavenging agent in high-grade steels. Metallic titanium was mainly used in connection with the manufacturing of special alloys. The authors were sent to Germany by the Department of Reconstruction and have investigated the German process developed for producing these rare metals. They describe the procedure and special equipment used for their commercial production in Germany during the war. General Metallic zirconium and titanium were .produced on a commercial scale in Germany by the thermal reduction, with metallic sodium, of potassium fluozirconate and titanium chloride, respectively, using a mixed potassium and sodium chloride flux. According to the information gathered, the sole German producer of these rare metals in pure form was the Deutsche Gold und Silber Scheideanstalt (commonly called Degussa), at their Werk II, 215 Gutleutstrasse, Frankfurt/Main, which was visited by the authors on September 18th, 1945. As far back as 1934, Degussa was carrying on active research on the manufacture of zirconium, and nearly one ton of the pure metal had been produced before September, 1939. Concurrently, a quite similar process was worked out for the recovery of titanium and it was in commercial operation in the year 1938, during which the production totalled about half a ton (metric). The demand, especially for pure zirconium, increased considerably during the war, attaining a total of about 48 tons during the period October, 1939, to the end of 1944, and reaching a peak of more than 15 tons in 1943. In 1944, the plant was slowed down due to the frequent and disastrous bombing by the Allies, especially in March and September.

Jan 1, 1946

NEW MEMBERS The following list comprises the, names of those persons who became members during the period June 10 to July 10, 1914: Members ALDRICH, HAROLD W., Supt. of Leaching Plant, Washoe Red. Wks., Anaconda Copper Co., Anaconda, Mont. AYER, FRANK ASHTON, Mine Foreman.. ..Detroit Copper Co., Morenci, Ariz. BELL, ARTHUR F. L., Chief Engr., Associated Oil Co.., 817 Sharon Bldg., San Francisco, Cal. BERGMAN, JULIUS GUSTAF, Mech. Engr., Chief Draftsman, Arizona Copper Co. Morenci, Ariz. BURT, CURTIS F., Min. Engr., Pittsburg-Dolores Mining Co., Rockland, via Yerington, Nev. CALLAWAY SCOTT DAVID, Chem La Harpe Smelter Co., La Harpe, Kan. CAMPBELL, W. C., Min. Engr 4 Princess St., Roodeport, Transvaal, So. Af. CARROLL, GEORGE A., Genl. Mgr Kildare Min. Co., Manson, B. C., Canada. CARUTHERS, JOHN LYTLE, Min. Engr., Asst. Engr., St. Louis, Rocky Mountain & Pacific Co.. Raton. N. M.

Jan 8, 1914