Search Documents

By J. S. Webb

This is one of a series of papers dealing with mining methods, practice, and costs be¬ing published by the United States Bureau of Mires. In this paper a description of the mining practice in vogue at the Braden unit of the Kennecott Copper Corporation is undertaken. PRODUCTION At present (1931) the entire production of ore is being obtained from the Teniente mine. The miring method in use is an adaptation of block undercutting which has been a development of the stoping and pillar caving experience obtained at this property. Improvements in mining practice are constantly being made.

Jan 1, 1932

By J. A. Herbst

Professor Klaus Schönert and his students used fundamental physics to develop many of the principles required for the design and scale-up of "Gutt Bett Zerkleinern" devices such as the high pressure grinding roll (HPGR) or the high pressure roll crusher (HPRC). As the equipment evolved so have the tools used for its selection and analysis. In the current paper discrete element modeling (DEM), Metso's proprietary Fast Breakage simulations, and Schönert's packed bed piston test are combined with energy based population balance models (PBM) to yield an alternative to ore characterization and equipment selection by pilot plant testing. The resulting methodology is used to take the next step in understanding these devices with a view toward predicting plant performance. This paper describes a journey beginning with precise modeling of a small HPGR including stud geometry and system hydraulics. A key to predicting performance is the accurate modeling of individual particles, their motion in the machine, the probability of breakage and redistribution of fragments, and the inter-particle breakage events that occur between the rolls at different pressures, speeds and moisture levels. Advanced DEM simulations and particle breakage characterization methods provide the necessary technology. The resulting combined models were validated using a small diameter laboratory scale unit. The validated physics based model was used then used to predict the performance of plant scale units using a specific energy based scale-up method. Scale-up results are analyzed in terms of power draw, throughput, and discharge product size distribution.

Jan 1, 2012

By Robert F. Griffith

In 1948 when the U.S. Bureau of Mines began the investigation of domestic monazite placers for the Atomic Energy Commission, deposits of this type amenable to large-scale operations were unknown in the U. S. Intensive search for such deposits had not been carried out in the past. Problems to be met included scarcity of men with placer experience and need for development of new exploration, evaluation, and analytical procedures. As a result of the exploration program three dredges have gone into operation in one area in Idaho and another dredge is operating in South Carolina. Search for Deposits In the search for areas to be investigated for monazite, the first step was a thorough study of all available literature reporting occurrences of the mineral. Initial work was guided largely by many reconnaissance reports prepared by the U. S. Geo- logical Survey and the AEC. As the work progressed many new deposits, not mentioned in the literature, were called to the attention of USBM engineers by prospectors who had noted the presence of the yellow, heavy sand while prospecting for placer gold. Every prospector was given an attentive ear.

Oct 1, 1955

By Carle R. Hayward

SulphuR has long been one of the banes of the steel manufacturer and often no effort and expense have been spared in order to reduce it to a small per cent. in the finished product. This condition is due to a general conviction that in many cases where steels have failed in service, sulphur has been the cause. But there has been a growing feeling in recent years that the verdict against sulphur has been unnecessarily severe. In cases of segregation it was present in. augmented amounts along with other impurities, but it had not caused the segregation. High sulphur in pig iron is caused by poor furnace conditions and the sulphur is merely one indication of an iron that has not been properly reduced. No amount of subsequent treatment under oxidizing conditions in the open-hearth furnace can remedy the defects, although the per cent. of sulphur may be considerably reduced. In other words, the causes of bad steel can frequently be traced back to bad pig iron, and sulphur is merely one indication that the pig iron is bad. The writer recently visited a steel plant where a mass of evidence had been accumulated which substantiated this fact, and the superintendent was emphatic in stating that high sulphur was not harmful provided the steel was not otherwise poor due to insufficient reduction in the blast furnace. The presence of a moderate amount of sulphur is desirable from the standpoint of the man who machines the steel. The low-sulphur material drags and the production of a smooth surface is very difficult. A slight increase in sulphur enables the machinist to produce a smooth surface without difficulty. Since, therefore, such large quantities of steel are subjected to machining, it becomes highly important that the sulphur controversy should be settled, and if its presence is proved to be harmless the ban on it should be lifted. Among the recent papers on the effect of sulphur on steel is one by Dr. J. S. Unger, Manager of the Central Research Bureau, Carnegie Steel

Jan 1, 1917

By R. H. Nafziger

Bureau of Mines research has shown that very low-sulfur pressure vessel steels with improved mechanical properties can be prepared by two melting processes. Four pressure vessel steels having sulfur contents ranging from 0.0008 to 0.0040 wt-pct, were produced by the electric-arc furnace or by the electroslag processes. Calcium carbide was used as a desulfurizer in the electricarc furnace. Fluxes containing at least 40 wt-pct CaO provided sufficient desulfurization during electroslag remelting. Element recoveries were higher for electroslag remelting than for metal melted in the electric-arc furnace. Bar rolled from electroslag-remelted ingots generally possessed higher tensile strengths and ductility than bar rolled from it t melted in the electric-arc furnace. Charpy V-Notch upper shelf energies were also improved as a result of electroslag remelting. The primary failure mode during impact testing was was microvoid coalescence. Sulfide inclusions were minimal, especially in the electroslag-remelted material.

Jan 1, 1979

By D. E. Ranta

Orebodies with intricate three-dimensional shapes (such as porphyry molybdenum deposits) are difficult to model using geostatistics or other computer-assisted methods. The strong trends in their spatial grade distributions occur as mathematically complex shapes and prevent the customary assumption of local stationarity that is required for accurate ore reserve estimation. "Zoned Kriging", a new method developed by AMAX, solves this problem directly by using the geologist's interpretation of the ore zones as a parameter in the kriging equations. The geological basis and methods used in the Climax ore zoning technique are reviewed and discussed relative to their application in zoned geostatistical modeling. The Zoned Kriging technique is described and demonstrated using data typical of mineral deposits.

Jan 1, 1984

By Yoginder P. Chugh

The control of soils has been found to be one of the highest priority factors influencing the return of reclaimed prime farmland to production. The compaction of soil is primarily a result of the movement of high ground pressure wheel scrapers and dozers over soils during the soils replacement and regarding process and occurs to a maximum depth of about 1.2 m (4 ft) The deleterious effects of soil compaction can be controlled by deep soil loosening to a depth of 1.2 m (4 ft). Most farm tillage equipment can only loosen soils to a maximum depth of 0.33 m (1.0 ft). Deeper soil loosening equipment, in the 0.33-1.2 m (1.0-4.0 ft) range is currently avail- able in the U.S. and abroad which may have potential for application on reclaimed prime farmland. This study has appraised such available equipment and the results indicate that a few manufacturers in the U.S., West Germany, and England market static and vibratory soil loosening equipment which have potential for deeper soil loosening of reclaimed prime farmland.

Jan 1, 1985

By Adriano Corrêa Batista, Bernardo Antônio Perez da Gama, Camila Freitas de Araújo, Paulo Santos Assis

O mexilhão dourado Limnoperna fortunei é uma espécie invasora que tem causado diversos problemas no ambiente aquático em razão da sua habilidade de formar colônias em estruturas. A espécie adere nas superfícies por filamentos proteicos, causando sérios danos ambientais, sociais e econômicos.O combate à incrustação biológica através do tratamento de superfícies submersas em ambientes de água doce com produtos naturais, em especial os oriundos de algas vermelhas, é o desafio apresentado.Com o banimento, em dimensão mundial, de insumos à base de tributilestanho - TBT na composição de tintas, desde 2008, tratamentos alternativos e ambientalmente adequados ganham maior apelo, considerando os riscos dos produtos alternativos atualmente aplicados. É descrito um conjunto de condições para espécies produtoras de metabólitos secundários com atividade anti-incrustante importante. Portanto, o trabalho tem como objetivo reforçar uma linha de pesquisa ampla dedicada a consolidar informações sobre o potencial de organismos marinhos como produtores de metabólitos secundários (produtos naturais) com atividade anti-incrustante, à luz da produção científica a ser analisada no espaço destinado à apresentação de resultados.

Nov 6, 2019

By R. C. Anderberg, F. J. Caervenyak, F. J. Frattali, H. J. Kandiner, R. A. Brown

"INTRODUCTION Considerable interest was shown .prior to and during World War II in the winning of metallurgical-grade alumina from anorthosite, kaolin, siliceous bauxites, diasporic clays, and other aluminum-bearing ores. Laboratory and pilot-plant investigations were made on many of these ores by the Bureau of Mines, and a series of reports on them is being prepared. This report covers the tests made on the application of the lime-soda-sinter process to anorthosite, which is a mixture of albite, NaAlS1308, and anorthite, CaAl2Si208. Extensive deposits of anorthosite occur in the Laramie Range in Wyoming and extend into Colorado; other deposits are found in New York, with outcroppings appearing in Vermont, Maine, and Labrador.Anorthosito can not be treated by the Bayer process for the production of metallurgical-grade alumina, because excessive losses of soda and alumina occur from the formation of sodium-aluminum silicate due to the large amount (50 percent) of silica in the ore.RESULTS OF INVESTIGATIONSSmall-scale laboratory tests supplemented by pilot-plant runs have demonstrated that the alunina and soda occurring in the Wyoming anorthosite from the Laramie Range can be extracted and recovered satisfactorily by the lime-soda process. It has been shown that liquors containing approximately 95 gram of A1203 per liter can be consistently produced at Na20:A1203 ratios from 1.75 to 2.27, and that these liquors can readily be desilicated and carbonated to yield high-grade alumina trihydrate of quality comparable to that essential for cell-grade alumina. The optimum results were obtained with Na20:A1203 mol ratio of 1.03 and Ca0:Si02 ratio of 2.14 in the sinter when calcined at an average temperature of 2,444ºF. for 25 minutes."

Nov 1, 1947

By Henry Kreisinger, WALTER T. RAY

This bulletin contains a statement of certain results that will be embodied in a report describing investigations of the combustion of fuel made by the United States Geological Survey and the Bureau of Mines in a specially constructed long furnace. The furnace forms part of the fuel-testing plant at Pittsburg, Pa., which was established and equipped by t.he Geological Survey, but passed under the control of the Bureau of Mines on July 1, 1910, when a t.ransfer of fuel-test.ing investjgations, authorized by act of Congress, became effective. The work discussed in this bulletin was done under the direction of the Geological Survey. The furnace was designed and built for an experimental study of the processes of combustiop, this study being part of a comprehensive plan for testing fuels to determine their heat value and the manner in which they can be used to best advantage. Although the main object of the researches made with the furnace by the Geological Survey was to examine critically the production of sensible heat by combustion along the path of the gases rising from the fuel, an interesting as well as important side problem developed in the study of the simultaneous dissipation of the heat through the walls and roof . of the furnace. Thus incidental data were collected on the temperature gradient through the walls at several places. These temperature data. (together with the heat conductivity of the material of the walls) formed the basis for calculating the heat dissipated through the walls. The object of this report is to present and discuss these temperature data. The discussion particularly concerns the air-space type of wall construction as compared with the solid brick wall or walls type, in which the air space is filled with some solid material of low heat conductivity. The conclusion of the authors, which perhaps will surprise some readers, is that, so far as loss of heat is concerned, a solid wall of brick or any ordinary material is preferable to a hollow wall of the same total thickness, especially if the air space in the hollow wall is near the furnace side. There is a general belief that l?ince air is a poor conductor of heat, air spaces built into the walls of a furnace will prevent or reduce heat dissipation through the wa.lls. Although there may be instances of furnace walls in which such construction reduces the rate of heat flow through them, yet as a rule the effect of the air space is just the opposite. While the heat does travel very slowly through the air by conduction, it leaps over the air space readily by radiation. Although this latter mode of heat propagation is common in nature, the laws governing it are not generall;y known and are seldom taken into consideration when furnace walls are being designed. It may be stated here that the quantity of heat passing through a. portion of a solid wall by conduction depends on the difference between the temperatures of the two planes limiting the portion of the wall. The quantity of heat that passes across the air space in the waH depends on the difference of the fourth powers of the absolute temperatUI: es of the surfaces inclosing Hie air space. It follows that, in case the heat. passes by conduction through the solid'portion of the wall, the loss remains approximately the same so long as the temperature of the two limiting planes remains constant, no matter what may be the temperature of the two planes. On the other hand, the heat passing across the air space by radiation increases rapidly with the temperatures of the inclosing surfaces, although the difference between these temperatures may remain constant. This feature will be shown by curves in the latter part of this paper and thoroughly discussed. The important point is that the air space, which is advantageous in the walls of a refrigerator because the temperatures are low, is objectionable in a furnace wall because the temperatures are high. It is customary to put air spaces in furnace walls between the firebrick linings and the common brick. Usually the fire-brick lining is only half a brick thick, which construction brings the air space too close to the furnace. The result is that the temperatures of the surfaces inclosing the air spaces are too high, and in consequence too much heat is radiated across the spaces. The heat passing through such walls would be much reduced if the air spaces were filled with brick, or, better, with some cheap nonconducting materials, such as ash, sand, mineral wool, etc. Even where the fire-brick lining is one brick thick (9 inches), the temperature in the furnace may be high enough to raise the temperatures of the air-space surfaces so much that the heat radiated across the space will amount to more than would the heat conducted through a filling, were the filling only common brick. This last statement is amply justified by the data here presented.

Jan 1, 1911

By H. Merton Ruth

THE northern anthracite fields, although facing the same economic problems as the southern fields, are confronted with the additional problem of fast dwindling reserves of anthracite which can be conventionally and economically won. The mining of coal which remains in thin beds and the recovery of pillars from areas heretofore considered unrecoverable, either by reason of cost or surface restriction, pose problems of in- creasing importance to the economic life of the northern field operations. Successful approaches have Been made to this problem and other work is being performed that holds promise. There exists in the northern anthracite field millions of tons of solid coal, the recovery of which has not been too successful due to the following inherent operating faults: inability to concentrate producing areas; the great quantities of rock to be cut and handled, lack of consideration of proper sequence and speed of second mining, and the continued use of the mine car as the basis of payment. A mining system that has successfully solved these major problems has been in operation in the Scranton area since 1944. Over 1% million tons have been produced from veins varying from 3 to 4% ft thick by this method, which is known as the multiple panel-triangular system-conveyor mining.

Jan 1, 1950

By Cary Hirner, Dan Lopez, Ross Webb, Stephen O’Connell

"Construction of the largest desalinization plant in the Americas has commenced in northern Chile. It is part of a several billion dollar expansion at a copper mine whose operations nearly stopped due to the challenge of securing a reliable source of water from the Pacific Ocean in a safe and environmentally sound manner. This paper discusses the risk management, design and construction of a quadruple chamber intake and outfall shaft, high capacity pump station, three 7m diameter vertically drilled marine shafts and three subsea tunnels constructed through challenging Andean hard-rock geology. The three 2.5m diameter subsea microtunnels are being mined with vertical curves through variable quality rock 30 meters beneath the ocean and retrieved in the wet from the 7m diameter marine shafts. INTRODUCTION AND BACKGROUND The battle for securing the rights to a constant water supply is a worldwide issue and nowhere is that more evident than the Atacama Desert of Chile, the world’s driest place with areas of the desert that have not seen rainfall in recorded history. The Atacama Desert also happens to be home to some of the world’s largest ore deposits which require huge amounts of water to extract and process. What available water there is comes from three main sources: deep seated wells, glacial water from the Andes Mountains, and desalinated water. Vying for water from wells and glacial streams and lakes are numerous agricultural and domestic facilities in the valleys surrounding the Atacama Desert. Environmental regulations and legal rulings have limited the amount of “natural” source water which can be used for mining purposes. Desalination plants are a known solution for combating water scarcity, albeit a costly one. The total estimated cost of constructing this desalination plant is over $3B USD, which will include a 2500lps capacity and an approximately 118km pipeline from the coast up to the mine located in the Andes. The overall scope of the project includes design, procurement, and construction packages for the 2500lps desalination plant including the seawater reverse osmosis plant, water conveyance to the mine, power transmission, the reservoir and the marine works package which forms the basis of this paper. Key components of the underground construction portion of the Marine Works are:"

Jan 1, 2016

By Fiona J. Stevens McFadden, Gregory J. Hardie, Mark P. Taylor, William Uru

"Over 20 million tonnes of installed aluminium smelting capacity exists worldwide, with smelter energy con.sumption in the range 14-17 kWh/kg aluminium. In terms of the reduction cell technology itself, the lowest sustained energy consumption is just below 13DC kWh/kg, or 50% energy efficient.For 15 years Comalco Aluminium Ltd. in Australia has been engaged in developing and testing reduction cells that use a refractory hard cathode, composed of a TiBif carbon composite coating over a carbon cathode. This technology has the potential to reduce energy consumption significantly while simultaneously increasing the life of the cells, which is currently limited by wear rate of the conventional carbon cathodes used throughout the worldIntroductionThe successful development of an aluminium wettable cathode technology affords the opportunity to the cell designer and smelter operator to fundamentally change the physical operating characteristics of the Hall-Heroult process. With this revolutionary capability in hand, published papers and patents have indicated that the technology may be exploited in a wide variety of ways to improve the economic performance of aluminium smelting process. Comalco has been developing refractory hard cathode technology for more than 15 years and has been exploring a number of ways that the technology may be commercially applied in a smelter operation [l]."

Jan 1, 2000

By Bryant Fitch

This paper will review thickening theory, from the ( ) of the practicing engineer, with particular emphasis on ( ) uncertainty or disagreement. It will attempt to outline broadly what we know and what we don't know. This should serve two purpose First, it will warn the process engineer where he might get into trouble. At least it will alert him to the risk involved in uncritically accepting any of the recommended design procedures. Second, it will identify for researchers some areas in which further work might be fruitful. Not too many years ago there would have been little to write on such a subject. We had been designing thickeners for decades, using the classic Coe and Clevenger procedure. As far as we were generally aware, they all turned out to be about the right size. And so if there was anything we didn't know, It certainly wasn't hurting us much. Today we know better. While it is true that in most cases units designed by the Coe and Clevenger procedure (1) will perform satisfactorily, we now know of cases in which they don't. And during the past few years there have been many developments and advances in basic thickening theory. So there is now a lot more room for disagreement, and a whole lot more to be uncertain about. What is "thickening" "Thickening" means different things to different people. For this paper we define it to mean sedimentation behavior characterized by line settling. Solids subside with a clear line of demarcation between settling solids and supernatant. Although the supernatant will usually be clear, in some cases it may be turbid. Line settling must entail that all particles just below the pulp-supernatant interface have the same subsidence rate, so that

Jan 1, 1971

By Weiran Zuo, Wanzhong Yin, Jin Yao, Keqiang Chen, Qiuyue Sheng, Liu Liu

It is important to investigate the liberation properties of gangue minerals and establish liberation models for low-grade iron ores to reject gangue early. In this study, three types of iron ores from different iron deposits were ground to different particle size distributions by locked-cycle grinding and batch grinding. The liberation distribution of quartz, the most dominant gangue mineral among the three types of iron ores, was tested by Mineral Liberation Analyzer (MLA). Afterward, the liberation distribution of the three types of quartz was fitted using the beta distribution function, and their shape parameters were related to particle sizes to develop the liberation model. MLA test results showed that the liberation distribution of quartz with different grinding methods was basically the same. The developed liberation model predicted the liberation distribution of quartz in low-grade iron ores from different iron deposits well, and its coefficient of determination (R2) was between 0.90 and 0.98. This study deepens the understanding of the liberation rules of quartz in low-grade iron ores from different iron deposits, and on this basis, a more efficient liberation model based on the beta distribution function is developed.

Oct 18, 2023

By L. F. Pett

ALTHOUGH Kennecott's orebody has long been outlined, it is still necessary to define further its limits. This mine, long an advocate of churn drill methods, recently supplemented its practice by using a diamond drill. So far, the diamond drill holes have been along the main canyon floor which traverses the mine area. This zone, highly fractured, is cut by numerous friable quartz veinlets encountered within the porphyry. These veinlets, formed by filling contracted porphyry fractures with hot, siliceous, mineral-bearing solutions, are often more highly mineralized than adjacent porphyry. They pulverize on contact, yielding only slight amounts of core.

Jan 7, 1951

By P. Croney

Environmental monitoring requires major effort and expense but management of data receives less attention. A modem database system can manage hydrochemistry, water levels, meteorology, geology and downhole geophysics data and is flexible to allow the storage of ad hoc data. Reports can be customized by the user and derived data generated from input values. The production of high quality maps with contours and hydrochemical diagrams is an essential part of the reporting process. These maps integrate directly with the current site survey information. These facilities are best provided by storing the data in an industry standard database such as Oracle or Access to which customized AutoCAD and Microsoft Office routines make direct SQL calls.

Jan 1, 1997

By Gamaniel Curasma

El Arco Peruano es un elemento de sostenimiento en forma de un arco de concreto armado con fierro de acero estructural de alta resistencia que se coloca entre las cimbras de acero en los tajeos de producción de la mina Yauricocha con la finalidad de controlar los altos esfuerzos que se producen por el minado masivo del método Sub Level Caving en la mina Yauricocha. Usualmente los altos esfuerzos del minado dañan de sobre manera a las cimbras de acero y en menos de dos meses de su instalación requieren ser reinstaladas para mantener una sección mínima operativa de 3.0 metros requerida para el ingreso de los cargadores de bajo perfil de 6 yd3 de capacidad. Es por esa razón que se implementa este nuevo diseño de sostenimiento en la minería, actualmente aplicado en los tajos de producción del cuerpo Esperanza.

Sep 30, 2022

Rep. William S. Hill (R.- Colo.) will preside over a Congressional hearing investigating the problems of the mining industry to be conducted in Phoenix, Ariz., late in April. Rep. Hill has expressed the desire to hear from the industry itself all possible testimony on the needs of domestic mining and how Congress can help. Rep. John J. Rhodes of Arizona is also expected to attend the hearing. Two new features are incorporated into an SO2 process for treatment of low grade manganese ores disclosed by Chemical Construction Corp. The new approach includes a high temperature autoclaving step and a sintering operation. Data was given for work performed on Cuyuna Range ores.

Jan 4, 1953

By F. Vahdatikhaki

Simulation techniques have offered significant boosts toward a cost-and-time-optimized planning of construction projects by enabling project managers to effectively comprehend the behavior of projects. Using historic data from projects of like nature, simulation considers uncertainties involved in a project through accommodating the stochastic modeling parameters. However, the heavy reliance on the statistical data and not taking into account the context-specific features of the project cause the degradation in the realism and accuracy of the simulation models. Similarly, the extent to which a historic pattern could be retrofitted to new projects will decrease in line with the growing uniqueness of the projects and the novelty of construction methods. Furthermore, the existing real-time simulation frameworks are not capable of distinguishing the transient environmental changes, with minimal long-term impacts on the productivity, from the influential changes that will greatly impact an operation. In addition, existing simulation tools are devoid of location awareness, resulting in the inability to consider safety threats in their representation of the project. To address these issues, this research proposes a framework based on the integration of new tracking technologies used in Automated Machine Guidance (AMG) with simulation-driven 4D modeling methods. The proposed framework automates the adjustment of the simulation model based on the updated data from the site, and thus transforms simulation from a predictive tool used at the planning phase to a proactive monitoring platform usable throughout the planning and construction phases. A prototype is developed to test and demonstrate the effectiveness of the proposed approach.

Aug 1, 2013