Search Documents

By P. S. Rao

In 1951, Tata Steel became the pioneer in Asia by setting up its first ever washery in West Bokaro Colliery. The first beneficiation plant used to produce clean coal of 19% ash with chance cone. Feed size of chance washers were -75 mm to +6 mm. The fine coal (-6 mm) were used directly. With change in technology,in 1986,chance cones were replaced by DM cyclones and coal was washed in two circuits. In the coarse circuit -13 mm to +0.5 mm coal was washed in two stages while the fine coal of -0.5 mm was treated in froth floatation cell. With further improvement in the process the higher ash raw coal was feed to produce clean coal of 13% ash. In 1998, DSM cyclones were replaced by scrolled Evolute design cyclone which has Ep of 0.020 to 0.025 ranges resulting in increase efficiency of separation. With the increase in demand of clean coal, lower seam proportion has increased in raw coal production. The washability studies of individual seams indicated large difference in the seam characteristics in terms of washability and specific gravity cut points of the individual seams. So washing all seams together had resulted in frequent change in the character of coal and warrants frequent changes in the operating parameters of the plant in which the separating efficiency comes down and ultimately resulted in yield loss initially. With increase in knowledge and experience in coal washing the solution to this problem was achieved by adopting, seam-wise washing which is enabling process engineers by keeping set point for longer periods there by to enhance the separation efficiency. Keywords: coal processing, froth floatation, steam washing

Sep 1, 2012

By John E. Trombly

System objectives and design criteria for an in-mine visual personnel paging system are discussed. Display technologies are evaluated and tradeoffs leading to display selection are described. The prototype dispatcher's console, battery/receiver box and visual display assemblies are functionally described. The report includes circuit descriptions, schematics, parts lists and equipment cabinet drawings for the three assemblies. The report concludes with an estimate of the manufacturing cost for each assembly.

Jan 1, 1975

By Yuji Yamashita, Kazuyoshi Kamimura, Tsuyoshi Takahashi, Naoya Matayoshi

"The CDM-LODIC method (cement deep mixing - low displacement and control) method enables ground displacement to be reduced by removing an amount of soil equivalent to that of injected cement slurry and the volume of the plunged mixing tool, which causes a certain degree of ground displacement. Since the CDM-LODIC method was developed in 1985, it has been applied to over 930 sites and the accumulated volume of stabilized soil has now reached 7.6 million cubic meters.In the CDM method, the number of blade rotations per unit depth in the ground when the mixing blades are withdrawn is considered a construction item. The blade rotation number depends on the degree of mixing between the cement slurry and the ground Some field tests were performed based on the degree of mixing between the cement slurry and the ground. In these tests, a new concept of evaluating the blade rotation number when the screw rod penetrates to a given depth without injecting cement slurry has contributed to the degree of mixing. Furthermore, a correlation exists between the coefficient of efficiency of soil removal and the cement slurry admixture rate. In this paper, we discus the data collected in those field tests and present some application examples.OUTLINE OF CDM-LODIC METHODThe injection of cement slurry may cause some ground displacement during Cement Deep Mixing (CDM). In recent years, due to an increased demand for ground improvement work in urban areas, there is increased concern that buildings near any CDM site may be adversely affected. The deep mixing method which reduces displacement due to mixing (CDM-LODIC method) enables ground displacement to be minimized by removing an amount of soil equivalent to the injected cement slurry and the volume of the mixing tool, which itself causes some ground displacement. When the construction site is near other structures, regardless of whether on or under the ground, the CDM-LODIC method can be used in order to minimize any ground displacement. There are considered to be two main causes of ground displacement as shown in Figure 1. Displacement A indicates ground displacement caused by the volume of the inserted mixing tool during the penetration stage and displacement B indicates ground displacement caused by the volume of the injected stabilizing agent. Thus, by removing soil equivalent to the volume of the inserted mixing tool and the injected stabilizing agent, ground displacement can theoretically be minimized. Figure 2 shows the amount of observed ground displacement in the cases of CDM and CDM-LODIC at an actual site. These case studies indicate that ground displacement can be reduced by removing the soil."

Jan 1, 2015

By Se-Won Chang

This is a part of the joint KIGAM-GNS-NIWA 3-year study of ferromanganese nodules on the Campbell Drift, east of Campbell Plateau to determine age distribution, growth rates and geochemical evolution in relation to geographic setting. During the research voyage SAA3 by R/V Tangaroa (TAN 9909) in July-August 1999, seafloor sampling and camera towing were conducted along the two transects across the known flow path of the Deep Western Boundary Current (DWBC) perpendicular to the lowermost margin of the Campbell Plateau and Bollons Seamount. The four major nodule facies, SHH (slope hydrogenetic nodules with high density), AHH (abyssal hydrogenetic nodules with high density), ADH (abyssal diagenetic nodules with high density), and ADL (abyssal diagenetic nodules with low density) were identified. Two additional minor nodule facies, SIB (slope irregular nodules with ice-rafted boulders) and SHB (slope hydrogenetic nodules with boulders and crust), of localized distributions are also identified.

Jan 1, 2003

By V. I. Lakshmanan

The growing concerns on process efficiency, escalating operating and capital costs along with environmental and social concerns of using conventional technology for extracting gold and titanium dioxide demand an in-depth understanding of the fundamentals and a broader understanding of the various process steps involved. This will allow development of efficient process flowsheet for product recovery and compliance with regulatory guidelines. This paper will discuss our recent developments in mineral processing and hydrometallurgical technologies to recover gold and titanium dioxide from a wide range of feed materials including ores, concentrates and tailings.

Sep 1, 2012

By J. Kuti

In room and pillar mining a large number of working points are arranged to follow a mining pattern. Geological and roof control problems can be overcome or their effect minimized by varying this pattern. Longwall mining on the other hand, fixes the mining pattern for anyone panel. This aspect of longwall mining leads to constancy, so that a well-conceived organization, ventilation, dust and roof control systems lead to daily repetition and subsequent simplicity of control. All the same, a fixed mining pattern calls for a very careful consideration and selection of design parameters. (Ref. 1.)

Jan 1, 1971

By E. H. Denny

The subject of haulage and heisting hazards is one that merits the attention of everyone engaged in mining. The purpose of this circular is to the importance of such hazards as are shown by Bureau of Mines accident figures, to give some examples of recent accidents and briefly analyze the immediate contributing causes, and to discuss some general means found by metal- and coal-mining companies to minimize those hazards. Haulage and hoisting accidents collectively constitute the second most common cause of accidents in and about coal mines and the third most common cause in and about metal mines. In both these types of mines falls of ground cause more accidents than haulage, and in metal mines falls of persons in raises and similar openings also exceed haulage accidents in number.

Jan 1, 1942

By D. -A Tremblay

Dynamic wetting spread factors and interfacial heat transfer coefficients were determined for aluminum droplets solidifying on copper substrates, The spread factors were determined from the droplet geometries while the heat transfer coefficients were obtained by solving inverse heat conduction problems, 1-D and 2-D heat transfer models are presented and the results they provided are compared, For the latter, a sensitivity analysis was also performed to determine the influence of thermophysical properties and boundary conditions. Experiments were alternatively carried out with three different gaseous atmospheres and the dynamic wetting spread factors were correlated to the interfacial heat transfer coefficients.

Jan 1, 2005

By Ernest M. Spokes

Starting in 1980, a committee of the National Research Council studied the question of why some underground coal mines are safer than others and what could be done to improve the ones with poorer performance. The results indicated that safety is improved by management commitment to safety, by cooperation between labor and management on safety matters, and by quality training of employees and managers. Younger mines have higher accident frequencies, but are less likely to be killed or permanently disabled by a lost-time accident. Methods for improving safety performance are proposed.

Jan 1, 1983

By William H. Hallahan

The Friedensville zinc mine of The New Jersey Zinc Company is located about four miles south of Bethlehem, Pennsylvania in the Saucon Valley, an infolded and down faulted block of Cambro-Ordovician carbonate sediments surrounded by hills of pre-Cambrian gneiss and Cambrian quartzite except where breached by Saucon Creek at its entrance into the Lehigh River. The Beekmantown formation of lower Ordovician age is the host for zinc and limonite ores, the former occurring in the lower dolomitic portion thereof and the latter in the upper interbedded dolomite and limestone portion of the section. The Beekmantown is overlain unconformably by the Jacksonburg of middle Ordovician age and according to Miller (2) underlain conformably by about 2500 feet of Cambrian dolomites and 200 feet of the basal Cambrian Hardyston quartzite. Igneous rocks, younger than the Cambro-Ordovician carbonate rocks, are absent in the vicinity of the ore deposits. The major structure is a N60°E-trending saddle-shaped doubly plunging anticline overturned to the north. A syncline lies to the north of the anticline. A thrust fault of substantial displacement repeats the south limb of the anticline. The ore consists of sphalerite and pyrite, along with gangue dolomite and quartz, filling and replacing the sedimentary type matrix of a strata-bound solution collapse breccia in the dolomitic portion of the lower Beekmantown. This breccia was produced in pre-Jacksonburg time as a consequence of uplift, erosion, and development of a karst topography and subsurface drainage system in the Beekmantown. Deposits of both zinc and limonite are present on the vertical north limb, on the crest and on the gently dipping (25°) south limb of the Friedensville anticline; consequently, there is no preferred structural setting for mineralization. Rather this distribution supports the view that the folding is post-ore. Features confirming this view are the development of flow cleavage in the breccia matrix, the deformation of some of the sphalerite, and the fracturing of the pyrite mineralization therein. There is nothing to indicate that the age of mineralization is other than Ordovician and older than Taconic deformation. In the absence of intrusive igneous activity younger than the ore host, the writer suggests that submarine volcanic exhalations associated with the volcanic activity recorded in the eastern eugeosynclinal facies of the Ordovician may be the source of the metal ions.

Jan 1, 1968

By D. H. Carlson, J. H. Johnson

"The U.S. Bureau of Mines and Michigan Technological University (MTU) are collaborating to develop an apparatus for measuring diesel tailpipe emissions in underground mines. A tailpipe emissions measurement apparatus (EMA) is described that dilutes diesel exhaust and measures the concentrations of diesel particulate matter (DPM), CO, CO2, NO, and NO2 at known dilution ratios.The EMA was evaluated by side-by-side comparison of its measurements with those by laboratory grade instruments. Concentrations of CO and C02 measured by the EMA were usually within ± 14 pct of concentrations measured by laboratory-grade instruments for CO and ±20 pct for C02• EMA measured DPM concentrations were, on average, 29 pct lower than those measured by laboratory-grade instruments, with the differences being fairly consistent. The CO and C02 differences are related to the method of calculating the EMA's dilution ratio, and the difference in DPM concentrations is attributed to thermophoretic and/or condensation losses related to the EMA's unheated sample probe. Preliminary analysis of data obtained with a heated sampling probe and modifications in the sampling procedures have indicated reduced variability in DPM and in the calculated dilution ratios."

Mar 1, 1992

Objective: To continuously monitor, display, and record concentration levels of respirable coal mine dust in mines to an accuracy of ±25% with a 95% confidence level for at least 30 days without servicing.

Jul 1, 1997

By Jan Boon

"El presente texto describe el nuevo enfoque empleado en la Responsabilidad Empresarial (RSE) en la minería puesto que retoma el control de la agenda paralelo al crecimiento de poderosos ""descertificadores"" de la sociedad civil y la presión de los gobiernos y organizaciones internacionales como el OECD, las Naciones Unidas, entre otras. Además de las firmas que se especializan en RSE, muchas empresas de desarrollo organizacional y legal, así como empresas de consultoría en temas de gestión, estánincorporando un componente de RSE a los servicios que ofrecen y cada vez más y más compañías publican comunicados de RSE, protocolos de RSE. "

Jul 1, 2012

By Y. Héroux, A. Chagnon, M. M. Savard

"Résumé- Le gîte de Pb-Zn de Gays River s'accompagne d'anomalies des propriétés de la matière organique (MO) et des assemblages de minéraux d'argile (AMA). L'association entre la minéralisation, la distribution de la réflectance de la MO et des AMA suggère que ces traceurs peuvent servir à l'exploration des sulfures de métaux de base dans cette région.A l'emplacement du gîte, la réflectance varie considérablement (0,80% à 1,88%), pouvant même afficher une baisse avec l'enfouissement, ce qui est interprété comme une altération chimique de la MO. Les valeurs les plus élevées s'accompagnent localement de quelques textures en mosaïque et délimitent une anomalie thermique au centre sud de la région. Parmi les minéraux des argiles identifiés, l'illite et la chlorite sont terrigènes alors que la smectite, la kaolinite et la corrensite sont authigènes et, à l'instar de l'altération de la MO, résultent des nouveaux équilibres chimiques créés suite à la précipitation des sulfures.Abstract- The Gays River Pb-Zn ore deposit is associated with anomalies defined from the characters of the organic matter (OM) and from the clay minerals assemblages. The relationships be­ tween these anomalies and the mineralization at the mine suggest that these parameters can be used as new guides for the exploration for base-metal sulfides in this area.The vitrinite reflectance (RJ shows a wide range of values (0.8% to 1.88%) and exhibits an anomalous suppressive effect with depth of burial at the mine site, suggesting a chemical alteration of the OM. The highest R, values are associated with mosaic textures and outline a thermal anomaly at the south-center of the studied area. Among the identified clay minerals, illite and chlorite are terrigenous, whereas smectite, kaolinite and corrensite are authigenous and, like the alteration of the OM, are due to the new chemical equilibria resulting from the precipitation of the sulfides."

Jan 1, 1994

By P B. Hills

A simple algebraic method of aligning large scale underground excavations such as a crusher station or workshop or indeed any large cavern or mine layout to the optimal stress condition is outlined. The method uses the stress transformation law to determine how the component stresses vary as the stress tensor is rotated around its axis. The aim is to define the orientations at which the maximum and minimum horizontal stresses occur such that the excavation can be aligned with its long axis paralleling the trend of the maximum horizontal stress leading to the minimum potential for overstressing of the side walls. The physical environment in which the stress field is acting is unchanged. At the design location, the trend and plunge of the major principal stress is unchanged. However, the coordinate system by which the location of the stress field is described is arbitrary and the stress transformation law allows that coordinate system to be rotated to a more convenient orientation and for the component stresses to be calculated within the alterative coordinate system. The stress field is typically described in terms of normal and shear stresses aligned to a north–south, east–west, vertical, coordinate system. In this scenario, there are two orientations in the 360° horizontal plane defined by the coordinate system where the horizontal normal stresses are equal, and at 45° to those orientations, two orientations where they diverge to the maximum extent. Those orientations of maximum divergence correspond to the trend of the maximum and minimum horizontal stresses, usually designated σH and σh, and that is what the algebraic manipulation seeks to determine. This technique is a first pass assessment which relies on a knowledge of the full stress tensor. It is not a replacement for numerical modelling or detailed design, but a tool to guide planning.

Nov 29, 2022

By M. A. Rabah

This study aims to recover europium, yttrium metals, some valuable salts or oxides from the white powder (apatite) coating the inner surface of spent florescent lamps (SFLs). Pressure leaching using sulphuric/nitric acid successfully dissolved the metals of interest. Europium or yttrium metals were obtained by hydrogen reduction of their oxides. Addition of potassium thiocyanate converted the dissolved sulphates to thiocyanates. Selective separation of Eu and Y was then carried out by solvent extraction from the thiocyanate solution. The used solvent was trimethyl-benzylammonium chloride. N-trihutylphosphate in 1 M nitric acid was used to strip the metal loaded in the organic phase. Results showed that the quality of the cleaned glass tubes of the SFL met the standard requirement for the lamp manufacture. The white powder (WP) is composed of calcium sulphate 35.2%, phosphate 61.5% and oxides of europium and yttrium 1.65%wt. respectively. Autoclave digestion of the WP for 4 h at 120°C and 500 kPa in sulphuric acid/nitric acid mixture dissolved 96.4% of yttrium and 92.8% of europium. The conversion rate of sulphate to thiocyanate was favoured at low temperature. Stripping of Eu and Y from the loaded organic phase behaved in an opposite way. A metal separation factor of 9.4 was obtained. ate recovered europium and yttrium salts were selectively separated using ethyl alcohol or dilute nitric acid. Yttrium was very soluble while europium was not. Europium and yttrium metals were obtained by hydrogen gas reduction at 850°C and 1575°C respectively.

Jan 1, 2004

By José Pancrácio Ribeiro, Rafaella Bicalho da Rocha, Cláudio Henrique Ribeiro

For more than five years, GAUSTEC, along with large Mineral Industry companies, has sought solutions to concentrate flotation tailings and fines by using High Intensity Magnetic Separators (WHIMS). In 2014, GAUSTEC launches the world's largest magnetic separator, the GHX 1400, with capacity up to 1400t/h. By 2015, it launches NoBLOCK® technology, a protection for magnetic separators against clogging. Finally in 2017, it launches two technologies that, together with the previous two, revolutionize the market for magnetic separation, the BigFLUX® Matrix and SuperWHIMS® technology. This article aims to show all these technologies together and to show the efficiency of the same ones already employed in mining companies.

Oct 3, 2019

By Harry W. Campbell

In 1984 and 1985, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied part of the Meadow Valley Range Wilderness Study Area (NV-050-156) in order to evaluate its identified mineral resources. The study area is located in Clark and Lincoln Counties, NV, about 50 miles northeast of Las Vegas, NV. The Johnston and Fitchett prospect, in the northern part of the study area, has more than 3 million tons of marginal perlite reserves suitable for many commercial uses. A preliminary mining feasibility estimate suggests perlite could be profitably mined from the study area; however, it is unlikely these perlite deposits will be developed in the foreseeable future because of unfavorable market conditions. Zeolite minerals occur in alteration zones adjacent to perlite deposits at the Johnston and Fitchett prospect, but high quality material is closer to potential markets. A metalliferous black shale unit containing 800,000 tons of subeconomic resources may extend into the study area at the Bradshaw vanadium prospect on the northwest boundary. Limestone, stone, sand, and gravel occurrences are wide-spread, but other suitable deposits in the region are more accessible to potential markets. Seven prospects in and near the study area were examined. The entire study area is leased for oil and gas exploration. A group of perlite placer claims covering more than 480 acres was located in the 1940's in the northern part of the study area. A small group of lode claims was located in the mid 1950's in the southwest part of the study area. No mining claims are currently (1985) held inside the study area. No mineral production is known from within the study area.

Jan 1, 1987

By Franz Ramstorfer

No lingotamento contínuo, o molde de cobre, onde ocorre a solidificação primária, é um dos componentes principais que determinam a estabilidade do processo e a qualidade superficial das placas. Durante as últimas décadas, vários formatos das placas estreitas do molde foram desenvolvidos para reduzir a ocorrência de trincas transversais nos cantos das placas, de modo a melhorar a qualidade e o rendimento do produto final laminado. Placas estreitas do molde com um chanfro foram aplicadas com sucesso à produção na Máquina de Lingotamento 4 da Usiminas / Cubatão. Aspectos do desenho das placas de molde e da aplicação prática delas, bem como o impacto da aplicação na qualidade do produto final laminado são abordados. A inspeção visual dos produtos laminados após a linha de decapagem mostrou que a ocorrência de defeitos de superfície nas bordas pode ser reduzida significativamente com a utilização da geometria de molde chanfrada.

Aug 16, 2017

By Reinhardt Thiessen

This paper presents only the highlights of previous research on the paleobotany of coal. The accumulated material has become so vast that a comprehensive review of all findings relating to paleobotany would be far too long. The fact that coal is derived from plants is now so well-known that no further comment is required, but knowledge of the mode of transformation of plant substances into coal is not so general. The plant matter goes first through processes of semirottins-, maceration, and elimination of certain material to form peat, which is then further transformed into coal. The first stage has been termed the "biochemical process," because the more important changes take place under the influence of micro-organisms. Near the end of the biochemical action an unconsolidated peat is formed. The second or "dynamochemical process," caused by the addition of superincumbent rock strata such as sandstones and shales and application of additional pressure and possibly heat through mountain-building forces, results in the formation of higher-rank coals ranging from brown coal to anthracite. These stages in trans-formation of plant material to coal have been described in previous reports.4 The main object of this paper is to bring to the notice of paleobotanists the fact that coal contains an enormous amount of material in a remarkably good state of preservation. Although some of the coal-forming matter has lost its identity, much of the original structure is retained. A large proportion of the coal, therefore, particularly of common bright coals, comprises constituents or components that invariably have retained some of the original plant structure, and many of these structures may be assigned to certain plants. The identity of these plants and of the remains forms the subject of this paper.

Jan 1, 1941