Search Documents

By Anna Carolina Cerqueira Neves

Muito se tem estudado sobre materiais alternativos, como os compósitos de matriz polimérica reforçados por fibras lignocelulósicas. Isso se justifica pelo fato das fibras naturais terem vantagens no que tange ao meio ambiente, bem como relativo baixo custo. Além disso, a fibra natural apresenta características de interface com a matriz polimérica que favorecem as propriedades mecânicas pela estrutura do compósito. Esse presente trabalho objetiva analisar as propriedades de tração de compósitos de matriz de poliéster reforçados com 10,20 e 30% em fração volumétrica de fibras de cânhamo, que foram preparados alinhando as fibras em moldes e deixando-os curar por 24 horas em temperatura ambiente. Os corpos de prova foram testados numa máquina de ensaios Instron e os resultados mostraram um aumento na tensão máxima de ruptura com o aumento da porcentagem de fibra incorporada.

Aug 17, 2017

By H. W. McQuaid, E. W. Ehn

It is usually assumed that chemical specifications are sufficient for steel to be used for case carburizing, and if the steel analyzes within the ordinary limits specified for steel for this purpose, no difficulty traceable to the steel used should be encountered in obtaining satisfactory results in the case carburizing and hardening. Much work has been done to determine the effect of various alloying elements on the rate of carbon penetration, etc. but, to our knowledge, little if anything has been published in regard to the effeet of the quality of the steel on the final results in the hardening of case-carburized steel parts. The writers believe that the structure of the case both before and after quenching is greatly affected by the actual condition of the steel itself as made, and that for good results in the case-carburizing and hardening departments, the steel should be of the best possible quality as regards non-metallic impurities. It is the purpose of this paper to prove that the presence of excess dissolved oxides in the steel, as made in the melting furnace, affects permanently the results obtained in carburizing and hardening and that it is possible that the presence of dissolved oxide call result in total unfit-ness of low-carbon steel for case hardening purposes. When races and rolls for roller bearings are made from a low-carbon steel, case carburized and hardened, it is of primary importance that the results of this treatment be of the highest quality. It is necessary, therefore, that in the case-carburizing work each detail be rigorously checked to avoid any defects which would cause the loss of much time and material. The case carburizing with which this paper deals was done in under-fired oil furnaces. The temperature of each furnace is controlled by means of a platinum platinum-rhodium thermocouple, in connection with a potentiometer indicator and potentiometer recorder. The temperature of each furnace is registered every 15 min. by an operator, who is continually checked by the automatic recorders.

Jan 1, 1922

By H. W. McQuaid, E. W. Ehn

It is usually assumed that chemical specifications are sufficient for steel to be used for case carburizing, and if the steel analyzes within the ordinary limits specified for steel for this purpose, no difficulty traceable to the steel used should be encountered in obtaining satisfactory results in the case carburizing and hardening. Much work has been done to determine the effect of various alloying elements on the rate of carbon penetration, etc. but, to our knowledge, little if anything has been published in regard to the effeet of the quality of the steel on the final results in the hardening of case-carburized steel parts. The writers believe that the structure of the case both before and after quenching is greatly affected by the actual condition of the steel itself as made, and that for good results in the case-carburizing and hardening departments, the steel should be of the best possible quality as regards non-metallic impurities. It is the purpose of this paper to prove that the presence of excess dissolved oxides in the steel, as made in the melting furnace, affects permanently the results obtained in carburizing and hardening and that it is possible that the presence of dissolved oxide call result in total unfit-ness of low-carbon steel for case hardening purposes. When races and rolls for roller bearings are made from a low-carbon steel, case carburized and hardened, it is of primary importance that the results of this treatment be of the highest quality. It is necessary, therefore, that in the case-carburizing work each detail be rigorously checked to avoid any defects which would cause the loss of much time and material. The case carburizing with which this paper deals was done in under-fired oil furnaces. The temperature of each furnace is controlled by means of a platinum platinum-rhodium thermocouple, in connection with a potentiometer indicator and potentiometer recorder. The temperature of each furnace is registered every 15 min. by an operator, who is continually checked by the automatic recorders.

Jan 1, 1922

By Maurício Gammertt Röhnelt

A pesquisa em questão trata-se do aproveitamento e aplicação da escória de aciaria elétrica, um subproduto residual do processo de refino do aço. A força propulsora para realização deste projeto está associada à utilização do resíduo: a quantidade gerada é maior que a quantidade aproveitada, uma vez que este subproduto tem como limitante de uso o fenômeno de expansão volumétrica que compromete obras de engenharia. No presente estudo, a escória foi micronizada, caracterizada e incorporada em uma matriz polimérica para obtenção de um novo produto com propriedades vedantes. Os artefatos produzidos foram submetidos a vários ensaios mecânicos, químicos e de caracterização conforme requisitado pela norma NBR 15750. Após a análise dos resultados, concluiuse que os compostos constituídos pelo resíduo apresentaram melhores propriedades vedantes que o grupo controle de referência. Além disso, verificaram-se melhores condições de processamento nos compostos com escória de aciaria micronizada. Obteve-se, portanto, um produto ecológico, mais viável economicamente, com propriedades que atendem a uma especificação. Dessa forma, difundiu-se a aplicação do resíduo para outros ramos industriais, agregando a este maior valor comercial, promovendo assim a sustentabilidade por meio da substituição de matérias-primas provenientes de recursos não renováveis pela escória de aciaria elétrica.

Aug 17, 2017

By See G. T

Bentonites and fuller's earths from seven localities in N.S.W. have been analysed with respect to occurrence, mineralogy and physical properties and areas for future prospecting have been indicated.INTRODUCTIONThe rapid expansion of Australian industry in the postwar years has been accompanied by an ever increasing demand for fuller's earth and bentonite, but in New South Wales at least the demand has been met principally by imports. However, some local and generally inferior active earths have been won to blend with imported materials to reduce costs. The important discovery of the widespread distribution of bentonite clays in the Northern Coal Measures, made recently by Grim (Booker, 1956), has givenimpetus to the further search for material comparable in quality to the imported active earths.Bentonite may be defined as a highly plastic clay, generally possessing swelling properties, composed essentially of montmorillonite and derived from the alteration of volcanic ash. Fuller's earth refers to any clay which, with or without chemical treatment, is capable of decolourizing mineral or vegetable oils and is, therefore of economic value. Montmorillonite is the active component of most fuller's earths, though palygorskite-, halloysite- and even kaolinite-rich clays have been used.Previous literature related to the New South Wales deposits has been confined to general descriptions and little technical data beyond an occasional chemical analysIs have been available. Bentonites and fuller's earths from seven...

Jan 1, 1959

By Ismael Vemdrame Flores

No panorama atual da coqueificação há uma necessidade comum de aumentar o uso de carvão de menor qualidade, principalmente devido ao alto custo e decrescente disponibilidade de carvões coqueificáveis de primeira linha. Neste cenário, uma forma de melhorar a qualidade do coque é através do controle de tamanho de partículas de carvões e misturas. A granulometria dos carvões pode alterar sua petrografia e propriedades reológicas, podendo ser utilizada de forma benéfica. O presente trabalho é uma primeira parte de um estudo de longo prazo e tem como objetivo avaliar os efeitos de preparação de carvão em suas propriedades. Para esse fim, dois carvões coqueificáveis e uma mistura foram selecionadas e caracterizadas em diferentes faixas de tamanho de partícula. Os carvões e suas frações granulométricas foram caracterizadas por análise imediata, petrografia, fluidez Gieseler e índice de inchamento livre. Os resultados demonstraram que as frações granulométricas dos carvões apresentam diferentes propriedades (cinzas, matéria volátil, composição maceral, fluidez e FSI) de acordo com o tamanho de partícula estudado. Além disso, discutiu-se o motivo por trás das diferenças observadas.

Aug 1, 2018

By Ali Dehghani Ahmadabadi

Gravity separation technique is widely used in mineral beneficiation practices for its low cost, ease of operation, and eco-friendly nature. The most commonly used gravity methods for beneficiation of iron ores are shaking table, jig and spiral methods which aren't very effective for iron mineral fines. Multi-Gravity Separator (MGS) is suitable for the treatment of fines with a maximum particle size of approximately 500 µm. This study was performed on a low-grade haematite iron ore from Chadormalutailing dams. Detailed mineralogical, physical and chemical characteristics of a goethiticlateritic iron ore showed that the sample contained porous and friable oxides and hydroxides of iron. The ore sample had a feed grade of 35% Fe, 1.1% FeO, 15.5% SiO2 and 8.5% Al2O3. Haematite and goethite are the main iron-bearing minerals while quartzite and kaolinite are the major gangue mineral constituents. In this paper, the statistical evaluation and optimization of grade and recovery using a factorial design of experiment (DOE) method has been carried out for Chadormalulow grade ultra-fine haematite tailings with MGS. The input process parameters considered are drum speed, tilt angle, wash water flow rate and pulp density. The results show considerable improvements in both the quality characteristics such as grade and recovery with statistical evaluation and optimization, compared to the initial value of grade and recovery. Keywords: multi-gravity separator, mgs, statistical evaluation, optimization, haematite

Sep 1, 2012

By B. R. Benner

Progressive improvements in crusher design, screening efficiency, and operating experience along with the downsizing of many taconite operations has resulted in the abilitv of some crushing plants to produce a substantially finer product. This finer product opens the possibility of replacing the rods in the rod mill with balls as is the current practice at Sydvaranger, Norway. If this replacement could be accomplished substantial savings associated with metal wear and the elimination of rod charging may be realized. The purpose of this study was to compare the performance of a mill charged with rods with the performance of the same mill charged with balls at the pilot scale. The first objective was to establish whether we could achieve the same throughput rate at the same mesh-of-grind in a mill in which the rod media has been replaced by balls. The second point was to determine whether the ball media would create a significant tramp oversize problem.

Jan 1, 1990

By Franklin B. W. Woodbury

The Bureau of Mines, as part of its goal of helping maintain an adequate supply of minerals to meet national economic and strategic A needs, is evaluating alternative technologies to treat oxidized taconites. Since process control is an essential element in the application of these process technologies, research was performed on a prototype monitoring system utilizing a Californium-252 (252-Cf) neutron source and a thermal neutron capture-gamma ray spectra analysis method to measure the amount of iron and percent solids in process slurries. The prototype system was used to monitor the concentrate and tailing streams in a 900-lb/hr flotation pilot plant during continuous around-the-clock tests. The iron content of the process slurries was determined by measuring the total peak areas under the capture spectrum peaks at 7.626-7.632 MeV, the associated escape peaks at 7.136-7.122 and 6.626-6.612 MeV, and the iron doublets at 4.900 and 4.998 MeV. A potential method for determining the percent solids in process slurries using the 2.22 MeV hydrogen capture peak is discussed. Results of this work demonstrate a potential method for providing process control parameters using the data from thermal neutron capture-gamma ray reactions.

Jan 1, 1980

By Feng Junfa, Du Feng, Li Huamin, Syd S. Peng

"The Ordos coal field is located in the northern midwestern part of China (Fig. 1). Since the mid- 1980s, it has been developed into one of the major coal fields in the world, producing approximately 833 Mt (918 million st) of raw coal in 2013. There were once more than 400 coal mines operating in the region. However, due to the combination of market conditions and implementation of government consolidation policies, the number of coal mines operating in recent years has been reduced considerably, with increasing output.The surface of the Ordos coal field is covered with loess and alluvium layers of varying thicknesses. In many areas, their combined thickness may amount to as much as 100 m (328 ft) underlain by thin bedrock. Many loess and alluvium are aquifers receiving water from rainfalls. There are also gullies of varying depths crossing the coal field. Figure 2 is a typical stratigraphic column highlighting the coal seams and roof and floor rocks of interest.In conjunction with the development of highproductivity coal mines, numerous ground control instrumentation tests have been conducted in the operating longwall panels. Analyses of the results of those tests offer the opportunity to understand the effect of wide-ranging mining and geological factors on the overburden movement. For this reason, trips were made to coal mines of interest to interview mine management and collect their unpublished internal research reports on ground control instrumentation. In addition, literature searches on published thesis/dissertations and papers in the professional journals were performed. Finally, data from a total of 95 fully mechanized longwall panels were collected. The instrumentation involved primarily the monitoring of hydraulic pressures of longwall shields, from which the first roof weighting and first roof caving interval and periodic roof weighting and periodic roof weighting interval were identified and determined. Some panels also included measurements of roofto- floor convergence at the face, roof strata bed separation, longwall face sloughage and the height of caving and fractured zones in the overburden. Those 95 panels were located in 20 coal mines (Fig. 1) congregated along both sides of the Wulunmulun River with the following mining and geological conditions. All together those 20 mines produced more than 224 Mt (246 million st) in 2013, accounting for approximately 27 percent of the total coal production in the Ordos coal field:1. Period of mining: 1991-2013.2. Mining methods: All panels employed the one slice, full-seam natural-caving longwall mining method like those practiced in the United States. All panels were developed with a twoentry system with a single-row of chain pillars measuring 20- x 20-m (65.6- x 98.4-ft) wide.3. Coal seams (Fig. 3): Coal in Ordos coal field is high-quality steam coal, that is very low in sulfur, potassium and ash, but high in Btu. Data were collected in panels mined in a total of 10 seams with 82 panels in four seams and the remaining 13 panels in six seams. The first six seams (1-2, 2-2, 3-1, 3-2, 4-2, 5-2) were mined by the Shenhua Coal Group (the world’s largest coal company) and the #4-2, 5-2, 6R, 62, and 62R seams were mined by both the Shenhua and Yitai Coal groups. In each coal group, the sequence of mining was in descending order. For example, in Shenhua Group, the top seam 1-2 was mined first, followed by the 2-2, 3-1, 3-2, and 4-2 seam in that descending order. In Fig. 3, the top-down sequence of coal seams is listed from left to right in each coal mine group. All seams were near horizontal with dip angles less than 3°."

Jan 1, 2014

By Y. Q. Li, X. H. Long

In this work, structural and electronic properties of smithsonite (ZnCO3) and cerussite (PbCO3) as the typical lead-zinc oxide minerals is simulated by means of DFT. The calculated results could be concluded as: (1) The density of states (DOS) of Zn atom in ZnCO3 is nearer to the Fermi level than that of Pb atom in PbCO3, suggesting that the Zn atom of ZnCO3 is more active and easier to interact with water molecules and hydroxyl ions. Smithsonite, therefore, could be more readily depressed in the flotation process. (2) The bond population value of Zn-O (0.23) and C-O (0.92) in ZnCO3 is obviously larger than that of Pb-O (-0.01) and C-O (0.85) in PbCO3, indicating that the covalent characteristic of ZnCO3 is stronger than that of PbCO3. (3) It is shown that the charge of Pb (+1.32e) in PbCO3 is more positive than that of Zn (+1.22e) in ZnCO3, suggesting that cerussite is easier to interacting with HS- compared with smithsonite in the flotation process. In summary, the structural and electronic property of smithsonite is completely different with cerussite, leading to the difference of their flotation behaviour.

Jan 1, 2015

By R. E. Lindstrom

The mineral bastnasite is utilized to describe alternate processes for the extraction and separation of the rare-earth elements by solvent extraction. The rare earths can be acid-leached directly or fused with NaOH before acid leaching. Cerium, the major constituent, can be recovered by fractional precipitation, fractional leaching, or solvent extraction with tri-nbutyl phosphate. The latter process is capable of producing 99.5-percent pure CeO2 at 98+ percent recovery. Lanthanum is subsequently recovered by fractional precipitation or solvent extraction with a nitrogen-based extractant. A 20-stage mixer-settler operation with a primary amine extractant results in a 95-percent pure La203 fraction at 96 percent recovery. Europium is amenable to extraction from most of the remaining rare earths with an organophosphate extractant. Selective stripping of the europium, followed by reductive precipitation, produces high-purity Eu203. Another possibility for europium purification involves the differential extraction of europium with an amine followed by a sub- sequent reducing strip. Separation of the remaining elements is more difficult but can be accomplished with amine or quaternary ammonium extracts. Typical separation factors achieved are 3. 8 for praseodymium-neodymium and 10. 5 for neodymium-samarium.

Jan 1, 1967

By G. E. McElroy

When mechanical ventilation is to supersede the natural ventilation of a mine it is desirable to determine what resistance the mine as a whole offers to the flow of air in order to specify properly the limiting duties of a ventilating fan. The relation of pressure to volume of flow for the mine as a whole may be calculated from experimental data, or it may be determined directly by measurements of volume of flow and the natural draft pressures causing flow; but in both methods the determinations are affected by many variables. With the intention of making a practical application of both methods, a small metal mine in process of development at Butte, Mont., was selected by the writers as the object of experiments planned to compare the mine resistances determined by measurements of natural draft and volume of flow with those calculated from experimental data. Four sets of teats were made with natural draft in October, 1925, December, 1925, April, .1926, and September to December, 1926; the last set consisted of a series of weekly observations. DESCRIPTION OF MINE The mine selected for the experiments was a typical vertical shaft metal mine in the development stage. No stoping had been done, and ventilation was confined to shafts, crosscuts, drifts, and raises. Figure 1 is a dia¬grammatic sketch of the main openings. All were timbered with full sets on approximately 5-foot centers. The shaft compartments were 4 by 4.5 feet, and one in each shaft was partly blocked by staggered manway landings. A pump column in the upcast shaft was discharging about 280 gallons a minute of water at 70° F. from the 1,000-foot level. The drifts were slightly sinuous, but the crosscuts were exceptionally straight and uniform in area; both drifts and crosscuts were about 5 by 7 feet in cross section. The raises were composed of vertical sections joined by frequent 450 offsets; each had three 4.5 by 4.5-foot compartments, of which two were plank-lined ore chutes and one was partly

Jan 1, 1928

By R. F. Abernethy

Recent investigations in the United States and in other countries have produced considerable information on the nature and occurrence of minor elements in coal. The possibility of recovering certain elements, particularly germanium and uranium, from coal ash and other coal products has received considerable attention. Some flue dusts are potential sources of germanium, and certain lignite deposits are potential sources of uranium, but industrial recovery of these elements has been limited to small quantities for technical and economic reasons. Considering the large amount of coal mined annually, a small percentage of a rare element may have industrial significance if an economical method of recovery can be developed. In 1944 information on the occurrence of rare elements in coal was reviewed in Bureau of Mines Technical Paper 669 (46).3 This report is a revision of that paper with the view of summarizing published information available for United States coals, and pertinent information concerning coals of other countries. Selected references from the original paper are retained. New references do not include all preliminary reports when more permanent literature describing complete projects is available. Consequently, the list of references should not be considered complete.

Jan 1, 1963

By Hewitt Wilson

A review is given of the nomenclature, sources, imports, statistics, common methods of preparation, and testing of mineral pigments. A description of the Deer Park-Spokane colored-clay district and the laboratory methods of preparation of these colored clays, others, and siennas follows. The mineral pigments were prepared by washing or grinding the original material as received and by calcination of the yellow ocher and brown sienna with and without manganese dioxide to produce red, brown, and black colors. These prepared powders were tested for fineness, oil absorption, and color as compared with well-known brands of commercial pigments. Similar tests were made with several basalt red clays occurring in the neighborhood of Salem, Oreg., and Kalama, Eatonville, and Clay City, Wash. The color particularly was studied, since this property is the most important commercial characteristic of the minerals. PURPOSE OF INVESTIGATION Since the development of the clay industry in the Pacific Northwest, some curiosity and interest have been aroused by the red and yellow clay or ocherouslike material that has often been found associated with the commercial clay deposits. These include the red and yellow "paint pots" near Deer Park and Spokane in eastern Washington, a red clay at Clay City, another close to Eatonville in western Washington, and red basalt earths near Salem, Oreg., and along the Columbia River near Kalama, Wash. Several companies have been organized to produce pigment colors from two of these deposits but have either discontinued or never started operations.

Jan 1, 1929

By Ahmed M. Yousif, Walid M. Abdellah, Galal M. Abdel Wahab, Amal E. Mubark

The present work is concerned with selective dissolution of niobium from Gabal El Faliq concentrate sample by using fluoridefree process. The chemical analysis of concentrate sample revealed the presence of high amount of ZrO2, Nb2O5, Re2O3, and HfO2 assaying 33.6, 1.99, 4.8, and 1.2%w/w respectively. Several economic minerals including zircon, samarskite, fergusonite, and xenotimewere recorded in the studied sample. About 98%of Nb content was selectively dissolved at the optimumconditions of 1:2 concentrate sample: KOH weight ratio, 2.5 h fusion time, and fusion temperature of 550 °C. Organic solvent extraction process using Aliquat 336S in xylene was effectively used for preparing pure Nb2O5 (98.95%).

Oct 22, 2019

By M. Askari, A. Ahmadi

"This study was conducted to establish the possible application of bioleaching in the pilot scale to recover valuable metals from the sulfidic tailings of Golgohar Iron Mine (Kerman, Iran). Using bioleaching processes, solvent extraction and sulfide precipitation recovery of valuable metals including, copper, cobalt and nickel from the tailing was investigated. The results showed that the optimum pH and temperature conditions relative to the bioleaching step was 1.5 and 45°C. The extraction of the metals from the low grade polymetal resource with complex mineralogy is very important from economic, environmental and technical point of views. Moreover, the proposed method has some advantages from energy saving, tailing management and creating added value from waste materials aspects.INTRODUCTION The growing demand for base metals and strategic such as: copper, nickel and cobalt as well as high-grade resource depletion has caused them, the mining industry to extract metals from low-grade resources and driven by complex mineralogy (Xie et al., 2005). Economic extraction of metals with low grade sources requires low-cost and efficient processing methods. A source with enormous potential for metals in future, secondary sources, such as: tailings mineral industries which the lack of appropriate technology and the high cost of processing weren't recoverable with previous procedures in the past. But it is possible that with develop new and efficient technologies have the economic exploitation ability. Recovery of metals from tailings resources is very important not only in terms of precious metals but also in terms of reducing environmental problems (due to heavy metals). The metals of copper, nickel and cobalt are mainly like sulfide compounds in the nature, usually for their recovery, first they make ore with flotation method to obtain the sulfide concentrate that containing valuable metals. then for the metal production, it will be melt and purification. Due to the environmental aspects, technical problems in the recovery of base metals from low grade ore and mixes, the presence of small reserves, in the past three decades they pay much attention to the use of hydrometallurgical processes for the recovery of base metals from these resources. These processes are classified according to the solver agent to leaching sulfates, chlorides, nitrates and amines (Hackl, 1995). Early, chloride leaching under oxidation condition in acidic or alkaline solutions was recognized the best process to produce sulfide concentrates. But then the basic processes sulfates was considered as the superior process because of being easier, a better understanding of the chemistry of leaching and recovery of base metals, especially copper from the environment easier sulfate solution with an organic solvent extraction and electro winning. The bioleaching is shown its ability on a commercial scale of low-grade sulfide minerals and ore that because of environmental reasons, the possibility of melting is not possible to them. The existing industrial base factories are based on primarily on the bioleaching and pressure leaching and recovery of cathode copper sulfate solution by extraction with organic solvents (SX) and electrowinning (EW) (Wang, 2005). Preliminary analysis has shown that valuable elements such as copper, nickel and cobalt are in the float flotation unit. Hence the plan to extract these metals from the wet tailing stream has been done."

Jan 1, 2017

By Jéssica Dornelas Silva

Diferentes mecanismos podem atuar e governar a deformação plástica de uma liga metálica. Estes mecanismos são fortemente dependentes de características como composição química, estrutura cristalina e energia de falha de empilhamento. Com o objetivo de se avaliar o comportamento do aço inoxidável duplex UNS S32304 quando submetido a esforços trativos e considerando a importância desta informação durante a conformação mecânica, este trabalho estudou a influência da taxa de deformação sobre as principais propriedades mecânicas medidas no ensaio de tração. Para a realização deste estudo, corpos de prova de tração foram usinados a partir de chapas do referido aço laminado a frio com espessura final de 2,5mm. Cada conjunto de 3 corpos de prova foi submetido às taxas de deformação de 7x10-4 s-1, 7x10-3 s-1 e 4x10-2 s-1. Por meio da análise dos resultados, observou-se uma diminuição na ductilidade e um aumento no limite de escoamento com o aumento da taxa de deformação. Entretanto, o limite de resistência não variou de forma significativa nas diferentes taxas estudadas.

Aug 17, 2017

By A. C. Smith

The U.S. Bureau of Mines evaluated the effectiveness of automatic water sprinkler systems on the suppression of incipient and propagating conveyor belt fires under ventilated conditions. Large-scale experiments were performed at airflows ranging from 1.1 to 4.6 m/s. In incipient fire experiments with 100°C, standard-response sprinklers installed above and between the belts, the sprinklers activated later, the peak heat release rates were larger, and more belting was consumed at the higher airflow. In similar experiments with 74 °C, fast-response sprinklers, the sprinklers activated at the same heat release rate for both high and low airflows, but the peak heat release rate and amount of belting consumed was slightly higher at the lower airflow. In incipient fire experiments with sprinklers located only above the top belt, the heat release rate and amount of belting consumed was larger at the higher airflow. The propagating fire experiments showed that sprinklers located above and between the belts were effective in stopping flame propagation. Peak heat release rates and amount of belting consumed were larger at the higher airflows for both the 74 °C, fast-response and 100 °C, standard-response sprinklers. The sprinklers were equally effective at each airflow.

Jan 1, 2010

By D. Eugene Rannels, Sarah E. Dunsmore

"Dunsmore, Sarah E., and D. Eugene Rannels. Extracellular matrix biology in the lung. Am. J. Physiol. 270 (Lung Cell. Mol. Physiol. 14): L3-L27, 1996.-The lung and other organs are comprised of both cellular and extracellular compartments. Interaction of these components modulates physiological function at the organ, cellular, and subcellular levels. Extracellular components in the gas-exchange region of the lung include both noncellular interstitium and basement membranes. Connective tissue elements of the interstitium in part determine ventilatory function by contributions to tissue compliance and to resistance of the diffusion barrier. The basement membrane underlies cells of both the alveolar epithelium and the capillary endothelium; basement membrane components exert biological effects on adjacent cells through receptormediated interactions. This review emphasizes current knowledge concerning the composition and biological activity of extracellular matrix in the alveolar region of the lung. Matrix synthesis and turnover are also considered. Directions for future research are suggested in the context of current knowledge of the lung and other model systems. EXTRACELLULAR MATRIXEXTRACELLULAR MATRIX is a general term that encompasses components of the basement membrane and interstitial connective tissue. The extracellular matrix has many functions. It provides structural support, compartmentalizes tissues by separating epithelium or endothelium from interstitium, and serves as a physical barrier. Both in vivo and in vitro studies show that extracellular matrices also affect cell shape and function. The matrix elicits a variety of cellular responses, including adhesion and spreading, changes in cytoskeletal organization and differentiation, formation of focal contacts and stress fibers, stimulation of proliferation and migration, induction of polarity and gene expression, alterations in metastatic activity, and outgrowth of cell processes (for review see Refs. 387, 462). Cellmatrix interactions play roles in embryonic development and organogenesis (for review see Refs. 1, 91), in wound healing (for review see Refs. 145, 327), iri metastasis (for review see Refs. 430, 431), and in angiogenesis (for review see Refs. 185, 186). The extracellular matrix is the subject of a large volume of literature. In 1994, over 1,000 articles contained extracellular matrix in the title or abstract. After a brief discussion of key aspects of extracellular matrix biology, this review will focus on the extracellular matrix of the lung."

Jan 1, 1998