Search Documents

By Richard E. Beane

For several decades, the minerals industry has used leaching techniques to extract metals from rocks whose grade was too low to be treated profitably using conventional metallurgical techniques, and, as of 1972, about 15% of domestic copper production was derived using leaching methods (Beall 1). Increasing interest is currently being directed toward solution mining, particularly with respect to copper, for basically two reasons. In the first place, geological exploration has outlined several copper deposits of large tonnage and 1m', grade which are buried at sufficient depth to preclude open-pit mining which would make such mineral deposits ore deposits. Nevertheless, these occurrences provide significant potential if they could be treated by chemical leaching in situ. Secondly, the porphyry deposits of the western united States, which provide by far the largest percentage of domestic copper, do not terminate geometrically with sharp borders. These large disseminated bodies commonly decrease in grade laterally away from volumes of rock containing ore grade metallization, and the distinction between ore and waste is strictly economic. In order to extract ore grade material from the ground, a significant amount of rock containing sub-ore-grade copper must also be removed which, when placed on dumps, is amenable to solution mining. These two considerations clearly indicate the reasons for the growing interest in solution , leaching techniques--namely the ability to exploit deeply buried low grade deposits and the expansion of reserves in deposits currently under production.

Jan 1, 1977

By Jim Clark

Tunnel boring machine (TBM) tunneling is an ever-increasing prospect for underground construction, and, with each new tunnel bored, there are unknown elements. When boring through the earth, even extensive geotechnical baseline reports can miss fault lines, water inflows, squeezing ground, rock bursting and other types of extreme conditions. This article draws on the consider-able field service experience within Robbins to analyze successful methods of dealing with the most challenging conditions encountered. Many tunnel projects are located in areas with relatively poor access along the tunnel alignment and bored under extremely high overburden. These two factors often result in limited geological information. It would be reason-able to state that the deeper the tunnel, the greater the lev-el of uncertainties. When faced with these uncertainties everyone involved with the project including the owner, the contractor and the machine supplier must be prepared to tackle geological surprises. This article describes the problematic geological conditions and associated difficulties faced on three separate projects and the measures that were taken to overcome these difficulties.

By M. H. Dehghanpoor, M. Zivdar, M. Torabi

"A hydrometallurgical route was developed to extract metals such as gold, silver, copper, and selenium from anode slime from Sarcheshmeh Copper Complex in Iran. For the extraction of copper by leaching, the anode slime was heated and stirred with 4 M sulphuric acid in the presence of oxygen. Optimal conditions for recovery of copper were temperature 80°C, mixing time 5 hours, and oxygen flow rate 2 L/min, resulting in a copper recovery of 94.47%. Silver and selenium were dissolved by leaching anode slime from which the copper had been removed with nitric acid. For gold extraction, anode slime was heated with aqua regia at 90°, and the gold then extracted with 2-ethyl-hexanol at a concentration of 0.5 M and phase ratio of 4. The extract was then stripped with soda solution at pH=10.5 and a phase ratio of 5. Finally, gold was recovered by precipitation with oxalic acid at a ratio of mass to volume 10 g/L. Total gold recovery was 80%. IntroductionDuring the electrorefining of copper, some metals are accumulated in the byproduct anode slime, which is an important source for recycling and recovery of these metals (Petkova, 1994). In this paper, a hydrometallurgical route is described for the recovery of precious metals from copper anode slime of Sarcheshmeh Copper Complex, which is located in southeastern Iran .Copper anode slime is black or gray powder with a particle size less than 200 mesh. Approximately 2 to 20 kg of anode slime is produced per ton of copper cathode. The slime is characterized by higher amount of Ag, Se, Pb, and Cu compared to other metals and a very low Au content (Khaleghi and Ghader, 2013).The copper anode slimes are composed of 11.69% selenium, 3.93% copper, 5.26% silver, 0.13% gold, and 45% barite, plus lead, tellurium, antimony, sulphur, and silica with small amounts of nickel, iron, zinc, and bismuth. Gold is one of the most important noble metals due to its wide applications in industry and economic importance, so recovery of gold from slime is more appealing than that of other metals. According to the World Gold Council (2013), the demand for gold has increased during the last decade. This increase is due not only to the increasing demands of the jewellery market, but also to the increasing demand for gold in industrial as well as medical applications (Ranjbar et al., 2014)."

Jan 1, 2016

By D Roldpo, M Vidigal, J F. C L Costa

The local cumulative distribution function (lcdf) of a selective mine unit (SMU) can be estimated by conditional simulations using the statistics derived from the sample points, generating multiple equally probable scenarios. Conditional simulations permit the evaluation of the lcdf at any support, taking into account the spatial variability, ie the variogram, and the two statistical moments, mean and variance, of the conditioning samples. The SMU ore losses and dilution depend on the mining method and mining equipment selectiveness that, in its turn, depends on the predicted block size. A new approach to predict ore loss and dilution was developed in this study. Monte Carlo simulation is used to randomly generate a grade value derived from the lcdf at the mining stage (Zs_mc(t)) in order to make a decision about the SMU destination, ie processing plant (ORE) or waste dump (WASTE). If Zs_mc(t) is lower or equal to the cut-off (Z_cut-off) the block is ORE and, conversely, if Zs_mc(t) is higher than the cut-off (Z_cut-off) the block is WASTE. Considering these binary destinations ORE/WASTE, at the mining time t, and combining each realisation of the simulated random function Zcs_i (X), there are four possibilities for each SMU simulated value: 1. the block was simulated as ore and is actually ore (OO), 2. the block was simulated as ore and is actually waste (OW),3. the block was simulated as waste and is actually ore (WO), and 4. the block was simulated as waste and is actually waste (WW).The dilution factor is given by possibility 3 (WO), while the ore loss factor is represented by possibility 2 (OW). These results comprise the classical classification and reconciliation plots used in the mining industry. The new procedure proposed in this paper is based on the use of all the equally probable simulations to define the ore loss and dilution factors. An application of this methodology was carried out at Vale's iron mine in Brazil. The grade of silica was simulated and 50 multiple equally probable 3D models were generated. The mean and the standard deviation of the ore tonnage (OO + WO) for the 50 realisations, was 233 Mt and 0.5 Mt, respectively. The mean grade increased for the diluted ore (OO + WO) as well as their respective coefficient of variation (CV). The CV increases from 62 per cent in the undiluted ore (OO), to 101 per cent in the ore, considering the dilution factor (OO + WO). The mean ore loss (OW) was 10 Mt and the waste tonnage dilution (WO) was 9 Mt.

Jan 1, 2009

By Michael J. Friedel

The integrity of mine structures, such as the roofs, ribs, face and supporting pillars, is difficult to assess beyond the exposed surface. To mitigate potential rockfall hazards, the U.S. Bureau of Mines is assessing the usefulness of Rayleigh wave dispersion analysis to detect damage and stress-relieved zones in mine structures. Classical surface wave dispersion modeling is utilized at both laboratory and field scales in damaged and undamaged material to assess the integrity of a mine pillar and roof. To more fully exploit Rayleigh wave propagation characteristics, derivation of a novel dispersion parameter was conducted using a convolutional model. The development of a suitable Rayleigh wave dispersion system based on insight derived from forward modeling is presented. The application of inverse modeling for damage and stress assessment in the mine environment is also discussed.

Jan 1, 2010

By K. Hennings

Noise from vibrating screens is generated in two ways: 1) Noise due to the material being processed and, 2) noise from the screen itself. Non-metallic decks had been shown previously to reduce material noise. The noise reduction and change in screening performance was quantified for six non-metallic decks using dolomite, granite and coal as the materials. The non-metallic decks were from 2 to 7 dBA quieter and from -1 to +10 percent less efficient as compared to a steel wire cloth deck of the same open area. Damping of the sidewalls and isolation of the drive mechanisms had been shown, in a development configuration, to reduce the noise of the screen itself. Tests of four prototype damping treatments gave reductions up to 4.9 dBA and the mechanism isolators gave an additional 2.1 dBA. The treatments were successfully life tested in two ways: 1) Lab tests to a simulated 25,000 hours were conducted on samples of the treatments in a corrosive salt spray to simulate coal plant wash water and, 2) the full size treatments were run on a full size screen for 5,000 hours.

Jan 1, 1980

"6.1. Mineralogical Techniques ApplicableTo the Platinum-Group Elements6.1.1. IntroductionThe named platinum-group minerals (PGM) usually occur as grains smaller than about 200 microns and, even when present as larger grains as in nuggets, these are often complex multimineral intergrowths. Therefore, the PGM must be examined by microscopic techniques and, because all named PGM are opaque, they are suitable for microscopic study by reflected light. Special techniques for concentrating PGM and preparing suitable polished sections are detailed in Chapter 5. Another characteristic of the PGM is that the majority have very high reflectance at 589 nm, i.e., over 450Jo, but they range from about 38 to 74%. In contrast, micro-indentation hardness has a wider range from - 60 to - 3,000 kg I mm, and the PGM range from brittle to malleable.The small grain-size of PGM imposes certain limitations, or complications, on the usual mineralogical determinative methods of reflectance, micro-indentation hardness and X-ray diffraction. In addition, certain combinations of elements in some PGM render electron-probe analyses difficult. The usefulness and shortcoming of these methods, as applied specifically to the PGM, are discussed in the following sections. These are not, however, meant to be exhaustive descriptions of the techniques, which are fully described in other texts.6.1.2. Micro-Indentation HardnessDetermination of the Vickers Hardness Number (VHN) is discussed in detail in recent publications, such as Bowie and Simpson (1977) and Craig and Vaughan (1981). In addition, the recommendations of the Commission on Ore Microscopy (COM) of the International Mineralogical Association (IMA) are given by Criddle (1980). The usual small grain-size of the PGM, however, precludes the widespread use of this technique and very few PGM have, in fact, had their VHN determined at the COM-recommended standard load of 100 gf (cf. Cabri, 1981b, in Chapter 7). Examination of VHN data reported in the literature reveals that the few PGM whose microindentation hardness has been measured have incomplete VHN data, measured with loads other than 100 gf (Chapter 7). The small grain-size may also result in unreliable VHN data because, even though the correct load may have been applied, a thin grain will give erroneous data due to the matrix, or the grain may even shatter or pop out of the section. On the other hand, micro-indentations may give useful qualitative diagnostic clues. Moncheite, for example, shows fractures near the indentation (Chapter 7, Plate 1). In other cases, intergrown PGM produce different-sized indentations: e.g., froodite-michenerite-gold in Cabri (1972); isoferroplatinumtulameenite in Cabri et al. (1973); michenerite-moncheite in Cabri and Laflamme (1976) and Chapter 7, Plate 1; altaitemichenerite- testibiopalladite in Hudson eta/. (1978) and Plate 1, Chapter 7."

Jan 1, 1979

RESOLUTION ADOPTED BY THE BOARD OF DIRECTORS AT ITS MEETING ON APRIL 17, 1936 Recognizing the fact that the problems of the committee named by the Board to prepare the " official ticket" for officers and Directors of the Institute are various and difficult; and desiring to assist this committee by setting forth some of the principles that should guide the committee and some of the qualifications that should be required of candidates, the following instructions are formulated and the Secretary is directed to publish them in MINING AND METALLURGY concurrently with the publication of the names of each newly appointed Nominating Committee and to send a copy to each member of the Committee. NOMINATIONS TO BE MADE Each year the Nominating Committee is to select "official" candidates for eight places, as follows: (1) President and Director (2) Vice-President and Director (3) Vice-President and Director (4) Director (5) Director (6) Director (7) Director (8) Director GEOGRAPHICAL DISTRIBUTION The Bylaws provide that "the Nominating Committee shall, so far as practicable, distribute representation on the Board geographically." Pursuant to this provision, the United States, Canada and Mexico have been divided into fifteen districts, as shown on the official map.* Districts 1, 5, 6, 10, 11, 12,13,14, and 15 are assigned one Directorship each; District 2, three Directorships; District 3, eight Directorships; District 4, two Directorships; and Districts 7, 8, and 9, two Directorships between them. It will be the duty of the Nominating Committee to make selections that will give effect to this allocation of Directorships. There is nothing to prevent a Director being named to succeed himself. Attention is called to the: fact that many Institute members now resident in New York formerly lived in the West, South, or North and still have intimate business connections that compel them to visit various parts of the country periodically. Such men are particularly valuable as Directors and their nomination and election tends to minimize the objection that a large number of Directors reside in New York.

Jan 1, 1940

By Franklin H. Persse

To meet escalating energy requirements, substantial increases in production from the strippable coal and lignite deposits in eastern Montana, western North Dakota, and northeastern Wyoming already have occurred, and further expansions are expected at least until the year 2000. Such production, attributable largely to rising demand for low-sulfur coal, must be accomplished with a minimum of adverse effects on the environment. Information on geology, climate, and current land use in the Upper Missouri River basin is presented in the Bureau of Mines review as a guideline to what operators may expect during and after mining. Proven methods of protecting the air and water from pollution and of restoring mined land for other uses are described, and untried methods of land reclamation, some with equipment yet to be manufactured, are discussed as possible means of maintaining aesthetic values in the basin. Costs incurred to protect the environment are part of the production cost and thus are borne by the ultimate consumer. Unit production costs are less for the thick coal and lignite deposits of the basin than for the thinner but higher Btu coal deposits of the Eastern and Midwestern United States. Precise comparisons of environmental protection costs between mines in such disparate areas cannot be made, because of differences in physical conditions, accounting procedures, and other variables.

Jan 1, 1975

By W. A. Gow, G. M. Ritcey, M. C. Campbell

"Uranium is a unique commodity. It is both a metal and a fuel, It has both commercial and military uses. It yields ""clean energy "" but presents environmental concerns. All of these factors have an impact on the commerce of uranium.Being a metal, uranium is extracted from ore like many other metallic minerals. As a fuel, it is subject to the vagaries of energy commodity market forces. The history of uranium in the first nuclear weapons has led to nation al governments carefully controlling production and sale of uranium. The spectre of radioactive contamination of the environment adds further to the public concern over the disposal of low-level radioactive wastes from uranium processing and use.There have been a number of excellent reviews on the commercial aspects of the uranium industry. In this discussion, these aspects will be briefly summarized to provide a general picture of the strengths of the Canadian uranium industry and the pressures to which it is being subjected currently. The principal thrust of this paper will be to outline Canada's resource strength and to identify some factors which will affect Canada's ability to continue holding a sizeable share of the world uranium market."

Jan 1, 1985

By L. S. Allen, R. L. Caldwell, W. R. Mills

Borehole models used in the study of nuclear well logging are reviewed and the merit of heterogeneous us homogeneous formation simulation is discussed. .A heterogeneous model for simulating sandstone formations of variable porosity is described. Simulation adequacy was checked by steady-state and pulsed-neutron measurements. INTRODUCTION In the course of developing new methods of nuclear well logging, the problem of testing new logging instruments under controlled conditions always arises. This testing is usually done in wells of known lithology, porosity and fluid saturation, or in laboratory test facilities which simulate the borehole environment. Although the former approach is possibly more satisfying, it is frequently difficult or inconvenient to find wells with enough variation in the cited parameters for a truly comprehensive study, On the other hand. laboratow- test facilities can simulate a wide variety of formation and borehole conditions if care is exercised to maintain adequate simulation under all conditions. Workers concerned with the development of nuclear well logging methods have reported several types of research facilities in the past. Tittle, et a1 used cubical tanks filled with Ottawa silica sand to study the steady-state behavior of thermal and epithemal neutrons in simulated sandstone logging environments.1 In addition to the effects of fresh vs salt water, a wide variety of casing sizes and compositions were investigated. Tittman also used a large tank of Ottawa sand to measure the slowing down length of sio2;2 for making the same measurement in CaCO3, however, an assembly of solid Vermont marble blocks was used. More recently a very useful and carefully planned test pit for nuclear logs was constructed under the auspices of the API.3 This facility consists of three massive limestone sections, each 6-ft thick and more than 5 ft in diameter. The blocks are buried, one on top of the other, in a concrete- lined pit having a total depth of 24 ft. Each section is made of a different limestone to achieve porosity variation, the selection being Carthage (2 per cent), Indiana (19 per cent) and Austin (26 per cent). The blocks are traversed by a 7 7/8-in. diameter borehole and are saturated with fresh water. Great care was taken to insure total saturation of the stone. Homogeneous mixtures and materials have not been used exclusively for simulating earth formations. Tittle, et a1 4 showed that a heterogeneous lattice of water and graphite could be used to simulate Liquid furfural with very little effecton measured thermal and epi thermal neutron distributions. Subsequently, a lattice-type model for simulating limestone earth formations was designed and built by Berry This limestone model was constructed of 7/8- x 11/4- x 36411. marble rods glued together with a plastic resin to form a 36-x 42- x 42in. cube. The cube was honeycombed vertically with 7/8- x 7/8- x 3641-1. holes for porosity and had a 111/2-in. diameter hole in the center to serve as the borehole. Lower porosities were simulated by placing marble rods in the square holes. The finished cube was used with the borehole vertical and set in a tank to hold liquid for filling the holes in the rock matrix. A second type of heterogeneous borehole model has been proposed by Kukharenko, et a1.6= In this concept the model is composed entirely of solid material. The hydrogen equivalent of formation fluids is simulated by making the model of alternating layers of dense rock and celluloid. Additional hydrogen is included by drilling vertical holes in the rock sections and filling them with solid forms of hydrogeneous material. The volume of the holes is equal to the volume of the celluloid layers, so an axial and radial dispersion of the hydrogeneous material is thus obtained. One such model was composed of alternate 50 mm-thick sand layers and 2 mm-thick celluloid sheets. Approximately 200 appropriately spaced plastic tubes were used in each sand section. The plastic tubes were filled with paraffin for additional hydrogen concentration. This arrangement yielded a model with a water-equivalent hydrogen concentration of 10 per cent. Experimental data taken in this model and in a model consisting of the same material but homogeneously dispersed showed that the heterogeneous system adequately

Jan 1, 1966

By A. M. Beebee

IN the present century the coal and manufactured gas industries have been eclipsed in public interest by oil, natural gas, and hydro- electric energy, which have had the benefit of rapid development and novelty. I sometimes wish that our social- order were such that hydro power had been developed first, that the use of gas from coal had never been seriously considered, and that our domestic energy requirements were supplied by other fuels. Sup- pose the manufacture of gas from coal should then come on the scene at the present time with the current plight of the railroads, coal regions, and labor generally, presenting the fact that it could increase the amount of coal mined and shipped by the railroads by some 16,000,000 tons, and increase the coal used at existing u plants five times. Imagine the great public interest that would be manifested; it would supply the cooking and water-heating requirements of a community with a superior character of service at a cost to the customer approximately half that which had obtained previously. Would not such a situation be heralded as the salvation of our country and all help be given it?

Jan 1, 1940

By A. F. Banfield

"IntroductionELEMENTAL sulphur occurs in three types of deposits: in salt domes in the Gulf Coast region of the United States and Mexico, from which over 90 per cent of world native-sulphur production is obtained; in sedimentary deposits such as those in Sicily, which are thought by some authorities to contain the largest world reserves of elemental sulphur; and as surface deposits, associated now or in the past with some phase of vulcanism, the type which bas the greatest world-wide distribution.Deposits of the volcanic type are the subject of this paper.From antiquity until the successful development of the sulphur-bearing salt domes at the beginning of this century, important sulphur production for local needs was obtained from volcanic deposits in many parts of the world. Due to technical and economic factors, however, producers could not compete in price with sulphur from salt domes. •The result has been that, except in Japan and Chile, little sulphur was produced from volcanic deposits from about 1910 until the start of the Korean war in 1950. Shortly after the outbreak of the Korean war, an acute world sulphur shortage developed and prices skyrocketed in many countries up to several hundred dollars a ton. Interest in volcanic deposits was renewed and exploitation of many was undertaken. Few of these operations have been successful, mostly due to inability of management to solve technical problems.While important volcanic deposits of elemental sulphur have not been reported ( 1) in Canada, and it is doubtful that any will be found, data presented in this paper may be of interest to students of ore genesis.This paper is based on field examination of numerous deposits of the volcanic type in North and South America."

Jan 1, 1954

By B. J. Moore

This publication contains routine analyses and related source data for 374 natural gas samples from 24 States and 5 foreign countries. These samples were collected during calendar year 1966 as a part of a continuous survey of the free world for occurrences of helium in natural gas. This survey has been conducted in the United States by the Bureau of Mines since 1917. In late 1965, the survey was expanded to include foreign gasfields. The analyses of foreign samples contained in this publication represent the first samples received as a result of this expanded program. The analyses published herein were made by mass spectrometer and a special helium analysis apparatus, which are described in Bureau of Mines Bulletins 4863 and 576.4 Eight previous publications have been made to present the results of 7,244 gas analyses made? by the Bureau of Mines Helium Activity prior to 1966. The first three, Bulletins 486,5 576,6 and 617,7 contain analyses and related

Jan 1, 1967

By C. C. Hustwit

The U.S. Bureau of Mines formulated a new mathematical model to characterize iron oxidation. The new model is intended to replace the currently used model, recommended by the Environmental Protection Agency (EPA), for most acid mine drainage (AMD) treatment applications. The new model was evaluated in a series of five synthetic AMD treatment tests. The initial ferrous iron concentrations ranged from 800 to 2,400 mg/L. In these tests, the Bureau model underpredicted the measured ferrous iron oxidation rates by a range of 3.24 to 8.03 pct. This was considered to be in close agreement after consideration of experimental error. The model proposed by the EPA was also evaluated using the same test data. The EPA model underpredicted the oxidation rates by a range of 77 to 100 pct in four tests and overpredicted by 19 pct in one test. The model formulated by the Bureau expresses that the rate of iron oxidation is a function of a treatment system's oxygen transfer efficiency and is independent of ferrous iron concentration when treated to near-neutral pH's. A new test method for evaluating oxygen transfer in flow-through reactors is also described.

Jan 1, 2010

Jan 1, 1926

By Roland J. Lapee

A history of the progress made in copper refining in Montana is presented. The casting furnaces and the newly rebuilt electrolytic refinery are descmbed and operating details are given. Experiences with various addition agents, effects of rernoval of chlorine from the electrolyte, and effects of separan on electrolyte and on copper deposit are discussed. Observatzons are made on the effect of various impurities in anode copper and behavior of thezr salts in electrolyte and in slime, on treatment of slime for removal of copper, and on electrolyte puriification problems. The improved method for production of starting sheets is described. Attention is given to new materials for construction and to improvement in matrials handling ad quality control. COPPER refining at Great Falls, Montana, dates back to 1892. The original plant produced 65,000 lb. of cathodes per day at a current density of 16 amp per sq ft. In this plant anodes and cathodes were handled to and from the cells by means of hand-operated chain blocks and were moved about the plant by hand trucks. Cathodes were melted in coal-fired, reverbera-tory furnaces, were charged by hand, and refined copper was dipped by hand and cast in iron molds. In 1916, a new, modern plant with capacity to refine 18 million Ib. copper per month was built. Two refining furnaces were built, and each was provided with a twenty-mold Clark casting wheel. In 1922, the furnaces were converted to the use of pulverized coal: in 1923, to the use of oil; and in 1928, to the use of natural gas. In 1926, the plant was enlarged 50 pct. The use of pulverized coal for refining copper at Great Falls was discussed1 in a paper presented at the Salt Lake City meeting of the Institute in September 1925. Also, a comparison of the use of various fuels in copper refining furnaces was discussed 2 in a paper presented at the New York meeting of the Institute in February 1932. Prior to 1943 the cellroom was operated with twenty-five 720-lb. anodes and 26 cathodes per cell. Four cathodes, each weighing about 165 lb., were produced from an anode. In 1943 the weight of the anode was reduced to 460 lb., and two cathodes, each weighing about 190 lb., were produced from an anode. In 1949, a Billet Casting Wheel for the production of 3 in. diam phosphor deoxidized billets was built. A paper, presented at the New York Meeting of the Institute in February 1956, describes3 this plant and operation. In the electrolytic refinery, production is controlled by variation of the current density. In 1956, germanium rectifiers on a separate electrical circuit were provided for the starting sheet section so that current density could be maintained at any desired figure. Also in 1956, a program of modernization and enlargement of the Electrolytic Copper Refinery was started. This program, when completed, will raise the capacity of the Great Falls Electrolytic Copper Refinery approximately 33 pct, to 33 million lb. of cathodes per month. Furnace capacity for melting cathodes and anode scrap is ample to take care of the increased production from the electrolytic refinery. This fortunate condition came about primarily as the result of the three following changes: 1) The furnaces were lengthened 10 ft in 1922 when the fireboxes were found unnecessary for burning powdered coal. 2) Furnace life, and hence furnace capacity, was increased by the successful efforts of the Copper Refinery staff to develop a method for sanding furnace side walls and roof. 3) The natural gas being used has a very low sulfur content. As a result, it is possible to reduce time spent rabbling and poling and thus greatly increase tons per furnace charge. TANKHOUSE AND TANKS The Great Falls Electrolytic Refinery is 535 ft long by 252 ft wide. The cells are arranged in four crane bays in which are operated seven 10 ton Whiting Cranes. The old cells are in groups of ten, with circulation of electrolyte through five cells in cascade and with aisles between the groups of ten cells. The new cells are nested in groups of sixteen with no aisles, are all on one level, and have individual circulation to each cell. Present plans call for 1792 commercial cells and 128 stripper cells. To reduce confusion during the construction period, and to use the cranes, cars, and other equipment already on hand, the cells in the rebuilt section were designed to have approximately the same inside dimensions as the cells in the old part of the

Jan 1, 1962

By Ralph H. Whaite

To assist the anthracite industry obtain technical data on pneumatic packing, the Federal Bureau of Mines imported a pneumatic packing machine from Germany and installed it in a mine of a cooperating company in the Northern anthracite field of Pennsylvania. This report covers the second in a series of experiments in applying pneumatic packing for controlling strata movement (subsidence) above mine workings in the Pennsylvania anthracite region. The first experiment2/ was begun in January 1950, in a section of the mine where about 50 percent of the original coal remained in the form of pillars; since the company did not plan to mine the pillars in this particular area, pneumatic packing of the chamber voids was done for test purposes only. During this initial test the machine was operated on 204 shifts, and 652,400 cubic feet of breaker refuse material (22,834 tons) was packed into the voids of 16 chambers. The work was completed in December 1951.

Jan 1, 1956

By D. S. Choi

The paper presents the result of analysis of subsidence data collected from coal mines operating in Northern West Virginia and Southwestern Pennsylvania. A particular emphasis la placed on the measurement of the angle of draw for the protection of surface structures.

Jan 1, 1986

By Walter W. Kaufman

This User's Manual, extracted from information contained in the Final Report for the above referenced project, outlines test procedures to measure the braking capabilities of underground non-coal rubber-tired mining equipment. Methods to interpret test results, recommendations for safe braking capabilities, and basic techniques to improve braking systems and road surfaces are also discussed. Possible applications for runaway vehicle protective devices other than braking systems are reviewed. Also included is a listing of mining equipment and brake component manufacturers who supply the majority of equipment to the United States non-coal mining industry. In conjunction with this list of manufacturers, a general tabulation of brake related specifications appears for vehicles observed during stopping tests conducted underground.

Jan 1, 1977