Search Documents

By W. E. Pittman

The Bureau of Mines, as part of its Health and Safety Technology Program, is conducting research on the use of ground penetrating radar (GPR) for mine hazard detection. GPR offers a possibility of mapping immediate below-surface geologic conditions, including faulting and other anomalies, thereby exposing potential safety hazards to miners. This report summarizes a literature review of the current status of GPR research in and outside the Bureau.

Jan 1, 1984

By W. K. Tolley

The Bureau of Mines is testing super critical fluids as solvents to selectively extract valuable components from complex matrices. Materials recovered during supercritical fluid extraction are often highly purified. Using laboratory apparatus designed specifically for supercritical fluid research, Bureau re-searchers have measured the solubility of titanium tetrachloride (TiCI4) in supercritical, liquid, and gaseous carbon dioxide (C02), CO2, a commonly used supercritical fluid, is inert, inexpensive, and nontoxic. Supercritical CO2 formed a single phase with TiCl4 at 45° C and 1,500 psig. When the solution was heated at constant pressure beyond 55° C, TiCl4 precipitated from the fluid. Results showed that TiCl4 solubility in supercritical CO2 is not controlled by the vapor pressure of the solute.

Jan 1, 1989

By E. R. Palowitch

This report is the result of a series of coal-cleaning tests using a dense-medium cone-type washer. Detailed results are given for 2 tests using a magnetite medium and 4 tests using a pulverized-refuse medium. Approximately 120 float-and-sink tests and over 500 separate chemical analyses were made in conjunction with these tests. In these tests higher recovery efficiencies and sharper separations were obtained when using a magnetite medium, especially on coal sizes below one-half inch. When sizes above 1 inch at low specific gravities of separation are cleaned, the pulverized refuse medium compared favorably with the magnetite medium.

Jan 1, 1956

By J. W. Meier

Introduction The great importance of air warfare during World War II and the introduction of large-scale air transportation and airborne operations created an immediate demand for large quantities of high quality light alloy products. Before this war, the use of magnesium, the lightest structural metal, was barely in the development stage, and considerable research work was needed to overcome difficulties in improving its properties and to attain uniform quality in mass production of magnesium alloy products. The Canadian Bureau of Mines was frequently called upon, by various agencies of the Armed Forces and of the newly established war industries, to examine magnesium alloys that had failed in fabrication or in actual service, and to advise on proper alloys and fabrication methods to be used. Failures in magnesium alloy castings were connected mainly with lack of knowledge of proper founding and surface-protecting techniques. Most of the defects were due to microporosity and faulty heat treatment. To aid the foundry industry, small-scale investigations were started on the effect of various factors in the casting technique in order to improve the quality of the products. These investigations were made in co-operation with representatives of the Armed Forces and the Canadian magnesium industry. This work was later co-ordinated into a broad research programme on magnesium alloys, comprising problems on melting, refining, various casting methods, heat treatment, and testing of properties of standard and special alloys. This research programme? is still in force, and the present paper contains some results of the first series of investigations on magnesium casting alloys carried out at the Experimental Foundry of the Bureau of Mines.

Jan 1, 1948

By J. D. Doherty

That America's great coal deposits eventually will be our principal source of liquid as well as solid fuels is generally accepted. Moreover, the day when synthetic oil from coal will begin to supplement our petroleum supplies does not appear to be far off. The American petroleum industry has not spared effort or expenditure in its attempt to keep pace with the demand for oil, and recent production has exceeded expectations. However, the rapidly rising demand for liquid fuels plus the increasing difficulty of finding and developing the new oil needed even to maintain present production rates make it highly unlikely that oil from domestic wells can fully meet future oil requirements. Therefore, it appears that one or more of the following courses must be followed: 1. Curtail oil consumption. 2. Increase imports. 3. Develop new sources such as synthetic liquid fuels.

Jan 1, 1949

By AIME AIME

NEARLY two hundred 'engineers attended the dinner given at the Hotel Pennsylvania on Monday-evening, Oct. 10, to the delegation from the American l3nginiering Societies to Great Britain and France when the John Fritz Medal was presented to Sir Robert Hadfield and to Eugene Schneider. Representatives of the British and French Governments ' and of foreign engineering societies gave to the event an international aspect unique in gatherings of engineers. Messages from men distinguished in science, statesmanship and diplomacy were read. Medals struck by the French Government were presented to the general chairman of the deputation, to the chairman of each' individual delegation and to the president's of the four Founder Societies. The meeting was regarded by engineers as formally ushering in a definite movement for world unity in the engineering profession. J. Vipond Davies, president of the United Engineering Society, acted as toastmaster. The speakers ,were Ambrose Swasey, Charles F. Rand, F. B. Jewett, A. S. Dwight, John R. Freeman, all members of the deputa- tion; and M. Gaston Liebert, French Consul General; Captain G. H. Armstrong, British Counsel General; G. G. Clapperton, representing the British Institution bf Electrical Engineers, and Prof. Jacques Cavalier, spokesman for the French universities. Among the engineers from other cities was Governor. James Hartness of Vermont.

Jan 1, 1921

By Robert D. Saltsman

The inadequacy of our knowledge of the coal combustion process has long been recognized. This was expressed very well by Spicer and Finney (1). "The control of combustion processes in industry and the design of the equipment necessary for efficient burning to take place have always been very much branches of an industrial art rather than of an exact science. This has been especially true of the utilization of coal, a substance so hetrogeneous and complex in character that all too little is known about its chemical and physical composition.' During the past several years one branch of coal utilization, that of high temperature carbonization; has made significant advances from being an art into being an exact science. This has been accomplished by the development of petrographic techniques for identifying, measuring, and determining the thermal properties of the organic materials which affect the carbonization of coal and the correlation of this information with a pre-existing standard of coke quality, the stability index.

Jan 1, 1964

Introduction The NIOSH Office of Mining and Construction Safety and Health Research has redesigned its Mining Safety and Health Web topic page. The updated page incorporates a significant amount of new safety and health information, plus an improved layout to better serve stakeholder needs. It also provides back-ground information about the NIOSH Mining Research Program, including research awards, core competencies, unique labs, community and educational outreach, and a brief discussion of how the research program is structured. The new Web topic page can be found at www.cdc.gov/niosh/mining. "Search" Feature The redesigned Web topic page features improved search capabilities. The "Search Mining" feature on each page lets you search only the NIOSH Mining Safety and Health Web topic page. The user can still search the entire NIOSH Web page by using the "Search NIOSH" option. New Safety and Health Topics Developers expanded the "Safety and Health Topics" and reorganized the site to make it easier to find information. Each topic link now has a significant amount of new and updated information, as well as links to related topics of interest. Safety and health topics include dusts, diesel exhaust, hearing loss, contact with electric current, fires, explosives, ventilation, emergency management, new and older workers, and education and training. All topics can be accessed from the home page (Figure 1). Publications Although the Web topic page highlights many of the most requested publications on the safety and health topic links, you can find a complete list of downloadable publications as well. More than 600 mine safety and health publications are now downloadable from the page. Short summaries let the user quickly identify publications of interest. Products The updated Web topic page offers more than 120 NIOSH mine safety and health products, including training exercises, toolbox talks, videos, computer software, guides, and checklists, many of which are downloadable. If not, instructions are given on how to obtain copies. Some of our products include: • Software to analyze horizontal stress, design pillars for longwall mines, and select roof bolts for ground control. • Educational software including the Hearing Loss Simulator, which simulates the effects of noise and aging; and Coal Country, which teaches children about coal formation, mining techniques, and everyday uses of coal. • Utility software including the HazCom Helper software to assist individuals in writing a HazCOM plan, as required by the Mine Safety and Health Administration (MSHA), to track hazardous chemicals at their mine sites. • Guides for troubleshooting roof support systems, under-ground workstation design, and seating design. • Training exercises and videos that can be used for safety training. Data and Statistics General mining statistics are used by a wide variety of stakeholders. The NIOSH Mining Web topic page offers statistical graphs, tables, maps, fact sheets, and other publications that document the mining population, injuries, fatalities, diseases, and occupational exposures for all mining commodities. If users prefer to analyze data themselves, downloadable files of MSHA data are available. These cover employment, production, injuries, fatalities, and accident data from 1983 to the present and are available in both SPSS® and dBASE® formats.

Jan 11, 2005

By Lloyd H. Banning

With the ever-increasing demand for energy in all forms, electrical energy generated from geothermal resources could become an important energy source in the next few decades. Geothermal fluids, which contain appreciable quantities of dissolved salts and gases, are generally corrosive to materials of construction. Since data on corrosion of materials in geothermal brines is limited, the literature was surveyed through February 1972 to obtain a compilation of information on corrosion resistance of aluminum and its alloys, copper and copper-base alloys, carbon steel and cast iron, stainless steels, chromium-iron alloys, nickel-and cobalt-base alloys, and titanium in heated brines including sea water.

Jan 1, 1973

By R. H. Schutz

TO ASSIST users in the selection of reliable and satisfactory respiratory protective devices, the Bureau of Mines bas established five schedules of minimum performance requirements for the approval of respirators. The current revisions of these schedules3 include 13D for self-contained breathing apparatus, 141F for gas masks, 19B and the amendments to 19B for supplied- air respirators, 21B for dust, fume, and mist respirators, and 23B for chemical cartridge respirators. Copies of these schedules may be obtained from the Bureau of Mines, Publications Distribution Section, 4800 Forbes Avenue, Pittsburgh, Pa., 15213. Approval tests on respirators are performed only at the request of the manufacturer4 of the respirator and at his expense. If the device meets the approval requirements, a certificate of approval is granted on the complete respirator. This certificate states that as long as the respirator is manufactured as originally approved, or in accordance with any changes covered by an extension of the original approval, the manufacturer may advertise and sell his respirator as being approved by the Bureau of Mines. Many industries and regulatory agencies require that respirators approved by the Bureau of Mines he used where respiratory protection is needed. The Bureau of Mines, however, has no regulatory power over the use of the respirators that it approves. It acts as an impartial testing agency to insure the availability of suitable and safe respirators.

Jan 1, 1966

By Sumit Kumar Hota, Asadi Srinivasa Reddy, Ashok Kumar, Ashish Agrawal, Surajit Sinha, Chandra Sekhar, Tanay Ray

In the current operational facility, due to the absence of pellet pot facility, a novel technique is developed wherein the pellets with different chemistries prepared in the laboratory are fired in an induration machine by placing them inside the Inconel baskets. In the present work, an attempt is made to optimize the pellet chemistry by developing 2 different flux pellets, viz., low basicity (B2: CaO/ SiO2 = 0.3) pellets and high basicity (B2 = 0.9) pellets, and further the effects of basicity on pellet properties, viz., cold compressive strength, porosity, swelling index, reducibility index, and softening and melting temperature, are studied. It has been found through the multiple operational trials that increasing the basicity of pellets from 0.3 to 0.9 results into improving the pellet strength, reducibility and softening and melting characteristics. Moreover, it is observed that the swelling index of pellets is reduced by adding 2% MgO to both low and high basicity pellets that could be attributed to the formation of high melting point slag in pellets. The operational trial has resulted into producing pellets that exhibit a combination of desired mechanical strength, improved swelling, and reducibility index and possess better softening–melting behavior among all the chemistries studied.

May 24, 2022

By Ricardo dos Santos Oliveira

Devido ao grande aumento da concentração de gases do efeito estufa, a criação de uma energia limpa tem sido um desafio para a ciência e as indústrias. Após identificar possíveis soluções para este problema uma alternativa seria a utilização de biomassa vegetal com capacidade térmica como fonte energética redutora no processo de redução do minério de ferro em altos-fornos. Este trabalho teve como objetivo utilizar capim elefante (Pennisetum purpureum) e carvão mineral na injeção de finos pulverizados pelas ventaneiras de altos-fornos nas siderúrgicas a fim de reduzir custos da produção de ferro gusa e reduzir a dependência de combustíveis fósseis no processo. O capim elefante é uma fonte renovável e de rápido crescimento que através da fotossíntese captura o CO2 da atmosfera, reduzindo a poluição causada pelos altos-fornos. Para simular a injeção dos materiais estudados foi construído na Escola de Minas - UFOP um modelo de partículas de combustão para analisar as amostras. Outras técnicas são utilizadas para caracterização como combustão, calorimetria, análise de gás, análise química imediata e elementar. Assim, em teoria, esta pesquisa mostra que o capim elefante misturado com carvão mineral através de sua injeção em altos-fornos mostrou-se viável em termos metalúrgicos e ambientais.

Aug 17, 2017

By T. M. Garland

This report presents a more extensive perspective of the calculated profitability of developing and producing crude oil and associated natural gas by primary methods from selected onshore areas of the United States. Estimates were made for cost of drilling, completing, equipping, and producing oil wells at four depths in seven onshore producing areas. A computer program was developed for calculating the discounted cash flow rate of return for the 64 different models in each area resulting from varying the oil-producing rate and production decline rate. The results of these calculations provide data that vividly illustrate the change in rate of return to changes in well depth, initial producing rate, and production decline rate, as well as to variations in development cost and operating expense. Cost per barrel of oil produced in terms of annual cost and total cost is also discussed. Included in the report are explanations of the method of determining costs and the procedure used for profitability analysis. Summaries of all cost estimates and results of profitability analyses are presented in the appendix in tabular form for each of the seven producing areas.

Jan 1, 1972

By Curt D. Edgerton

This study was made to determine trends in fresh water usage by California petroleum refineries, to forecast fresh water requirements to 1975, and to evaluate water conservation practices. Statistical data used in the study were obtained largely from published sources and from records of selected companies. An adequate sampling of the State's refining capacity was obtained, and the data were extrapolated to the total California refining capacity. A breakdown of the data was then made on the basis of the following refining regions: (1) the Los Angeles Basin and Southern Coastal region, (2) the Southern San Joaquin Valley, and (3) the San Francisco Bay area. An unpublished forecast of crude oil input to refineries by a major oil company operating on the West Coast was used as a basis for predicting fresh-water usage. The 1963 fresh water intake by California petroleum refineries was 84 million gallons per day. This is expected to increase to 128 million gallons per day by 1975. The fresh-water to crude-oil ratio is increasing in all regions except the Southern San Joaquin Valley. At present, the supply of fresh water available to almost all of the State's petroleum refineries, mostly from surface sources and company-owned wells, is adequate, although shortages may develop within the foreseeable future. Present conservation methods are centered around the following four objectives: (1) minimum intake of fresh water of the lowest possible quality commensurate with sound technologic practice; (2) optimum recirculation; (3) proper treatment before discharge; and (4) substitution of air cooling for water cooling.

Jan 1, 1965

By George R. Huebner

The White Pine Copper Company, subsidiary of Copper Range Company, is located in the Upper Peninsula of Michigan. The offices, plant, and mine are six miles south of Lake Superior in Ontonagon County. Employing 1700 people, White Pine is the largest single industry in the Upper Peninsula. 970 underground employees produce 16, 700, tons of ore daily. From this tonnage 363,400 pounds of refined Lake Copper are produced in various shapes as specified by the customer. The following paper explains the geology of the ore body and briefly outlines present mining methods. It enumerates the reasons for considering longwall mining of a hardrock* ore body and the preliminary investigations leading to the decision to undertake the initial test panel. Selection of the initial test panel location is covered in detail. Equipment choice and reasons for that choice are described as well as selection and training of personnel.

Jan 1, 1964

By MAURICE SUNKPAL, Taghi Sherizadeh, Kutay E. Karadeniz, Dogukan Guner, Samuel Nowak

Despite numerous empirical, numerical, and hybrid studies conducted on the subject of coal rib failure, mine fatalities related to rib failures continue to occur at around 1.5 per year between 2009 and 2021. To date, a standard methodology for the design of coal rib supports that can accommodate the wide range of unique conditions found in coal mines in the USA has not been developed, forcing mine operators to rely on the trial-and-error process or industrial legacy practices for the design of coal rib support patterns. In this study, to better understand the support systems’ effectiveness, various rib bolting scenarios were investigated. A coal mass constitutive model is implemented to a distinct element method (DEM) code, and rib factor-of-safety (RibFOS) analyses were performed by applying strength-reduction for the coal matrix and explicitly modeled face cleats. Ribs with various overburden depths and mining heights composed of solid Banded-Bright coal (BBC) were considered in this study. Different scenarios such as rib bolt length and the number of bolts were studied to quantify the effect of primary rib support density on rib stability. As a result of the unsupported coal rib analyses, a decaying exponential relationship is proposed between the mining height-overburden depth and the RibFOS. The developed coal rib models clearly show the coal-rib bolt interaction and illustrate how the addition of rib bolts restricts the movement of the coal rib. The results reveal that the strength reduction method in DEM code with the coal-mass model can aid in the development of practical primary support charts, which can help in the rib support design process. In addition, an unsupported RibFOS cutoff is proposed, beyond which the addition of primary support cannot stabilize the failed rib structure.

Aug 5, 2023

By T. A. Ring

The bed filtration of colloidal particles has been modeled by performing a differential particle balance. The balance considered the localized particle deposition rate to be the sum of three rate resistances: 1) mass transfer to a region near the surface; 2) adhesion onto a partially filled surface; and 3) resuspension from a partially filled surface. The differential particle balance equations, one for the free particles and one for the adhered particles, were solved by a finite difference algorithm. The results of this model are compared to experimental filter breakthrough curves.

Jan 1, 1983

By LEE H. CORNELL

Drilling activity in Kansas during 1945 continued at an accelerated pace to meet the demands of war; 1810 tests were drilled as compared with 1856 tests the previous year, 1771 tests in 1943, and 1516 tests in 1942. During the year 31 new oil pools and 10 new gas pools were discovered. Of a total of 364 wildcats drilled, 323 were dry; and of 1446 tests drilled in pools, 825 were oil wells, 197 gas wells, and 425 dry holes.

Jan 1, 1946

By E. Farrokh

CSM and NTNU models are among the most commonly used models in TBM performance evaluation. Due to increasing application of TBM in different tunneling conditions, modification became necessary for these models. Sensitivity analyses on these two models indicate that both models are very sensitive to machine characteristics. Analyses performed on CSM database for cutter load and penetration rate prediction indicate while the r-square of the CSM model is reasonably high for the predicted cutterload, the r-square value for the penetration is low. In order to increase prediction capability of CSM model for penetration rate the model was reevaluated using non-dimensional analysis and the original database of Colorado school of mines. NTNU model is evaluated using Monte Carlo simulation and regression analysis. The results of analyses indicate that the majority of the variation of the penetration in NTNU model can be explained by only three parameters. This might indicate that the effects of other factors are overshadowed and it is worthy to reevaluate NTNU model using original database and more updated statistical methods to avoid overlapping of different parameters correlations.

Feb 23, 2014

By E. W. Bauman

The important role that mineral aggregates assume today in the construction and chemical industries is best attested to by the astronomical tonnage figures for the annual production of aggregates in the United States as reported by the U. S. Bureau of Mines in their "Minerals Yearbook." For 1965, latest publication available, the tabulation shows a total of 1,716,000,000 tons made up of 30,000,000 slag, 908,000,000 sand and gravel, and 778,000,000 crushed stone. A much more favorable statistical position for slag can be established by listing the world-wide tonnage. According to Dr. A, W. Lee, Director, British Slag Federation, in a paper presented before the 8th Annual conference of the British Institute of Works and Highway Superintendents, he estimates that the probable world consumption of slag is in the order of 100,000,000 tons showing--Great Britain with 10,000,000 tons, Germany, 15,000,000 tons, France, 1$000,000 tons and the United States with 30,000,000 tons. Thus it is seen that the United States accounts for almost one-third of the world's consumption of slag and the 3 west European powers another third.

Jan 1, 1967