Search Documents

By Yuhua Wang, Haitao Zheng, Guangli Zhu, Yuehao Zhao, Fushun Yu, Dongfang Lu

"Spodumene, feldspar and quartz possess similar surface properties, which make the difficult to separate spodumene from other silicate minerals by flotation. The differences of crystal structure, surface property and floatability of three minerals were studied by various technical means. The results show that Li-O and Al-O bonds in spodumene structure are not strong and easy to be broken. However, Al-O and Si-O bonds in feldspar and Si-O bond in quartz are very strong and not easy to be broken. High contents of Al and Li on spodumene surface were found by XPS measurements, which is benefit for the adsorption of anionic collector. The surface energies of main cleavage planes of spodumene (110), feldspar (001) and quartz (001) are 1.88 J/m2, 2.97J/m2 and 2.68J/m2, respectively. Hence, the exposed surfaces of feldspar and quartz are not saturated and easy to adsorb OH- ions from solution and cause the lower IEP than spodumene. The contact angles of three minerals in water are lower than 16º, suggesting that the hydrophilicity of three minerals is high, and the order of hydrophilicity is quartz > feldspar >spodumene. Correspondingly, contact angles and flotation recoveries of spodumene are bigger than that of feldspar and quartz in presence of a combined anionic and cationic collector named YOA.INTRODUCTION Flotation technology plays most important role for the recovery of spodumene from pegmatite ore. Generally, spodumene with fresh surface is easy to be floated using soap and oleic acid as collector, and the best flotation pH range is 4.0 to 9.0. However, the flotability of spodumene will become worse when its surface was polluted by slime which produced by the weathering of spodumene and other silicates (Dresler et al. 1998; Moon and Fuerstenau 2003; Menéndez et al. 2004; Yu et al. 2015). In addition, the species of Ca2+, Fe3+, Mg2+ and other metal ions in pulp can not only activate the flotation of spodumene, but also the activation of gangue minerals, and then the flotation selectivity of spodumene from gangue minerals became wores (Wang and Yu 2007; Yu et al. 2014). In order to eliminate the negative effects of slime and metal ions on the flotation of spoddumene, the desliming and long time scrubbing with the addition of NaOH and Na2CO3 were adopted. Usually, NaOH shows the activation for spodumene flotation, and the recovery of spodumene increases with the increase of NaOH dosage. Na2CO3 can eliminate the non selective activation of Ca2+, Fe3+, Mg2+ ions in the pulp, and the concentrate grade of spodumene increases with the increase of Na2CO3 dosage. Anionic collectors such as chelants, hydroxamic acid, oxidized paraffin soap, naphthenic acid and oleic acid were widely used for the flotation of spodumene (Dresler et al. 1998; Moon and Fuerstenau 2003; Menéndez et al. 2004; Yu et al. 2015)."

Jan 1, 2018

By Lowell B. Moon

Concern over possible wartime shortages finally resulted in passage of the Strategic Materials Act in 1939. As authorized by one section of this legislation, the Bureau of Mines proceeded to investigate deposits of seven strategic minerals with the objective of developing tonnages of low-grade material that could be mined in an emergency. During the war, the size of the program and the number of strategic minerals were increased, and the objective was the more immediate one of aiding production. Since the war, the size of the program has been reduced, but the number of minerals on the strategic list continues to be large. The objective has returned to that of 1939. In the course of the program, more than 10,000 examinations were made and about 1,300 projects were run on deposits of 33 different commodities. A considerable contribution to war production was made in six of the commodities investigated, and a minor contribution was made in twelve others. Substantial reserves have been indicated in 19 minerals. Private interest is currently active in some of the deposits developed in 14 commodities.

Jan 1, 1950

By D. A. Reynolds

THIS REPORT gives results of an investigation of the carbonizing properties of two Tennessee coals, one from the Jellico bed in Campbell County and the other from the Sewanee bed in Marion County. Jellico coal and blends with 20 and 30 percent Pocahontas No. 3 coal were carbonized at 800° and 900° C. by the BM-AGA method. Sewanee coal was carbonized by the same method at 800°, 900°, and 1,000° C.; blends with coals of similar and different ranks were carbonized at 800° and 900° C. The coals were subjected to various physical and chemical tests, including complete chemical analyses, low-temperature assays, and agglutinating, free-swelling, friability, plasticity, and expansion tests. The Tennessee coal field is a part of the Appalachian field, which extends from northern Pennsylvania to central Alabama. The Jelico bed, one of the most important in the State, is part of the Jellico formation, which is above the Lee formation of the Lower Pottsville. Sewanee coal bed belongs to the Sewanee conglomerate and is stratigraphically lower than the Jellico bed.

Jan 1, 1953

By Mackenzie Burnett

An inducer-type pump, capable of injecting dry coal into a hydraulic transport pipeline has been developed and installed in a specially designed and fabricated slurry injector vehicle. The full scale prototype injector system can deliver up to 11 ton/min of coal into an 8-in pipeline t pressures up to 95 lb/in2. The Helical Inducer Injector operates on centrifugal principles with flow passing axially through helical pitched conical rotor. Water is delivered to the pump through an annular slot at the atmospheric pressure coal inlet. The spinning rotor maintains an air-core vortex of water which pressurizes the discharge housing. A screw feeds coal through the open inlet into this vortex. The inner radius of the vortex contracts as pressure is increased, giving a limiting maximum pressure which is proportional to the square of the rotor speed. Below this limit, flow rate, discharge pressure, und rotor speed re independent variables. The self-powered, 4 -in high slurry injector vehicle follows and receives ROM coal from a continuous miner, reduces the top size to 3-in, and delivers the sized coal to the injector feed screw for slurry formation and pumps it through a mobile hose attached to the vehicle's outby end.

Jan 1, 1983

By Francis Vanbellen

Umicore Precious Metals Refining operates an integrated precious metals smelting and refining plant in Hoboken, Belgium. Once a smelter and refiner of complex concentrates, the plant today?s feed consists exclusively of industrial and consumer recycled products, making it the world?s largest recycling facility for precious metals. Unlike the fairy tale of the Frog Prince, it took much more than a princess? kiss to successfully realize this makeover. A completely renewed plant has been built over the past decade. The most visible technological innovation was the commissioning of the Pb-Cu smelter. Its flexibility towards very different types of feed makes it perfectly suited as main entry to the Hoboken flow sheet. A new Cu-leaching & electro winning plant and precious metals refinery make up the Precious Metals Operations (PMO) whose targets are fast throughput and maximized yields for gold, silver and the platinum group metals. The Base Metals Operations (BMO), flexibly process the by-products from the PMO, valorizing ?impurities? like indium, tellurium, selenium and others. Off gas and waste water treatments ensure compliance with strict environmental standards. Precious metals recycling is an art that goes beyond mastering a unique flow sheet. Umicore Precious Metals Refining offers a complete recycling service, taking care of sampling and assaying, metals management and logistics. The quality of this integral service is recognized through the attribution of ISO certifications for our operational activities, sampling and the environmental care. And it?s an art that follows Michelangelo?s experience: ?Art is 5% of inspiration and 95% of transpiration.?

Jan 1, 2006

By L. F. Willmott

The Bureau of Mines at Morgantown, W. Va., has been investigating, on a pilot plant scale, various methods of gasifying bituminous coal with oxygen and superheated steam to produce synthesis gas, as part of the broader program of finding new uses for coal. Differences in the pressure gasification methods used have depended on differences in the manner in which the pulverized coal is fed to the gasifier. One of the methods of feeding the coal that was investigated was the continuous, integrated coal-water slurry system. Goal and water were first mixed to produce a slurry; then the slurry was pumped through a heated coil. to evaporate the water fraction; the resulting steam was superheated, and some of it was separated so as to adjust the ratio of the residual steam to the coal fraction and make the resulting mixture suitable for partial combustion with oxygen in a pressure gasifier. Both before and during this reported3 developmental work it was necessary to make an extensive literature search into the technology of aqueous slurries in order to establish design criteria for the pilot plant and to correlate results of various phases of the work with that of other investigators, The pilot work coincided with the commercial development of a long-distance pipeline for the transportation of coal as a coal-water slurry, and this fact tended to broaden the scope of the pilot plant work and the extent of the literature search. This bibliography is the compilation of the material that was collected.

Jan 1, 1963

By A. Bergmann

Location The Meggen Mine and the concentrator plant of the "Sachtleben Bergbau G.m.b.H." are located in the southern part of the Ruhr-district of the Federal Republic of Germany. The mine has been in operation for more than 100 years, but the concentrator described in this paper was built in 1962 and started up in January 1963. Goelogy and Mining The Meggen ore-body is of sedimentary origin and occurs in a zone of limestones, graywacke and shales of Devonion age. The average thickness of the deposit is 3 meters and, due to an intense folding of the area, the mineralized zone dips very steeply at 800 toward the north. The ore consists of 85 percent of sulfides and 15 percent gangue that mainly contains silicates from the host rocks. The principal ore minerals are pyrite (67 percent), sphalerite (16 percent) and galena (2 percent) with minor amounts of marcasite and only traces of chalcopyrite. As shown in Fig. 1, the sphalerite and galena are very finely disseminated in the massive pyrite of the Meggen ore, and a very fine grinding combined with a special flotation technique are required to liberate the valuable sulfides and to produce separate concentrates of lead, zinc and pyrite. Mining is performed by the sub-level stoping method and employs trackless equipment. Present operations provide ore from the 600 meter level. Annual ore production is 870,000 metric tons.

Jan 1, 1972

By Lowell L. Patten

The Federal Bureau of Mines participated with the National Aeronautics and Space Administration and Martin Marietta Aerospace in developing, building, and testing a portable X-ray fluorescence spectrometer for use as an analyzer in mineral-resource investigative work. The prototype battery-powered spectrometer, measuring I1 by 12 by 5 inches and weighing only about 15 pounds, was designed specifically for field use. The spectrometer has two gas-proportional counters and two radioactive sources, 109Cd and 55Fe. Preliminary field and laboratory tests on rock specimens and rock pulps have demonstrated the capability of the spectrometer to detect 33 elements, to date. Characteristics of the system present some limitations, however, and further improvements are recommended.

Jan 1, 1982

By The Staff, Explosives Research Center

The principal activities of the Bureau of Mines Explosives Research Center from July 1, 1962, to June 30, 1963, are described briefly in part 1. Part 2 gives short abstracts of publications that appeared during fiscal year 1963; in general, the research reported in these publications antedates the report period.

Jun 24, 1964

By FREDERICK H. WILLCOX

In the past the blast-furnace industry was under the stigma of being one of the most prolific sources of killed or seriously inj ured and permanently disabled workmen of any of the industries of the country. In the popular mind, labor at blast furnaces was little less hazardous than mining, powder making, or railroad work. This impression wasbased not so much on definite knowledge of the number actnally injured and the causes of injury as on the spectacular nature of the accidents that from time to time were described in the press. As with a mine disaster or a railroad wreck so with many furnace accidents, the number fatally injured in such accidents constitutes only a minor proportion of the workmen who suffer more or less serious injuries. However, the reader of the daily paper receives a distinct impression-of frightful and sudden disaster which is apt to be associated henceforth in his mind with work at blast furnaces. It is true that in the past this impression has not been without warrant, for from the time of the advent of Mesabi ores, taller furnaces, and faster smelting, which begain in the early nineties, the newspapers have chronicled a large number of blastfurnace disasters. Blast-furnace men have never assumed to tolerate failures in construction or defective control of furnaces. But the admitted hazards of the work are many, and the slow development of improvements in the construction and control of the furnace and its auxiliaries have occasionally given rise to a tendency to accept as a part of the day's work not only the unforeseen and difficultly controlled accidents but accidents whose recurrence might be stopped by the adoption of suitable preventive measures. In the smelting of iron, even more than in many other industries, safety is inseparably related to efficiency in production, and. the accidents strictly incident to work about the furnace are proportional in some degree to the success with which obstacles to smooth working are overcome. This relation does not hold, however, in regard .to such accidents as are incident to hand labor, falls, falling and flying objects, machinery, and the use of hand tools.

Jan 1, 1917

By Gil Espejo, Denise Duncan

"In Alberta, several initiatives are under way to form partnerships between educators and industry to work together in preparing a skilled and technically competent workforce for the future. One successful initiative is the Teachers in Business program which provides high school teachers one month paid internships in Alberta businesses. Initiated by the Science Alberta Foundation in 1992, this program has offered participating teachers a variety of work experiences and job shadowing tours in industry.A Growing Need of Education and Industry PartnershipsIn our ever evolving world, industry is in a tight race to keep up to date with new technology and to remain competitive. Industry is relying on the education system to provide them with the core base for their future workforce. To accomplish this, the education system needs the support of industry to develop the right focus to prepare its students for the race. What skills will our future workforce need? How can we best prepare our students for these needs?Teaching the latest in technology, especially at the high school level, is a major challenge. It is difficult for educators to keep abreast of the rapid changes in technology. High school graduates need exposure to the latest advancements. And so do their teachers. Students must be prepared to adapt to the challenges of the future, Le. global competition, rapid technological change and an expanding knowledge base."

Jan 1, 1995

By Charles L. Kimbell

Introduction Despite the focus on the so-called "high-tech" and service components of the economy, the minerals industry in 1987 continued to provide the world the overwhelmingly dominant share of the total raw material supply for all manufacturing operations. And, in the form of fertilizers and other soil treatment materials, minerals also supplied indispensable raw materials to ensure continued high production of the agricultural and forestry sectors of the world's economy. Moreover, the role of minerals as a source of construction raw materials was essential to that sector. On the basis of preliminary and partial statistics on world output of crude mineral commodities, 1987 appears to have been a year of further recovery from the recessional years of 1981-1983. The value of world crude mineral industry production (all mineral commodities including fuels) apparently advanced about 5% to nearly $1.1 trillion in terms of constant 1983 dollars.' That is significantly above the recently revised 1986 level of nearly $1.05 trillion, but still considerably below the record-to-date high of $1.27 trillion set in 1980, as shown in Table 1. That growth in value took place despite relatively flat world oil prices - oil being the most important component of the aggregate, as it has been for decades. There is insufficient information available to assess the total value of processed mineral commodities (refined metals, refined oil, manufactured fertilizers and the like). But a figure of $2.6 trillion (constant 1983 dollars) would be a quite conservative estimate for those materials derived only from primary or newly mined materials. And an additional, as-yet-unestimated increment should be added for processed materials derived from secondary raw materials - scrap and other reclaimed substances. From a world trade viewpoint, minerals and mineral products dominate in terms of tonnage. For example, in 1985, on a weight basis, mineral commodities including fuels constituted more than 58% of all goods moving through the Suez Canal and 53% of all goods passing through the Panama Canal. These waterways cannot accommodate giant tankers and ore carriers. So an even larger share of total oceanic trade is composed of minerals and mineral products. Yet, in terms of value, the share of the total accounted for by these industrial essentials is much lower than that accounted for by other commodities, most notably sophisticated high-tech equipment and other goods with a relatively high per-pound value. Worldwide data on the value of mineral export trade for 1987 is so incomplete at this writing that it is impossible to assess that actual level. Indeed, the compilation of similar available data for 1986 covers only the exports of nations with developed market economies. In 1985, these countries accounted for only 67% of total world exports of all goods. They accounted for only 41% of world exports of major mineral commodities: crude nonmetals; metal ores, concentrates, and scrap; mineral fuels; nonferrous metals excluding gold; and iron and steel. For these developed-market-economy countries, the value of exports of these major mineral commodities declined by more than 10% between 1985 and 1986. Most of the shortfall came as a result of a 26% drop in the value of fuels exports. If these patterns of

Jan 7, 1988

By A. K. Martin

Adaptive management can be described as a structured, iterative process of robust decision making in the face of uncertainty, with a goal of reducing uncertainty over time through system monitoring. Adaptive management is a tool which can be applied to not only change a system, but learn about the system (Holling, 1978). Adaptive management has been used in ecosystem management for years and guidance is provided in a variety of handbooks and publications. Adaptive management can be applied to industrial facilities and mines through the use of an adaptive environmental management plan (AEMP) and associated practices. The goal of this paper is to provide an explanation of how the plans and practices support regulatory agency approvals and permitting, span the life-cycle of mines, manage uncertainty, and assist in addressing mining impact and legacy issues. AEMPs and associated practices are useful tools to address the uncertainties in identifying, evaluating, and managing impacts of proposed new and modified mining facilities undergoing environmental review. Once a proposed project is approved, the AEMP continues as a living document, being informed, revised, and adapted by the operations. The AEMP can serve as an ongoing management tool for describing and evaluating environmental impacts, continuing in operations into post reclamation. If initiated during planning and environmental review of a project (and in some locations such as the United States [U.S.], the preparation of an Environmental Impact Statement (EIS)), the AEMP becomes a basis to identify, monitor, and manage potential project environmental impacts. Development of an AEMP for an operating mine is also beneficial since there are generally developing and ongoing environmental issues at those facilities as well. Over time, the AEMP is adapted to changing requirements and conditions including those anticipated and unanticipated. Ever increasing scrutiny of mining projects and the complexities of the EIS process highlight the uncertainties inherent in impact predictions. In making the momentous decision of initial project approval, these uncertainties can discourage the regulatory agencies? actions and create stakeholder anxiety and controversy about a project. A well-designed AEMP can support the decision to approve an EIS and enable a project to move forward. Additionally, an AEMP can inform financial assurance estimates and revisions over the life of a mine providing all parties including the citizens of the surrounding communities with greater confidence that potential environmental impacts and risks will be well managed.

Feb 23, 2014

By L. E. Cardwell

This publication contains routine analyses and related source data for 299 natural gas samples from 22 States and three foreign countries. All of the samples were collected during calendar year 1972 as part of a continuous survey of the free world for occurrences of helium in natural gas. This survey has been conducted in the United States by the Bureau of Mines since 1917. In late 1965, the survey was expanded to include foreign gasfields. The analyses published herein were made by mass spectrometer and a special helium analysis apparatus, which are described in Bureau of Mines Bulletins 4863 and 576.4 Fourteen previous publications have presented the results of 9,902 gas analyses prior to 1972. The first three, Bulletins 486,5 576,6 and 617,7 contain analyses and related source data on 5,218 gas samples collected from

Jan 1, 1973

By L Lorenzen

The selection of samples for metallurgical test work is generally focused on providing geologically representative samples. One of the major problems experienced with metallurgical test work using drill hole data, is the small sample sets selected for metallurgical testing. Major process and financial decisions are being made from results obtained using snapshot samples. Snapshot samples means that samples are basically selected only by grade and spatial location with the assumption that the rest of the orebody or portion of orebody is similar and will respond metallurgically the same way – ie the assumption is that the mineralogy and lithology are basically the same as the test sample. From the test work, algorithms were usually developed and used to describe throughput and recovery using some explanatory variables including grade (mineral chemistry) and ore hardness. These algorithms were then used in the recovery models to determine tonnes produced and plant throughput. However, the metallurgical parameters are a function of many geological factors including grade, lithology, alteration, mineralogy, spatial relationships and SG. In previous years, the limited mineralogical information available was deemed enough for the metallurgist to make decisions as to how many samples are needed to evaluate the metallurgical performance of the ore during processing, and subsequently the basis for the plant design. If the orebody is consistent and not complex or refractory (thus, relative simple lithology), then only spatial and grade samples will be needed to evaluate the throughput and recovery, so limited mineralogical information may be acceptable. There is now, however, an increasing realisation that the mineralogy and geology change, as do the metallurgical characteristics of the orebody, so limited samples may not be sufficient for effective metallurgical test work.It is the purpose of this paper to discuss the effect correct mineralogical information has on the subsequent metallurgical test work program and process selection using a case study. Factors such as type of rock, rainfall and topography are thought to influence the minerals that ultimately form in various orebodies, with the result that different orebodies often react differently during metallurgical test work programs. It is therefore important to obtain accurate mineralogical and elemental deportment data, which will also indicate where the valuable metal containing minerals are located within the orebody. The better you plan and execute your metallurgical test work program during the early phases, the more accurate the decision-making process will be during the selection phase. Improved integration between geology and metallurgy data gathering (geometallurgy) during early phases will result in more accurate predictions with regard to throughput and recovery during modelling and process. Equipment selection will be considerably simpler in later phases with early planning, with improved mine and process scheduling and subsequent net present value (NPV).

Sep 5, 2011

By J. Restrepo, N. Ripepi

"The International Organization of Standards defines risk as “the effect of uncertainties on achieving objectives (15).” In mining, many uncertainties can influence the outcome of personal or professional objectives and are often difficult to predict. Risk management, the minimization and control of adverse effects from exposure to identified risks, is a well-established concept that can summarized as “being smart about taking chances” (12). Risk management now consists of management processes unique to numerous organizations across many industries, as varying sectors encounter a variety of needs, including the analysis and mitigation of risks related to physical security, product liability, information security, various forms of insurance, regulatory compliance, and workplace safety (12). The reoccurrence of multiple fatality events in the US mining industry, especially the underground coal sector, suggests an opportunity for improved methods of major safety hazard identification, assessment, and mitigation. A risk management approach would include ready identification and mitigation of these risks, inclusive stakeholder engagement, and rapid integration. While many solutions to reducing the risk of mine disasters have been proposed including stricter regulation and improved technology, a comprehensive risk management approach has yet to be fully integrated in the US mining industry. In December of 2006, R. Larry Grayson of the National Mining Association’s Mine Safety Technology and Training Commission called for “a new paradigm for ensuring safety in underground coal mines, one that focuses on systematic and comprehensive risk management as the foundation from which all life-safety efforts emanate (7).” A risk management approach has already been implemented with success in Australia’s minerals industry as part of a transition during the mid-1990s from a prescriptive based health and safety attitude to a more proactive, duty-of care [risk-based] philosophy (13, 16, 17).FUNDAMENTAL ELEMENTS OF RISK MANAGEMENT TECHNIQUES The fundamental components of a comprehensive risk assessment/management program are well-established within the realm of mining health and safety. Figure 1 depicts the elements of a typical mining hazard management framework. The first step in any safety-based risk management system is to identify and assess hazards by their location, nature, and magnitude within a mine. Next, a decision is made about choosing to eliminate, mitigate, or tolerate each hazard. Ideally, a hazard will be eliminated during the design stages of mining, though dynamic mining conditions often require continuous improvement and reevaluation of existing hazard controls. If elimination is not possible, hazard mitigation actions can consist of methods, rules, equipment, competencies, or other mechanisms. If a hazard is simply tolerated, as many inherent mining hazards must be, then specialized administrative controls must be utilized to minimize losses. During this process, the performance of each action is monitored and modified as needed (13)."

Jan 1, 2015

By Guenter F. Lehmann

This report summarizes the results of the development and testing of a prototype monorail suspended bridge conveyor (MBC) system as a method of continuous haulage In underground mining applications. Included are the results of full scale, surface and underground testing of the complete MBC system. Conclusions drawn from these results, together with recommended modifications, supports the viability of the MBC system.

Jan 1, 1988

By J. W. Kramers, R. A. S. Brown

"Samples from seven test wells distributed throughout the surface-mineable area of the Athabasca Oil Sands have been evaluated to determine the amounts of heavy minerals present and the titanium and zirconium contents. The samples were treated to yield the size distribution of the titanium and zirconium minerals as well as their spatial distribution. The study has shown that heavy minerals are found throughout the surface-mineable area; concentrations range from 0.24 to 2.29 per cent (by weight), with a mean of 1.02 per cent. Titanium and zirconium contents vary throughout the area, and are found preferentially in the finer size fractions. •on the basis of preliminary calculations, the tailings streams from an oil sands plant would provide sufficient feed for a large-scale titanium pigment plant, and the tailings from one plant would provide sufficient zircon feed to satisfy Canadian demand for. metallic zirconium. Variability of the heavy mineral content and composition is such that the heavy mineral potential must be evaluated in detail for each mine site."

Jan 1, 1976

By Humphrey Dean

"Canadian mining companies now operate numerous Koepe-type friction hoists in a variety of different shafts, most of which have a depth in excess of 3,000 feet. Rope performance reliability is an absolutely essential ingredient of most installations and, for this to be provided, a more comprehensive understanding of rope reactions to applied stresses is required.It is the intent of this paper to illustrate for the operators the importance of the critical stresses encountered and to provide a maintenance program designed to circumvent potential difficulties."

Jan 1, 1970

By Xingkai Wang, Wenbing Xie

"To control the large deformation of soft rock around the roadway subjected to high stress, it is important to improve the stability of support structure, in addition to increasing support strength. In this study, the causes for the destabilization of U-steel frame and its loading characteristics were analyzed by theoretical analysis, laboratory experiments and field tests. The technology of constant support resistance, the principle of support structure compensation and the compensation technique are proposed. The results indicated that the main reasons for frame structure destabilization are caused by low strength of connector, irrational structure of connector, poor interaction between the surrounding rocks and support frame and structure, and unstable support structure. Thus, the corresponding technological measures, such as connector with high strength and rational structure are adopted. The bearing capacity of frame is unstable after slipping. In order to maintain the high support resistance when the frame is performing the support function, the frame connector should be retightened after slipping. Though the working resistance may be improved greatly by using the backfilling or back grouting of U-steel, the frame remains unstable because of the unstable frame structure. Therefore, according to the deformation characteristics of rocks surrounding the roadway and the structure instability of U- steel frame, the stable structure device is used to carry out the structural compensation of U-steel frame, and the whole bearing capacity of the frame and its structural stability are improved greatly.INTRODUCTIONThroughout the development of the roadway supports for coal mines in China, it can be seen that the supporting strength and supporting resistance increase continuously with increase in mining depth and supporting difficulties [1]. With respect to the ground control mechanism and supporting technology of rocks surrounding the soft rock roadways subjected to high stress, considerable research has been done both at home and abroad. The backfilling technology behind the high-resistance and yieldable U-steel wall, the new type of grout/bolt support technology and the bolting with high-strength mesh support technology were developed, and have been used widely in coal mines with notable economic benefits [2-7]. However, a large number of engineering practices show that in many cases the existing rock control technology of roadway may not control the large deformation of the soft rock roadways subjected to high stress. The reason that the large deformation of soft rock roadway occurs is mainly due to poor structure stability of existing frame bearing structure, not insufficient support strength."

Jan 1, 2015