Search Documents

By Michael W. Milner

Cold Ocean Placers: Polar storms, interstadial littorals and crustal adjustments. Polar storms with consistent strong winds in the Southern, Antarctic Ocean are responsible for placer deposits on both the east and west coasts of Australia, on the west coast of New Zealand, as well as on the coasts of South America and Africa. Arctic winds, confined by both land and ice, generate similar placers in Labrador and Greenland as well as on the coasts of Scotland, Norway, Hudson's Bay, Nome, Goodnews Bay, Kamchatka and the north coast of Siberia. Tasman and Labrador seas have several parallels to Newfoundland, including north-south polar waterways, young spreading ocean floors, and youthful coastal escarpments with glaciated coasts. Black sand beds in beach deposits on the modern and Pleistocene transgression strandlines, skewed to the distal ends of beaches, and set into either bedrock or sediment fill, are the locus of the light-heavy mineral placers with titanium, zirconium and rare earth elements; chromium; iron; and tin. Gold and platinum group elements are the ultra heavy minerals at one end of the spectrum and tend occur in proximal placers generated, either directly from bedrock sources, or as minor by-products in distal light-heavy mineral placers. Diamonds are unusual in that the value is only in the larger stones, despite the formation of beach sand and aeolian placers in the littoral zone, and the sites of concentration are in very high energy bedrock traps, on terraces that are mined to depths of 100 metres below sealevel.

Jan 1, 1995

By Gerhard Finstermann, Ichiro Maeno, Takehiko Saito, Hironori Shimogama, Konrad Krimpelstätter

Automobile manufacturers are developing Electrified Vehicles with light steel body structure designs that reduce mass and therefore greenhouse gas emissions over the vehicle’s entire life cycle. This raises the demand for the production and development of Advanced and Ultra High-Strength Steels (AHSS / UHSS) and Electrical Steels with increased permeability and reduced core loss to improve energy conversion efficiency. To meet this requirements the steel market is tending towards new generations of AHSS with improved formability (3rd generation AHSS) and high-silicon steels with higher strength and thinner products. With this growing demand for advanced high-strength steels and electrical steels, producers are faced with a unique and interesting challenge in producing materials that strain or exceed the capabilities of existing mill equipment and automation designed to produce low- to medium-carbon sheet. While specialty steel producers have known for decades how to process special high-strength steels and thinner gauges, this equipment typically does not offer the yield and productivity desired by the market, necessitating innovation in re-engineering existing equipment to meet the market demands more economically than new construction. In the case of cold rolling, this can be supported through variable roll geometries, more effective roll-gap lubrication technologies, application of strip heaters (Warm Rolling) to reduce risk for edge crack propagation and strip breaks as well as continuous rolling managed by state-of-the-art automation technologies.

Oct 1, 2019

By John Lund

INTRODUCTION GOLD-BEARING placers of Alaska and the Yukon Territories are buried under a layer of permanently frozen alluvial overburden, or 'muck', which varies in depth from twenty to one hundred feet. The placers, and the decomposed bedrock layers upon which they are deposited, are also permanently frozen. During the summer, surface muck which is exposed to the sun will thaw, but only to a depth of a few feet. To reach a valuable deposit, the frozen overburden must be either penetrated with shafts, or stripped from the deposit entirely. In either case, before the placer can be mined, it must be thawed. At modern dredging operations, the frozen muck is stripped from the placer by powerful jets of water from hydraulic giants. The placer, and several feet of decomposed bed-rock, are then thawed by forcing water through narrow pipes which have been driven into the deposit. Other methods of thawing frozen placers were used extensively during the early years of the Klondike 'gold rush', but experimentation later proved that creek water at its natural summer temperature was a more effective and economical thawing medium than any other which had been used. EVOLUTION OF COLD WATER THAWING Early prospectors of the far north reached placers by digging shafts through the frozen muck. They then thawed the placer sand and gravel by building wood fires at the bottom of the shafts.

Jan 1, 1951

By Paul Hosford, B. Thrall

There has been a surge of exploration activity and interest in mineral properties located in cold Northern climates, with gold and copper properties as the two most attractive targets. There are already a number of mining operations located in the Arctic, for example, Red Dog, Polaris, and Lupin, all located in the Canadian Arctic. The logistics of sustaining operations, the engineering design and construction methods for such inhospitable regions are now relatively well understood. However, at least three of the proposed new mines in the Yukon Territory, Canada are designed to be heap leach operations. Rescan Engineering has recently completed Feasibility studies for two heap leach operations in the Yukon, one of which, the Brewery Creek Mine, is now in operation. The purpose of this paper is to explore some of the engineering and operating concepts that have been developed to make heap leaching an appropriate process method for gold recovery in a cold climate. Many of the readers will be familiar with the general and specific details of heap leaching, and it is not the intention of the authors to deal with any of the established "do's" and "don'ts" that have been addressed in numerous previous papers, but only with those pertaining to cold weather operations. This paper also examines these design concepts in specific relation to the results of the first winter's operation at Brewery Creek Mine, the first "far" North heap leach operation.

Jan 1, 1997

By Zolfan F. Oszter

As exploration for new mineral deposits advances farther into the Canadian North, the more the design engineer is faced with the problems of cold weather conditions. This is especially true when designing belt conveyor systems for open-pit operations where the temperature in the winter may go to -40°F or below. Problems with the mechanical components and also with the belting will arise, which in turn may reduce the availability of the system. This paper outlines the problems encountered during cold weather operation and what precautionary measures must be taken into consideration in the design of equipment, as well as in the selection of materials, in order to ensure a system which will maintain production. THE conveying of ore and waste in the pit or to the processing plant poses problems during cold weather, when temperatures may drop to -4o?F or be-low. Troubles with the mechanical components, the belting or the supporting structure may arise, and this, in turn, will reduce the availability of the conveying system.

Jan 1, 1965

By George J. Thompson

Almost all persons connected with mining industry have had an exasperating experience like the following: 'On a cold and frosty morning in mid-January, you find yourself quite happy with the world. Production is up and the mine has been running smoothly. All at once the radio cracks up your tranquility -- 'so and so' piece of equip¬ment has broken its 'whatzit'. Now the iron is in the fire, and things have to be fixed quick.!' This can be a major failure which will bring the whole operation to a grinding halt or just one of the numerous maintenance headaches on an auxiliary piece of equipment. After one has experienced a major or minor catastrophe, he has to wonder whether some other methods with respect to design and maintenance would help prevent these unexpected calamities. The objective of this paper is to gain an insight into the charac¬teristics of steel at cold temperatures so that better decisions can be made with respect to maintenance and repair of mining equipment. Most machinery and their structures are exposed to cold temperatures. Even in locations as far south as Alabama and Arizona, brief periods of cold in winter months can adversely affect the ability of mach¬ines to do their work. To understand the background of cold temperature brittle fracture, jet us examine its basic elements. First, when steel gets cold, it gets brittle. This is best described by Figure 1. This graph shows a typical stress/strain curve of a mild or medium grade steel at room temperature. Stress is defined simply as the amount of force acting on one square inch of

Jan 1, 1972

By George J. Thompson

The need for studying brittle fracture is defined; the main elements of this type of failure are explained; and the mechanism at crack initiation is outlined. Various design and maintenance practices which can preclude costly downtime caused by unexplained machine failures are proposed.

Jan 1, 1974

By Manuel Pérez-Tello, María M. Salazar-Campoy, Óscar Rodríguez-Hoyos

The Kaldo furnace is a type of top-blown, rotary reactor that is widely used for the production of precious metals. During the production of doré, a gas jet of compressed air is injected through a water-cooled lance to impinge upon the molten bath surface in the presence of molten metal and a slag phase. A common problem during operation is the difficulty in controlling the distance that the injection lance can penetrate through the reactor mouth without being splashed by the molten phases. Splashing may produce accretions on the lance surface as well as plugging of the nozzle at the lance tip. An additional problem may occur when the gas jet impinges upon the furnace wall and causes rapid wearing of the refractory linings. Because the conditions prevailing in the Kaldo furnace offers poor visibility to the human eye, its operation mostly relies on the empirical knowledge of plant operators and process engineers. A systematic study in a scale model of the Kaldo furnace under controlled laboratory conditions may be valuable to estimate the maximum penetration distance of the injection lance, and thus help improve the operation of an industrial reactor. From a fundamental perspective, the observation of the basic features of the flow patterns in the scale model may help elucidate the relevant phenomena governing the hydrodynamics in this type of system.

By Manuel Pérez-Tello, María M. Salazar-Campoy, Óscar Rodríguez-Hoyos

A common problem during the operation of the Kaldo furnace is the formation of accretions and blockage of the injection lance due to splashing. This typically occurs during the processing of anodic slimes for the production of doré. In this work, a 1:7 scale model of the Kaldo furnace currently in operation at Metalúrgica de Cobre, Mexico, was built in transparent acrylic plastic. Water and colored oil were used to represent the doré and slag, respectively. The model was used to determine the maximum penetration distance of the injection lance under a variety of experimental conditions at room temperature. Input variables included two types of oil, rotation speed, inclination angle, and the fraction of the vessel volume occupied by the liquids (φ). A mathematical correlation for the dimensionless maximum penetration distance of the injection lance d ∗ as a function of φ, the Froude number of the liquids in the vessel (Fr), the Reynolds number of the gas jet (Re), and the oil-to-water kinematic viscosity ratio (η)was developed. Reasonable agreement between the calculated and experimental values was obtained. Digital images showed that splashing was caused by the turbulent gas jet impinging upon the free surface of the liquids, whereas the cascade effect was negligible. The results of this work have been useful to improve the operation of an industrial Kaldo reactor.

By R. A. Beall

This bulletin reviews the historical background of the cold-mold arc-melting technology, with specific references to the development that led to homogeneous zirconium ingots. Descriptions are given of modern production arc-furnaces for vacuum melting of troth exotic and conventional metals. Besides zirconium, specific data are given for production of chromium, thorium, and copper. The development of the skull-casting technique for titanium is detailed, and the application of the technique to such refractory metals as molybdenum and tungsten is described. Factors of operation of the apparatus and furnace design are considered.

Jan 1, 1968

By L. A. Cornish, I. A. Mwamba, R. A. Couperthwaite

"In previous work by the authors, it was established that additions of 0.2 at.% Ru to an Fe-40 at.% Al alloy improved the corrosion and oxidation resistance of the alloy. The alloy was produced by mechanical alloying and spark plasma sintering and the work showed that nonequilibrium processing was able to significantly refine the grain size of the material. The sintered material had a higher hardness than the as-cast material and the change in grain size did not significantly affect the oxidation and corrosion. In the present research, the mechanically alloyed powder was coated onto a mild steel substrate using cold-spray coating at a gas pressure of 10 bar and a temperature of 500°C. The coatings were found to be 5–10 um thick, although thicknesses of up to 30 um were observed. The coated materials were subjected to oxidation and corrosion tests to determine the effectiveness of the coating in increasing the oxidation and corrosion resistance of mild steel. This was done to determine the effectiveness of cold-spray coating as a technique to coat these mechanically alloyed powders. IntroductionPrevious work conducted by Mintek (Couperthwaite et al., 2013, 2015) investigated the effect of precious metal additions on the structure, oxidation and corrosion properties of an Fe-40 at.% Al (Fe- Al) alloy. Initial work determined that additions of more than 0.5 at.% precious metal did not improve the oxidation and corrosion properties of the materials and in some cases even decreased the resistance to corrosion. Further work identified Pt and Ru as beneficial additions to the FeAl alloy. Four alloys were then produced by mechanical alloying and sintering (FeAl–0.2 at.% Pd, FeAl–0.2 at.% Ru, FeAl–0.5 at.% Ag, FeAl–0.5 at.% Pt). These alloys were all successfully produced by melting and casting and mechanical alloying sintering and it was found that the nonequilibrium processing greatly decreased the grain size of the materials compared to the ascast materials. It was found that the additions of Ru and Pt were still the most beneficial to the oxidation and corrosion properties, with Ru being considered the most beneficial."

Jan 1, 2016

By George J. Thompson

This pa per deals with the internal characteristics of steel and its response under cold northern temperatures. General maintenance procedures and specific repair techniques are covered.

Jan 1, 1973

By M. Mohammadijoo, J. B. Wiskel, D. G. Ivey, S. Kenny, H. Henein

Cold-wire tandem submerged arc welding (CWTSAW) has recently been developed as a novel welding technique to replace the conventional tandem submerged arc welding (TSAW) process and improve the productivity of pipeline manufacturing. The process involves two electrodes with arcs and one electrically cold electrode. Since heat-input of the welding process is a key factor affecting the properties of the weld metal (WM) and the heat-affected zone (HAZ), and the additional cold-wire affects the heat introduced to the weldment, it is of interest to investigate property and geometry changes in the WM and HAZ when a cold-wire is added to the welding process. In the current research, the CWTSAW process is investigated and optimized by correlating the main welding parameters with the micro-hardness of the WM and HAZ and the geometry of the weld, i.e., the bead width (BW), penetration depth (PD), reinforcement area (RA) and coarse grained heat-affected zone (CGHAZ) area. Three statistical and mathematical methods are employed to optimize the CWTSAW process in terms of the mechanical properties and WM and HAZ geometry of a typical microalloyed steel used for pipeline manufacturing.

Jan 1, 2015

By F. Alsobrook

Coleman Quartz Inc. has a long history as the sole U.S. producer of lascas for the cultured quartz growing industry based on its unique deposits in Arkansas. Since 1989 the company has also been producing metallurgical grade silica for the ferrosilicon industry from a deposit of unusually pure Arkansas novaculite. This paper chronicles Coleman's trans-formation of an abandoned railroad ballast quarry into a generator of $1.5 million in annual sales to a nontraditional novaculite market. Potential additional applications for this high quality silica rock will also be mentioned.

Jan 1, 1992

By William T. Griswold

Few metals or industrial minerals can boast a better growth record over the past fifteen years than the borates. This period of growth occurred before the influence of any large-scale use in plastics or high-energy fuels. These new developments not only provide expanding markets, but the programs related to their development are generating research information that will lead to many other new uses. The most dynamic growth areas for refined products of boron or borates are in the acid, the oxide and the reduced forms, such as the metal and the hydrides. Expanding requirements for these products will modify the emphasis on the use of naturally occurring sodium borates. Any borate from which boron can be economically extracted will become a potentially important ore. This is particularly true of the calcium borate, colemanite. Only one large deposit in the Western World has ever been developed where the principal economic minerals are sodium borates, This factor alone would discourage any exploration program directed solely toward the discovery of these ores; on the other hand, ample exploration opportunities for calcium borates exist in the desert regions of California and Nevada. It is therefore reasonable to restrict a program to this region, in spite of geologically favorable areas in foreign countries such as Turkey, Argentina and Chile.

Jan 1, 1959

By Levent Özmen

Colemanite is a mineral containing varying amount of boron that is found in abundance in Turkey. It has a good possibility to be used as a flux in iron and steel industry. In this study a review of the use of colemanite, as a flux agent in steel production has been carried out and various related aspects such as its influence in metal-slag reactions, solubility of lime and magnesia in the slag are discussed along its performance in several points of views including its technical and environmental usage characteristics. Positive and negative factors of using this material as a flux are also underlined.

Jan 1, 2006

By Paul Lynch

"Since being reported to the 2012 UMI in Shanghai, the Cook Islands has been steadily developing for the commencement of it Seabed Minerals sector in its large Exclusive Economic Zone which contain a vast and unique Manganese Nodule resource, estimated at 10 billion tonnes1. At the 2013 UMI in Brazil, it was reported that the Seabed Minerals Act had commenced and all the necessary complex Technical aspects of this developmental work was being undertaken. At the 2014 UMI in Portugal, full details of the final developments leading to the opening of the Tender of Exploration Blocks in the Cook Islands EEZ will be presented in a brief but comprehensive method, using Poster displays, Powerpoint and active Website interaction. This will show the drafted Regulations, prepared on best international standards, to address both Licencing and Environmental requirements, to give clarity and security to the Resources Owner, industry and stakeholders. This work in being coordinated by the Cook Islands Seabed Minerals Authority, with the valuable collaboration of many international, regional and national stakeholders, including the Cook Islands NGOs, Marine Resources, Marine Park and National Environment Service."

Sep 1, 2014

By D Kilkenny, D Nardini, P Kline

This paper is a case study highlighting learnings and success in two areas challenging underground miners: change management and collaboration. It examines the implementation process of a new automated loading system in the bulk stoping area of Telfer Mine in Western Australia, controlling multiple load haul dump machines. Here, the new technology has brought together different functions and different companies to deliver a well performing automation system in a changing and challenging mining environment. The introduction of a new and different technology on site has driven collaboration between all stakeholders to break down the traditional barriers to achieve the sustained performance required. Historically, different teams have operated within silos and not always aligned to deliver a ‘best for project’ solution. Technical teams focus on the mine design, maintenance teams focus on reliability and operations execute the plan. Mining contractors focus on productivity and cost. Manufacturers focus on supply of goods and service. Optimising each silo individually is not guaranteed to provide an optimal mining solution. Involving elements from each team as seen at Telfer, has resulted in an optimal mining solution for the automated loading system. A change of focus from the technical teams to include automation parameters in the mine design; operability and maintainability built into the system design allowing for collective ownership and responsibility resulting in a more resilient solution. The implementation of the new technology was not only a technical change but more importantly, successful management of change. Elements of successful change management such as communication, vision, leadership and planning, are essential to harness a trusting site culture which is responsive to new technology. Learnings and challenges from this change process will also be discussed with the intent to improve the success rate and timelines of technology implementations in the future.

Mar 15, 2021

By Tony Breuer

Can international development NGOs and the mining industry find common ground and work together in the Third World? The Canadian Hunger Foundation/PARTNERS in Rural Development (CHF-PARTNERS) has, over the past forty years, implemented more than 800 rural community development projects in some 38 countries of Africa, Asia, and the Americas. Working with or for the Canadian mining industry offers both opportunities and risks. We can help a mining company ensure that the workers, their families and communities share adequately in the economic and social rewards from a mining operation in their area. We can contribute to the provision of sustainable livelihoods when an operation winds down. The company?s reputation as a good corporate citizen can be enhanced. On the other hand, mining companies and NGOs have generally very different values and missions. The risk of misunderstandings from conflicting motives and work practices is correspondingly high. Both partners must state their values and expectations clearly at the start of collaboration. The NGO must ensure that the company abides by acceptable ethical standards. It must not directly or indirectly subsidize a private company from its charitable donations. The mining company must satisfy itself that the NGO has the capacity, resources and experience to produce the results expected.

May 1, 2001

By W. E. Oching, M. M. Ghomshei

Attracting and retaining workers in mining industry has become an uphill battle to many mining companies. As workers with significant experience retire, it is getting more difficult to attract not only new workers but also top talent to the mining industry to replace professionals exiting the workforce. To make matters worse, students’ enrolment in the post-secondary mining programs in Canada and USA is continuously declining year after year for reasons not directly linked to job market. This raises a question of how can the future needs of mining be met? This paper focuses on avenues for collaboration of industry and educational institutions to meet the current and future needs of mining. It provides effective approaches that mining institutes can engage with program advisory committees, role of the mining industry in supporting both faculty and students, how to harness the benefits of diverse workforce in the country and use of innovative technologies to attract young workers in mining. This work presents Human Resources (HR) professionals with tools that they can use to hire and retain skilled workers with strong interest to work in the mining industry. It also provides HR professionals with an opportunity to re-evaluate their restructuring practices during economic downturns as they reduce number of employees on temporary or permanent basis. The paper stresses the need of working together of the mining stakeholders including mining industry, academic institutions, First Nations’ communities and provincial(state) and federal governments to meet the current and future demands of mining as the industry experiences shortage of labour and low students’ enrolment in post-secondary mining programs. It is shown that mining educational institutes can enhance their programs and recruitments through establishing a better communication with all stakeholders. This communication can be facilitated by creating a national advisory board, to work with all mining programs at the national level for sustainable mining.

Jan 1, 2023