Search Documents

By Yong Hack Lee

Nonferrous smelting processes have been through a rapid transformation since the beginning of 1980. The copper smelting technology has changed from the conventional Blast Furnace process to the Flash Smelting and MIB process. In the field of lead smelting, the technology has changed from the Blast Furnace Smelting to the Direct Smelting such as QSL and KIVCET. In 1992, Onsan Refinery successfully commissioned Direct Smelting QSL technology for lead. The QSL could produce more than 160,000 ton per year of lead bullion from lead concentrate and various residues. Moreover, since the year 2000, the TSL (Top Submerged Lance) Technology utilizing the same Direct Smelting process has been successfully commissioned to treat lead concentrate as well as lead sulfate residue produced from a hydrometallurgical zinc plant. This paper presents and compares the energy flows of lead smelting processes such as a conventional process and the Direct Smelting Processes plotted on the Pb-O-S phase diagram. The oxygen potential diagram suggests how to control the oxygen potential in the fum ace. Also, it describes the recent operational experience in the TSL plant of Onsan Refinery with necessary mass balance of key elements.

Jan 1, 2003

By T. B. Braun

Cathode contamination is the principal factor affecting the quality of electrorefined copper. It is commonly accepted that annealability is unfavorably affected by the following elements, in decreasing order of adverse effect: tellurium, selenium, bismuth, antimony, and arsenic. Silver in cathodes has importance as it represents a nonrecoverable loss of silver to the refinery. Mechanisms for the contamination of cathodes by these elements are examined and the effect of operating variables on contamination, including anode composition, electrolyte composition, electrolyte temperature, addition agent practice, and electrolyte discard rate, are discussed.

Jan 1, 1976

By Mei-le He, Min Chen, Xiang Shen, Lei Xu, Lei Liu, Nan Wang, Xue-liang Yin

In the current study, Al2O3-MgO-CaO refractories were prepared at 1400-1600 by the addition of MnO micro-powders, and the effect of MnO addition on densification behavior of the refractory was discussed. The results showed that the doped MnO dissolved to MgAl2O4 phase, and promoted the growth of MgAl2O4 grains by the formation of MgAl2O4 solid solution. As a result, the dense microstructure was obtained, with the apparent porosity decreased from 19.2% to 5.4% and the bulk density increased from 2.78g/cm3 to 3.15g/cm3 after firing at 1600 for 2h by the addition of 4% MnO. In addition, a texture microstructure was observed, which is considered to be favorable to improve mechanical properties and the service life of Al2O3-MgO-CaO system refractories.

Jan 1, 2016

By Renxing Li, Yongyong Gong, Yufeng Cheng, Zhenxing Yin, Xin Cao, Qijie Zhai

"The influence of electric current pulse (ECP) on the solidification structure of SUS430 ferritic stainless steel (FSS) was investigated in the current study. The technology of ECP has been widely used to improve the properties of metals with relatively low cost. The parallel electrodes were inserted into the free melt surface to constitute a current loop. The different influences of three parameters on solidification structure were studied by changing the peak current value, frequency and treating time respectively. The results indicated that the ECP significantly increased the number of equiaxed grains of SUS430 FSS. The as-cast structure without ECP treating was almost wholly columnar, while the number of equiaxed grains of the specimen, which was treated 3min with a peak current of 400kIA, increased to 2698 in the observed surface. To get the best refinement, an optimum range of these three parameters is required and the peak current value plays the most important role.IntroductionFor the lack of nickel resource and the pressure of environment protection, ferritic stainless steel is increasingly adopted to replace the austenite stainless steel because of its low nickel content and good mechanical properties. SUS430 steel is a typical example with excellent performance and relatively low price to replace the application of austenitic stainless steel[1-3]. This type of steel with high thermal conductivity coefficient, low expansion coefficient, good oxidation resistance, excellent stress corrosion resistance and other fantastic characteristics is often used to make components which need to have resistances for atmosphere, water, steam and oxidizing acid corrosion[4]. Since the developing of columnar grains and low toughness at high temperature, its products are easily crinkled and cracked during the subsequent rolling process[5]. The application of ferritic stainless steel is limited by these defects[6-8]."

Jan 1, 2012

By J. L. Johnson

Remediation of small-arms firing ranges is being investigated by the Naval Civil Engineering Laboratory and the U.S. Bureau of Mines. Scheduled closures of military installations, as well as the management of active ranges, require the development of methodologies for heavy metals removal to prevent their entering the surrounding environment. The impact berms contain high concentrations of metals, and the soil and vegetation surrounding the berms were found to have slightly elevated levels. The heavy metals characterized are in the form of whole bullets, a wide size distribution of free fragments, smeared lead on the surface of the soil grains, and very finely attached particles. Gravity beneficiation can remove liberated metal contamination effectively. Weak acetic acid leaching shows promise in lowering the final metal contamination to allow the soil to pass the Environmental Protection Agency's (EPA) Toxicity Characteristic Leaching Procedure (TCLP) criteria.

Jan 1, 1991

By Guolin Zheng, Jian Pan, Deqing Zhu, Xianlin Zhou

"In ferronickel production, nickel oxide and part of the iron oxide are reduced to metal by agglomeration and smelting in blast furnace. Due to the physical and chemical properties of the laterite ores, a large fraction of fines is generated during the pre-treatment stages and the strength of agglomeration is weakened, which results in low productivity and bad quality. In this paper, the process of pelletization of nickel laterite was developed, and some parameters to strengthen the pelletization of nickel laterite have been optimized. The results show that the compressive strength of fired nickel laterite pellet can reach over 2000 Newton per pellet while firing at the temperature of 1220 °C~1250 °C in 12 min. The product pellet can be used as high-quality burden for blast furnace to manufacture ferronickel.IntroductionIn recent years, the global stainless steel market was developed exuberantly, which greatly promoted the needs of the basic raw material of stainless steel smelting - metal nickel. Currently nickel sulfide ores are only 40% of global nickel reserves, but offer 60% of all the nickel production. However, with the deficit of resources, the nickel sulfide ore (high grade ore) is depleting, so there is an increasing focus on the utilization of low-grade nickel laterite. Recent research has focused on the wet treatment process to utilize nickel laterite, and less on the use of other technologies [1-8]. The economical and efficient technology relies on the reduction of nickel oxide and part of the iron oxide metal by agglomeration and smelting in blast furnace in China. Some domestic steel companies have adopted this process [9, 10]. Unfortunately a large fraction of fines is generated during the pre-treatment stages and the strength of agglomeration is weakened, which results in low productivity and bad quality of fired pellets. In this study, the process of pelletization of nickel laterite was developed firstly, and some parameters to strengthen the pelletization of nickel laterite have been optimized, and the product pellet can be used to produce stainless steel and ferronickel alloy by blast furnace."

Jan 1, 2011

By D. Kennis

"Union Miniere Precious Metal's (UMPM's) Hoboken Business Unit has a long tradition in complex Pb-Cu metallurgy, focussing on the recovery of precious metals from various types of secondary and recyclable materials. Although the old flow sheet, based on a traditional sinter plant, blast furnace, and lead refinery process was a very complete flow-sheet with the capability of dealing with almost every impurity, the weaknesses became clear:1. old and costly technology,2. too many unit operations,3. too much internal recycling, and4. dependency on concentrates for the sintering process.To maintain the competitiveness of the Hoboken Business Unit, the project ""Smelter 2000"" was born. This project represents a breakthrough in metallurgical processes and technology. A modem smelting technology was chosen together with the development of a new process. A lead-copper process combining lead slag and blister copper production, carried out in an ISASMEL T vessel, was the key to simplifying the Hoboken flowsheet. ISASMEL T smelting technology was chosen for its flexibility towards feed characteristics and process parameters.The new smelter was commissioned at the end of 1997. Although there were a lot of problems due to the high degree of technical innovations in the process, the new smelter came to design capacity within 1 year after start-up. During this period, however, UMPM had, a very difficult time because of the extreme clear-cut nature of going from the old to the new flowsheet.After two and a half years of operation, the new flowsheet has proven to fit with the strategy of UMPM, focussing on treating secondary Pb-Cu materials and a broad range of recyclable feeds such as electronic scrap (E-scrap) and catalysts. Together with the new Precious Metals Plant, efficient logistics, recognised world class sampling practices and a customer-focussed commercial organisation, UMPM Hoboken can definitely be considered reborn."

Jan 1, 2000

By Guo Chang Jiang

In order to improve the IIAZ toughness of X-60 pipe steel, the intragranular ferrite plate (IFP) technology was used. The characteristics of IFP is claimed to be much fine ferrite plates appear inside the original austenite grains. By means of suitable Re, Zr, Ti additions in a bath with a higher initial oxygen potential, a good control of the peak temperature and the cooling rate during welding simulation, one can get a %IFP in volume over 50%, and the toughness gets up from 55 J to 160 J. It was found that the inclusions most effective in nucleating IFP are some deformable complex silicates which either entrap Re, Zr, Ti oxides or contain these elements. The greater the number of the evenly distributed and effectively nucleating inclusions, the more the %IFP in volume, and the finer the microstructure of the HAZ, so the better the relevant toughness. Generally, these silicates bahave as fine spheres along a line. The present authors revealed that these fine spheres result from the remelting of the shuttle- like silicates due to heating in the process of welding simulation. These silicates used to get a higher sulphur capacity, so MnS deposits might be observed on the periphery of the silicates. IFP was proved to be directly rooted in the [Mn] depleting zone which locates beside MnS deposits.

Jan 1, 1997

By J. Priede, G. Gerbeth

"Two different instability mechanisms of electromagnetically levitated bodies are analyzed. The first is due to the virtual coupling between the electric current passing through the magnetic system and the variation of position of the body. This mechanism can result in unstable mass center oscillations of a levitated solid body. Another type of instabilities may occur because of the coupling between the motion and the electric currents induced in the body. This effect can cause a spontaneous rotation of the body setting in as the frequency of the alternating magnetic field exceeds certain critical threshold depending on the configuration of the field. This instability can be suppressed by an axial steady magnetic field of strength comparable to that of the levitating field. 1 IntroductionAn alternating magnetic field interacting with eddy currents induced in a conducting body causes repulsion between the body and the coil generating the field. Besides, the eddy currents provide a contactless heating of the body. In such a way metallic samples can be levitated and melted without a contacting crucible. This technique allows to avoid contamination of the melt with container material and so to achieve a considerable super-cooling of the melt before it solidifies. Nowadays electromagnetic levitation is widely used in material research for measuring of the thermophysical properties of molten metals (2) .It has been observed since early fifties when the first experiments on the electromagnetic levitation were done that under certain circumstances solid levitated samples start to rotate or oscillate [l]. Surface oscillations can appear in addition when the sample is melted. Such phenomena are undesirable because they often result in failure of the levitation. Recently we showed that rotational as well as oscillatory instabilities can have electrodynamic origin related to additional eddy currents induced by motion of the body in an alternating magnetic field [3] , [4].In the first part of the present paper we analyze another possible cause of oscillatory instability due to the coupling between the electric current passing trough the magnetic system with variation of the position of the levitated body. The second part of the paper deals with the origin and suppression of rotational instability in a uniform alternating magnetic field."

Jan 1, 1999

By Ma Lijuan, Zhang Yubing, Wang Bo, Sun Huilan

The effect of lime ratio on phase composition and alumina leaching property of MgO-contained calcium aluminate clinker were investigated by analytical reagent, the XRD analysis of its mechanism was discussed. The results showed that: when the sintering temperature was 1350 ℃, C/A was 1.4, A/S was 1.3 and the content of MgO was 4%, the increase of the C/A promoted the formation of C12A7 and restrained the formation of Q-phase. The alumina-leaching ratio of the clinker (A/S was 1.3) was increased from 74.33% to 91.34% when the content of CaO was 5.21%.

Jan 1, 2015

By Petrus Christiaan Pistorius, Farzin Fatollahi-Fard

The production of titanium oxycarbide – a consumable anode material used in molten-salt processes for electrowinning titanium – from heavy mineral concentrate, such as a high-titania leucoxene and natural rutile is described. The oxycarbide is prepared by carbothermic reduction of the oxide at elevated temperature. Particle size distribution (of the titanium oxide raw material) and temperature have large effects on the kinetics of the reaction, which seem to follow a “shrinking-core” model. It is anticipated that low porosity (in the anode pellets) would be advantageous during electrolysis. Particle size distribution, extent of reaction during carbothermic reduction, and sintering temperature are expected to affect pellet porosity after sintering, and are being tested experimentally.

Jan 1, 2015

By Guangshi Li, Xionggang Lu, Xueliang Xie, Xingli Zou, Yuyang Bian, Hongwei Cheng, Kai Zheng, Changyuan Lu

The corrosion resistance and corroded microstructure of MgO-C refractory in molten slag are investigated by immersion test in muffle furnace at 1600 °C . The microstructure and chemical compositions of the specimens after erosion experiment are characterized by scanning electron microscope (SEM) and energy dispersive X-ray (EDX). The results confirm that the oxidation of graphite is the most important degradation mode of MgO-C refractory. The structure of the refractory material is damaged due to the decrease of graphite, as a result, the periclase substrate reacts with the molten slag directly. The corrosion process is controlled by the dissolution of the refractory materials into slag, low melting point oxides are therefore generated which lead to the damage of MgO-C refractory finally.

Jan 1, 2015

A strategy is presented for a relatively. "low-tech" means for decontamination of streams . containing .low concentrations of toxic metals. Metal ion solutions were . circulate through fluidized beds of activated carbon which support bio-films ?of bacteria .that naturally excrete exopolysaccharides. The attached 'biomass is shown to significantly enhance nickel, cadmium and silver extraction from dilute solutions (5- l00mg/l). By heat treating (at 300º C) the metal/biomass/carbon particles, bio-sorbed silver was subsequently fixed to the carbon surface. This approach to metal decontamination may therefore also provide a route for dispersing and fixing catalytic metal particles over an activated carbon surface.

Jan 1, 1991

By Y. Maeda

Kosaka Smelter is a copper smelter located at the nothern part of Japan? and has been treating. complex sulfide concentrates using flash smelting technology for a long time. The flash smelting technology has an advantage in the point of controllability of matte grade and heat balance in the reaction shaft. But the disadvantage of this process, is that the dust generation ratio is high compared with other smelting process such as injection smelting technology. This reason why is that the flash smelting process is the oxidation process for the fine sulfide concentrates applying flash reaction in the oxygen enriched stream In addition of this disadvantage, the sulfide concentrates contains much volatile impurities is resulted the dust; eneration ratio more. This paper outlines the recent improvement of the flash reaction in the furnace and the behavior of impurities in Kosaka Smelter.

Jan 1, 1998

By Patrick R. Taylor

Sub-micron sized boron carbide powders have been synthesized in a non-transferred arc thermal plasma reactor. Precursors for this synthesis are boric acid or boron oxide powders and methane. The powders produced were characterized in terms of size, shape and purity. Methods to increase the purity of the product were evaluated and included hot water leaching to remove unreacted oxides and controlled temperature, air roasting to remove excess carbon. Theoretical results are also presented on the thermodynamics and mechanisms of the synthesis reactions.

Jan 1, 1994

By Jerold L. Johnson

Remediation of small-arms firing ranges is being investigated by the Naval Civil Engineering Laboratory and the U.S. Bureau of Mines. Scheduled closures of military installations, as well as the management of active ranges, require the development of methodologies for heavy metals removal to prevent their entering the surrounding environment. The impact berms contain high concentrations of metals, and the soil and vegetation surrounding the berms were found to have slightly elevated levels. The heavy metals characterized are in the form of whole bullets, a wide size distribution of free fragments, smeared lead on the surface of the soil grains, and very finely attached particles. Gravity beneficiation can remove liberated metal contamination effectively. Weak acetic acid leaching shows promise in lowering the final metal contamination to allow the ,soil to pass the Environmental Protection Agency's (EPA) Toxicity Characteristic Leaching Procedure (TCLP) criteria.

Jan 1, 1993

By G. L. Hundley, D. N. Nilsen

The U.S. Department of Energy investigated the use of liquid-emulsion membranes (LEM) for the selective removal and recovery of metals such as copper and zinc from mine waste waters. This investigation included field tests of a mobile, pilot plant-scale, continuous-flow LEM system. The system was tested at copper mines with solutions containing from 100 to 1,400 ppm Cu, and at a zinc mine with a solution containing 115 ppm Zn. Typical results from the copper tests were >90% copper recovery, and zinc extraction from waste water also was typically>90%. Although all of these waste waters contained high impurity levels, pure products were produced. On several of these field tests, integrated systems were tested that resulted in recovery of metal by-products, selectiv~ precipitation of iron, and polishing to reach discharge targets for essentially all of the contained metals. In addition, some results are included from laboratory-scale tests.

Jan 1, 2000

By Sheng-li Wu, Guo-liang Zhang, Bo Su

The mineralogical characteristics of iron ores can influence their high temperature sintering performance. In this study, eight iron ore samples from Brazil, Australia, and South Africa were characterized by their chemical composition, mineral types, particle morphology, and gangue dispersity. Meanwhile the influence rules between the mineralogical characteristics and the high temperature characteristics were evaluated and analyzed. The results showed that the effect of SiO2 on assimilation characteristic of iron ores was relatively complex, Al2O3 and LOI of iron ores had negative correlation with assimilation temperature of iron ores, the dense slab-flaky mineral granule restrained to the assimilation characteristics of iron ores; liquid phase of iron ores with high SiO2 content and low Al2O3 content had high fluidity, and the higher dispersity of gangue minerals in iron ores was good to the fluidity of liquid phase.

Jan 1, 2015

By Yuanbo Zhang, Zhaokun Tang, Mingjun Rao, Guanghui Li

The ballability of hematite ore with addition of a certain amount of pulverized anthracite and the induration features of anthracite–containing hematite pellets were studied. The results indicate that adding a certain proportion of anthracite can improve the quality of green pellets as well as the roasting performance of roasted pellets. The suitable mass dosage of anthracite is 1.0%–1.5%. Under the conditions of roasting temperature 1280 oC–1350 oC and roasting time 15 min–20 min, the compressive strength of roasted pellets is found to be more than 2500 N/P. Compared with hematite pellets in the absence of anthracite, the proper induration temperature is diminished by 20 oC, whereas optimal induration temperature range expands by 50 oC, and induration time is shortened by 5 min–10 min. Adding anthracite is an effective measure to improve the pelletization of hematite.

Jan 1, 2015

By T. S. Montgomery

The performance of carbon-magnesia brick in electric arc furnaces (EAF) is interpreted in light of their observed optical microstructures. Features at the bricks' hot faces were protruding periclase grains, metal globules, graphite-metal contacts and linear void patterns. These features were com-pared to similar features previously seen from microstructures of basic oxygen furnace (BOF) refractories. Modes of formation were sought; an attempt was made to interpret their influence related to wear mechanisms.

Jan 1, 1982