Search Documents

By Thomas L. Vandergrift

With the inevitable expansion of homes, businesses, and infrastructure in coal mining regions, the potential for future subsidence above abandoned mines is of increasing concern. Of particular concern are areas underlain by room-and-pillar coal mines. Unlike areas above longwall mines, where total extraction causes subsidence in a predictable and timely manner, subsidence above room-and-pillar mines is difficult to predict and may be active for many decades. As part of a geotechnical assessment of a water pipeline replacement project, NSA Engineering recently performed an evaluation of tong-terns subsidence potential along the proposed alignment due to time¬dependent failure of underlying room-and-pillar workings. The alignment of the replacement pipeline closely follows an existing concrete pipeline, which lies 150 11 to 300 fl above workings that both pre- and post-date the pipeline. Annual surveys along the existing alignment indicate that some subsidence has occurred, primarily from partial pillaring performed in the early 1980's, but that this subsidence is not active. Using the boundary-clement code LAMODEL as the primary analysis tool, NSA followed a three-step approach to estimate future subsidence impacts on the replacement pipeline. First, historical information for the mine was compiled, allowing for calibration of models to actual field conditions. Then, numerical models of workings directly under and adjacent to the proposed alignment were nun, with model input parameters varied until resulting loading patterns matched historical data, and subsidence in the model approximated that measured along survey lines. Finally, time-dependent deterioration of coal pillars was simulated by decreasing the coal strength in the calibrated model until a realistic "worst-case" condition (stability of barriers, but Yielding of production pillars and pillar remnants) was attained. Subsidence from the previous calibrated model was then subtracted from that of the worst case model to estimate future subsidence and related ground movement parameters that slay occur along the proposed alignment. The replacement pipeline design, incorporating couplings capable of withstanding the ground movements predicted, is now being finalized.

Jan 1, 2000

By Gerald I. Finfinger

Identifying the properties of overlying rocks in underground mining operations is important to ensure the appropriate roof support design is used to maintain stability of the mine entries. Recently J. H. Fletcher & Co. developed a monitoring and control system for roof bolters for the underground mining industry. The system records the drilling parameters used during roof bolt drilling and the information can provide insight into the physical properties of the roof strata. The parameters include thrust, rotational speed, torque and velocity and the measurements are collected every 0.1 second during the operation. The drilling parameters were analyzed to determine the application of identifying the strength of rocks being drilled from the measurements. The data was converted into the specific energy of drilling which is a measure of the amount of energy required for removing a given unit of rock during a drilling operation. The laboratory studies completed to date indicate a fairly high correlation between the specific energy of drilling and the unconfined compressive strength of the rocks that were drilled. Additionally, the drilling parameters were shown to be effective for identifying the presence of fractures or bed separations between rock ]avers. The thrust, torque and specific energy of drilling were all good indicators for identifying the fractures or separations. Regardless of the drilling parameters used during the drilling experiments, the location of the fractures were identified, In order to determine the application of the drilling parameters for identifying rout rock properties, two series of experiments were conducted. The first series of experiments used three "manufactured" roof layers that had various rock samples embedded in concrete blocks. The rock samples included three types of sandstone, marble. and argillite. Another concrete block was poured with foam inserts to simulate large bedding separations (2 to 8-in). Two other manufactured blocks were constructed using high-strength concrete with cardboard layers embedded to simulate smaller fractures or bedding separations. The size of the cardboard layers varied from 1/8- to 1-in thick. One of the blocks had the cardboard layers embedded at an inclined angle to determine the effect of the orientation or, the drilling parameters. A series of experiments was conducted with the rotational speed and the penetration rate held constant and the thrust and torque allowed to vary. The information collected from the experiments is used to determine the application of the drilling parameter measurements for identifying rock properties, fractures and bedding separations.

Jan 1, 2000

By Charles D. Albright

FMC built its first angle bolter in 1969. This was a single mast unit which could drill holes for conventional bolts or angle holes for installing roof trusses. From this drill we learned very quickie that the mast design was an important factor to the success or failure of any angle bolter. The first mast installed on this machine (EXHIBIT 1) was fixed in length with endless chain and hydraulic motor feed. It took less than a shift underground to determine that the fixed length was not going to work. The undulating top created conditions where the mast was too long to be positioned at a 450 angle. Several mast designs were tried and discarded before we felt we had the answer to our problems. (EXHIBIT 2} We developed a mast that would extend or retract without moving the position of the drill unit. This allowed the operator to "wedge" the mast between the floor and roof before starting his drill feed. This arrangement worked exceptionally well, but unfortunately the demand, as perceived by our Sales Department, for angle bolters did not materialize. This unit became an "orphan" and was used by many coal mines until it died a natural death. FMC did not decide to re-enter this market again until 1979. At this time many coal producers were contacted to determine what features should he incorporated into a dual mast angle bolter. From this information we were able to arrive at three main areas of concern that we should consider when designing a new machine. 1. Eliminate overturning moment on drill unit. 2. Provide some sort of steel support near roof line to aid in starting a 15° hole. 3. Dual mast units need a method of raising center of mast rotation to facilitate various mining heights and still maintain a 45° angle and proper distance from rib. I would now like to discuss each of these individually. EXHIBIT 3 indicates the overturning moment resulting from the feed cylinder thrust and the reaction of the drill hit against the roof. To eliminate this moment a mast was designed using two feed cylinders mounted in the plane of the drill center line, thus removing all overturning moments on the drill unit carriage. This mast has been used extensively in vertical drilling with no downtime attributed to wear on mast guides and drill unit supports. The cylinders are designed to provide uniform thrust and feed speed throughout the total stroke. For manufacturing and economic reasons, the final mast design on the first drill was not used for this new drill. A drill steel support mounted on the mast, and positioned by a hydraulic cylinder provides the needed guidance near the roof for starting a hole at a 45° angle. (EXHIBIT 4) This support does not surround the drill steel but simple cradles the drill steel for "collaring" the hole. Once the hole is started, the support can he lowered. The support plate is hinged to allow the drill mast to pass. The advantage of having vertical motion of the center of rotation on a dual mast drill is shown in EXHIBIT 5. Following the criteria recommended by Birmingham Bolt Company, the truss bolts should he at a 45° angle and one fifth of the width of the entry from the rib. Therefore, in an entry 20 ft. wide, the hole should be drilled 4 ft. from the rib and at the 45° angle previously mentioned. With the limitations inherent to dual boom drills, that is, the masts cannot pass each other nor can one mast pass the center line of the machine even if the other is positioned out of the way, it is impossible to accommodate much variation in seam height and maintain the recommended criteria. As shown in EXHIBIT 5, a center of rotation 17 inches above the floor will start a hole 4 ft. and 45°angle at a height of 67 inches. Any height above 67 inches

Jan 1, 1982

By Huamin Li

Mine # 8 of Pindingshan Coal Group, Henan Province, China has an annual production 2 million metric tons. But it encounters many problems, e.g. mine layout is complicated, roadway maintenance is difficult, coal and gas outbursts are severe, production cost is high, etc. The major reason was due to the additive effects of abutment pressure interaction of previous mining in D, E, and F seams. At the request of mine management, an in-depth systematic analysis including underground observation, modeling with simulated materials, and photoelastic experimentation was performed to obtain site-specific results which include the dynamic and static influence zones of mining D, E, and F seams, propagation characteristics of abutment pressure in the floor strata, interburden movement caused by undermining, etc.

Jan 1, 2000

By André Vervoort

In coal room and pillar, and pillar extraction panels, the sidewall conditions were investigated based on underground measurements and numerical simulations. Three-dimensional linear elastic models provided a useful and quick prediction of the amount of sidewall spalling. However, more complex constitutive models were required to simulate more accurately the extent of fracturing and its effect on the stress re-distribution. The input parameters of a Mohr-Coulomb model were determined by back-analysis of underground measurements, and the effect of the depth of the workings and the time dependent occcurrence of coal pillar fracturing were analyzed.

Jan 1, 1992

By A. W. Khair

This paper presents an analysis of ground movements recorded from longwall operations in the Northern Appalachian region in West Virginia. The site chosen for the investigation was selected due to varying heights of overburden and topography and was instrumented for both surface and subsurface measurements. The instrumentation areas consisted of two panels covering various sections with unique geologic and topographic features. Instrumentation included surveying monuments and shallow boreholes using an inclinometer for measuring horizontal strata displacements. Vertical strata deformation was monitored utilizing a unique design of the mechanical grouting method. Full length borehole profile extension was measured using Sondex displacement rings in the inclinometer installation. Subsurface displacements, i. e. caving zone, fractured zone, and highly deformed non-fractured zone were identified. The nature of surface disturbances with respect to varying geologic settings were compared, and an attempt was made to simulate final strata caving and bed separation using finite element analysis.

Jan 1, 1987

By S. J. Mitchell

An analysis of bolting reinforcement of several large [approximately 18 m (60 ft) cube] pillars was performed. The many overcoring stress profiles in pillars at the mine were used to produce generalized stress distributions at various stages in pre- and post-failure. A complete stress-deformation curve was estimated from this data. The effect of pillar bolting on the load-deformation behavior was extrapolated from the observed unbolted behavior. Bolting can increase pillar strength by up to 10 percent. The effect of bolting on general mine stability was examined with a shoW computer analysis. The computer model was calibrated against measurements performed at the mine, and produced good agreement between measured and modeled stresses. The analysis indicated that bolting increases the bolted pillar safety factors in the event of additional pillar failure by a small amount (approximately 5 percent). Progressive pillar failure is unlikely, because arching transfers most load from yielding pillars to large unmined abutments rather than to the smaller panel pillars.

Jan 1, 1984

By Ken Barish

Jane Mine of the Keystone Coal Mining Corporation was started in 1962 and is in the Lower Freeport seas located in Armstrong County, Pennsylvania, approximately 45 miles northeast of Pittsburgh. The mine is a slope/shaft complex with the cover ranging from 100 feet at the slope to 450 feet near the back end of the property. The seam height ranges from 48 to 72 inches. A variety of roof conditions have been en¬countered, and an equal variety of roof control systems have been tried with varying degrees of success. Initially, places could be mined as deep as 100 feet without any permanent roof support. After several problems and the advent of the Health and Safety Act of 1969, roof control became more and more prevalent and predominant at the Jane Mine. It started with 4 foot conventional oolts. As the mine progressed in the northeasterly direction, roof conditions changed from the extremely good roof that was encountered initially, to bad roof; and other types of roof support were required. Sixty pound rails and 6 inch 25 pound to the foot steel I-beams were used for supplemental support in long life headings such as belt and track. Resin bolting was done in many areas for long life support due to the deterioration of the shale roof over time. Several areas had to be abandoned because of uncontrollable top.

Jan 1, 1984

By Reha Ozel

The stability in longwall faces depends on the interaction beman the roof strata, face supports and floor strata. The load distribution on the other hand, depends upon relative stiffness of the three supporting elements namely, the coal face, support and gob. Therefore, in defining support requirements, it is particularly important to analyze the strata loading, the face convergence and the controlling mechanism provided by supports. The controlling mechanism however, depends on the type and characteristics of supports used in long- wall faces. The design guidelines presented in this paper have bean developed based on a number of strata control oriented projects carried out in Turkey, load and convergence measurements carried out in 10 longwall faces, in Zonguldak Coal Region, and procedures given in literature. Evaluation of load and convergence measurements, and analyses of face supports were carried out by means of a computer program, called L0NGWAI.L-MEW, developed by the authors. The output of the design analyses include the following: (1) estimation of support capacity for roof supports namely; individual hydraulic props, chock-type power supports and various types of shield supports, and (2) analysis of loading conditions and response of shield support components in terms of stability and structural integrity.

Jan 1, 1990

By Dennis R. Dolinar

A room and pillar coal operation in central Pennsylvania was experiencing roof cutters and long running roof falls caused by high horizontal stresses. The roof conditions created hazards for the miners, and caused several production panels to he abandoned prematurely. The mine requested assistance from the National Institute for Occupational Safety and Health (NIOSH) in applying the "advance and relieve" mining to reduce the affects of the horizontal stress during panel development. The "advance and relieve" plan that was developed called for removing a pillar on one side of the panel as it was being advanced, thus creating a cave. The caving then relieved a portion of the horizontal stress across the panel. Because the horizontal stress direction is key to the success of this method, stress mapping as well as mining experience was used to establish the direction of the horizontal stress. Subsequent field measurements provided an estimate of the stress magnitude. Three panels were mined using this technique, and good roof conditions were achieved in all these panels. Instrumentation was used to monitor the stress changes in the roof created by the cave. Stress relief of over 1.000 psi was measured 120 ft from the cave and to depths of 20 ft into the roof. The lateral extent of the stress relief zone across the panels appears to be about 400 to 500 ft. This case history has provided much insight into the practical application of the "advance and relieve" method discussed in this paper.

Jan 1, 2000

By P. M. Lin

The problem of abandoned mine land (AML) subsidence is getting more severe because abandoned mine lands which used to be located in the remote areas have been gradually developed into suburbs or even urban areas. Abandoned mine subsidence is also becoming more common than before because the time-dependent effect of exposed underground materials. These materials will deteriorate gradually and cause subsidence as time passes. Subsurface conditions of abandoned mines are seldom known to the public. Mine maps are not always available. If the mine mans are available, their accuracy are very - often questionable. In addition, the most common damages to surface structure and ground surface due to mine subsidence can also be created by other non-mining related geological hazards. These factors make the study of abandoned mine subsidence significantly complicated, tedious, and inconclusive. For instance, the cause, time, and amount of surface subsidence can be predicted with relative accuracy during active mining. However, it will be a considerable challenge to do so on abandoned mine subsidence. If abandoned mine subsidence can be predicted in advance, then the damages can be held to a minimum. However, this prediction technique is not yet well developed. Therefore, remedial measures require more attention. In order to have effective remedial measures, the real cause of the damage should be determined first. This paper describes the approach which was employed for the determination of abandoned mine subsidence. A site investigation was made first. According to the information obtained from the site investigation, a hypothesis was set up. Then the instrumentation was used to prove the hypothesis. By going through the procedures for several cases, a guideline which can be used by the inspectors to inspect abandoned mine subsidence will be established.

Jan 1, 1987

By John W. Fredland

Conducting mining operations under a body of Water can create hazardous conditions for miners. The potential for a sudden inrush must be considered and abnormal ground control conditions can be encountered. This paper synopsizes the factors which mine operators should take into account when evaluating whether an inrush may occur. It addresses the applicable Federal regulations and discusses some items which coal operators should consider in applying for a permit, Through collecting and analyzing the pertinent information, the likelihood of encountering problems can be judged. Through proper mine planning, the potential for creating hazardous conditions can be mitigated.

Jan 1, 1982

By Gexin Sun

This paper overviews the recent research progress in predicting cutting performance using fracture mechanics principles. It is emphasised that rock fragmentation due to cutting is mainly a process of chip formation resulting from crack initiation and propagation or crack interaction for multi-tool cutting. This process can be simulated by using the well developed fracture mechanics criteria coupled to numerical methods. Fracture toughness is shown to be an important and useful parameter in quantifying cutting performance and in designing cutting tools. The paper concludes with discussions on the dynamic effects involved in rock cutting processes which should be taken into account for optimum cutting efficiency and tool design.

Jan 1, 1992

By Maleki. Hamid

The U.S. Bureau of Mines implemented an inte¬grated static and geophysical monitoring program in a southern Wyoming mine to study changes in seismic wave propagation properties in roof strata. The purpose was to develop techniques to assess roof stability problems. The work consisted of record¬ing deformation and stress histories and calcu¬lating seismic velocity profiles. In addition. geology and roof conditions were mapped; the in¬struments were initially installed at the develop¬ment face; monitoring continued until the mecha¬nized retreat face retreated within 60 m of the instruments. Mining geometry consisted of a three-¬entry gate system using 5.2-m-wide pillars at depths of 426 m. Results were analyzed using stan¬dard history plots, velocity tomographs, and numer¬ical modeling techniques. Changes in velocity. frequency, amplitude, dynamic elastic modulus, and dynamic Poisson's ratio were related to roof defor¬mation, fracturing, and support requirements. A reduction in seismic velocity of 17 pct occurred after 60 mm of roof deformation following installa¬tion of supplementary support. Static measurements revealed significant dilation in the mine floor, spreading to the pillar and the mine roof. Failure was initiated in the floor as a result of uniform pillar penetration.

Jan 1, 1993

By John P. Dunford

U.S. Bureau of Mines researchers are investigating the ability of mine-wide monitoring systems already in place at many coal operations to provide a direct link between geotechnical instruments and the mine-wide monitoring console on the surface. This paper describes a number of field tests using instruments such as-string potentiometers to measure roof-to-floor closure and bed separation and pressure transducers to monitor pillar loading. The advantages of using existing systems include on-site data collection and analysis, real-time understanding of geological conditions, and long-term data recovery from areas that have become inaccessible to mine personnel. However, because data are generated constantly, large files develop very quickly. In many cases, the data are redundant, such as during times of reduced mining activity or in areas not yet in the vicinity of active mining. To reduce the volume of data, a software program was written that eliminates unnecessary readings and generates a more concise file that can be output to a mine-wide monitoring system, personal computer, or as hard copy.

Jan 1, 1993

By Alan Peacock

Shield supports have been in use in the USA underground mines since 1975, and their development in the intervening time has been progressive and inovative. Specialized techniques are used to optimize their performance in a particular application and to design the component parts.

Jan 1, 1981

By Noor Mohammad

Comprehensive numerical modelling of the subsidence associated with longwall mining in UK Coal Measures strata has been conducted and validated against UK data. The Rock Mass Classification System (RMR) was used as the main basis to derive representative in-situ rock mass properties for stiffness and strength parameters for the numerical modelling input. A Finite Difference Method, Fast Lagrangian Analysis of Continua (FLAC) has been used to design a suitable non¬linear model and simulate the behaviour of the caved zone with a unique modification of the post failure properties within the zone of influence. The established model was validated for different configurations, varying depth, panel width and extraction thickness, in a sensible and realistic range. The Subsidence Engineers Handbook (SEH) and a stress abutment model were used as a validation tool in this respect. The approach developed will be modified for application to a number of different International Coalfields with different geological environments.

Jan 1, 1997

By Bruce K. Hebblewhite

Underground pillar extraction continues to be practiced in Australia in various forms, in spite of the dominance of the longwall method, which accounts for over 90% of underground production. Australia has been a leader in various forms of pillar extraction, particularly since mechanisation was introduced to the industry during the middle of the 20th century. Historical developments have included a range of thick seam mining pillar extraction methods; the widely adopted Wongawilli method; early adoption of the use of mechanized breaker line supports; and a number of more recent partial extraction systems including what is known as rib stripping. Current pillar extraction practice varies from total extraction panels to various forms of partial extraction, driven by either surface subsidence constraints or by underground conditions. This paper reviews a number of different pillar extraction methods and mining layouts, and also highlighting a number of fundamental geotechnical principles which have been found to be critical for safe pillar extraction ? often through lessons learned the hard way, as a result of back analysis of different accident scenarios. These principles include the all-important understanding of the location of the goaf (gob) edge at any point in the operation, and the management of that goaf edge; the impact of geological structures on local and regional stability; the critical importance of extraction lifting sequences; the role of stooks (remnant pillars); and a number of other factors. The paper will also briefly reference the educational and training practices adopted in Australia aimed at the continuous improvement of pillar extraction safety.

Jan 1, 2011

By Ed Mchugh

Recent studies by researchers from the National Institute for Occupational Safety and Health indicate that shear loading contributes significantly to failure of bolts used for rock reinforcement in coal mine roofs. Laboratory tests on 17 bolts were conducted to study the behavior of roof bolts subjected to shear loading over a range of axial bolt loads. Fourteen strain gauges were attached to each bolt to measure axial and bending loads at seven locations along its length. The instrumented bolts were grouted through two high-strength concrete blocks, and axial tension was applied to as much as 75% of yield strength. With the block interface acting as a failure plane, shear loads were applied to the blocks at a constant rate of displacement to the ultimate strength of the bolts. The tests characterized the relationship of axial bolt loads to shear forces across a rock bedding plane and measured the distribution of axial and bending strain along the length of the bolts. These results will improve the selection of roof reinforcement in mine areas where high shear stresses are present, thus improving the safety of miners working in these areas.

Jan 1, 1999

By C. Thomas Blevins

This paper is intended to be a hands on experience account about ground control in a Southern Illinois coal mine. Its aim is to show how a combination of real world mining practices and constraints along with practical engineering theory mesh together to formulate a ground control program in adverse conditions. These conditions - your typical localized slips, splits, rolls, clay intrusions, water, changing types and thicknesses of materials, etc. - being amplified by a very strong horizontal stress field. A review will be made about the formation of the overall ground control plan and to what degree it has been successful. A presentation of the various roof control systems and their component parts, how these systems were developed, and the theory behind them will be made. The pointing out of some of the flaws that we found in the components, installations, and/or theory will be part of this presentation. A brief look at some of the efforts in the following items will be made: quality control of the roof control products; using the computer to help keep track of roof control information and soliciting help from various universities, governmental agencies and consultants to give different perspectives to the problem.

Jan 1, 1984