Search Documents

By Yoshiaki Fujii

Displacement Discontinuity Method (DDM), which was originally developed by Crouch,S.L., is a powerful tool to calculate mechanical disturbances due to tabular excavations. Three topics on DDM applications to strata control problems in Japanese deep coal mines are described. First, is numerical simulation of microseismicity induced by longwall mining in Horonai Coal Mine. Microseismicity in the mine had been monitored by a mine-wide seismic array. Location of microseismic events and intensity of seismicity were well simulated. In the simulation procedure based on DDM, first, zones where a failure condition is satisfied by the advance of mining are detected. Then, the seismic moments, which indicate the intensity of seismicity, at the failure zones are evaluated. Second, is prediction of the shaft damage due to mining in Sumitomo Akabira Colliery. In this mine, the limit angle of the shaft pillar was changed from 600 to 800 to increase the amount of minable coal volume without increasing mining depth. Displacement of the shaft axis has been measured to assess the damage due to mining around the shaft pillar. In the calculation based on DDM, a fault intersecting the shaft and the ground surface are considered. Observed and predicted displacement of the shaft axis agreed well. Third, is the roadway deformation in Taiheiyo Coal Mine. Attainable maximum stress for a roadway was calculated considering three faults intersecting the roadway. It was realized that the roadway's convergence is related to the calculated stress by simple equations.

Jan 1, 1992

By Joel Bradley, Kot Unrug, Kyle Perry, Mark Klimek

"A West Kentucky mine operation in No. 11 seam, encountered floor heave, due to the localized increase of the thickness in the fireclay mine floor. Floor heave has overridden seals installed in two mined out panels. The third seal’s location was planned for isolating that area from the Mains. A plan of support has been developed to prevent repetition of the floor heave and related problems outby the seals. The applied ground control measures were successful. An attempt of a 3D numerical modeling was made, that it would match the observed behavior of the mine floor and could be used as a design tool in similar conditions. In the paper described are sequence of events, a mitigation ground control system applied, and the first stage of numerical modeling.IntroductionWest Kentucky coal mine operation in the No. 11 seam has approached an area where the fireclay floor thickness increases to about 5 ft. Delayed floor heave has been observed. In the first sealed area (Panel KK), floor heave has overridden the seals and has begun to progress outby. This could not be allowed at the new seal location PP described in this paper because such override would affect the mains. Previously numbers of standing support systems were used, but their effectiveness was not satisfactory as is illustrated in Figure 1, Figure 2, and Figure 3. Therefore, with sealing of the next area approaching, mine management was looking for a better solution that would eliminate the problem. In that stage, our team looked closely at the geology and strength of roof and floor, as well as the characteristics of ground failure around the seal at the first site. The technical literature has been searched as well Haramy et al. 1986 Hsiung and Peng 1987, Peng 2008, Santos & Bieniawski 1987. This led to the identification of factors responsible for the ground failure. It has been determined that increased fireclay thickness from typically less than 2 ft to about 5 ft, when compared to the previously mined parts of reserve, and the strong limestone strata just above the immediate roof composed of 2 ft of black shale, created conditions of failure. It appeared that, when pillars were punching into the mine floor, the strong roof did not break but was bending, exerting high pressure on outby pillars, causing rib failures and closure. This is a similar mechanism to a strong roof affecting longwall shields. The remedial action planned was additional support."

Jan 1, 2015

By Michael Trevits

The NIOSH Lake Lynn Laboratory (LLL) is a unique research facility, located about 50 miles southeast of Pittsburgh, Pennsylvania, that is designed to provide a full-scale mining environment for testing and evaluation of mine health and safety technologies. The LLL occupies more than 400 acres and is composed of surface test and training areas and an underground mine. The Lake Lynn Experimental Mine (LLEM) was built at an abandoned commercial limestone quarry where surface mining ceased in the late 1960's. Later, new underground development was constructed to simulate modern-day coal mining scenarios; including room-and-pillar and longwall mining layouts. In January 1994, a sinkhole opened southeast of the No. 4 Portal of the LLEM and since then, the area of the underground failure and surface deformation has continued to expand and now includes several interconnected sinkholes. A concern developed that the overburden instability could expand and affect the structural integrity of the nearby highwall and the No. 4 Portal. It was unsafe to conduct a detailed underground survey of the mine in this area because the mine roof conditions near the No. 4 Portal had deteriorated significantly. It was decided to investigate the overburden conditions near the No. 4 Portal using ground penetrating radar (GPR). A GPR survey grid was located along an access road that passes over the top of the portal. To delineate the mine conditions near the portal, antennas whose frequency spectra produced pulses centered near 100- and 200-MHz were used. The results of the GPR survey suggests that the overburden rock units appear to be laterally consistent to a depth of about 15-ft. Below that point, the overburden appears to be significantly disturbed and it was hypothesized that this area contains a large roof fall. A follow-up ground truth survey of the mine roof conditions was conducted from the mouth of the portal. It is concluded that the observations and measurements made from the radar records appear to be correct as a large roof fall was observed and measured from the mine portal area.

Jan 1, 2005

By Francis S. Kendorski

Rock reinforcement has been in widespread use and generally has been accepted in underground mining and tunneling since the 1950s. The first rock reinforcement technologies employed were mechanical anchors such as split wedges or expansion shells with 5/8-inch-diameter steel bolts. Failures occurred in weak strata which provided poor anchorage or in ground with corrosive waters. Friction rock fixtures consisting of relatively thin-walled tubes have been in use for about 15 to 20 years. While generally performing adequately, longevity problems have developed from corrosion in water bearing ground Longevity of rock reinforcement is much enhanced with grouted bolts. Portland-cement-grouted rock reinforcement has been in use since the mid-1950s, primarily in funneling and other civil engineering underground construction. Tests of decades-old installations have revealed few problems except in ground with aggressive waters. Polyester-resin-grouted rock reinforcement was introduced in the United states to musing in the late 1960s and to tunneling in the early 1970s. Experience from 30 years of resin-grouted bolt installations and field tests have identified longevity problems associated with degradation of steel reinforcing bars, but in generally unusual situations. Improvements continue in resin chemistries, packaging, corrosion protection, grout quantities, and mixing and distribution in the drilled hole to achieve long-term performance. Specific case histories cited with resin- or Portland-cement-grouted rock reinforcement longevity or performance problems, upon close examination, reveal that the causes of the problems were qualify control procedures being inadequate and not in accordance with good practice. Manufacturers' recommendations and engineering specifications, if followed in the field, and with competent inspection and supervision, would have prevented must, if not all, reported longevity or performance difficulties.

Jan 1, 2000

By John L. Ellenberger

The National Institute for Occupational Safety and Health (NIOSH) has continued the research role of the former U.S. Bureau of Mines to develop techniques that will reduce the hazards in the mining work place associated with coal bumps. Current research focuses on both analyzing historical seismic data from bump-prone operations and utilizing a mine-wide seismic network to investigate the exact strata failure mechanics associated with bump-prone geology. The anticipated outcome of this research will be reduced bump incidences through advanced engineering concepts and designs which implement the new understanding of strata behavior. The analysis of the historic seismic data consists of correlating observed mining seismicity with the geologic and geometric parameters at the sites. The primary seismic parameters are the timing, location and magnitude of a recorded seismic event. These parameters are correlated with such mining parameters as: the overburden, the size of the immediate gob, the size of the district gob area, etc. This detailed analysis of historical seismic data has provided an informative quantifiable relationship between many of the specific mining parameters and the induced seismicity. The second aspect of the coal bump research is the instrumentation of an appropriate field site to determine the main roof, floor, and gob behavior associated with hump behavior. The chosen field site is a deep-cover longwall mine with competent geology in a historically bump-prone area. The primary field instrumentation is a three-dimensional, full-waveform, seismic array with both surface and underground sensors surrounding an active multi-panel district. The purpose of this seismic array is to determine the timing, the exact location, and the mechanism (tensile fracture, bedding plane slip. etc.) of the failure of the strata surrounding the active and multi¬panel gobs. The preliminary results presented in this paper help to define the strata failure areas around the longwall panel.

Jan 1, 2000

By E. Bane Kroeger

For many years, researchers around the world have been investigating coal pillar stability. Many have focused on trying to optimize the size of the pillars by examining stable and failed pillars in underground coal mines. For mines that are already in operation or companies that are opening a new mine adjacent to an existing mine where the pillar dimensions and stability can easily be determined, this is the preferred technique. However, when a new mine is planned for an area where there has been relatively little mining, then samples of the coal need to be drilled and tested for strength. Because of the fractured nature of coal, this lab testing is often problematic and may often yield poor results because of the limited size and number of samples that can be obtained from the core. To remedy this problem, research was conducted in the labs at SIUC to determine if improvements could be made when optimizing the size of pillars for underground coal mining in Illinois. Through a greater understanding of the relationship between dimensions and strengths of coal samples tested in the lab, it was hoped the in situ strength of coal pillars could be determined with greater accuracy. This could allow the extraction ratio to be increased and more of the coal resources in Illinois recovered without impacting the safety of the mine workers. Many different agencies around the world have published recommended minimum numbers of samples for strength determination based on the size of the coal samples. For two inch cubes, uniaxial testing of at least seven samples is recommended and this minimum number decreases to four when testing four inch cubes. However, the laboratory testing of coal from two seams thus far has suggested this number should be almost doubled to accurately determine the coal strength. Testing also showed there is a pronounced decrease in the variation in the strength of the samples tested as the dimensions of the sample were increased. From the testing results thus far, it is recommended that a sample size versus strength curve be constructed for every coal seam for Illinois. Creating such a curve will better determine both the minimum number of samples and minimum sample dimensions for that seam or region of a particular scam. A second set of tests were conducted in the laboratory to determine the increase in strength with reduction in height for samples with the same width and length. In Illinois, typical pillar dimensions are 40 to 80 feet (12.2 to 24.4 m) wide and long, with coal thickness varying from about 4 to 9 feet (1.22 to 2.74 m). This provides width/height ratios ranging from 4.5 to 17.5. Coal samples having width/height ratios ranging from 0.5 to 13 have been tested thus far. As with most pillar design formulae, the strength of the Murphysboro coal versus width/height ratio was linear and closely matched shape factors published by other researchers. The laboratory testing thus far has identified three factors that affect the strength of laboratory samples, the number of discontinuities, the angles of critical discontinuities, and the shape of the samples. The factor that probably had the most pronounced effect on the strength of the coal samples was the angle of critical discontinuities. This testing has confirmed that there is still a gap that needs to be bridged between the strength obtained from laboratory testing and the in situ coal strength predicted.

Jan 1, 2004

By Jialin Xu

Bed separations position, size, development characteristics and their influence factors have been analyzed in-depth by experimental and theoretical methods. The results show that the key strata determine the creation, development and space-time distribution of the overburden bed separations and fractures. Based on the dynamic growth principle during the two-stage development of bed separations, the theory of section-grouting for the overburden bed separation space and the O-ring theory for the pressure-relieved methane drainage are proposed. The technique has been applied in some coal mines in China to reduce surface subsidence and for methane drainage. Keywords: rock strata movements; key stratum; bed separation; bed separation grouting; pressure-relieved methane drainage

Jan 1, 2003

By T. P. Mucho

Mine roof failure due to excessive horizontal stress has been recognized as a major cause of hazardous roof conditions in some mines. Stress measurements gathered by the U.S. Bureau of Mines (USBM) at 24 different eastern mines show horizontal stress to be typically 2 to 3 times as great as vertical stress. The focus of current Bureau work is to develop detailed design parameters to assess and control the effects of horizontal stress. To facilitate the recognition of horizontal stress effects and to easily determine principal stress direction without resorting to cumbersome, expensive, and time consuming field measurements, the Bureau has developed a stress mapping methodology. Stress recognition and direction determination are required to successfully employ a number of control strategies such as mine layout, mining sequences, and support optimization to control the effects of horizontal stress, thereby increasing the safety of U.S. coal mines. This approach has been used in other major coal producing countries, most notably Australia and the UK, and has greatly enhanced the safety of their mines (1). This paper discusses horizontal stress, directional based control techniques, and provides guidelines for the use of the stress mapping technique. A case study of a mine where the technique has been used is also presented.

Jan 1, 1994

By W. A. Cincilla

The use of resin-grouted rock anchors continues to gain popularity in underground wall mines in the United States. It is estimated that during 1985, more than 30% and as many as 35% of all roof bolts used employed sane from of resin anchor. The so-called 'combination' bolting systems, which generally utilize a resin pint-anchor, have also found increased application. This increased application is particularly true in poor ground, where more 'traditional' support measures have performed poorly. Virtually all resin bolts in use today in U.S. mines employ cartridge-type delivery systems, which in general, have produced good results under a variety of conditions. However, a host of inconsistent and sometimes uncontrollable variables may significantly alter the optimum bolt performance. These variables have been identified and are well documented in the literature (Snyder, et al., 1979; Kwitoweki and Wade, 1980; Serbcusek and Signer, 1985). The beau of Mines, Denver Research Center (DRC) conducted a major research project aimed at investigating the effects of selected aspects of installation procedures on resin-bolt performance. One objective of the project was to establish anchorage criteria for full column resin bolts installed in actual mining conditions. This piper describes the results of a particular study which focused on quantifying, through field tests, possible reductions in bolt anchorage due to installation of less-than optimum resin columns. These columns might result from losses of resin to surrounding strata, or non-compliance with recommended installation procedures. Over 1000 resin bolts having grout columns ranging from 12 inches up to 48 inches (full column) were installed and pull-tested at 13 underground test sites located in a total of 11 mines (Fig. 1). Four basic roof-rock types were included: shale, top coal, sandstone, and limestone. The majority of the bolts employed 3/4-in-diameter, 48-in-long, type 40 rebar having a minimum '~ated' yield point of 17,600 lb (8.8 tons). Actual yield strength may vary by manufacturer.

Jan 1, 1986

By I. L. Follington

A breaker line support (BLS) monitoring system, BLSmon, has been designed and constructed by the CSIRO and installed and commissioned at Laleham No.1 Colliery, Queensland. This system was designed to record hydraulic leg pressure and canopy position measurements and relay these, in real time, to the surface. The system has shown itself to be capable of operating on the BLSs without any adverse affect on production, Analysis of the results of the monitoring exercise has shown that rate of change of leg pressures on the BLSs could be used as an aid in the prediction of adverse mining conditions. Under favourable mining conditions the supports were observed to initially unload from the set pressure, this unloading reduced with time and by the end of a typical lift cycle had either ceased or reversed slightly. This behaviour was considered to be due to one of four possible causes, these being; the compaction of floor debris, and/or compaction of the floor, and/or crushing of the roof and /or support creep. The actual cause can only be determined through detailed monitoring of both roof and support convergence. However observational data would suggest that compaction of debris and softened floor material beneath the supports was the most likely cause. The few positive loading rates recorded under these conditions were of short duration and occurred towards the end of individual lifts. Where mining conditions were unfavourable the negative rates of change of pressure, unloading of the support, were reduced throughout a lift, in both duration and magnitude, when compared with favourable mining conditions. Over the same period the positive rates of change were observed to be greater. The rate of change of loading and convergence can be utilised to identify the onset of instability in the lift area. However, before this facility can be utilised by the mine for the reliable prediction of instability more monitored data and sophisticated processing techniques are required. A mechanism has been postulated for the deformation behaviour of the roof and pillars in a mechanised pillar extraction operation from the continuously monitored data, observational data and results of previous studies. The 7 m wide fenders were observed to yield under abutment stresses before lifting commenced. The stability of these fenders throughout the lifting sequence was considered to be dependant upon the magnitude of their post peak load carrying capability. This is influenced by the post peak stiffness and the extent of roof lowering in the vicinity of the fender. Difficulties with fender extraction occurred where remnant coal left standing in the goaf caused uncaved goat to bridge to the mined fender. Difficulties were also experienced where sub-vertical jointing occurred in the roof of the split reducing it's ability to bridge effectively. Despite the relatively short monitoring period, the potential role and application of continuous monitoring in advancing understanding of the rock mass response to mechanised pillar extraction operations has been demonstrated. This understanding now requires enhancement and shows great potential for aiding the optimisation of mechanised pillar extraction operations.

Jan 1, 1992

By Jimin Su, Enguang Zhu, Kangning Zhang, Yang Li

"The effect of interburden on overlying strata movement during the mining of a lower group coal seam is still a challenge in China. Based on the multiple coal seams in western China, numerical simulation and field tests are applied to study the interburden and overburden movement during the undermining process. This study focuses on the impact of the thickness and structure of the interburden, the proportion of hard rock, and the ratio of the overburden thickness to interburden thickness (OB/IB). In this paper, four typical underground coal mines are simulated for lower seam longwall mining with different interburden parameters. The results indicate that the ratio of the overburden thickness to the interburden thickness is not the dominant actor for multiple seam longwall mining, especially in the mines in western China,which feature shallow depth. The thick and hard interburden could strongly affect the lower coal seam mining process. INTRODUCTION The project background is based on four typical underground coal mines in western China.The information on the overburden and interburden is shown in Table 1. Different overburden to interburden thickness (OB/IB) (Ellenberger, 2009) values of the four coal mines are also studied: 6.2 in Bulianta coal mine, 7.2 in Kaida coal mine, 8.2 in Shigetai coal mine, and 9.4 in Halagou coal mine. The proportions of hard rock in the interburden of the four coal mines are also different: 0% in Kaida coal mine, 70% in Shigetai coal mine, 80% in Bulianta coal mine, and 100% in Halagou coal mine. To be specific: the thickness of interburden are listed as follows: 7m in Halagou coal mine, 6m in Kaida coal mine, 10m in Shigetai coal mine, 28m in Bulianta coal mine. The depth of the upper coal seam are: 66m in Halagou coal mine, 54m in Kaida coal mine, 79m in Shigetai coal mine, 182m in Bulianta coal mine. NUMERICAL SIMULATION UDEC 4.0 is applied in this paper to analyse the overlying strata movement and the interburden failure.(Liu, 2007) This is based on mining in the lower coal seam under the mined-out upper coal seam (Majdi, 2012, Morsy, 2006)."

Jan 1, 2017

By Xuexin Ding, Weijie Wei, Jinwang Zhang, Yi Chen, Shengli Yang

"Many ultra-thick coal seams exist in Xinjiang and the northern part of the Inner Mongolia. These coal seams are more than 30-40m thick. This kind of the thick coal seam is too difficult to extract in one slice, so the top-coal caving longwall mining method was designed for this purpose. In order to study the movement characteristics of the overburden strata and the development of the ""three zones"" in ultra-thick coal seams, the physical and numerical simulations were carried out based on the in-site condition of Baiyinhua coal mine. The result shows that, when extracting the upper part of the l 5m thick coal seams, the first weighting interval was 50-58m and the periodic weighting interval was I 8-20m. The caving zone, fractured zone and bending and sinking zone were 38m, 92m, and 50m respectively in height. The fractured zone height increased with the advancing distance of the face, but in some localities, a ladder-like distribution due to the periodic weighting existed. When extracting the lower part of the 25m thick coal seams, the roof was extremely broken and the collapse range of overlying strata continued to increase in irregular form.INTRODUCTIONThe thick coal seams occupy 44 percent of coal reserves in China and account for 45 percent of the gross domestic coal production. There are three main methods for extracting the thick coal seams: sublevel mining, large height mining, and longwall top-coal caving (LTCC) (Wang, 2009). Due to the rapid development of LTCC in the past two decades, it has become the most extensively used mining method. It possesses the advantages of high-production, high-efficiency, low development ratio, and low-cost (Yang, Zhang, Chen, and Zhengyang, 2016; Wang and Zhang, 2015). Baiyinhua coal mine's coal reserves are full of uniformly distributed thick coal seams, with the minable thickness of the main coal seam between 25 to 40m, i.e. the main coal seam is an ultra-thick coal seam. Sublevel longwall top-coal caving (SLTCC) which is an efficient method for extracting the ultrathick coal seams has led to multiple disturbances Xie, Chen, and Wang, 1999; Singh and Singh, 1999; Xie, Chang, and Yang, 2009. Therefore, using the case of Baiyinhua coal mine, the movement features of overburden strata and development characteristics of the three zones in ultra-thick coal seams were studied by physical and numerical simulations (Qian, et al, 2003; Qian, 1994)."

Jan 1, 2016

By David Hill

"End of panel longwall face recovery is almost certainly the most involved recurring geotechnical problem faced by operators, with major loss potential should problems occur. The paper presents Australian experiences and updates the outcomes of an industry sponsored research project on the geotechnical issues associated with conventional longwall recoveries.A number of critical features of the geotechnical environment, support design and mining geometry have a pronounced impact on ground control during face recovery. A model of roof behaviour at the take-off point has been developed and validated. Key geotechnical issues include low roof competency, an adverse weighting environment, geological structure, horizontal stress concentrations at the gate ends and the capacity and. integrity of the shields. All of these are identifiable either at the support design stage or, at worst, prior to the start of powered support removal, which is the critical stage of the recovery process.Key aspects of the geometry and process are the ability to maintain powered support resistance during bolt-up and recovery, the direction of shield removal, the impact of chutes and the speed of the shield removal process.The author presents case studies that illustrate these issues and the associated ground behavior.INTRODUCTIONEnd of panel face recovery is almost certainly the most involved recurring geotechnical problem faced by operators, with major loss potential should problems occur. However, unlike most geotechnical aspects of coal mining, very little research has historically been undertaken on the issue of conventional longwall recoveries. This is in marked contrast to the design of pre-driven recovery rooms, an issue which has attracted considerable research interest (Thomas, 2008). In 2006, Strata Engineering completed an Australian industry (ACARP) sponsored research project aimed at defining and minimising the geotechnical threats during longwall face recovery (Strata Engineering, 2006). The research project had the overall objective of developing guidelines for the specification of ground control strategies, so as to minimise the likely geotechnical threats relating to the safety, operational costs and production delays associated with the recovery of a longwall face."

Jan 1, 2010

By Brian Daniels, James Farroni

"Draw rock (small rock that forms/falls when bolting the roof and/or rib) is the cause of numerous injuries annually. These injuries result in lost work hours and low morale. The report below explains how ""Mine Safe Draw Rock Shields"" (Pans) are used in an underground operation. This report will chronicle the application of these pans in a Southern West Virginia coal mine along with testing data that measures their effectiveness. Since the introduction of these pans in 2002 the amount of reportable accidents relating to draw rock has decreased by 80%. The report below reinforces that perimeter contact is critical to the performance of these pans. In addition the strength of these products at the perimeter will determine their effectiveness. The results of the testing data outlined in this paper, along with the physical records at the study mine, confirm that the use of pans has significantly reduced draw rock falls at this facility.BACKGROUNDSupplemental support is defined as ground control that is used in addition to required support in an underground mine. Some examples of supplemental support are:• Pans• Mesh/Geogrid• Mats• Half Headers• Boards• ChannelA typical roof condition that warrants the use of pans is when loose small rock is dislodged while bolting. If the top is very scaly (loose, thin rock) additional supplemental support can be used in conjunction with pans such as mesh or geogrid (See Figure 1). Pans will provide protection where used and approximately 12 in (250 mm) out from perimeter. This is achieved by contact with a surface which will put scale in tension up to 12 in (250 mm) from perimeter of pan.INTRODUCTIONThe ease of applying a roof support system is critical to effectively operating a deep mine. Figure 2 shows how a pan is installed in conjunction with a roof bolt and bearing plate. The Mine Safety and Health Administration (MSHA) requires that supplemental support cannot decrease the performance of required support. The goal of using all supplemental support is to provide additional safety for the miner which equates to increased productivity.The ability of skin control products to contact a surface is the single most critical characteristic (Figure 3 and Figure 4). If the material does not contact the surface it cannot be effective. Therefore, the flexibility, design and proper installation of the products are critical in determining their effectiveness. Figure 5 shows the proper installation of the roof pan.To reiterate, all skin control must be applied in conjunction with a roof bolt and ASTM approved bearing plate as shown in Figure 4."

Jan 1, 2010

By N. P. Kripakov

This paper presents a brief overview of current bump mechanics theories and pillar design methodologies, and relates these concepts to experiences at two mines located in a north-central Utah coalfield where different pillar designs were used to control mountain bumps. Experiences gained at the first mine demonstrated the successful implementation of a two-entry, 9.8 m (32 ft)-wide, yield-pillar design. A U.S. Bureau of Mines field study quantified the timing of chain pillar yielding and resulting load transfer from the gateroad. In-mine pillar response, although apparently sensitive to site-specific conditions, compared favorably to estimates derived using two yield-pillar design methods. A second study conducted at another mine located in the same district, but subjected to different geologic conditions, documents the unsuccessful attempts to employ progressively narrower three-entry pillar designs based on successes achieved at the first mine site. This second mine never achieved a true yield-pillar design. Use of pillar widths ranging between 9.1 m (30 ft) and 27.4 m (90 ft) always resulted in violent bumps in the tailgate pillars. The pillars were either too large to yield, or too small to support peak operational loads. Hypothetical gateroad systems were evaluated using both analytical and empirical approaches for configurations comprised of two rows of conventional pillars, and systems incorporating both yield and abutment pillars. Analysis concluded that yield pillars less than 6.1 m (20 ft) wide and abutment pillars ranging between 30.5 m (100 ft) and 39.6 m (130 ft) square would be required to achieve a stable gateroad design. However, results of a field study conducted on a two-entry, 36.6 m (120 ft)-wide abutment pillar concluded that abutment pressures from the first panel overrode the pillar, and that a still larger pillar may be required to preclude bumps in the tailgate during second panel mining. Without the benefit of a demonstrated in-mine success, it is not clear which design would ensure elimination of gateroad bumps.

Jan 1, 1992

By Yang Li

For the study of overburden movement in longwall mining of shallow coal seams, most scholars merely consider the thickness of bedrock and top soils. In this paper, the overburden movement in longwall mining of shallow coal seams with thin top soils and key strata group was studied. By using numerical simulation, the development of fractures in the overburden was analyzed for different ratios of panel width to depth (W/D) and depth to mining height. The results show that the overburden movement changed with the variation of mining height, panel width and depth under the specific geological conditions. It also explain how different overburden disturbance structures, such as ?three zones? (caved, fractured, and continuous deformation zones), ?two zones?(caved and fractured zones) or ?steps-like collapse? are formed under different mining conditions. The results broaden the vision for research on overburden movement in longwall mining of shallow coal seams.

Jan 1, 2014

By Christopher Mark

Despite more than half a century of experience with roof bolting, no design method has received wide acceptance. To begin to improve this situation, National Institute for Occupational Safety and Health (NIOSH) conducted a statistical study of roof bolt performance at a number of mines throughout the U.S. Case histories were collected from 37 mines with a variety of roof bolt types and patterns in a wide range of geologic environments. Performance was measured in terms of the number of roof falls that occurred per 10,000 ft of drivage. The study found that roof falls are rare when the roof is strong and the stress is low, even with light roof bolting patterns. The focus of this paper is on the more difficult conditions, where the roof is weaker and/or the stress is higher. Analysis of the results led to guidelines that can be used to make preliminary estimates of the required bolt length, capacity, and pattern. The guidelines are based on the depth of cover (which correlates with stress) and the roof quality (measured by the Coal Mine Roof Rating (CMRR), and the intersection span. Another contribution is a formula for estimating the horizontal stress level in the eastern U.S. coalfields as a function of the depth of cover. The design guidelines are currently being implemented into a computer program called Analysis of Roof Bolt Systems (ARBS).

Jan 1, 2001

By Thomas P. Mucho

To document the performance of mine roof and roof support systems the U.S. Bureau of Mines (IJSBM) has been installing instrumentation at selected sites in U.S. coal mines. Much of this support and roof instrumentation has been installed in high stress conditions to maximize differences in performance. Summarized in this paper are the results of four such site investigations. The roof geology at the four sites is quite different and is quantified using the USBM's Coal Mine &f Rating (CMRR). The studies included detailed measurements of roof movement using multi-point extensometers, as well as measurements and monitoring of bolt loading. The investigations include developmental loading and abutment loading from longwall and room-and-pillar mining operations. Some of the issues examined are the effect of the horizontal stress field, the effect of installed tension (torque-tension versus resin bolts), the effect of reduced annulus bolt holes, and the differences between similar bolts supplied by different manufacturers.

Jan 1, 1995

By Yongping Wu

The steeply dipping coal seams in this paper refer to those with the angle of inclination ranging from 35° to 55°. The reserves of the steep coal seams account for approximately 15%~20% of the total coal reserves in China. In the past 12 years, the top-coal caving mining method had been used to mine the steeply dipping thick (11.5-16.4 ft or 3.5-5.0m) coal seams. However, the mining process of top coal caving is complex with low recovery rate and nearly 30% of coal was wasted. Those problems can be solved by using the single pass large mining height (11.5-16.4 ft or 3.5-5.0m) method. But the movement of the overlying strata around the mining face area of large mining height is complex and it is hard to control the stability of ?rock-shield support? system. Therefore, field measurement, numerical simulation and physical (similarity material) simulation methods were used simultaneously to analyze the strata movement, roof structure and rock-shield support interaction characteristics. The results indicate that strata movement, which is the same as mining the steeply dipping seams with conventional mining heights, is asymmetrical about the dipping direction of the face; deformation, failures, and movement of the surrounding rocks are more intense; the roof weighting interval decreases; the weighting intensity increases significantly; and face sloughage occurs frequently. In the gob, the space for sliding and rolling of the roof increases; the broken main roof tends to form an anti-dip pile structure; the backfilling and compactness of broken roof increase at the lower portion of the face, thereby inducing significant unbalance in stress distribution between the upper and lower portions of the face. The overlying strata above the face form a multi-level step structure. The characteristics of contact and loading of roof-shield support system are more complex. The range of shield load variation is larger, and interaction between shield supports occurs frequently. Anti-toppling and anti-sliding devices at the face become more difficult to implement. The research results provide a theoretical basis for the mining practices in the steeply dipping thick seams with a large mining height. The practice in panel 25221 of 2130 coal mine indicates that the accident rates have been greatly reduced and good technical and economic benefits have bee realized.

Jan 1, 2014

By Anthony T. Iannacchione

This study, funded by the Appalachian Research Initiative for Environmental Science (ARIES), examines how mine layout, mining method, and geology interacted to allow water from the Grove No.1 mine pool to discharge into local surface waters. Federal and State regulations prohibit the discharge of acid or iron-producing waters from underground coal mines. Mining companies design barriers around their operations to prevent mine waters from discharging to the surface. The Grove No.1 represents one mine where these designs proved inadequate. Unique geologic conditions at the Grove No.1 mine pool, combined with retreat room-and-pillar mining, contributed to a discharge that required passive water treatment.

Jan 1, 2013