Search Documents

By Anthony G. Fonseca

About 45% to 50% of the coal mined in the United States passes through coal preparation plants. East of the Mississippi River, this number increases to about 75% to 80%. Although the cost for coal preparation is worthwhile to some, the coal industry faces the challenges of continuing downward pressure on the price of coal and the impact of new environmental regulations. Coal preparation is an effective process that achieves 75% to 80% ash reduction, 15% to 80% trace element reduction and 85% to 90% Btu recovery. It is less effective for pyrite reduction (35% to 70%) and on-line operating time (40% to 60%). It also suffers from obsolete control systems. In coal preparation, raw coal is modified to a more preferred form to enable its use. The methods used to achieve this modification must be cost-effective and appropriate to the raw coal, the scale of production and the end-user requirements.

Jan 1, 1995

By E. G. Hoover

In the mid-I 970s the rallying cry sent out by the aggregate trade associations to aggregate operators was to come to Washington and help design national legislation mandating reclamation of pits and quarries. This collective effort paid off in that aggregate operators were able to assist in the design of "livable" legislation; however, the coal mining industry took some very hard hits. A principal argument used by the aggregate industry was that relatively small parcels of land are impacted, the operations are located in or near urban areas to serve in the development of that immediate area, and are of many years duration; whereas, coal strip mines disturb many acres, are of short duration, and whose products may have world or nationwide utilization. Historically, developments in reclamation are tied closely to the regulatory systems that have been created to control environmental effects of mining. Since reclamation generally results in a cost incurred after the stone, sand and gravel has been mined and does not add to the inherent value of the mineral, there was little incentive in the past for mine operators to reclaim the land. In 1977, the Surface Mining Control and Reclamation Act (SMCRA) became the law for coal mine operators. The law states that, among other provisions, reclamation must "restore the land affected to a condition capable of supporting the uses which it was capable of supporting prior to any mining, or higher or better uses". It is of interest to note that years before the initiation of legislation leading to SMCRA twenty-eight states already had reclamation regulations that covered virtually all minerals. The scope of performance standards found in the state reclamation regulations included slope stabilization, grading, revegetation, neutralization of toxic materials, visual screening, waste disposal, control of drainage, and other sources of pollution and erosion. Environmental legislation and the consequent regulations came about because the public perceived that private industry did not properly value environmental quality and as a result the government became the policeman.

Jan 1, 1998

By D. C. Ridenour

The pressure system of ventilation with large diameter bore holes has been very effective in the ventilation of two gaseous mines, the Olga No. 1 and No. 2 Mines in McDowell County, West Virginia. The No. 4 Pocahontas Coal Seam on the Olga property lies 580 feet below the valleys. The seam is very gaseous as well as dry and dusty, which makes good ventilation all the more essential. Irregular and often extensive areas of the coal seam have been replaced with impervious shales and sandstones in "Fault" or "Want" areas. The replacement materials have sealed the methane in the coal seam and thus increased the quantity of gas that must be handled as mining is done. Often the No. 5 Pocahontas Seam comes down to meet the No. 4 Seam at the Faults and considerable methane is sometimes released from the upper seam. The factors mentioned, together with the irregular and unpredictable lateral shape' of the faults, result in long narrow stringers of coal that are very gaseous and difficult to mine. So far as the Olga Coal Company is concerned, the most effective ventilation under the conditions outlined has been the use of large diameter bore holes with a pressure ventilation system. The ventilation of a mine can be accomplished in two fundamental ways. The mine atmosphere maybe reduced below atmospheric pressure by an exhaust fan; or it may be raised above atmospheric pressure by a pressure fan. In either case, the coursing of the air is so planned as to have the haulage and traveling ways on intake air. While the majority of the coal mines in the United States, no doubt, use the exhaust system of ventilation, there are several advantages of the pressure system which are extremely beneficial.

Jan 1, 1960

By B. Caines

Much of the mining industry in North America is in a crisis state. Host producers are operating at production levels well below capacity, some have been merged or sold, while others have been mothballed or closed permanently. For many of us still operating, the future is uncertain. Despite the many cutbacks and closures, there is still an abundant supply of minerals in the world market and there is almost no hope for any relief on price pressures on most mineral commodities in the near future. The Iron Ore Company of Canada (IOC)operates an iron ore mine, a concentrator and a pellet plant known as the Carol Project located in Labrador City, Newfoundland. This concentrator and the pellet plant have the annual capacity to produce 20 million and 10 million tons respectfully. A company owned and operated railway links this operation with the dock terminal facilities in Sept Iles, Quebec.

Jan 1, 1987

By Benjamin C. B. Hsieh

Many processes in the hydrometallurgical and chemical industries require the separation of dissolved material from suspended solids. Counter current decantation (CCD) with thickeners is one of the methods generally used. The process engineer needs a quick and accurate CCD calculation method. Several theoretical 1-12 CCD calculation methods are available in the literature . The simultaneous 1, 2 equation method for a complex circuit as used would take too long to solve the problems. Approximate equation method1 is not accurate and is for simple cases only. A shortcut method developed by Counselman3 contains no mathematical equation, and thus is not suitable for computer programming. Based on Counselman's method, Woody4 derived two simple equations in terms of percent soluble loss for two typical examples. Scandrett5 included a term for mixing in his formulas. This mixing efficiency was defined by Murphree6. Another method which depends on making volume calculations instead of using weights is presented by Mastin8 and Cahalan9. None of these methods is related to dissolution and pre¬cipitation reactions. Chen 10,11 demonstrated his methods for counter current leaching. His results are calculated from the general solution of a derived linear difference equation for constant underflow, and from the solution of a derived non-linear Ricatti difference equation for variable underflow. This paper concerns derivation of a general equation for CCD washing with provisions for adding and withdrawing the streams, and for leaching (dissolution) or precipitation reactions. These equations take several forms depending on the input information available. A set of simplified equations for continuous counter current washing and leaching is derived for determining:

Jan 1, 1972

The Sage Mill Project w approved by Santa Fe Pacific Gold Corporation's Board of Directors in October 1994. The Sage Mill Project included a pressure oxidation plant designed and constructed to process refractory carbonaceous ore using fine grinding/autoclaving technology developed specifically to treat Twin Creeks ore. The project was constructed in two phases. The first phase was put into operation on May 5, 1997, just hours before the transfer of ownership to Newmont Gold Company occurred. The second phase started in October 1997. This paper reviews schedule, costs, scope changes, and methodology used on the project that spanned almost five years from project definition through commercial operation.

Jan 1, 1999

By Katherine Hynard, Colin Eustace

Suboptimal decisions introduced during the mine planning process are generally a consequence of both a myopic view of planning objectives as well as time and resources available to convert longer-term plans into execution plans. Erosion of strategic mine plan value in conversion to execution plans is likely to amount to billions of dollars each year. When integrated with operations data feeds, simulation and optimization tools can be used to preserve the value in the strategic mine plan. Optimization models are capable of both automating production of execution plans and improving performance. This reduces the manual burden of revising plans while improving alignment with long-term production objectives. Simulation models can also support the process of developing effective execution plans by providing forward visibility of mine operations performance. They can also be used to test the robustness of optimized execution plans and response to operational variability and disturbances.

May 1, 2025

By A. Ersoy, M. D. Waller

Because of a shortage of diamonds for the drilling industry in the 1970s, efforts were made to develop synthetic diamonds. The resulting development of polycrystalline diamond compacts (PDC) enabled the evolution of a new generation of rotary-drilling drag bits. Bits based on PDC cutters were very successful in drilling soft, abrasive and medium strength rocks. However, because of their thermal instability, they failed rapidly when drilling hard rocks. Thermally stable diamond (TSD) was then developed for hard-rock drilling. The rate of penetration (ROP) and bit life significantly influence the drilling cost. The ROP and the life of the TSD bits or cutters are affected by a number of complex factors. However, in laboratory testing and infield operations, the principal factors that need to be considered in predicting drilling and wear rates are bit design characteristics, bit operating parameters and the characteristics of the penetrated rock. These characteristics are comprehensively reviewed for both laboratory and field drilling results using TSD bits. Optimization of these parameters increases the drilling rate, prolongs the bit life and reduces the drilling cost.

Jan 1, 1998

By A. Uribe-Salas, J. A. Finch, B. J. Huls

Gas holdup profiles in the collection zones of a pilot flotation column (0.91 m x 13.5 m) and a laboratory flotation column (0.057 m x 9.5 m) operated with air and water only were determined from pressure measurements. The profiles were determined discretely and continuously. For the pilot column, a minimum distance between pressure measurements was necessary to give reliable results. For the laboratory column, a third-degree polynomial fit to the pressure vs. height data was required. Water manometers proved to be less sensitive to sensor and process noise than pressure transducers. The profiles showed that gas holdup approximately doubled over a height of 8 to 10 m. The profiles were not linear, and the gradient increased towards the top of the column, especially for gas rates greater than 1 cm/s. The profiles cannot be predicted by a simple bubble expansion model. The implications of this new finding of a significant gas holdup increase with height in the collection zone on various aspects of flotation column design and operation are discussed.

Jan 1, 1996

By Péter Siklósi, János Zámbó, Károly Solymár

It is fundamentally important to evaluate bauxites in a realistic, commercial way on the basis of the processing technology both for the supply of existing alumina plants and for the designing of new ones. The evaluation system developped by ALUTERV-FKI consists of chemical, mineralogical, texture and technological testing. The commercial value of bauxites is basically determined by their available alumina content and the caustic soda consumption required for their processing. However, their contaminants have to be taken into consideration, too. The commercial value of bauxites also depends on the processing technology and their possibly unfavourable chemical and mineralogical composition can be /at least partially/ compensated by R&D efforts. The selection of the optimum processing technology and the effects of further developing the same are demonstrated on monohydrate bauxites containing goethite and carbonates. Some of the technological solutions /desilication or deironing of bauxites, hydrothermal treatment of the digestion residue / make at the same time possible the complex processing of the bauxites, the profitable utilization of their main components.

Jan 1, 1984

By Richard R. Klimpel

The author was the banquet speaker at the 48th Annual MPD meeting, sponsored by the SME Colorado Minerals Processing Section, May 14-16, 1998, in Colorado Springs, CO. Here are his remarks. It has been an exciting experience to have spent 34 years involved with the process of generating patented technology eventually leading to commercialization. In today's terminology, this process is called technology transfer. I have had the unusual experience of being involved doing basic research as an inventor while also being responsible for managing new product development and commercialization. In addition, I worked for 31 years before my retirement for a large research-oriented company, The Dow Chemical Co. In 1995, the company spent more than $1 billion dollars on research and development. The last three years of my career have been spent working with a research-oriented university, The University of Florida. And I have worked as a consultant helping several companies to optimize their products and processes. It is on this cumulative experience base that the preparation of this article is based.

Jan 1, 1998

By Thomas M. Hanna, John W. Anthony, Lee C. Atkinson

Ground water can pose major engineering and environmental problems to the new generation of large, deep gold mines currently being developed throughout the world. It is important that the potential magnitude of these problems be assessed early in the planning of such projects and that any necessary dewatering and environmental remediation programs be designed at least preliminarily in the feasibility stage. The assessment should begin with acquisition of hydrogeologic data during exploration drilling and be followed by carefully designed and analyzed aquifer tests. Once a sufficiently detailed conceptual hydrogeologic model has been defined, state-of-the-art numerical models should be used to estimate ground-water inflows to proposed pits and underground openings, to design and evaluate the potential effects of various dewatering schemes, to define specific environmental impacts, and to predict pore pressures in highwalls relative to slope stability. The modeling results will indicate which method(s) of dewatering will be most effective both technically and economically. If wells are used, it is imperative that they be as hydraulically efficient as possible. There are new methods of drilling and completing dewatering wells that can help assure maximum efficiency.

Jan 1, 1989

By Gunter Fauth

The setting of tasks for the process control of coal cleaning, and in this connection the requirements for instrumentation can be classified into the following three fields: - Monitoring the operation of individual units, or process steps, - Control of units or process steps, - Control of the entire coal cleaning process with the intention of optimizing the operation and the profitability of the process. Instrumentation is affected by the type of cleaning processes. For introduction Figure 1 shows the simplified flow sheet of coal preparation which is usual in the German Ruhr District and in which desirable places for the measurement of ash, moisture and sulfur content are marked. The preparation plant is supplied with run-of-mine coal from the shaft via a homogenization facility. In a first step of primary classifying the raw feed coal is screened at about 10 mm. The raw coarse coal ( = 10 mm) is sorted by jig washers or heavy-medium separators. the raw fine coal (< 10 mm) at first is pneumatically sized at about 0.5 to 0.75 mm. The fines, the aspirated dust, are a finished partial product which will be added to the final metallurgical or steam coal. The material 10 to 0.75 mm subsequently is sorted in fine coal jigs and dewatered in centrifuges. The sludge obtained with the wet cleaning processes is dewatered in thickeners and fed to the flotation. Concentrate and tailings are dewatered by filters or bowl centrifuges and by chamber filter presses or belt filter presses, respectively. The partial products coarse coal, fine coal, flotation concentrate, aspirated dust, and middlings are blended to result in the sellable products metallurgical and steam coal.

Jan 1, 1984

By [Miroslaw] M. Hajdasinsk

The identification of the real internal rates of return (IRR&apos;s) of a project is essential for its economic evaluation. The existing methods for the calculation of IRR&apos;s are both cumbersome and unreliable, mainly because of their inability to effectively isolate the real IRR&apos;s and incapability of discovering multiple IRR&apos;s of even multiplicity. In this paper, a concept of the &apos;cash flow pattern tree used for isolation of the real IRR&apos;s of a project is presented. This concept, combined with the Sturm procedure for counting the real distinct zeros of a polynomial within a specified interval, leads to the development of a method and computer program for isolation and calculation of the real IRR&apos;s of a project. The method examines whether or not real IRR&apos;s exist, and if they do, isolates them within bounded and narrow intervals in a mathematically founded way. The isolated IRR&apos;s, whether simple or multiple, are subsequently calculated either directly or by means of an appropriate approximation procedure. Numerical examples assist the development of the method and the corresponding computer algorithm. Because any Net Present Value treated as a function of interest rate can easily be transformed into a polynomial, the method presented also constitutes a method for finding the real zeros of a polynomial.

Jan 1, 1986

By M. Li, W. R. Reed, J. P. Rider, J. D. Potts

"The National Institute for Occupational Safety and Health (NIOSH) has recently developed a series of validated models utilizing computational fluid dynamics (CFD) to study the effects of air-blocking shelves on airflows and respirable dust distribution associated with medium-sized surface blasthole drill shrouds as part of a dry dust collector system. Using validated CFD models, three different air-blocking shelves were included in this study: a 15.2-cm (6-in.) wide shelf; a 7.6-cm (3-in.) wide shelf; and a 7.6-cm (3-in.) wide shelf at four different shelf heights. In addition, the dust-collector-to-bailing airflow ratios of 1.75:1, 1.5:1, 1.25:1, and 1:1 were evaluated for the 15.2-cm (6-in.) wide air-blocking shelf. This paper describes the methodology used to develop the CFD models. The effects of air-blocking shelves and dust-collector-to-bailing airflow ratios were identified by the study, and problem regions were revealed under certain conditions. The simulation results could be used for future development of dust control methods, particularly to address respirable silica dust, for a surface mine blasthole drill shroud.INTRODUCTION Surface blasthole drilling can generate considerable amounts of respirable silica dust. These high dust concentrations can be exacerbated by the high silica content as drilling cuts through silica-bearing materials such as sandstone and shale, causing overexposures for miners to respirable silica dust. These overexposures can lead to silicosis, an occupational lung disease that has no cure and is often fatal. A review of the Mine Safety and Health Administration (MSHA) respirable silica dust sample database from 2010 to 2016 for metal/nonmetal mining shows the following overexposure rates for occupations related to blasthole drilling: • 14.1% of rotary air drillers were overexposed to respirable silica dust (22 out of 156 samples) • 5.8% of rotary drillers were overexposed to respirable silica dust (9 out of 155 samples) • 7.3% of drill helpers were overexposed to respirable silica dust (3 out of 41 samples) • 7.5% of blaster/shotfirer were overexposed to respirable silica dust (3 out of 40 samples) Of significant interest is an x-ray surveillance study recently completed under the NIOSH Enhanced Coal Workers’ Health Surveillance Program (ECWHSP). This program offered free chest radiographs to surface coal miners in 16 states. Pneumoconiosis was found among 2.0% of the 2,328 screened miners with at least 1 year of mining tenure. Twelve miners had radiographic changes consistent with progressive massive fibrosis, and 9 of these 12 miners reported no underground mining tenure. All but 1 of the 9 miners worked at occupations that were in the vicinity of blasthole drilling, either as a driller, blaster, or blast crew member [1]."

Jan 1, 2018

By M. Li, W. R. Reed, J. P. Rider, J. D. Potts

The National Institute for Occupational Safety and Health (NIOSH) has recently developed a series of validated models utilizing computational fluid dynamics (CFD) to study the effects of air-blocking shelves on airflows and respirable dust distribution associated with medium-sized surface blasthole drill shrouds as part of a dry dust collector system. Using validated CFD models, three different air-blocking shelves were included in this study: a 15.2-cm (6-in.) wide shelf; a 7.6-cm (3-in.) wide shelf; and a 7.6-cm (3-in.) wide shelf at four different shelf heights. In addition, the dust-collector-to-bailing airflow ratios of 1.75:1, 1.5:1, 1.25:1, and 1:1 were evaluated for the 15.2-cm (6-in.) wide air-blocking shelf. This paper describes the methodology used to develop the CFD models. The effects of air-blocking shelves and dust-collector-to-bailing airflow ratios were identified by the study, and problem regions were revealed under certain conditions. The simulation results could be used for future development of dust control methods, particularly to address respirable silica dust, for a surface mine blasthole drill shroud. INTRODUCTION Surface blasthole drilling can generate considerable amounts of respirable silica dust. These high dust concentrations can be exacerbated by the high silica content as drilling cuts through silica-bearing materials such as sandstone and shale, causing overexposures for miners to respirable silica dust. These overexposures can lead to silicosis, an occupational lung disease that has no cure and is often fatal. A review of the Mine Safety and Health Administration (MSHA) respirable silica dust sample database from 2010 to 2016 for metal/nonmetal mining shows the following overexposure rates for occupations related to blasthole drilling: • 14.1% of rotary air drillers were overexposed to respirable silica dust (22 out of 156 samples) • 5.8% of rotary drillers were overexposed to respirable silica dust (9 out of 155 samples) • 7.3% of drill helpers were overexposed to respirable silica dust (3 out of 41 samples) • 7.5% of blaster/shotfirer were overexposed to respirable silica dust (3 out of 40 samples) Of significant interest is an x-ray surveillance study recently completed under the NIOSH Enhanced Coal Workers’ Health Surveillance Program (ECWHSP). This program offered free chest radiographs to surface coal miners in 16 states. Pneumoconiosis was found among 2.0% of the 2,328 screened miners with at least 1 year of mining tenure. Twelve miners had radiographic changes consistent with progressive massive fibrosis, and 9 of these 12 miners reported no underground mining tenure. All but 1 of the 9 miners worked at occupations that were in the vicinity of blasthole drilling, either as a driller, blaster, or blast crew member [1].

Jan 1, 2019

By Scott Brien, O&apos

Cyclones have become standard unit operations in mineral processing for both dewatering mineral slurries and for making separations at given particle sizes. Conventional cyclones are normally able to make moderately sharp cuts. However, the limited ability to control water flow out of the apex means that cyclones have difficulty handling fluctuations in feed. Underflow-regulated cyclones are cyclones with a rubber boot attached to the underflow. This boot acts as a non-return valve and restricts flow out of the apex of a cyclone. Normally, this type of restriction on a cyclone causes severe difficulties in cyclone operation. However, by adding a siphon arm to the overflow, water flow can be controlled. The siphon arm creates a vacuum that reduces or eliminates the air core, permitting better control of the ratio of water flow out of the overflow and underflow. A Linatex-developed underflow-regulated cyclone was compared to a conventional cyclone for its ability to dewater a sand slurry. The underflow-regulated cyclone produced slurries with solids contents as high as 80% in the underflow. Conventional cyclones produced lower solids content in the underflow under similar conditions.

Jan 1, 1997

By R. W. Barbaro, J. M. Mutrnansky

This paper presents a nonlinear integer goal programming model that optimizes a mineral production schedule while considering the penalties and bonuses based on quality variations in the final product. It involves five coal quality goals plus a profit objective in its formulation and uses the weighting method of goal programming for a solution. The goals to be sought involve the sulfur, ash, heat content, moisture content, and ash softening temperature of the blended coal product. The model is linear in its handling of most of these goals but uses a piecewise linear integer formulation for the sulfur and heat content bonus and penalty schedule. The model is applicable to any mineral product blended from several different sources and subject to a varying price dependent on blended product quality or qualities. However, it seems to be most pertinent to optimizing production schedules for coal deliveries to power plants. Accordingly, the model is applied to a hypothetical coal production problem where multiple coal mines are operated to supply a final blended product to a power plant. In this example, the price paid for the coal is assumed to be a function of five of the most important coal qualities. The problem is solved as a direct function of the coal supply contract, thus removing the necessity of determining the weighting coefficients on a subjective basis.

Jan 1, 1987

By Venkata S. Vutukuri

Assuming a number of discrete leakage paths and treating the airflow through leaky duct line as a series-parallel combination of airflows along the duct and through leakage paths, exact solutions for auxiliary ventilation problems can be obtained. A computer program "SEGMENT&apos;&apos; has been written to solve problems using this method. However, most of the investigators have treated the duct lines with a uniformly distributed leakage and many have derived formulas assuming various boundary conditions and levels of simplification for the design of a simple auxiliary ventilation system An appraisal of accuracy of the various formulas has been conducted using the results from the program "SEGMENT&apos; as benchmark and the formulas which give accurate results have been identified. The ranges of application for all the formulas have also been determined for 5 %error.

Jan 1, 1993

By Patrick A. Ley

Maintaining, managing and manipulating large quantities of geologic data can be a very costly and time-consuming process. The use of computer-based methods can provide some relief to the problems of editing, displaying, and interpreting spatial geological data. ENCORE is a system designed specifically for coal orebody modeling and reserve esitmation where the geologic data is stored on a large mainframe computer and is accessed from a local work station for editing, manipulating, and producing various reports and high-quality engineering maps. The ENCORE system was designed for use by the geologist or mining engineer with little or no computer background and, additionally, it was designed to provide the geologist or mining engineer enough flexibility to be able to select the appropriate methodology for the orebody being analyzed. The various analysis tools incorporated into ENCORE can significantly increase the professional&apos;s productivity without burdening he or she with the need to understand the details of the internal computer language.

Jan 1, 1982