Search Documents

By D. A. Dahlstrom

Since the initiation of continuous vacuum filtration over a half a century ago, control of the performance of these units has been largely in the hands of the plant operators, Obviously there has been the introduction of variable speed drives, adjustable speed feed slurry agitation, vacuum control, etc. However, control of , filtration rate, cake moisture content, dissolved solids recovery by cake washing and dryness of solids where thermal drying is practiced is primarily up to the operators judgment and the settings he imposes on the controls he regulates, - filter cycle time, submergence, vacuum level, filter medium condition, wash water- rate, and other such factors. While this may seem to indicate that good operators are a paramount necessity, and certainly always desirable, a considerably more vital factor is a properly designed filter and filter station for the particular application. With improper design, highly skilled operator control will still leave much to be desired in the way of process performance. On the other hand, with correct design and application, the operator can easily and quickly control normal plant surges and quality variations within the flow sheet. Due to the growing complexity and inter dependency between the various processing steps in the modern flow sheet as well as the rising costs of capital investment, labor, maintenance, and losses involved with off quality product or insufficient recovery, automatic or inherent performance control of many of the unit operations within the metallurgical mill must be achieved. Continuous filtration should and can be susceptible to such control. However, as every instrument engineer knows, before control and automation can be achieved, a basic understanding of the operation is mandatory. This is primarily due to three factors. First, as in so many control applications, it may not be possible or feasible to measure the factor that it is desired to control. Thus, secondary variables that influence the major factor are substituted for control purposes. Secondly, it is always desirable to take advantage of any ?self-regulation? within the operation being performed on the equipment. In so doing, not only will automatic control be facilitated, but instrumentation is minimized while experiencing most efficient operation. Finally, automatic control is not a cure-all for improper process and equipment design and application. Hanging instruments on such an operation can be compared to constructing a sizable building on sand, Results will be disappointing.

Jan 1, 1960

By J. R. Sturgul

Computer simulation models of working mines can be a great benefit to mining engineers. Such models have been used in mine planning (how many trucks-shovels to have, when to add new equipment, etc.) and mine design (should a dispatch system be purchased, where is the optimum location, for mine equipment, etc.). A simulation model can be thought of as a dynamic representation of the mine. It can be easily changed to reflect a variety of situations. A major problem for the engineer is how to present the results of the simulation study. This has now been overcome by means of animation to present the results of the simulation. The main simulation languages in use for discrete system simulation are SLAM, SIMAN and GPSS/H. Each has animation with SLAMSYSTEM for SLAM, CINEMA for SIMAN and PROOF for GPSS/H. Animation with SLAM and CINEMA have been on the market for several years whereas PROOF is a relative newcomer and has features not found in other animation software. This discussion will be confined to PROOF. Some of the comments will apply to all simulation and animation software.

Jan 1, 1995

By K. Norris

The Amax Gold Guanaco mine is located in the Atacama Desert, approximately 260 km southeast of Antofagasta, Chile. The 6,000 tpd leach operation produces approximately 90,000 oz of gold, and 360,000 oz of silver per year. Production began in 1987, and the operation has been managed by Amax Gold since 1992. The mine has been plagued in the past by high operating costs and low production. Several significant changes have been made to the operations which have resulted in lower costs and higher operating efficiencies. A review of these changes is presented herein.

Jan 1, 1997

By Jurgens PE Hamman, Faisal Putra, Hadnaltias Alpeki, Willem de Beer

The Deep Ore Zone mine is the third lift of caving at PT Freeport Indonesia’s East Ertsberg Skarn System. An increasing trend in seismicity along the northern boundary of the DOZ cave, as well as the northern fringes of the DOZ production and infrastructure levels, was taken as indicative of an interaction between the approaching DMLZ cave and the DOZ subsidence zone. Seismicity trends and locations indicated a reducing crown pillar and an associated stress increase along these DOZ excavations, as well as the regional area along the DOZ cave boundaries. Although rockbursts were not identified as an immediate hazard, seismic shakedown was a highly probable hazard in the case of remote large (≥3.0) seismic events. An evaluation process, as described in the Canadian Rockburst Support Handbook (1996), was followed to identify and quantify the various parameters that could contribute to a shakedown evaluation. A shakedown assessment, based on the Peak Particle Velocities scaling relation, was conducted to assess the current installed ground support systems along the northern fringes and the fixed facilities of the DOZ mine. The range in ground support systems were mostly due to different geotechnical environments. The load–deformation characteristics of these support systems were evaluated to determine the support capacity and compared to the potential support demand under varying shakedown conditions. Shakedown hazard maps were compiled to indicate the installed ground support system’s vulnerability to seismic shaking. Based on this information, areas were divided into zones indicating whether they were sufficiently supported, additional support was required, access was to be restricted, and / or they were to be abandoned. Mine management utilised these hazard maps to strategize actions for the various operational zones within the DOZ, including the fixed facilities. This paper briefly describes the derivation of the PPV scaling relationship. Seismic and geological data for the DMLZ – DOZ interaction areas were evaluated to determine the likely source of large events. Subsequent larger events and their effects are shown to assess the veracity of the magnitude and PPV estimates, as well as the effectiveness and appropriateness of the ground support systems.

Apr 26, 2022

By Terrence Chatwin, Michael Sweeney, Steve Accardo

Sutter Gold Venture excavated an exploration decline into a mineralized zone in the Sutter Creek gold mining district. Delays in obtaining the conditional-use permit resulted in 7 to 10 million gallons of water accumulation in the decline containing elevated dissolved arsenic. Sutter received a permit to land apply the water after reducing the arsenic concentration to 0.05 mg/L. Initially the water was treated by co- precipitation arsenic with ferric hydroxide. Operational difficulties of this treatment system resulted in Sutter pursuing alternative treatment methods. The activated alumina adsorpting was selected due to its flexibility and ease of operation. Operating and maintenance data and costs will be presented.

Jan 1, 1995

By E. L. Bohnet

The purpose of this paper is to translate a mining company's "Corporate Objectives" into usable and practical guidelines for long term mine design and production scheduling. These guidelines are required to ensure that both operating and development properties are designed and economically ranked on the same basis, and with the "current" Corporate Objectives in mind. Secondly, if both management and mining engineers have a better understanding of the cause and effect of corporate policies, then penalties and risks associated with various Corporate Objectives can be put into better perspective for management. Corporate Objectives, relative to usable guidelines for either short and/or long term mine planning, could be defined as one or more of the following four objectives: 1) Maximize the recovery of the economic portion of the defined geologic resources, and hence, maximize total non-discounted project cash flows and profits (most common approach in mine design), 2) Maximize the Net Present Value (NPV) of the after-tax cash flows from each existing or proposed project, either on an individual basis or in concert with other projects, including downstream processing facilities (primary method used to judge relative investment merit of a proposed development or operating concept), 3) Limit short and long term capital expenditures to a defined ceiling, 4) Maximize product output for the existing facilities in the short term, or conversely, keep commodity production at a constant level for a series of years.

Jan 1, 1994

By J. H. Gasper

The overall success of steep slope (>20°) contour mining is dependent upon many factors. The major factor is the selection of the mining method that best suits the premining site conditions both environmentally and economically. These conditions can be divided into three major categories: 1) Geometric Conditions --machine limitations, slope stability restrictions, erosion capacity, among others; 2) Physical Conditions--material properties, rock strengths, diggability, driving surfaces, among others; 3) Chemical Conditions --acid/base relationships, blending or selective placement of overburden, among others. This paper incorporates these conditions through conceptually modeling compliance oriented contour mining methods; in particular Haulback methods, utilizing: 1) the Front-End Loader (FEL)/Truck; 2) Tractor Scrapers; and 3) Combined FEL-Truck/Scraper. Engineering analyses including machine selection, sequencing, ease of varying production rates, slope requirements (for stability and running surfaces), drainage requirements and many others can be performed after the geometric constraints dictated by in-situ conditions and regulatory requirements have been conceptualized. Once all generalized geometries have been established, reduction to idealized three-dimensional views is achieved. These are then reduced to two-dimensional symbolic models, mainly plan views, but also elevations and sections. Equipment activities and operations are then conveniently overlayed. Without this simple two-dimensional reduction, technology transfer remains awkward and non-analytical.

Jan 1, 1991

By A. I. Kogut

Impurity minerals in fluorspar ores and concentrates from a deposit in Southern Africa have been studied by reflected light, transmitted light, and cathodoluminescence microscopy. The principal impurities are quartz, calcite, aegirine, apatite, ankerite, magnetite, goethite, and synchysite [Ca(La,Ce,Nd)(CO3)2F]. Cathodoluminescence microscopy was found to be very useful in studying the character of the fluorite and especially for recognizing the presence of apatite and calcite impurities. Fluorite exhibits blue, calcite shows yellow, and apatite has white, light purple, and pink cathodoluminescence. The cathodoluminescent character of apatite varies with its geological environment and position in the orebody. The results of this microscopic study show that phosphorus present in fluorite concentrates occurs principally in binary locked apatite-fluorite particles. Successive fluorite cleaner concentrates contain progressively smaller amounts of locked apatite-fluorite particles. Free apatite has been effectively partitioned to the final tailings.

Jan 1, 1995

By Sheldon P. Wimpfen

Sand and gravel has been, and will continue to be, our principal construction material. Most of us are familiar with the patterns of past growth. Today we will examine the present status of this vital industry. We shall also attempt to look into the future to see where it is going and to evaluate the constraints that are being imposed. Natural aggregates are among the lowest in value of all bulk industrial minerals. From the processing point of view, sand and gravel production is relatively simple since the products are sized materials obtained from a deposit of satisfactory physical soundness. They can be used either loose or bound to provide bulk, strength, or protection. One of the main uses of coarse aggregate is in concrete as a filling material. As a general rule, the coarse aggregate constitutes about three-quarters of the volume of concrete. The other main use for aggregate is as a roadstone or roadbase to provide protective and stabilizing bulk beneath the road surface. Also it is used in a mixture with petroleum products as the wearing course on top. The sand and gravel industry is geographically widespread. In general, the output of operations is directly proportional to the amount of construction in any area. A wide variety of other aggregates compete with sand and gravel, including crushed stone, blast-furnace slag, clinker, and artificial and natural lightweight materials.

Jan 1, 1972

By H. F. Haller, H. C. Pattison

The research program described in this paper is sponsored by the Advanced Research Projects Agency of the Department of Defense and monitored by the Bureau of Mines, United States Department of the Interior. PROGRAM DEVELOPMENT While Holmes & Narver is better known in other fields, the company has been active in many phases of underground excavation for over twenty years. In the 1950's, H&N participated in design and construction of nearly twenty miles of waste disposal tunnels in Southern California. As Architect-Engineer for the Atomic Energy Commission, we had design and management responsibility for many miles of tunnels and for thousands of feet of exploration and big hole drilling, from coast to coast in the States, and for gas well completions and exploration drilling for the Navy and the National Science Foundation from Pt. Barrow to Byrd Station in Antarctica. In my ten years with the company, we contributed to the development of big hole drilling techniques at a number of sites and analyzed the capability of boring machines for many of the tunnel projects. In a 1965 engineering study of a hundred miles of vehicular tunnels in rock under New York City, we investigated

Jan 1, 1997

By G. R. Erdman

The industrial mineral filler plant of the Gouverneur Tale Company is equipped with a good dust collection system installed long before the recent popularization of environmental pollution. Credit for this fact is due to the foresight of Mr. R. S. McClellan, Project Manager and subsequent Vice President and General Manager of Gouverneur Talc, who recently retired as Vice President Engineering of the parent organization, the R. T. Vanderbilt Company. Also instrumental in the early stages of plant operation and the solution of start-up problems was J. A. Gustin who is now an engineering consultant located in Martinsville, Va. Credit is most certainly due to the late R. T. Vanderbilt, the company's founder, who favored and approved the investment in the necessary facilities that were far ahead of all competitors in the industry at that time.

Jan 1, 1972

By J. A. Cole

The mill project at Lone Tree was commissioned in October, 1993, followed by the commissioning of the autoclave pressure oxidation circuit in February, 1994. Discussion of the first year of milling operations at Lone Tree is presented. The mill is currently operating above the design rate of 2,267 mt/d (2,500 st/d). Both phases of the start-up were essentially trouble free. The few problems that were encountered and the respective solutions are addressed.

Jan 1, 1995

By A. B. Cortes

This research work discusses the development of a two-dimensional model that represents the flow that occurs in the inlet section of hydrocyclones. The governing equations are the two-dimensional, unsteady, incompressible Navier-Stokes equations in cylindrical polar coordinates with primitive variable formulations. In this approach, no assumptions have been made other than independence in the axial direction. The full two-dimensional Navier-Stokes equation in the r-a plane is used. The commonly used simplifying assumption of axisymmetry is not used. A numerical technique based on a newly developed spectral-difference method is used to solve the equations. The spectral-difference method is a multi-domain, and multi-dimensional extension of the Jacobi polynomial collocation technique. The computational grid for the inlet section is composed of 25 sub-domains which result from five partitions in the angular direction and five partitions in the radial direction. Several test cases are used to validate the appropriateness of the numerical model.

Jan 1, 1995

By R. K. Rajamani

The theoretical model based on fluid mechanics, in conjunction with the laser-Doppler velocimetry (LDV) measurements, elucidate the size-classification mechanisms in an industrial hydrocyclone. The model has no adjustable parameters and involves solving the Navier-Stokes equations to predict the liquid-phase velocities. The spatial-concentration gradients were determined considering the particle phase in the Lagrangian frame and the classification curve was determined by balancing the forces acting on the particle. The force balance requires liquid velocities, which in turn depend on the local volumetric concentration of the particles. Hence, complete modeling work involves coupling both the concentration and liquid-phase velocity calculations until convergence is reached. Finally, the experimental and predicted classification curves were presented for 250-mm hydrocyclone operating at high-percent solids.

Jan 1, 1994

By J. V. G. Middleton

The paper gives a comprehensive review of the design considerations which determined the choice of the milling plant, a description of the plant and comment on the operating experience to date. Operating experience will include inter alia a description of the mill liners installed with subsequent changes due to wear patterns, the mill inlet sealing arrangement, steel ball addition, mill outlet sump design, cyclone feed pump liner wear patterns and comment on the efficiency of the linear screens for wood chip and tramp removal. Finally a view on future trends in South African milling practice with respect to type and size of plant.

Jan 1, 1989

By A. J. Lewis, P. J. Hutcheson, M. E. Robertson, P. A. Moir, K. M. Barfoot

With the content of gold and platinum in the vast majority of ore deposits typically averaging 6 parts per million and less, the accurate and precise measurement of these metals in samples of ore and mining process streams has proven very difficult to achieve by modem spectroscopic analytical techniques. Largely because no other technique has proven suitable, the basic fire assay process has become the accepted international standard for these metals. Fire assay, however, suffers a number of disadvan­tages in the modem, competitive, high technology, and increas­ingly environmentally aware world. It is a labour intensive technique that is difficult to automate, and requires high levels of skill to ensure accuracy and consistency of results. Potentially hazardous chemical reagents are employed, of which, lead, in particular, can be a serious source of contamination to both personnel and the environment if not effectively controlled. Other dangerous elements, such as mercury and arsenic, liberated in high energy furnace operations, are further sources of possible health and pollution hazards. n contrast, the energy dispersive K X-ray fluorescence (K­XRF) technique devised by K X Technology Ltd overcomes many of the technical constraints of conventional low energy X­ray analysis, and has the potential to revolutionise assay opera­tions in precious metal mining. The technology is simply automated, requires basic operator skills, uses no chemicals, consumes less than 20kW, and is capable of detecting gold and platinum to an accuracy of O .1 parts per million by mass. The new third generation design of AZTEC laboratory instrument, released in 1994, is the result of significant technical development. Capable of analysing over 1200 samples per day, and developed primarily for grade control sampling, its applica­tions have spread to gold ore accounting from on-line conveyor belt sampling; screening of exploration samples; measurement of gold in carbon granules for Carbon-in-Pulp process control; and for conducting rapid checks to support key managemen decisions. The economic, rapid, and non destructive analysis ofup to 80g of ore for large numbers of samples, reduces sampling and sub-sampling errors, and provides improved grade estimates for ore bodies. When interfaced to a LIMS, laboratory automation and cost-savings can be further enhanced. The AZTEC design is also being modified for the analysis of platinum. The GOLDSTREAM on-line analysis system is an important new application of K-XRF to the continuous monitoring of process streams in gold ( or platinum) plants and mills. Integrat­ing the technologies of K-XRF to measure total gold, and dissolved gold spectroscopy to measure gold in solution, the insoluble fraction of gold can be deduced, and the effectiveness of the extraction process determined. Slurries are sampled automatically from selected points of the plant and pumped to the system for analysis. The information produced forms the basis for plant control and optimisation.

Jan 1, 1995

By Y. K. Yen

The most serious problem for on-line coarse particle size measurement from a conveyor belt by image analysis is the overlap phenomenon that occurs between adjacent particles. A methodology is developed and described in this paper to estimate the sieve size distribution from the overlapped projected particle images as might be obtained from a conveyor belt. Two aspects of the overlap problem have been taken into consideration. First, several image processing algorithms were studied to find the most suitable technique to separate the projected overlapped particle images for narrow sized particles. These image segmentation algorithms include two-dimensional thresholding, edge detection and Watershed discrimination techniques. The other aspect of the overlap problem is related to the determination of the general kernel function for the partial particle images obtained from the projection of the overlapped particle bed. In this regard, a computer simulation technique was applied to mimic the overlapped particle bed for narrow sized particles, then the general kernel functions of the partial particle images were determined.

Jan 1, 1994

By M. J. McPherson, P. Mousset-Jones, G. Danko

Ventilation and refrigeration fortune climate modification contributes significantly to the operating costs of a deep hot mine. Mine climate simulation programs can he used to minimize the impact of these costs. There are several computer codes available to assist in this work. Whichever simulation program is used, it is the mine ventilation engineer who must supply the input data. This paper raises and answers the following question, namely, what accuracy is required of the basic input parameters, in order for a certain precision to he obtained in the predicted air temperatures? In the first part of the paper a new approach is described to estimate the dry and wet bulb temperature of the airflow, either in a dry or wet roadway. The calculation procedure allows an arbitrary temperature change with time, using Duhamel's superposition solution. Matrix-vector representation is applied to simplify the computational structure. In the second part of the paper the sensitivities of the dry and wet bulb air temperatures are analyzed, to the changes of the rock thernrophysical properties, the heat transfer coefficient, and the wetness factor.

Jan 1, 1987

By A. Cecala, J. Noll, J. Hummer

"NIOSH has observed that many control rooms and operator compartments in the US mining industry do not have filtration systems capable of maintaining low dust concentrations in these areas. In this study at a mineral processing plant, to reduce respirable dust concentrations in a control room which had no cleaning system for intake air, a filtration/pressurization system originally designed for enclosed cabs was modified and installed. Eighty-seven percent of submicron particles were reduced by the system at static conditions, meaning that greater than eighty-seven percent of respirable dust particles should be reduced. The particle size distribution for respirable dust particles are greater than for submicron particles, and filtration systems usually are more efficient in capturing the larger particles. A positive pressure near 0.02 inches of water gauge was produced which is an important component for an effective system and minimizes particles (e.g. dust) from entering into the room. The intake airflow was around 118 cfm, which is greater than the airflow suggested by ASHRAE for acceptable indoor air quality. INTRODUCTION Chronic overexposure to respirable silica dust (particle diameter < 10 microns) leads to a progressive lung disease known as silicosis. Workers who develop silicosis have an increased incidence of lung cancer and pulmonary disorders. In June 1997, the International Agency for Research on Cancer (1) found sufficient evidence to declare that inhaled crystalline silica in the form of quartz and cristobalite is carcinogenic. Mining is one of the leading industries for occupational exposure to silica dust (2-7). Control rooms located in dusty areas in some mines are of particular concern (8). Many mineral processing operations utilize operator’s compartments and/or control rooms to house workers who are performing particular job functions. Most industrial processing mills have rooms where a worker looks out over the facility and has direct control over the product flow throughout the entire building. In addition, primary crusher operators are often located in a compartment from which they are able to view the primary crushing function. Their job is to control when trucks dump into the primary jaw crusher and the rate of feed of the ore from the hopper into the crusher. Many of these control rooms and operator booths do not have filtration systems capable of cleaning air entering the control room or booth, which can result in elevated concentrations of dust in the room or booth. To reduce the dust concentrations in these rooms, it would make sense to clean the entering air with filtration/pressurization units similar to those proven to provide a clean environment in enclosed cabs."

Jan 1, 2016

By Daniel Lum

The limestone resources of Hawaii are derived chiefly from emerged fringing coral reef and coastal dune deposits of Pleistocene age. These deposits are most abundant on the island of Oahu and other older islands and least abundant on the island of Hawaii, the youngest. Their origin and depositional environment were influenced by glacio-eustatic rising and falling of sea levels during Pleistocene time. Dredged reef limestone deposits from two deep-water harbor projects have provided additional resources. Limestone uses include cement and lime manufacturing, concrete sand and aggregate, mad base material, beach sand replenishment, agricultural lime and golf course construction.

Jan 1, 1982