Search Documents

The Penetrating Cone Fracture (PCF) technology 1 is a new method of rock excavation developed by Sunburst Excavation, Inc. of Denver, Colorado. PCF is a rock excavation method which employs tensile breakage mechanisms under controlled conditions to enable the continuous excavation of rock?in underground and some surface applications. The technology has developed rapidly over the last two years to the point where it is now being prepared for commercial application in the mining and civil construction industries. The initial commercial application of PCF will be undertaken at the Perseverance Nickel Mine of Western Mining Corporation Limited in Western Australia beginning in May, 1994.

Jan 1, 1994

By T. A. Toney

With new lightweight designs, spirals have become standard equipment in coal preparation plants worldwide. To their credit, spirals typically show very low coal losses to the refuse stream under most operating conditions. However, spirals do tend to separate at cut points in excess of 1.80 S.G. Attempts to obtain lower cut points have typically resulted in coal losses to middlings. Middlings retreatment with secondary spirals is therefore becoming common place. Other forms of retreatment with water-only cyclones, hydrosizers, and recirculation have been attempted with some success. This paper reports on a novel (Patent Applied For) approach to retreating spiral middlings m a heavy-media-cyclone circuit.

Jan 1, 1998

By X. Cheng

The mechanism of cathodic decomposition of pyrrhotite was studied in deoxygenated solutions at natural, near neutral pH using potential and cyclic voltammetric measurements. Reaction products on pyrrhotite surfaces were examined by AES and XPS, and by analyzing the voltammograms for the electron balance of the reactions. Surface properties of the pyrrhotite/solution interface were characterized using ac impedance technique. The parameters of an equivalent circuit were determined by the nonlinear least squares fit (NLLSF) technique. The effect of cathodic polarization on floatability was investigated by micro-flotation tests. Possible implications to the flotation separation of chalcopyrite-pyrrhotite ores are discussed.

Jan 1, 1993

By J. W. Scott

The problems involved in installing, maintaining, and operating large vibrating screens have been summarized and discussed, based on a survey of current use of such screens in selected North American mineral processing applications. Practical, effective solutions for the more serious common problems are described, along with some recommendations on design practice for specifying, selecting, and installing large screens.

Jan 1, 1983

By B. V. Clingan

A practical application of recent design concepts makes it possible to design a column cell to fit a specific set of conditions. The design and operating parameters Of a column cell installation that replaced a conventional two stage copper flotation cleaning circuit at MAGMA COPPER COMPANY, SAN MANUEL, ARIZONA using these design concepts is described. A survey of other mineral processors using column cell technology was conducted. The results of this survey will also be discussed.

Jan 1, 1987

By John J. McCrone

In the Mining Industry, the means of handling and transferring lubricants has been given little attention over the years. An analysis of this process indicates that this neglect has often exacted a very high price. As the costs associated with labor, equipment utilization and waste disposal soar, the need for an efficient system takes on an increasing significance. Often the focus of bulk systems has been placed on the master container itself. Certainly, there is nothing new about a large lubricant container; they have been available over a period of years, known under a variety of names, "mini tank", "super drum", ?flo-bin" and "tote bin", to name but a few.

Jan 1, 1982

By A. B. Fly

This paper presents the equipment and techniques developed to mine subsurface mineral deposits through 16 inch bore holes entirely by hydraulic methods. Use of this equipment for excavating large cavities in oil and water well producing zones is discussed. Results of surface experiments using high pressure jet streams of water to determine the cutting rates of materials are outlined. Various basic shapes of subsurface excavations that can be mined with the equipment are illustrated and discussed. An example of the cost of mining by this method is presented. Problems encountered in the field operations led to the development of a new explosion type slurry pumping system and related slurry handling equipment.

Jan 1, 1969

By A. Ligorio Pires de Carvalho

The main potash deposit at Taquari-Vassouras is contained in cycle VII, and consists of several sylvinite bodies. Cycle VII belongs to a sequence of nine cycles defined by Szatmari (1974) in the Sergipe-Alagoas basin. The sylvinite layers are separated by halite beds. They are seated on or may be laterally in discordant contact with other lithologies such as the tachyhydrites at the base, and the limestone breccia at the top. The main structural features in the deposit include numerous synclines and anticlines, salt dissolution phenomena, and open fractures associated with the axes of the anticlines.

Jan 1, 1995

By N. G. W. Cook

The conventional cyclic system of deep-level mining by drilling and blasting gives rise to an inadequate degree of stope sorting when mining thin reefs. This results in poor utilization of the capital facilities of a mine in the form of shafts, haulages, airways and associated equipment. Continuous and controlled removal of the thin gold-bearing portion of the reefs would permit better stope sorting and hence greater utilization of capital facilities. Results of experiments to develop hard rock cutting machines for mining are reported and the benefits which could be derived from their use are discussed.

Jan 1, 1969

By S. Chander

The mechanism of oxidation of sulfur in pyrite is a function of the rate and driving force for oxidation. New evidence is presented in this article to show that at moderate potentials, a sulfur-rich hydrophobic layer is formed. Under ordinary conditions, the sulfur layer is covered with a layer of iron oxides, hydroxides, sulfate or oxy-sulfide ions. Under these conditions, pyrite is hydrophilic. In the presence of iron-chelating agents or iron sequestering ions, iron layer might not form. Under these conditions, sulfur-layer is exposed and pyritic might become hydrophobic. Stronger oxidizing conditions decompose the sulfur-layer, thereby making the surface hydrophilic.

Jan 1, 1992

By John C. Nixon

In 1959, The Australasian Institute of Mining and Metallurgy (Aus. I.M.M.) was asked by the Federal Government of Australia and the State Government of South Australia to join in the formation and management of a new contract research organization which was subsequently named The Australian Mineral Development Laboratories (Arndel) ? This body was formerly the Research and Development Branch of the South Australian Department of Mines which had been set up to develop the Radium Hill uranium deposit. It had then gone into contract R&D and the State felt that it would be more appropriate for the Branch to become a separate national organization. The Aus. I.M.M. decided that a professional institute could not participate directly in Arndel and, as there was no other suitable industry group to do so, it formed the. Australian Mineral Industries Research Association Limited (AMIRA). AMIRA held its first Annual General Meeting in September 1959 when the first Council was elected and the Memorandum and Articles of Association were adopted. The initial task of AMIRA was to raise guarantees of work or cash from its members to underwrite Arndel for the first five years of operation. The Federal and State Governments also provided guarantees and Arndel commenced operations in January 1960.

Jan 1, 1977

By Harold B. Goldman

On the basis of tonnage, the sand and gravel industry is the second largest nonfuel mineral industry in the United States. In 1990, the production of sand and gravel was 927 Mt valued at $3.4 billion. California, which leads the nation with more than 126 Mt, together with Texas, Washington, Michigan, and Ohio, account for 36% of the total production in the nation (Table 1). In commercial usage, sand applies to rock or mineral fragments ranging in size from particles retained on a No. 200 Sieve (0.074 mm openings) to those passing a No. 4 Sieve (4.76 mm openings). Gravel consists of rock or mineral fragments larger than 4.76 mm, ranging up to 88.9 mm maximum size. The construction industry consumes 97% of the sand and gravel produced; the remainder is sand used for specialized products such as glass (see chapter on Industrial Sand and Sandstone and Glass Raw Materials). Utilization The building industry uses sand and gravel chiefly as aggregate in portland cement concrete, mortar, and plaster; the paving industry uses sand and gravel in both asphaltic mixtures and portland cement concrete. Aggregate is commonly designated as the inert fragmental material that is bound into a conglomerate mass by a cementing material such as portland cement, asphalt, or gypsum plaster. Sand and gravel is also used as construction fill, road base and subbase, and decorative material. Portland Cement Concrete Aggregates: Portland cement concrete consists of sand and gravel surrounded and held together by hardened portland cement paste. Concrete mixes commonly contain 15 to 20% water, 7 to 14% cement, and66 to 78% aggregate. Sand and gravel used as concrete aggregate have to meet many requirements (Goldman and Reining, 1983). Premature deterioration of concrete has been traced in many instances to the use of unsuitable aggregates. Asphaltic Aggregate: Asphaltic mixtures used predominantly for paving consist of combinations of sand, gravel, and mineral filler (material finer than 0.076 mm), uniformly coated and mixed with asphalt produced in the refining of petroleum. Sand and gravel used as asphaltic aggregate must meet the same general physical requirements as materials used for portland cement aggregate. GEOLOGY General Requirements of Aggregates Construction aggregate has many requirements that are difficult to meet if only unprocessed material from natural deposits is used. Suitable material is composed of clean, uncoated, properly shaped particles that are sound and durable. Soundness and durability are terms used to denote the ability of aggregates to retain a uniform physical and chemical state over a long period of time so as not to disintegrate when exposed to weathering and other destructive processes. Individual particles must be tough and firm, possessing the strength to resist physical stresses and chemical and physical changes, that may cause swelling, cracking, softening, and leaching. The aggregate should not be contaminated by excessive clayey material, silt, mica, organic matter, chemical salts, and surface coatings. Physical Properties: The quality of aggregate depends upon its physical and chemical properties. These, in turn, may be inherent mineralogical and textural features of the rock or may be the effects of later changes such as tectonics, mechanical or chemical weathering, or incrustations. The physical properties most significant for concrete use are: 1) abundance and nature of fractures and pores, 2) particle shape and surface texture, and 3) volume changes which may occur because of freezing and thawing or wetting and drying. An aggregate is considered to be physically sound if it is adequately strong and capable of resisting the agencies of weathering without disruption or decomposition. Minerals or rock particles that are physically weak, extremely water absorptive, and easily cleavable are susceptible to breakdown. The use of such materials in concrete reduces strength or leads to early deterioration by promoting weak bond between cement and aggregate, or by inducing cracking, spalling, or popouts. Severely weathered, soft, micaceous, or porous materials may cause localized stresses to develop in concrete by swelling and shrinking during wetting and drying or freezing and thawing cycles. Physical Suitability of the Various Rock Types. Sedimentary rocks have a wide range in physical and chemical qualities. Sand- stones and limestones, if hard and dense, are ordinarily satisfactory, but many sandstones are friable and excessively porous and commonly are clay-bearing. Shales generally make poor aggregate material, being soft, weak, and absorptive. Most igneous rocks are satisfactory, being normally hard, tough, and dense. Tuffs and certain flow rocks may be extremely porous and have high water absorption and low strength. Metamorphic rocks differ in character. Most quartzites are massive, tough, and dense. Fine-grained marbles are usually durable, but coarse-grained marbles have low abrasion resistance. Gneisses are ordinarily very tough and durable. Some schists contain micaceous minerals that are undesirable because they are soft, laminated, and absorptive. Micaceous minerals are susceptible to splitting along cleavage planes and thereby impair particle strength and durability. Some schists and slates in particular are thinly laminated and tend to assume flat slabby shapes that lack strength-and do not pack well. Any or all of these rock types may be rendered undesirable because of harmful exterior coatings. Weathering processes, particularly the action of ground waters, deposit these coatings. The most common coatings are calcium carbonate, clay, silt, opal, chalcedony, iron oxide, manganese oxide, and gypsum. Particles with these coatings are undesirable as aggregates because the bond between particle and coating may be weak, and decreasing the strength of the aggregate-cement bond.

Jan 1, 1994

By Paul M. Godlewski, Roberto J. Guardia

Hundreds of highway and rail transportation tunnels in North America have been rehabilitated in the last two decades. Tunnel rehabilitation is usually dictated by an owner’s need to extend the working life of the structure, but typically has the added benefit of increasing capacity (greater speed or increased clearance) and enhancing safety. Not only has rehabilitation proven to be an economical alternative to new tunneling, but it can be safely accomplished by working during short work “windows” without taking the tunnel out of service. This paper presents methodology for planning and designing of tunnel rehabilitation projects, and case histories illustrate successful excavation and support technologies.

Jan 1, 2003

By P K. Kaiser, D A. Malovichko

Highly stressed excavations in hard brittle rock may fail by self-initiated, triggered or dynamically loaded strainbursts (Moss and Kaiser 2021). The low-frequency part of seismic radiation associated with strainbursts is described by a crush-type seismic source mechanism with a significant negative (implosive) isotropic component and a ‘pancake-shape’ CLVD deviatoric component. The seismic source is co-located with the excavation damage site. For such strainbursts, the ejection velocity is primarily related to the depth of strainbursting, the rock mass bulking characteristics, the duration of the bulking process, and the effectiveness of the support system. For dynamically loaded strainbursts, the displacement and energy demand may be augmented by the impact of the stress wave from a distant seismic event. This article describes the failure process and factors contributing to rock deformation and energy demands for support design. Case examples are used to demonstrate the dependence of rock displacements, rock ejection and energy demand on the factors described above. A seismic source model is proposed to assess the depth of strainbursting and the duration of the related bulking process by using seismic monitoring data. The implications for support design are briefly discussed.

Apr 26, 2022

By S. P. Singh

In order to understand the intricate nature of blast damage mechanism and to counter the associated problems, small scale blasting experiments were performed on hydrostone, concrete and granite. This was followed by a 2.4 m x 2.7 m (8'x 9') drifting operation in a quartzite quarry. Interior as well as exterior damage was assessed by different techniques. On the basis of the experimental results, the effect of explosive characteristics on the damage was examined.

Jan 1, 1992

By Fred T. Towne

Recent developments in fine grinding by the means of mechanical impaction are the result of continuing improvements in modern machine construction. This is especially true when related to the bearings and mechanically operated parts of impact mills. These improvements allow manufacturers to increase the speeds of the impacting members Most of the more common forms of size reductions, such as percussion, pressure, friction and sectioning, or cutting were at one time accomplished by human hands. These actions were transferred to machinery. Originally of limited application, their use widened as industrial materials and construction became more sophisticated.

Jan 1, 1965

By John Carson

Belt feeders are commonly used to meter the flow of bulk solids from bins and hoppers. If the interface between the hopper outlet and belt feeder is not designed correctly, flow from the bin may be severely compromised, resulting in problems of no-flow, segregation, flooding, etc. By knowing the flow characteristics of the bulk solid being handled and applying proven design techniques, such problems can be avoided. Relevant bulk solids flow characteristics are identified, along with measurement techniques. Design procedures for correcting problems with existing feeders as well as proper design of new feeders are presented, along with case histories of successful application of these procedures.

Jan 1, 2008

By Thornton L. Neathery

A small area in the Alabama Piedmont was studied to determine if metallic enrichment was associated with local magnetic anomalies. Cores from two holes in these magnetic anomalous areas have sulfide (pyrite, pyrrhotite, chalcopyrite) film on slicken-side and fracture surfaces. Two hundred and fifty soil samples were collected from the top of the "B" horizon on 1, 000 foot centers over the general trend of magnetic anomalies. Soil samples were leached with a 1:2. 7 mixture of HF and H2SO4 and the dilute filtrate analyzed for Cu, Pb, Zn, Ni, Co, Cr, Mo, and Cd, using atomic absorption methods. Concentration-value maps were prepared for each element. Small areas of anomalous concentrations were defined for Cu, Pb, Zn, Mo, and Ni. Some of these areas generally coincides with magnetic anomalies. Concentration values (ppm) range from: Cu 165.0 - 0. 5; Pb 265. 0 - 0.0; Zn 1386.0 - 43. 0; Ni 187.0 - 10.0; Co 207.0 - 6. 5; Cr 117.5 - 2.0; Mo 95.0 - 0.0; and Cd 32. 5 - 2.0. Studies of other magnetic anomalies appear warranted.

Jan 1, 1972

MULSIM/NL and La Model are displacement-discontinuity programs which have been used quite successfully in the past to provide detailed structural models of various single and multiple-seam mining situations. However, both of these programs required fairly complex details of the mine plan and topography to be manually input into the program, often taking several days of work. Recently, automatic mine and topographic grid generation capabilities have been added to the MULSIM/NL and La Model programs, reducing the input time requirements from days to hours. This paper discusses the algorithms used for the automatic grid generation and demonstrates the utility of the new capabilities with a case study.

Jan 1, 2003

The adsorption of gold onto activated carbon in iodide solutions has been studied. The adsorption rates were determined as a function of temperature, salt concentration and pH as well as activated carbon concentration. A kinetic model was also developed for the adsorption. The adsorption rate was believed to be controlled by a mixed mechanism of film diffusion and pore diffusion, but the film diffusion had a major contribution to the overall rate. Experimental findings were in good agreement with the model developed. The apparent activation energy was found to be 14.9 kJ/mol.

Jan 1, 1993