Search Documents

By W. W. Vaughn

In the technique described and evaluated, detection of mercury is based on the principle of atomic absorption. An analog signal, produced when mercury vapor absorbs ultraviolet light, is converted to digital form and calibrated to mercury concentration. Interferences are eliminated by selectively trapping the mercury on gold. The lower limit of sensitivity, using a 1-gram sample, is 5 parts per billion. A model of the instrument mounted in a station wagon has been tested successfully in the field.

Jan 1, 1964

By Duluth Engineers' Club, Engineers' Club of Northern Minnesota

"During the last ten years great strides have been made, on the Mesabi Range, in the practice of beneficiating low grade iron ore material. By .beneficiation is meant all methods of removing impurities, and raising the iron content to a point where it can be sold in open market, the principal impurities being silica and moisture. The • general processes to which low grade iron ores are amenable are as follows:1. Thermal(a) Drying ; removes hydroscopic or atmospheric moisture. .(b) Calcining; removes carbon dioxide from iron carbonate, molecular water from hydrated hematites, and atmospheric moisture.Roasting; removes sulphur, carbon dioxide, molecular water and atmospheric moisture.Agglomeration; primarily for the purpose of preparing finely divided material for blast furnace; briquetting and sintering.2. MechanicalScreen sizing; removes rock and sand.Classification; removes sand by means of currents of water of varying velocities.Log washing; removes fine sand.Jigging; removes larger particles of impurities than is possible by log washing. Certain types of jigs remove fine sand.Reciprocating tables; recover fine iron particles from sand discarded by above processes.Magnetic separation; applicable to the commercial separation of the magnetic oxide of iron from gangue material. From a scientific standpoint it is possible to separate certain hematites and limonites from their gangue:(g) Miscellaneous processes; comprise dry concentration, electro-static separation and other processes."

Jan 1, 1920

By John Duff Erickson

Determination of the final pit limits of an open pit copper mine is a problem that has far reaching effects on the life, profitability and operation of a mine. The solution to this problem requires that all of the significant variables affecting the final pit limits be considered together with corporate objectives as the guiding principle. This paper discusses the use of these variables and how they should be applied to plan the future of a mine. The objectives of a final pit plan; are determination of the extent and location of ore reserves, the allowable stripping to be accomplished to uncover the ore, the final pit surface intercept, final pit topography and the contained metal values in both ore and waste. The objectives of the plan must be consistent with corporate objectives as they pertain to profit, future investment in the mine, return on investment, alternative investments, conservation and perpetuation of the corporate entity. The subject will be treated in three parts: economic considerations, effect of leaching and pit design technique. At the outset, it is assumed; that the extent of and metal values in the mineralized area to be considered have been reasonably defined by development drilling and sampling.

Jan 1, 1968

By W. Nahas, T. C. Watson, A. R. Maycock

The development of roasting technology for the oxidation of sulfides in refractory gold ores is discussed. Case studies covering operations dating from the mid-1930's to the present day are used to illustrate this development. The roasting of ores and concentrates is reviewed and various gas cleaning flowsheets are discussed with particular reference to environmental requirements. A sequence chart is provided to show the development path of a potential roasting project.

Jan 1, 1990

By Sunil Jain, Jan M. Mutmansky

As coal mining evolves in this country, underground coal is being mined at greater depth and under more difficult conditions than in the past. At the same time, economic conditions make it necessary to mine more efficiently and economically. As a result, pressures on mining companies arise on two fronts and make the job of mining coal underground very difficult. Recent improvements that have been made in health, safety and productivity have come about primarily due to improvements in existing technology and better management of all the production resources. However, this trend can continue only so far and thus innovation will be needed to continue the improvement. This paper deals with a concept that, on the surface, appears to be more efficient in terms of the costs to provide ventilation. The resulting design is oriented toward increasing the ventilation efficiency through use of a unidirectional ventilation plan but it also promises to increase recovery and decrease the requirements for development entries. To analyze this ventilation concept, two mine layouts with a similar production schedule were planned in a hypothetical 1.83 m (6 ft) coal seam. The first alternative analyzed uses a traditional approach to ventilation with centrally located shafts and a bidirectional ventilation pattern. Using this system, it is necessary to use large-diameter shafts and a large number of main entries. Using the same assumptions on ventilation requirements, the second alternative utilizes unidirectional ventilation whenever possible, a smaller number of main entries and small-diameter blind-bored shafts in the bleeder areas. The comparative analysis is performed using PSU/TDMVS, a computer network analysis program that is capable of determining the ventilation power requirements at any time in the mine life and converting the costs to a present value. The economic analysis is then completed by including the shaft-sinking and entry-driving costs and the costs associated with the recovery of coal that are directly related to the change in the ventilation system. The results are summarized on a present-value basis.

Jan 1, 1987

By A. D. Shuloyakov, V. A. Zukerman, G. A. Finkelstein, V. I. Kurets

Possibilities of electric pulse disintegration are discussed with emphasis on high selectivity of the process as compared to mechanical comminution methods especially when applied to polymineral ores. Physical explanation of this phenomenon is suggested. The authors present results of some experimental tests illustrating regularity of this phenomenon irrespective of origin of ores or dissemination pattern of valuable minerals including both dissipated and accessory minerals. Some operating plants applying this principle are described the plants used either for mineral research purposes or for obtaining pure monomineral fractions or for treatment of gems to be faceted. Obstacles for implementation of this technology are mentioned.

Jan 1, 1995

By Peter M. Fozzard

A review is made of the actual costs of recent foreign mineral exploration programmes in third world countries. Target identification leading to the selection of areas, or macro-targets, must follow a well planned and defined series of steps. Suggestions are made with respect to this inter-active project development work. Potential revenues in the broad sense will always determine the overall economics of exploration but clear objective philosophy, good planning and adequate financing are essential for exploration success. Considerable opportunities exist for making important foreign mineral discoveries and broad selected suggestions are made for the identification of exploration areas in relation to high-grade and precious metal mineralization.

Jan 1, 1984

By Lawrence A. Roe

This paper describes research and development efforts leading to a wet process for the beneficiation of Western talc ores in which the values are primarily present as soft, platy talc mineral. The mineralogy of the ore, as it relates to the logic of utilizing an uncomplicated, attrition-scrubbing sedimentation process is described. Bench-scale laboratory testwork and a pilot-plant test program are described. The pilot-plant program included production of several tons of products. The thickened talc slurries were very difficult to dewater prior to the drying step. Dewatering difficulties were overcome by use of a high-speed centrifuge. The centrifuge cake was dried either by tray, flash or spray drying. The successful use of one high-grade talc product as titanium dioxide extender in paper is discussed. The talc product has extremely low abrasion values, an important characteristic for minerals used in paper manufacture. It is concluded that this wet process for soft talc ores is capable of producing high-purity talc products for paint, paper, cosmetics and other industrial uses re-quiring very pure soft talc.

Jan 1, 1972

By J. Mastoris

The determination of the surface area that may be impacted by underground mining is an important consideration in subsidence engineering. A number of parameters have been utilized to identify this influence area, most notably the angles of draw and break. This paper discusses the implications of selecting an appropriate "damage angle" for defining a potential damage area due to mining, within which surface structures may be impacted. Furthermore, the influence of both mining and geological factors (i.e., mining width, depth and overburden lithology) on this angle is examined using the Surface Deformation Prediction System (SDPS) software. Finally, recommendations are given for applying these concepts in subsidence control.

Jan 1, 1995

By H. Nakazawa

Galvanic contact, occurring between electricall y conducting minerals in flotation pulps, may affect the nature of mineral surfaces and influence their floatabilities. Rest potential and galvanic current measurements were made on an electrode combination of pyrite and pyrrhotite under nitrogen, air and oxygen aeration conditions, and the results were correlated with their oxygen-consuming characteristics and flotation behaviors. The galvanic contact improved the floatability of pyrrhotite, but adversely affected that of pyrite. Auger electron spectroscopy, x-ray photoelectron spectroscopy and scanning electron microscopy indicated that the formation of hydroxide or oxide and sulfate species of iron on pyrrhotite decreased whereas that on pyrite increased when these minerals were held in contact. An electrochemical mechanism was proposed for the observed behaviors.

Jan 1, 1985

By David R. Maneval

In 1956 the Legislature of the Commonwealth of Pennsylvania created a "Coal Research Board" in the Department of Mines and Mineral Industries. Over the years through amendments to the original legislation, the scope of authority for research has been expanded from the narrow area of improving and increasing the utilization of coal to covering all aspects of coal technology and any other area of interest which would be of value to the coal industry. In January of 1964, the Board commenced a vigorous program using appropriated funds and funds donated by the coal industry to finance a research program devoted to seeking solutions to the mine drainage problem. A review of published literature on the treatment of mine drainage indicated that much work done up to that point in time concerned only the mechanism of mine drainage formation and theoretical chemistry. Very few applied, developmental, or engineering studies had been devoted to finding practical solutions to the problem of polluted waters being discharged from active or abandoned mines. Projects were therefore undertaken on a wide variety of more utilitarian approaches. This paper will discuss briefly some of the pollution abatement approaches which have been funded by the Coal Research Board of this State, and will describe in some detail a multistage flash evaporator treatment plant now under construction.

Jan 1, 1970

By C. K. Jankousky

The midwestern area referred to is the Illinois basin. The coals presently worked are mainly the No. 5 and No. 6 coal seams which vary in thickness from five to eleven feet. Present average of the more important No. 6 id about nine feet. The coal can vary considerably in toughness within the same mine with some coal perhaps rashing very easily and other coal being extremely difficult to cut. Top is generally well laminated shales with some fortunate areas having limestone roof. There are local areas with troublesome top of poorly laminated shales, shale with slickensides and shale intermingled with small partings and traces of coal. The bottoms are generally one to three feet of clay which softens readily on exposure to moisture. The mines are dry although some water is released and collects from rapid penetration of the seam by continuous miners. However, there are locally wet areas. Most of this material refers to mines of the Freeman Coal Mining Corporation. The mining operations written about are underground mines in southern and central Illinois.

Jan 1, 1962

By Carlo Grandori

Early experiences The first double shield hard rock tunnel boring machine, manufactured in 1973, belonged to the generation of machines that were equipped with 12" dia. cutters. The experiences made with the 4.3 m diameter prototype ROBBINS mod 144-151 have been reported at the 1976 R.E.T.C. of Las Vegas (1): it might be worth recalling here that, with a specific cutter load not exceeding 10 to 12 metric ton and a 4.8 r.p.m. cutterhead speed, the average advance rate was of 350 meters per month of 21 working days with a peak production of 1,050 m of advance in 40 working days, in widely weathered and fractured granitic rocks of generally precarious stability, where a precast segmental lining was routinely installed as tunnel support. Over the 8.2 km of the Sila Tunnels, several badly crushed or sheared rock zones were bored through without major problems, even with water inflows of up to 30 1/sec. The same machine, with an improved design of the telescopic-and-floating shield area and equipped with flameproof drive motors, was taken to Colombia where, from September, 1979 to March, 1982 it drove 7.5 km of the Rio Negro-Chivor Tunnel in competent siliceous shales of up to 130 MPa at an average rate of 20 m/day.

Jan 1, 1987

By Richard Dunmore

Most coal seams in the United Kingdom contain firedamp, some of which is released into the ventilating airways as the strata around a working relax. The close sequence of seams in carboniferous strata is usually such that seams in adjacent roof and floor strata are also disturbed and potentially large quantities of firedamp can enter the workings from these sources. Since emission depends on the disturbance rate of the seams, higher coal production rates associated with increased mechanisation in the colliery accentuate the problem. Firedamp concentrations in UK underground workings are subject to statutory regulations1. To enable production to continue uninterrupted and in safety the problem is tackled by ventilation engineers by the provision of adequate ventilation in the airway and by the technique of firedamp drainage. In the UK the latter usually takes the form of cross-measure boreholes in roof strata, and increasingly also in floor strata, drilled from the gateroads, especially from return airways. In this way firedamp emitted from disturbed seams in adjacent strata can be extracted directly to the surface or to some safe position outbye, and the airways of the working district are not contaminated. Despite the use of firedamp drainage, considerable quantities of firedamp enter the ventilation air- stream and the concentration levels may be seen to be related to the coal production activites in the district. Figure 1 shows a typical recording of methane concentration obtained by a BM1 methanometer at a position outbye in a return gate where firedamp drainage was operating. The general rise in level throughout the working week may be seen, together with peaks occurring during production shifts and the gradual decay of emission over the weekend. In view of the fact that ventilation and firedamp drainage contribute a considerable proportion to the operating costs of the colliery, it is essential that the ventilation and firedamp drainage requirements be calculated as accurately as possible at the planning stage of the working. In the past the ventilation engineer has had to rely heavily on experience in neighbouring workings but with the development of mines in previously unworked areas there is clearly a need for a methodical approach to meet the requirements of planning. The work described in this paper represents such an approach and it is hoped that successful development and application of the method of prediction will lead to the widespread adoption of a routine procedure. The current development of a method of prediction of firedamp emission into longwall workings is based on the theoretical treatment of gas emission from coal seams proposed by Airey2 in 1971, which was based on his study of gas emission from broken coal 3 which was published in 1968. In common with other experimental methods of prediction, the method enables a calculation to be made of the total make of gas emitted from all sources of gas in the strata per tonne of mined coal.

Jan 1, 1980

By R. G. L. McCready, G. Dr. Heinrich, V. I. Lakshmanan

The objective of this study was to prove repeat loading capacities of physically stabilized fungal biomass from Penicillium sp. for the removal and recovery of uranium from mine water (Denison Mines). The testwork was carried out on a bench scale in small columns and proved that it is possible to stabilize the biomass in an inorganic compound. A lifetime of 10 loading-eluting cycles of the stabilizer biomass product was obtained by additional pretreatment. Sodium carbonate proved to be an effective elution medium. Loading and elution can be controlled by the pH values of the column. The effective loading capacity until the breakthrough point is approximately 70 % of the overall loading capacity. The loading capacities of the stabilizer biomass product are comparable to that of the original biomass. Uranium recoveries of 90 to 99 % were achieved during the loading and eluting under optimized conditions. Depending on the used biomass the described process might be applicable to remove uranium or other dissolved heavy or rare metals from effluents.

Jan 1, 1989

By Wayne R. Hopkins

Southern Arizona has one of the world's principal concentrations of copper ore bodies. Twenty miles south of Tucson, close to the Mexican border at Sahuarita in Pima County, is the Twin Buttes mine. In mid-1973, the Anaconda Company and American Metals Climax Incorporated (AMAX) established a 50-50 partnership to operate and expand the Twin Buttes property. Anamax Mining Company was established as the operating company for this joint venture. The production from the Twin Buttes mine is shared between the two partners who market independently. A major expansion of the Twin Buttes operation has included an accelerated stripping programrne for the pit, an expansion of the sulphide concentrator, the construction of an oxide leach plant and a 57 MW diesel generating power station. Part of this major expansion, the large tonnage oxide processing plant was brought on stream in 1975 and is now close to design capacity. The "mine to market gap" has been closed by producing high-purity copper cathodes at the mine site from oxide ore reserves. By using a hydrometallurgical process route, copper production is possible with negligible effects on the environment.

Jan 1, 1976

By Xinchun Li, Youdi Zhang

AI is one of the computing methods, artificial intelligence performs its calculation by simulating the intelligent behavior of human beings. It is regarded as one of the most important scientific achievements in the 20th century, A1 has been developed rapidly in recent years with the development of the computer technique .The application of AI in the mineral industry has also obtained rapid progress sine AI has been used in early 1980's, such as evaluation of resource, underground mining, surface mining and mine safety etc. It has played an important role for increasing mining efficiency, improving mining management and ensuring the safety of the miner. An integrated A1 system has been developed for coalmines environment management in this paper.

Jan 1, 2002

By Morgan M. Sears

The stability of gateroad pillars is crucial in deep-cover longwall mining, especially during transitions to wider panel layouts. This study evaluates the transition from a 700-foot to a 1,000-foot panel layout with an inter-panel barrier in a deep-cover longwall mine in Southwestern Virginia to identify a configuration that enhances stability and reduces operational risks. Using the LaModel program, three pillar configurations were simulated to assess their performance based on stress distributions and pillar safety factors. These included the previously used 4-Entry Yield-Abutment-Yield layout, the current 3-Entry Yield-Abutment layout with a 220-ft inter-panel barrier, and the proposed 3-Entry Yield-Yield layout with a 320-ft inter-panel barrier. The findings of this study suggest that the proposed 3-Entry Yield-Yield pillar layout is more effective in managing stresses in deep-cover mining environments. By optimizing pillar placement and improving load management, this layout could positively impact mineworker safety and health. The study underscores the importance of advanced simulation tools in developing innovative solutions to address the challenges of modern longwall mining operations.

Feb 1, 2025

By Robert J. Hite, James P. Searls, Sherilyn C. Williams-Stroud

Potash is a generic term that includes potassium chloride, potassium magnesium sulfate, potassium sulfate, potassium nitrate, and sodium-potassium nitrate mixtures. In the ceramics industry, potash is also used to refer to potassium oxide. Potash, primarily in the form of potassium carbonate, was the first industrial mineral produced in the United States, and the first US patent issued was for an apparatus and process developed in 1790 for its production (Paynter, 1990). Prior to the 1860s, potash was primarily sold as an impure form of potassium carbonate produced by burning hard- wood trees and leaching the potassium salts from the ashes. The major early uses of potash include soap and glass making, dyeing fabrics, baking, and saltpeter for gunpowder. In 1859, the development of a purification process to remove the sodium and magnesium chlorides was developed for the carnallite found at Stassfurt, Germany, and mined potash became available. With the appearance of mined potash and the earlier (1840) discovery in Germany by Justus von Liebig that potash was a nutrient for crops, potash started to be used for high valued crops such as cotton and vegetables. The German potash companies quickly developed a manufacturing process for producing potassium sulfate for tobacco fertilization. German potash supplied nearly all American needs until the embargo of the First World War when imports from Germany were interrupted (Bateman, 1918). With the discovery of potash deposits in New Mexico in 1931, the United States became self-sufficient in potash. In 1962, the United States began importing potash from Canada, and two years later domestic apparent consumption began to exceed domestic production. Along with nitrogen and phosphorus, potassium is one of the three essential plant nutrients, the "K" of NPK terminology. As a result, 95% of potash production is used as plant fertilizer. In all plants, inadequate potassium diminishes growth, causes increased disease, stalk and stem breakage, and susceptibility to other stress conditions. Plants take up large quantities of potassium from the soil, and potash fertilization replaces this loss so that each new crop can be grown with the same vigor and productivity as the previous year's crop. The potassium depletion of the soil from growing repeated cotton and tobacco crops is well known in the history of southern agriculture in America. George Washington was known to have studied alternative crops that could be grown on soil that had been depleted by repeated tobacco crops. Most of the remaining 5% of potash consumption is by the chemical industry, as potassium hydroxide to produce soaps and detergents, glass and ceramic products, dyes, explosives, alkaline batteries, and medicines. Potash as chemical is used in oil field drilling mud, the aluminum recycling industry, and the electroplating industry. Additional minor uses for potassium chloride include water softener regeneration, sidewalk deicing, and salt substitution for human consumption. Potash is used in the food industry as potassium phosphate, and in production of glass products as potassium carbonate or nitrate. GEOLOGY Potassium is the seventh most abundant element in the earth's crust and the sixth most abundant element in seawater. It is found in silicate minerals of igneous, metamorphic, and sedimentary rocks and is also a major constituent of many surface and subsurface brines. The majority of world potash resources are found in subsurface bedded salt deposits which yield high grade, large tonnage ore bodies and are amenable to low cost mining and beneficiation. Because of the relatively high solubility of potassium minerals, potash from salt deposits is ideal for use as fertilizers. Some potash production is from evaporation of naturally occurring brines, but the vast majority of current domestic and international production is from bedded salt deposits. Sylvite, carnallite, kainite, and langbeinite are some of the more important potassium minerals (Table 1). Sylvinite, a mixture of KC1 and NaCl is the highest grade potash ore. Carnallite can be considered a potash ore when removal of magnesium chloride is included in the beneficiation, but it can also be considered a contaminant when mining for sylvite. Potassium sulfate and potassium nitrate are typically manufactured products. Potassium sulfate is produced from mined minerals through conversion processes in Italy, Germany, and Carlsbad, NM, and from brines in southern California and at the Great Salt Lake in Utah. Natural deposits of potassium nitrate occur only in small amounts in Chile. The majority of potash-bearing bedded salt deposits are believed to have originated from the evaporation of seawater or mixtures of seawater and other brines in restricted marine basins (Schmalz, 1969). The reflux depositional model for evaporite deposition was first described in the literature in 1888 by Ochsenius. A shallow bar, or sill, across the mouth of a basin lets in a restricted flow of seawater which evaporates into a salt-precipitating brine (Fig. 1). The density of the brine at the distal end increases with increased salinity, sinks to the bottom, and sets up a reflux current of higher density brine back toward the ocean. The sill, which restricts the inflow of seawater, allows inhibited flow of evaporation-concentrated brines back to the ocean. The least soluble salts are precipitated nearer the sill, and the most soluble components come out of solution in the deeper parts of the basin. The result is a lateral facies change in a tabular-shaped deposit that is due to the salinity gradients in the brine (Fig. 2A). The asymmetrical facies distribution of the Paradox Formation (Middle Pennsylvanian) Utah (Hite, 1970), the Prairie Formation (Middle Devonian) in Saskatchewan (Holter, 1972), and the Salado Formation (Upper Permian) in New Mexico (Lowenstein, 1988), might prompt explanation by such a model. Other deposits, such as the Salina Formation (Upper Silurian) in Michigan (Matthews and Egleson, 1974), show a facies distribution that could be described as a bull's eye pattern. Although some small subbasins of high grade sylvite are found near the margins, the potash is generally located in a central part of the basin surrounded by successively less soluble facies (Fig. 2B). The sparse

Jan 1, 1994

By Carson Sharp Beltch

The determination of aqueous cyanide is accomplished by either detection in the sample as collected or by removal of the cyanide of the collected sample, followed by detection. The direct determination of the cyanide content of a solution can only be used in the simplest of systems, since many interferences can result in errors. Thus the most widely used method for total cyanide determination involve the reflux distillation of the sample using heat, acid and vacuum or air flow. The basic theory underlying this analytical approach is that by reducing the pH, the quality of molecular hydrogen cyanide will be in- creased and can be removed from the solution by elevating the temperature. The hydrogen cyanide is then collected in a caustic solution and analyzed. The general approach of removing the cyanide from the sample by distillation represented a major advance in this area of analytical chemistry. It enabled the determination of cyanide in many additional types of samples. When it became apparent that the tightly bonded cyanide complexes were not being detected by this approach, many methods fox complex ion destruction were proposed. These methods usually involved low pH adjustment with oxidizing mineral acids, coupled with the catalytic decomposition of the tightly hound complexes. All off the complexes except the strongest could he broken by these methods. The catalytic reflux distillation step has been found to have some negative aspects, since many materials that can be distilled with hydrogen cyanide will interfere with the color development step and result in a false positive reading.

Jan 1, 1981