Search Documents

By C. E. Capes

INTRODUCTION In the coal industry, ever greater amounts of fine coal must be processed due to the need to crush to finer sizes for impurity liberation in low cost physical cleaning processes. Fine coal processing is a major problem for the industry, both through the cost of disposal of reject fines and through the mining cost of lost coal values. Of the available disposal methods, impoundment has always been the most popular. In many cases, when the coal fines were of sufficient quality, froth flotation and expensive filtration methods were used to recover the coal in these waste streams. The coal fines are not always of a marketable quality, however, and flotation, due to poor yields and difficult dewatering, has always been an expensive and not necessarily profitable process. The oil agglomeration method is increasingly important as a technology for the treatment of fine coal-in-water suspensions. These fines can be preferentially wetted and agglomerated by many different oils mixed with the suspensions. Ash-forming impurities remain in suspension and are rejected when the agglomerates are recovered, for example, by screening. Agglomeration-based methods provide perhaps the only practical means for upgrading extremely fine coal to useful products on a large scale. As with froth flotation, oil agglomeration relies on differences in the surface properties of coal and impurities to effect separation. Whereas flotation be- comes less effective with particles finer than 200 mesh (0.075 mm) or coarser than 50 mesh (0.3 mm), there appears to be no lower limit on particle size for oil agglomeration while particles % in. (3.175 mm) diameter or larger can also be treated, if desirable. In addition to this ability to clean a broader size range of coal particles, oil agglomeration can produce a dense, coarse granular product of acceptable strength and low water content without the need for vacuum or thermal drying. The preferential wetting of solid surfaces by immiscible liquids has been utilized, if not fully understood, for a long time. Indeed Gaudin,229 in tracing the ancestry of froth flotation, refers to a 15th century oil-pulp kneading procedure in which water-wetted particles were freed under water from an oiled mass. An understanding of the physical chemistry involved in such

Jan 1, 1991

By R. Schuerch, G. Anagnostou, R. Poggiati

"The paper presents dimensionless design diagrams for estimating the stand-up time of a tunnel face in saturated ground of medium-low permeability. The diagrams cover a wide range of ground parameters and apply to shallow tunnels (overburden less than two diameters). As the time-dependency of the face stability in water-bearing ground is associated with the consolidation process in the soil ahead of the tunnel face, the stand-up time is determined by means of hydraulic-mechanical coupled spatial stress analyses. The results presented are important for tunnel engineering practice, e.g. when estimating the feasibility of atmospheric interventions in the working chamber of a closed shield. INTRODUCTION The response of water-bearing medium-low permeability ground to tunnel excavation is time dependent. The time-dependency is due to a transient seepage flow process that is triggered by the excavation and develops slowly over the course of time. Experience shows that the short-term behavior the ground is more favorable than the long-term one: the deformations increase with time; the tunnel face may be stable initially and fail only after some time. The time over which the tunnel face remains stable is called the stand-up time. This paper investigates the time dependency of the tunnel face stability assuming that all time effects are due to consolidation rather than creep. This assumption is reasonable for shallow tunnels crossing water-bearing soils. In the problem under analysis, the unsupported tunnel face remains stable under the undrained conditions prevailing after excavation, but collapses before reaching the drained conditions prevailing at a steady state. The assessment of the stand-up time is important from an economical point of view for both mechanized and conventional tunneling through weak water-bearing ground, as a long stand-up time removes the need for face support or ground improvement works during standstills, thus saving time and money, while short stand-up times require hyperbaric interventions or the implementation of costly and time-consuming auxiliary measures."

Jan 1, 2016

By Michael Bayerl

The HILTI OneStep rockbolt was implemented for roadway development in German deep coal mines in 2004. The development by HILTI Company is based on a technical joint venture with RAG Deutsche Steinkohle AG. The technical development of a One-Step bolting system was required for weak strata conditions at the roadway development face. Standard resin bolting has reached the limit of performance when boreholes are squeezed and cannot be filled with capsules. In some cases the heading face is brittle and requires additional support for installation of the bolts and a person working immediately next to the borehole. The Hilti One-Step system allows automated and safe processing at the heading front and provides the key technique to avoid these problems.

Jan 1, 2009

By William C. Ellis

Underground water is part of a continuing hydrologic cycle, which involves all elements of water occurrence. All groundwater of economic importance is in process of movement through a porous rock stratum from a place of intake or recharge to a place of disposal. Groundwater moves and is contained in fractures in the rock and/or in intergranular spaces of porous formations. Where there have been no water developments by man, groundwater is in a state of approximate equilibrium and the forces of replenishment and discharge are in balance. Thus, groundwater, unlike other mineral resources, is constantly being replenished in most areas at a rate which is measurable and which is important in the planning of its utilization. As illustrated by Figure 1, replenishment of groundwater supplies results from the direct penetration of rainfall through the soil to the water table, by seepage from surface streams or ponds, and/or by subsurface movement from an adjacent groundwater body. Under natural discharge conditions, water is commonly consumed by transpiration of trees and other types of vegetation, by flows from springs, by evaporation from shallow depths below the surface, and seepage into streams that traverse the area.

Jan 1, 1964

By Bruce M. Davis

The variogram is the function used to express the intercorrelation of a regionalized variable. It is used to quantify, for example, the natural variability of mineralization and in that sense may be thought of a average disimilarity between metal quantity at two points inside a deposit.2 As David2 explains, appropriate mathematical functions of distance and direction are used to characterize variograms, a process that he says is analogous to selecting a normal or lognormal model for an observed distribution. Methods for choosing a model for the underlying variogram of a random function based on the sample data appear in the literature.3,8 A crossvalidation procedure is available to check the validity of the model.3 However, statistical validation of the choice of the model through the mechanism of hypothesis testing is not presently available. In the section to follow, notation and background material is presented upon which a large sample test procedure will be constructed. The stationarity assumptions presented refer to covariance stationarity. A test procedure is then proposed, and an example is given for the case of the one dimensional random process.

Jan 1, 1979

By Thomas W. Camm

A WINDOWS-based object-oriented expert system for prefeasibility evaluation of hard rock mines is being developed at the Western Field Operations Center (WFOC) of the Bureau of Mines. Designed for use with the Bureau's Cost Estimating System (CES), this expert system assists an evaluator in choosing an underground mining method, and the related design parameters. The system provides the engineering and design guidelines necessary for an evaluator to perform a prefeasibility type cost estimate.

Jan 1, 1992

By Prasad Kummarapurugu, Maija Teijonsalo, Sirkka-Liisa Jamsa-Jounela

There has been a significant progress in the use of mathematical modeling and simulation in the minerals industry in the last decade. Process models have moved from academic world to important industrial tools. This paper reviews the status of mineral processing simulators and recent progress in simulator development and applications is discussed. The simulation for process design and optimisation is now an established technique, as evidenced by its increasing use of practising engineers through commercially available simulator software. The paper presents a systematic approach to the process study procedure for the control system development, clarified by practical case examples calculated by SimCon - a novel steady-state simulator for mineral processes. Examples of the application of SimCon in drawing flowsheets, calculating mass balances and making simulations for grinding and flotation processes are presented. At the end of the paper, the state-of-the-art and the future of computer-aided pro- cess study at mineral processing plants is discussed. Keywords: Simulators, modelling, object oriented programming, computer aided control system design

Jan 1, 1996

By Philip Lindstrom

Retreat mining, using yielding steel friction props, over a seven-year period has been successful at a uranium mine operated by Hecla Mining Company in southeast Utah. The support system allow good roof control, maximum profit, complete extraction, and good ventilation. Unusual subsidence observations were made in that some of the surface was raised rather than lowered, Longwall mining, commonly practiced in European coal mines, has a potential of broader application because of mechanization possibilities and better roof control and ventilation at greater depths.

Jan 1, 1964

By L. M. Turner

Perlite is a unique mineral that upon heating expands to about twenty times its original volume. Mining is by open pit method. The processing cycle involves crushing, screening and sizing the ore. An on-site quality control facility at the Manville Products No Agua mine exerts a high degree of control over every phase of the operation from blasting to finished product.

Jan 1, 1985

By R. S. Austin

One third of the world's and most US kaolin is produced from Late Cretaceous and Early Tertiary sedimentary strata in Georgia and South Carolina. The kaolin is part of a belt extending to Arkansas of aluminous lateritic deposits, including bauxite. Original sediments were profoundly altered by chemical weathering during Early Tertiary time. Mining exploits those uncommon deposits where extreme leaching and chemical recombination have produced a clay of nearly pure mineral kaolinite. . Its whiteness, brightness, fine particle size, platelet shape, surface chemistry, and chemical composition make kaolin an important pigment, filler, extender and chemical compound in the paper, paint, plastics, ceramics and catalyst industries.

Jan 1, 1998

An appropriate scale-up methodology is very useful for ball mill design and optimization of the grinding circuit. To date, the scale-up is based on the selection and breakage function method using lab mill data. However, a major drawback of that approach is that the charge motion in a lab mill is vastly different from that in a large industrial mill. Therefore, in the methodology proposed here, first the energy of individual collision in the mill is computed employing the discrete element method (DEM). Then the breakage of particles as a function of collision energy is studied in a separate experiment. Together, this information constitutes what is known as collision energy based population balance method. The appropriateness of this method is shown for 38-cm ball mill.

Jan 1, 1998

By D. Gove

All mining operations using trucks have a common need to properly match the number and size of hauling units (trucks. wagons. scrapers. etc.) to a loading unit (wheel loader. hydraulic shovel/excavator, cable shovel. push tractor. etc.) to provide the best possible fleet match. Optimizing fleet match minimizes the cost per unit of material moved by that fleet. As haul conditions change (haul length. grade. or rolling resistance), there may be need to adjust the number of trucks to maintain the optimum fleet match. Fleet Production and Cost is a tool which, among other things, can be used to optimize the truck-loader match.

Jan 1, 1994

By L. M. Petrie, D. C. Marozas, S. E. Paulson

The US Bureau of Mines (Bureau) is conducting research to evaluate the potential for developing an in situ leach mining process that will selectively extract manganese from oxide ores, leaving gangue relatively undisturbed. To accomplish this, a geochemical approach based on deposit-specific information, such as mineralogy and geology, is used to constrain the operating parameters of the system. Among the studies being conducted are: • leaching experiments to define reaction mechanisms and kinetics, • detailed petrologic characterization at the microscopic scale to assess manganese distribution and leaching efficiencies, • deposit characterization and evaluation, and • development of potential manganese recovery schemes. Data from these studies are being used to develop engineering design information for an in situ mining process. Specific details of the Bureau's research project are discussed, including results obtained to date.

Jan 1, 1993

By Z. T. Bieniawski, D. A. Newman

The Geomechanics Classijication (RMR System) (Bieniawski, 1979) was modified for entry and roof support design in underground coal mines. Adjustment multipliers were introduced to incorporate the influence of high horizontal stresses and the roof support reinforcement into the existing classification system. Sixty- two case histories of standing and fallen mine roof were collected from two mines in the northern Appalachian coalfield. Twenty-seven engineering and geologic parameters were recorded for each case. A partial correlation analysis was carried out on the cases to establish which parameters have a significant im- pact on the stand-up time of supported coal mine roof. Survival analysis, a statistical technique used in medical research to assess the effect of a drug or treatment on a patient's life expectancy, was conducted together with stepwise multiple regression to derive values for the adjustment multipliers. A practical example is included to illustrate the application of the modified Geomechanics Classification to underground coal mine design.

Jan 1, 1987

By S. Constantinescu

The alloys mainly used for short (or segmented) chip material cutting (cast iron, porcelain, etc) are alloys of the WC-Co type; in some cases with small additions of other carbons. The same alloys but of different granulometric classes are also used for pieces exposed to wear (wire drawing, moulds) The higher performance of the WC-Co alloys in chip machining applications is accounted for by their very good heat conductivity, which is 2-3 times higher than that of fast steels. The hard-alloys producers can resort to a wide range of possibilities to achieve variation of properties of a WC-Co composition and thus they can adapt their products to the particular type of tools they may choose to manufacture. The present metallography technique allows for a correct identification and evaluation of hard sintered carbons structures. The metallography approach is an indispensable method of investigation and control in the industry.

Jan 1, 2008

By Ronald P. Wright

ARAMIDS UNDERGROUND COAL MINING

Jan 1, 1993

By D. Leppert

Large deposits of natural zeolites may provide cost-effective alternatives for treatment of soil and water contaminated ) with heavy metals and radionuclides. Research on the Bikini atoll demonstrated that addition of clinoptilolite to the soil significantly reduces cesium uptake by plants. Re- search on the potential use of zeolites in soils at Bunker Hill, ID indicated only minor benefits at very high contamination levels vs. US Bureau of Mines (USBM) work on the use of zeolites for treatment of mine waste waters emphasized problems with natural waters that previous studies have not addressed. High levels of competing calcium in natural waters significantly decrease the effectiveness of zeolites for heavy metal sorption and may limit the usefulness in these applications.

Jan 1, 1991

By I. Ehie, Y. P. Chugh

Physical mine modeling and computer simulation techniques were used to conduct technical feasibility and economic analyses of selected pit configurations for surface mining a single coal seam dipping at about 15% to a maximum depth of 46 m (150 ft). Pit orientations along the true dip (dipline), along the strike (strikeline), and along an apparent dip were studied. Physical models of each pit configuration were prepared first to delineate potential operational problem areas and also to furnish data for the computer simulation models. A dragline microsimulation, a shovel/truck simulation, and a surface mine cost analysis models were used to conduct the study. Sensitivity analyses were conducted on variables such as the pit width, block length, and seam pitch. The productivity (m3/h) of the mining equipment (dragline or stripping shovel) under each set of conditions was used to optimize the pit configuration. Both block length and panel width were found to significantly affect the dragline productivity. Larger size trucks were preferable to smaller size trucks in the pit con¬figuration along an apparent dip. The cost analysis results showed that the pit configuration along the seam dip was more economical than the pit along the strike or along an apparent dip for the mining condition studied.

Jan 1, 1987

By Jiqing Zhang, Jon C. Yingling, Andrzej M. Wala, Richard Ray

The purpose of this paper is to present how Computational Fluid Dynamics (CFD) simulations can be used to study the flow across the main airways of a mine ventilation system. in particular, the flow through the transition zone between the upcast shaft and main fan ductwork was investigated. These studies consider potential design modifications of this transition zone to reduce the energy cost. Although CFD has many advantages, it does not completely eliminate the need for experiments, which are still needed to validate numerical solutions. For this reason, data collected during actual mine tests and CFD simulations are compared in this pa- per. This comparison allows a better understanding of the flow phenomena. Moreover, once the numerical solutions have been validated, CFD can be used with better confidence to predict the effect of changes in ductwork configurations on energy losses. CFD reduces the number and cost of tedious experiments, while enabling a broader scope of design comparisons.

Jan 1, 1997

By Michael J. Shulman

Outcrops of the Nubian Sandstone Series cover approximately 180,000 km2 in southern Egypt. Within the series, oolitic iron ore beds occur. The only comprehensive information available on stratigraphy of the iron beds is for the area east of Aswan, otherwise information is exiguous, sparse or unreliable. Based on this low level of information, the iron potential of the Nubian Sandstone Series was assessed and an exploration strategy formulated specifically tailored to the assessment. The area covered by the Nubian was divided into five regions, each comprised of 100 cells. A spatial distribution, i.e. negative binomial, was assumed adequate to describe the number of targets per cell and was indirectly calculated using a compound poisson distribution. Estimate of the only unknown parameter - the average number of targets per cell - implicitly/explicitly incorporated available geologic and economic information into the assessment. A probability distribution for the number of targets per region was then derived from the cell probability distribution. An allocation model based on the regional probability distribution assessment as well as on an estimate of the exploration effectiveness and on the exploration budget determines the optimal time to be spent in each region.

Jan 1, 1986