Search Documents

By Fred N. Kissell

INTRODUCTION During the last few years, several new ventilation developments have attracted the interest of mining engi¬neers. Some of these developments are applicable pri¬marily to hard-rock mining, while others are more applicable to coal mining. STOPPINGS Parachute Stopping The parachute stopping is a new type of quick-erect stopping that is intended for temporary use in hard-rock mines (Kissell, Thimons, and Vinson, 1975). As shown in Fig. 1, the stopping is shaped very much like an ordinary parachute, with a canopy of impermeable fabric that is sewn to regularly spaced straps running to a common point. To erect the stopping, the straps are attached to a fixed anchor point such as a roof bolt, and the edge of the canopy is lifted into the moving air¬stream. The airstream pops the parachute canopy into place, and the differential air pressure across the stop¬ping holds it in place, forcing the fabric against the walls, roof, and floor of the mine opening. The principal advantage of the parachute stopping is that it requires only a few minutes to install, making it a great time-saver for emergency use or for day-to¬day changes in ventilation during the production cycle. However, the parachute stopping does require some minimum air velocity to lift it and some minimum differential pressure to hold it in place. For a fabric weighing 0.27 kg/ m2 (8.0 oz per sq yd), the minimum air velocity is about 0.5 m/s (100 fpm), and the mini¬mum differential pressure is about 0.05 kPa [0.2 in. water gage (WG) ]. There is always some air leakage around the stop¬ping, mainly depending upon the extent to which pipes or other obstructions encumber the airway and prevent good sealing. Leakage of a few cubic meters per second (a few thousand cubic feet per minute) can be expected, unless foam is used to improve the seal at the edges of the canopy. Quick-Fix Blowout Stopping The quick-fix blowout stopping is a variation of the parachute stopping (Thimons and Kissell, 1976), and it is used in the proximity of blasting operations. This type of stopping is designed to be blown out easily by the blast forces, and it may be reinstalled quickly and easily. The long high-strength straps of the parachute stopping are replaced by groups of short straps that tear easily. These straps are attached at six equally spaced locations around the perimeter of the canopy. To erect the stopping, one strap of each of the six groups is fastened to the mine wall, roof, and floor by using spads, by setting pins with a powder-actuated gun, or by tying the straps to some firm anchor point. Once the straps have been attached, the differential air pressure across the stopping, which must be at least 0.025 kPa (0.1 in. WG), forces the stopping perimeter against the mine walls, thus creating the air seal. It is the self-sealing feature of this stopping that makes it a significant time-saver. Only a few attachment points are needed; in many cases, four attachment points are sufficient, since the stopping naturally tends to form a seal with the airway surfaces. When nearby produc¬tion blasting exerts excessive forces on the stopping, one or more of the straps tears away from its attachment point, protecting the stronger canopy from damage. Damage-Resistant Brattice The damage-resistant brattice is a stopping that is designed for use in mines such as salt and limestone mines where the differential pressures are low and the roof is relatively flat. As shown in Fig. 2, the damage-resistant brattice consists of a series of brattice panels that are hung vertically and joined by Velcro® connections. When the brattice is subjected to strong blast forces, the Velcro® connection peels apart and allows the panels to open without incurring damage. The Velcro® connections can be resealed by hand within a matter of minutes. Such damage-resistant brattices have withstood the blast effects of 318 kg (700 lb) of ammonium nitrate-fuel oil (ANFO) explosive detonated as close as 91 m (300 ft) from the brattice. Ordinary brattice cloth is used for the panels, with a 51-mm (2-in.) wide strip of Velcro® hooks sewn along one edge of the length, and a 51-mm (2-in.) wide strip of Velcro® pile sewn along the other edge. Both the hooks and the pile are sewn onto the same side of the brattice cloth. The resulting Velcro® seal formed be¬tween adjacent panels is perpendicular to the brattice itself, and the leading edge of the seal can be directed either toward or away from the blast forces; the brattice works equally well in either case. To hang the brattice, panels of brattice cloth about 0.9 m (3 ft) longer than the height of the airway are cut from a 1.8-m (6-ft) wide roll. The additional 0.9 m (3 ft) of brattice cloth allows 0.3 m (1 ft) for attachment to the roof by means of a board, with 0.6 m (2 ft) for forming a good air seal at the floor. Each brattice panel is wrapped once or twice around a 51 X 102 mm (2 X 4 in.) or 25 X 76 mm (1 X 3 in.) mounting board that is 254 to 305 mm (10 to 12 in.) shorter than the width of the panel. For convenience in

Jan 1, 1982

By A. D. Davis, G. A. Zabolotney

A ground-water flow model was developed to simulate the postmining recharge rate from precipitation at the Belle Ayr surface coal mine, which is located in the Powder River Basin near Gillette, WY Wyoming state regulations require that reclaimed lands should provide a rate of recharge that approximates the premining rate. Steady-state calibration and transient simulations showed that the postmining recharge rate through spoil is at least 50 mm (2 in.) per year, exceeding the original infiltration rate of 4 mm (0.16 in.) per year to shallow overburden aquifers. Major reasons for the increase include the flat topography of the reclaimed areas and the decreased spoil density. It is expected that the backfill will disaggregate and settle over time, eventually resulting in a nearly constant recharge rate that is less than 50 mm (2 in.) per year but still somewhat greater than the premining rate.

Jan 1, 1997

By Peter G. Chamberlain

Many mining engineers considering in-place leaching for the first time are uncertain as to how to evaluate ore bodies for potential leachability. Evidence presented in this report emphasizes the critical role of permeability in such evaluations. Whether an engineer is considering leaching "tight" formations typified by the porphyry copper deposits of the southwest or the permeable uraniferous sandstones of Texas and Wyoming, permeability measurements are the keystone of any testing program. Permeability tests range from cheap and easy to highly expensive and sophisticated operations. Constant head, variable head, and pumping tests all have application in evaluating ore bodies for in-place leaching. Costs of these tests will not unduly deflate the pocket- books of most mining companies. The basic procedures for selecting and running these field tests-including preparing suitable wells--are reviewed for the benefit of newcomers to in-place leaching.

Jan 1, 1979

By Harry Perry

A technology for producing liquid fuels from oil shale at prices competitive with crude oil prices is a necessary but not exclusive prerequisite for the development of a shale oil industry. Many other factors will affect the timing and the rate at which oil shale is commercially developed. Among the more important are: governmental policy concerning oil shale and oil resources (including the Outer Continental Shelf) that are under Federal control; oil import policy; Federal taxation of shale oil production including depletion allowances; regulatory practices; competition from other energy sources, both synthetic and natural; Federal treatment of factors affecting competing energy resources; and present legislation under which the public resources must be leased. Significant changes in any of the foregoing factors could have a controlling effect on the timing and rate of oil shale development. The effect of changes in each of these factors is evaluated.

Jan 1, 1969

By Esko O. Nermes

Outokumpu flash smelting of copper concentrates was introduced in 1949 and flash smelting of nickel concentrates in 1959, both at Harjavalta in southwest Finland. The first flash smelter outside Finland was started up in 1956 in Ashio, Japan. Between 1956 and the present about 25 flash smelters for copper, and nickel concentrates have been put into operation in different parts of the world. Outokumpu"s research organization has been highly involved in the development of flash smelting. For example, a direct blister flash smelting process was developed in 1975 and introduced in Glogów, Poland, in 1978, and another has been designed for Zaire. This straight metal process is based on low iron content of the concentrate, which reduces the amount of recycling slag copper. Additionally, the concentrates are rather low in impurities.

Jan 1, 1982

By M. E. Lewellyn

A lower moisture content for a clean coal product means increased Btu content, or increased yields at the same Btu content, and lower operating costs. The conventional surfactant-based dewatering aids effeciently lower the moisture content but often the presence of residual surfactant in the filtrate and recycle water causes problems downstream. ACCOAL-DRI 1000, a surfactant-based dewatering aid, was developed to solve this problem by minimizing the downstream effects while efficiently lowering the moisture content. The theory of the use of surfactants in filtration will be discussed as well as the development and field evaluation of this new product.

Jan 1, 1988

By T. H. Eyde

Natural Zeolites are a less expensive and in certain applications a superior alternative to organic ion exchange resins. Mining and metallurgical waste streams are difficult to treat because the effluents which contain potentially valuable heavy metals such as copper, lead, and silver are often highly acidic and contain significant quantities of suspended solids. Under rigorous operational conditions, certain natural zeolites can remove the metals, which if desired can be recovered by either elution or conventional smelting techniques. There are significant differences in cation exchange rate, selectivity and capacity as well as resistance to either high or low pH, blocking cations and tolerance to elevated or depressed temperature and pressure not only between different zeolite minerals but between the same mineral from different deposits. Applying natural zeolites to the treatment of mining and metallurgical waste streams depends on matching the specific zeolite to the effluent by characterization of the zeolite minerals.

Jan 1, 1994

By William Ives

My presentation is from the viewpoint of the industrial mineral geologist, which is a relatively rare breed. Very few geologists become involved with industrial minerals for two reasons, I think: (1) Much of the industry utilizing non-metallic minerals has developed without the use of geologists in the begin¬ning and many of the management people, who generally derive from the processing plant supervision, tend to take raw materials for granted; and (2) non-metallic minerals are a very insignificant part of the curriculum of virtually all colleges granting a geology degree. One learns about the geology of industrial minerals by working with it. This "on-the-job-training" is probably best because it brings the geologist into close quarters with the production people and the production process. And the industrial minerals field has a distinctiveness when compared with the petroleum or metal mining field in that each deposit can yield a material differing in some aspect from that in any other or within the same deposit. The petroleum from a well in a given field will be similar to that from any other well, but a limestone on one side of a hill can differ signifi¬cantly in elemental composition, calcinability, soundness, specific gravity, or some other factor from the same ledge on the other side of the hill. This characteristic of almost certain variability creates problems sooner or later and provides for much of the employment of industrial mineral geologists. My job seen from the viewpoint of management is "Find us some rock we can extract and process at a profit." The industrial non-metallic geologist has much the same problems and approach as a detective. I do not mean the TV variety with the big mouths and the unfailing knack of spotting the wanted criminal immediately in a city of ten million people. Any real detective will tell you it takes leg-work, knowhow, and persistence to make a case. The same is true for the geologist who finds rock which can be quarried at a profit. I am responsible for finding raw materials for a company which manufactures portland cement and

Jan 1, 1977

By William C. Baldwin

Unitization and containerization continue to grow with great rapidity throughout the world today. Every industrial nation outside of the Iron Curtain is devoting more and more time toward research of these developing sciences. Unitization and containerization are proving to be the solution to many of modern industry's most pressing handling and shipping problems. Manufacturers make large savings, carriers receive many benefits, and customers take an increasing interest in demanding that their shipments either be unitized or containerized. Unit-loads consist of items, packages or bulk materials pre-assembled into a convenient mass for handling by mechanized equipment and to fit the internal dimensions of carriers. It has been found that unitized handling and shipping offers cost savings too great to be ignored by anyone interested in the distribution of goods. At present, the benefits from unitized shipping and handling are being enjoyed only to a small extent due to the failure of many persons concerned with handling practices in recognizing only some of the advantages of unitization. Before the full benefits of unitized handling and shipping can be realized, some major changes in packaging and distribution practices will be necessary on the part of industry. Numerous investigations in the last two years show conclusively that there are more advantages and more inherent savings for shipping goods on pallets in unit loads than by any other method. There is no question that unit-load handling can offer significant advantages to the user over piece-by-piece package handling. Reduction in handling costs is the primary objective of such activities, but it is by far not the sole objective. Some of the other benefits that can be realized are:

Jan 1, 1973

By Connor Meinke, Shaihroz Khan, Kevin Erwin, Rajiv Chandramohan, Muhammad Usman Siddiqui

A geometallurgy study aims to link metallurgy and geology to reduce technical risk and enhance the economic performance of a mineral-processing plant. It does so by accounting for variability in a deposit to develop cash-flow models with variable throughput rates. High-quality sample selection for metallurgical test work that is representative of the deposit is an essential component of a geometallurgy study, but the large multidimensional data set makes sample selection a daunting task, as classifying the data set while respecting its heterogeneity is difficult. This paper presents a streamlined approach for sample selection, using statistical analysis techniques in Python. It cuts down time to select samples from around 1,200 s per drillhole to about 60 s for data classification and from 12 h to 8 h for handpicking samples from the classified data set, translating to cost savings. The cumulative sum method and k-means clustering method are used in the methodology to elegantly classify the data and select representative samples. The effectiveness of the methodology is demonstrated by presenting data from a prefeasibility study of a copper-iron mine in which 40 samples were selected for flotation test work.

Dec 1, 2024

By CAIJUN CHEN, MING ZHANG, ZHENWEI WU, FENG ZHOU, BOQUAN LI, XILIANG ZHANG, ZHOU PU

Traveling grate is a widely used process for iron ore pellet production; however, the thermal state of pellets in drying section is still unclear. In this study, the temperature distribution of drying section was investigated using computational fluid dynamics (CFD). Based on the calculated results of airflow velocity, space temperature distribution, and the temperature change of pellets, it concluded that there is a coupling effect in drying section in traveling grate. The gas with higher temperature in DDD transfers heat to UDD through the gap of the insulation board, and the temperature gradient of the pellet bed changed before reaching the insulation board. The characteristics of pellet bed expected to appear in DDD was displayed in UDD in advance. Moreover, a contrast experiment was conducted to verify the model.

Feb 1, 2021

By J. Groff

The Getchell and Twin Creeks mines are located along a north-northeast trending structural zone in Humboldt county, Nevada approximately 40 miles northeast of the town of Winnemucca. Gold mineralization at the Getchell mine is represented principally by sulfide-rich ores, which contain significant amounts of realgar and\ orpiment, with the gold being recovered through processes which involve pressure oxidation. In contrast, oxide ores are currently being mined and processed at the Twin Creeks mine although large reserves of sulfide ores, some of which contain orpiment-realgar-stibnite, have been defined (Bloomstein et al., 1990). The Getchell and Twin Creeks mines represent major gold orebodies but very little has been published pertaining to mineral paragenesis and the characteristics of ore-forming fluids for these deposits.

Jan 1, 1994

By M. P. Adamson, Bryson D. Trexler, R. V. Ramani, Mark L. Koenig, V. Rajaram, Alan Burton, C. S. Crocker, Kim. Y. C., A. G. Law, William C. Larson

Another record year vas experienced by the mining industry as the value of nonfuel minerals production soared to $23.5 billion-up 15% from the previous year. Based on preliminary estimates by the Bureau of Mines, US mine output was the basis for about $225 billion worth of minerals-derived materials. Metal mining accounted for $8.5 billion, or 36%, of the total. Of the 22 metals produced in the US, 11 showed quantity increases, while 16 had value increases. Business Week's survey of 1200 companies (Mar. 17, 1980, pg. 81) revealed that 21 metals and mining companies had sales increases of 30% with earnings up 104%. Higher prices and increased demand for metals were primary factors behind the improved performance. The steel sector reported a 30% decrease in earnings for the year, but the slump was primarily the result of a $383-million loss for US Steel coupled with a 17% decrease in earnings at Inland Steel. Other firms did well in 1979, with earnings up 279% at Interlake and 269% at Kaiser Steel. Major obstacles facing the steel industry included substantial tonnages of dumped and subsidized imports, environmental expenditures, runaway inflation, and price controls. Turning to nonmetallic production, of the 49 commodities reported by the US Bureau of Mines, 29 had higher outputs and 39 had increased values. While production statistics may seem encouraging, government regulations continued to stifle industry efforts to develop needed new capacity. A case in point may be publication of the Environmental Protection Agency's simplified procedure to streamline five permit programs by consolidating them into one. The five included: hazardous waste management, national pollution discharge elimination, dredge and fill, underground injection control, and prevention of significant deterioration. The new procedure, published by EPA in the Federal Register, took 149 pages. AMC's J.A. Overton, Jr., noted that (MCJ, Nov. 1979, p. 39) to visually depict the complexity of the proposed regulations, Sell Oil Co. developed a flow chart mapping a path through one section. The chart required 10 days to map and two weeks for two draftsmen, using computerized drafting techniques, to plot the results. Overton said, "Perhaps the greatest service EPA has performed in preparing its proposal is to demonstrate again that federal regulations have become a complexity compounded by confu¬sion that culminates in a conundrum." While regulatory agencies promulgate new regulations, the lack of a cohesive government minerals policy remained a matter of significant importance to mine management. A non-fuel minerals study to provide input to the Administration for a national minerals policy program was a dismal shock, according to Rep. Jim D. Santini (D-NV). He said the first phase of the program, which was to identify industry problems, failed to come to grips with the hard decisions necessary regarding these problems, their impact, and their interrelationship. Santini said the report failed to acknowledge government's role in the process and absolved the government of any adverse influence on the domestic minerals industry. In response to the phase one report, eight senior mining executives testified before Santini's House Subcommittee on Mines and Mining concerning mineral supply, access to foreign sources, environmental protection, conservation and recycling, national security, and capital formation. By year's end, Rep. Santini promised to prepare a hard-hitting committee report on problems affecting the non-fuel minerals industry to provide a better base for subsequent policy recommendations (MCJ, Jan. 1980, p. 34). On the technological front, interest again centered on mechanization, automation, and scaleup to improve and expand production. Computer use increased for calculation of ore reserves, mine planning, operations research, and mineral processing.

Jan 5, 1980

By Ethan Steward, Kyle Perry

The study investigates the effects of high-velocity impacts of common mine materials on a reinforced mine seal rated to 120 psi. It found that materials propelled during an underground explosion could generate enough stress to crack or damage seals, even with little visible damage. This highlights the need for careful evaluation of mine seals after any impact or high-pressure event.

Aug 1, 2023

By P. Tsang

The stability of longwall chain pillars depends not only on the mechanical properties of coal and surrounding rocks, but also geological and mining conditions. In order to evaluate the effects of each, variable, the orthogonal experiment design was employed in this study for significance analysis. The study concluded that the stability of longwall chain pillars is mainly controlled by the ratio of pillar stress to pillar strength, the ratio of Young's moduluds of the roof to coal and floor to coal, entry width, pillar width and the internal friction angle of coal. Additionally, horizontal stress, panel width and mining height also play a significant role.

Jan 1, 1994

By Andrzej Wala, Henry P. Cole, Perry David Passaro

Cognitive representations and misconceptions of flow through circuits is an area which has received little attention from science educators, cognitive psychologists, or accident investigators. Misconceptions are also called Aristotelian thinking. They involve a person using primitive unscientific ways of reasoning to make decisions about events (Piaget, 1929; Nussbaum & Novick, 1982; McCloskey, 1983). The use of such primitive concepts leads to errors in reasoning about scientific and technical problems. The existence of misconceptions is well documented among children, adolescents, and adults involved in learning science concepts (Piaget, 1929; Cole & Raven, 1969; Clement, 1982; Mistrell, 1982; McDermott, 1984; Richardson, 1987). Concepts of flow through circuits are important because miners' conceptual errors about these aspects may be, in part, responsible for two fatal mine disasters. On at least two separate occasions, methane gas explosions occurred in underground mines when separate ventilation systems were connected (Elam, Fuller, Carter, Cavanaugh, Fesak & Painter, 1983; Fesak & Cavanaugh, 1984). A review of these disasters indicates that conceptual errors made by miners may have resulted in the accidents (Cole, Wala, Haley, & Vaught, 1987). In this study, co-author Andrzej Wala, stated that his research had "identified conceptual errors that may have caused the miners in these disasters to make fatal mistakes" (Cole et al. 1987), p. 167. Further exploration of these conceptual errors by Wala has led to the hypothesis that misconceptions of basic aspects of flow distribution changes in mine ventilation circuits, are at least, in part, responsible for some mine disasters caused by errors in ventilation systems (Wala & Cole, 1987). Why should these conceptual errors occur? Ausubel (1963) suggested that students come to a new area of study with their own conceptions or preconceptions about how a process operates. Furthermore, these preconceptions may be in conflict with the empirical data from the discipline. In such cases, learning becomes a process in which new concepts must displace or be re-molded from stable concepts that the student has constructed over many years (Clement, 1982). Given the existing research with misconceptions and the work of Wala and Cole (1987), it was hypothesized that experienced miners; either working miners, students of mining engineering, or professional mining engineers, harbored misconceptions about the formal or conceptual aspects of mine ventilation circuits. The misconceptions hypothesized to exist involved flow distribution changes in complex mine ventilation circuits; specifically, how does flow distribution change when a ventilation circuit pathway is altered? Given this information, the following research questions were proposed. Research Questions 1. Do experienced miners and mining engineers harbor misconceptions about mine ventilation systems? This question was addressed by: A. The administration of the Cutthrough Ventilation Arrangements (CVA) exercise that measures subjects' performance level when making decisions about major ventilation changes when connecting two mine sections;

Jan 1, 1989

By Robert A. Haney, Scott G. Vail, Kenneth G. Fields

The Mine Safety and Health Administration, in cooperation with IMC Global Operations, Inc., conducted a joint study to determine the effectiveness of the technology currently in use at the mine to control diesel particulate exposures. IMC Global operates an underground potash mine using diesel-powered equipment to extract minerals. IMC uses a variety of technologies to control worker exposures to diesel particulate. These technologies include: ventilation, low sulfur fuel, oxidation catalytic converters (OCC), maintenance and work practices. The study was conducted over a two-week period, two shifts per day. During the first week (six shifts), baseline data on exposures and diesel particulate emissions were obtained. New OCC's were installed over the weekend on all equipment on the test section. During the second week (six shifts), data were collected to assess the effectiveness of the new OCC devices. In addition to exposure and diesel particulate emissions data, mine ventilation, engine exhaust temperatures and mine operational data were obtained. The primary means of determining diesel particulate concentrations was the respirable combustible dust (RCD) method. Gas concentrations carbon monoxide (CO), carbon dioxide (CO,), and nitrogen dioxide (NO,) were measured using passive dosimeter badges and gas bottles. Results of measurements of diesel particulate, gases, and air- flows were analyzed to determine the effectiveness of airflow and oxidation catalytic converters for controlling diesel particulate exposures. The use of oxidation catalytic converters resulted in reductions of both workers' exposures and diesel emissions.

Jan 1, 1997

By D. W. Smellie

This paper is a review of technological progress in mining geophysics during the past decade. This has been the most significant period in the history of mining geophysics. Among the already existing; techniques, instruments for ground -magnetic and electromagnetic prospecting, were developed that are more, portable and faster to operate. Induced polarization equipment came into widespread use. Airborne instruments of various types became available and were used to survey large areas. Drillhole instruments were developed and have had some use, and it is to be hoped will be used to a greater extent in the future. Two revolutionary new methods, the AFMAG and INPUT, were developed. The wisdom of attempting to cover such a broad field in a single paper might be questioned. There is the inevitable problem that each topic must be discussed very briefly. However, while papers describing individual instruments have appeared, many have yet to be described in the technical literature. The evolution of the ground magnetometer and electromagnetic instruments has not been discussed. It is only recently that a review article has appeared on airborne EM. The existence of review literature on some topics has meant that they are given less emphasis in this review than those topics inadequately covered. It will also be observed that stress is laid on "chose instruments that are generally available to the mining industry rather than those developed by individual exploration companies for their own use.

Jan 1, 1963

By Kirk Carlton

This paper deals with a group of subjects so familiar to all of us that we might question the need for discussion. Even so, nearly every day's business turns up expensive examples of differences in understanding, misdirected assumptions and incomplete technical purchase documents. As our international activities increase, so do these problem areas. Their expense in both money and embarrassment gives rise to this attempt to focus a little extra attention on technical criteria and specifications. The two terms ?criteria? and "specifications" are, we believe, worth separating with respect to meaning. They should not be used interchangeably, although they often are. Criteria are by definition "standards for judging", whereas specifications are "enumerations of particulars". In relation to plant or project engineering, the criteria are the general rules and data which apply to the whole project and the specifications are the further listing of detailed requirements for specific contractual items or pieces of equipment. We'll look a little more closely at specifications after we give another minute or two to this "criteria" subject,

Jan 1, 1973

By James W. Martin, Robert R. Faddick

INTRODUCTION Virtually every sector of society in our country feels the impact of tunnels, either through the transportation of water, commodities, or people. The economic implications are staggering. The Committee on Rapid Excavation (1) reported that during the near future, 1968-1975, underground excavation activity will comprise 946 miles of tunnels (subways: 85 miles; underground urban highways: 123 miles; intercity highway tunnels: 210 miles; water supply tunnels: 528 miles) and 5,119 million tons of crude ore; metals: 874 million tons; nonmetals: 899 million tons; and coal: 3,346 million tons. It is estimated that the cumulative demand for underground excavation in the decade 1970-1979 will be 13 billion dollars for construction-oriented demand and 16 billion dollars for mining-oriented demand. The respective figures for the decade 1980-1989 are estimated at 22 billion dollars and 18 billion dollars. Of the many advantages claimed for tunnels (2, 3, 4, 5) the environmental considerations are becoming increasingly important. Transportation tunnels particularly for rapid transit systems, offer reductions in noise pollution and air pollution while improving aesthetics and optimizing land use (fewer problems of right-of-way and disruption of utilities). Considerable interest has been shown recently in sub-surface construction and mining (6, 7, 8). Recognizing the future demands for tunnels has led to considerable study of methods to improve rates of tunnel advance per day, safety, and the overall economics. The search for higher rates of advance has Led away from what has heap termed conventional methods (drilling

Jan 1, 1974