Search Documents

By B. F. Westfall

Throughout the 1960's and 1970's world trade grew rapidly, reaching a peak of USS1.8 trillion in 1980. Since then the world recession of the early 1980's shrunk trade to about US$1.6 trillion. The reduced cash flow to developing economies made it difficult to service their huge international debts, Nowadays lenders are reluctant to grant Third World countries additional credit. The shortage of export financing, plus trade barriers set up by developed countries, is further inhibiting international trade. Therefore, countries are turning to new and creative alternatives to financing imports of consumer as well as of investment goods. Non-cash transactions, including different forms of countertrade, are rapidly growing alternatives to traditional trade financing patterns. In 1983 about 30% of international trade, or close to US$600 bill ion, were presumably done by non-cash transactions, up from barely 2% in 1976. By year 2000, half the world trade is likely to be conducted on basis of barter. As of mid-1984 some 88 nations used countertrade regularly and Governments of at least 15 Latin American countries had arranged or mandated commercial countertrade.

Jan 1, 1986

By Brij M. Moudgil

Flotation was introduced in phosphate rock processing in the late twenties and since then it has been an important part of the concentration process. More than two thirds of the rock produced in Florida is upgraded by the flotation process. Since no crushing or milling steps are involved in the material preparation, the flotation plant feed is coarser than in most other mineral flotation systems. During hydraulic processing of the rock, particles in the size range of -14, +150 mesh constitute the flotation feed. This size fraction is further classified by hydraulic sizers, stationary screens and vibrating screens into a coarse (-14, +35 mesh) and a fine (-35, +150 mesh) flotation feed. The flotation techniques for concentrating the fine feed as practiced by the Florida Phosphate producers have been standardized over the years, however, methods for upgrading the coarse feed differ from plant to plant. In this paper an effort has been made to present relative merits of the techniques employed for concentrating the coarse phosphate rock..

Jan 1, 1977

By L. B. Kirk, A. R. Kirk

At New World, Au-Cu-Ag mineralization occurs in stratiform car-bonate-hosted, massive sulfide-iron oxide, and skarn-replacement deposits. Regional pyritic-alteration, local massive sulfide mineralization and mine wastes generate acid drainage within the district. Water quality improves down gradient through dilution and mixing of acid and metal-rich mine water with bicarbonate-rich, low-metal surface and groundwater, and precipitation of metal-rich ferrihydroxide phases. Natural deposits of ferricrete indicate that pre-mining ARD has occurred, providing important clues to pre-mining water quality. The geoenvironmental model identifies the Cu-skarn mineralization as the primary target for ARD management. Closure success will be limited by the geoenvironmental nature of the natural mineralization.

Jan 1, 2004

By Florence Munter

This paper provides a discussion of the various federal and state laws governing water quality as related to mining operations. The specific laws addressed are the Clean Water Act, and the Arizona Mined Land Reclamation Act. Topics that will be addressed are mine water and process water discharges, storm water discharges, pollution prevention, dredge and fill, spill prevention control and countermeasure plan, and surface water protection. Proposed changes to the laws and regulations will be discussed. Compliance strategies will be suggested to prevent potential noncompliance and enforcement.

Jan 1, 1996

By James L. Patton

Automation of mining increases the productivity of labor, thereby reducing the unit cost of labor. Such cost constitutes the largest portion of the direct or variable costs of producing coal. Therefore, any increase in productivity directly reduces variable cost. The large investment in mechanical equipment carries with it the burden of increased fixed charges. As the proportion of fixed cost to the total cost increases, the effects on the cost of production changes are amplified. Therefore, equipment must be fully utilized at all times. Averaged fixed costs rise with any decline in production. Such a situation forces coal companies to seek every means of main¬taining full production. Figure I will reflect the story on the relationship of production to cost.

Jan 1, 1962

By N. Zouridakis

Radon is an established lung carcinogen and remains the most important environmental radiation exposure. It was estimated that inhalation of radon and its short-lived decay products accounts on average for about one half of the effective dose equivalent from all natural sources of radiation. Radon contained in household water can transferred into room air as a result of agitation or heating. An indoor air concentration of 400 Bq/m3 is obtained if the radon concentration in household water is 4 kBq/L. A typical concentration of radon in ground water is about 1000 times lower than this concentration but sometime elevated concentrations of some kBq/L in ground water are reported. In this work a Liquid Scintillation counting system is used to obtain fast and accurate measurements of radon (222Rn) in water samples from Argolida, Greece.

Jan 1, 2007

Effective ground control in the gate entries, particularly in the tailgate travelways, is essential for safe longwall mining. Longwall pillars maintain gate entry stability and carry abutment loads. To answer the need for effective longwall pillar design, an empirical method called Analysis of Longwall Pillar Stability (ALPS) was proposed several years ago. Some recent research at the Bureau of Mines has focused on the refinement and verification of the ALPS method. ALPS was originally developed from field studies in which multiple stressmeters were installed in longwall pillars and monitored during mining. Several new field studies have now been incorporated into the ALPS data base. The field measurements have' been used to verify formulas for predicting abutment strength and pillar loads, and to develop an expression for the distribution of the abutment load.

Jan 1, 1989

By T. Rockley, B. Goertz, S. McDaniel, J. Brune, K. Bakhsh

"Researchers at the Colorado School of Mines, under a project funded by the Alpha Foundation, have developed a working prototype of a dust sample collection device designed to determine if sufficient rock dust has been placed in an underground coal mine to prevent coal dust explosions. When used in conjunction with the Coal Dust Explosibility Meter (CDEM), the device will provide near instantaneous results on the quality of rock dusting at the tested location. The sampling device applies a pulse of air to a testing surface and collect a representative sample of mine dust based on the pneumatic entrainment process during a mine explosion. The use of both physical testing and Computational Fluid Dynamics (CFD) modeling has allowed researchers to refine the design to accurately represent the particle entrainment and optimize the sample size collected for the CDEM. The prototype is being tested in a mine environment to produce information of usability and practical aspects of mine dust sampling. This paper is a progress report summarizing the current status of sampler development. Researchers expect to have a fully developed and tested sampler in early 2016. INTRODUCTION Underground coal mines face the danger of methane and coal dust explosions. The disaster at Upper Big Branch mine (2010) has demonstrated the impact of a violent coal dust explosion that fatally injured 29 miners. Reviewing the history of coal dust explosions, researchers found that that mine operators and mine inspectors do not have a reliable method of collecting dust samples to assure that sufficient amounts of rock dust have been places to inertize the coal dust. This is a problem specifically with small mines that do not have dedicated safety departments to track rock dusting work. The aim of this research is to develop a simple, portable device that can help underground mine examiners collect dust samples from workings and test the explosibility of the sample near instantaneously. Researchers determined that the current brush-and-pan sampling method required by MSHA (MSHA 2013) is flawed in several aspects: Mechanical sampling with a brush exerts forces on the mine dust that may differ significantly from those present during an explosion. Also, U.S Bureau of Mines research (Nagy 1965) has determined that only the top 0.125 inches of the mine dust layer will be entrained in a coal dust explosion. Using a handheld pan and brush, it is difficult to correctly and repeatably sample a layer of this exact thickness. The following will describe the CFD modeling and experimental testing for the development of the prototype sampler. Researchers analyze the accuracy and performance of the prototype during the course of the build process."

Jan 1, 2015

By T. Cantwell

Techniques useful in operations, analysis are applied to the problem of planning an exploration program. The model used treats mineral exploration as a Markov process, and maximization of gain is the criteria determining the optimum program. The mathematical description of the model and the optimization are first worked out. Application of the mathematics to several simple examples is given. Finally, comparison of the data necessary to use this operations analysis with the available data shows that the method can only be a guide to planning an exploration program.

Jan 1, 1962

By D. Goffaux

In less than two years, Stratmin has discovered, explored, developed, financed and put into production by open pit, a large graphite mine. The deposit, hinted by airborne electromagnetic survey, was discovered in September 1987 through various ground geophysical surveys, diamond drilling and trenching. The open pit started production in February 1989, feeding a nearby leased mill at Notre-Dame-du-Laus (Quebec), having a processing capacity of 400 tons per day. A new 1,000 tonne per day mill was built at the mine site, in Lac-des-lies (Quebec) and began production in April 1990. The Lac-des-lies graphite operation is currently one of the largest of its kind in the world. Mine and mill facilities are operated by Stratmin Graphite, jointly owned by Stratmin Inc. (75%) and Imetal-France (25%), a wholly owned subsidiary of Imetal (France). From initial exports limited to Japan and United States, Stratmin Graphite is now exporting in fourteen different countries, attesting to the very high quality of its products, with grades ranging from 92% to 97% carbon. Among the numerous graphite deposits discovered in Canada, Stratmin Graphite Inc. has emerged as the leader and virtually the sole crystalline graphite producer in North America, operating on a continuous basis.

Jan 1, 1992

By Robert C. Meaders

In this paper, autogenous grinding is defined as the combined crushing and grinder of a run-of-mine ore or the product from a primary crusher, in a single stage grinding mill. This is in contrast to pebble milling where pebbles are substituted for steel balls to grind a ball mill size feed. The autogenous mill to compete in efficiency with normal methods of crushing and grinding must not use greater power, must use less labor and steel, and must produce an equivalent product.

Jan 1, 1963

By Rainer Alles, Markus Keller

INTRODUCTION For overland conveyors of several kilometres length and as well as wide for conveyors designed for high mass flows, the cost for the conveyor belting share is 40% to 50% of the invested cost 173. The German Standard DIN 22101 is used for calculation and dimensioning of - conveyor belts and belt conveyor components. Developments in rubber technology and conveyor belt design required a revision of the standard released in 1982 121, which was published in August 2001 131. New research results and publications 16-9, 13-15] led to a better understanding of the material behaviour and their influences on conveyor belts. Test and calculation methods have been established to determine the most important parameters which are related to the performance of a conveyor belt line. These parameters are • The running resistance of the idlers • The indentation resistance of the belt • The dynamic splice efficiency • The distribution of belt load in the splices, transition zones and on pulleys. As a result, new rubber compounds with low indentation losses allow the use of reduced friction coefficients and thus lead to reduced power consumption, smaller drives and lower belt tensions. The deeper understanding of the flux of forces within belt splices led to both optimised splice design and optimised rubber compounds which significantly improve the dynamic splice efficiency. Therefore, in accordance with the standard, the benefits of these technologies and the better understanding of material behaviour allow a reduction of belt strength still maintaining sufficient safety factors. Thus engineers are enabled to calculate belt tensions more exactly and users are encouraged to pay more attention to starting and braking techniques. DETERMINATION OF DRIVE FORCE According to the DIN standards the resistance to motion generally has to be determined for each different section of the belt conveyor including upper and lower run separately. The necessary drive power P is calculated as [ ] with v as the conveying speed. The total of all resistances to motion of carry and return run can be determined as [ ] FHo and FHu are the primary resistances consisting of the running resistances of the idlers, the indentation resistance of the belt, the fulling of the conveyed material and the flexure of the belt. While indentation resistance and idler resistance are measurable, they have been deter- mined to be responsible for up to 70% of the primary resistances covered by FH. Further FN is the secondary resistance that covers, for example, the resistance of feeding points and scrapers. Fa are the total slope resistances and Fs is the total of all special resistances, resulting, for example, from belt steering devices. These three resistances should be neglected in the following discussion. For conveyors where a determination of the substantial parts of the resistances to motion is not possible, according to the new DIN standard [31 a determination of the drive power is acceptable by using the fictitious friction factor) [ ] In this formula the index i identifies the individual section of the conveyor, 1 is the length of the section and MR, MG and ML are the related masses of the idlers, the belt and the load in kg/m. The fictitious friction factor f determines the ratio between the overall resistance to motion and the total of moved masses within the

Jan 1, 2004

By Bob Gordon, Allen Furth, Dan Dobbels

A 4.8 m (16 ft) diameter hard rock tunnel was driven through granite bedrock to create the 1.7 kilometer (1.1 mile) long Hampton McCloy Retention Tunnel for the city of Richmond, Virginia. During the work the tunnel encountered narrow seams of partially decomposed granite that were not self supporting and could be dealt with using ribs and lagging. However, as the tunnel approached the receiving shaft, it encountered a large seam of highly decomposed rock, alluvial deposits and running sand which resulted in soil loss into the machine. As a result of this condition, a jet grouting program was quickly developed to allow the tunneling to continue. This paper will describe the manner in which jet grouting was used to solidify and stabilize the decomposed bedrock, alluvial soils, and running sand to allow the TBM to continue tunneling.

Jan 1, 2003

By William W. Shriver

When the Henderson Project is completed in 1975, it will become one of the Free World's largest primary molybdenum producers. The Henderson Mine will be located approximately 50 miles west of Denver, Colorado, on the eastern slope of the Continental Divide. Ore reserves are currently estimated to be 303,000,000 tons with a grade of 0.49% MoS2. The mill and tailing area will be located approximately 14.5 miles from the mine in the Williams Fork Valley, which is on the western slope of the Continental Divide. Ore haulage from the mine to the mill will be by ten miles of underground railroad and 4.5 miles of surface railroad. The concentrator has been designed to mill 30,000 tons per day and will yield approximately 50,000,000 pounds of contained molybdenum per year. This paper is concerned with the tailing and water supply system for the Henderson Project and in particular the environmental considerations affecting their design.

Jan 1, 1970

By Z. F. Wang, W. K. Choi, A. E. Torma

The present study has investigated the bioleachability of low-grade and high-grade pyritic gold ores and the extraction of gold from the leach residues of bioleaching with thiourea solutions. Final gold extractions as high as 96% were obtained from the high-grade ore and above 93% from the low-grade ore. The gold extraction was found to follow the extent of pyrite biooxidation. Using a cyclic voltammetric technique and carbon-paste-FeS2 electrode it was found that the semiconductor pyrite oxidation involves many intermediate electrochemical reactions. Furthermore, the oxidation is solid-state diffusion controlled as suggested by chronoamperometric and chronopotentiometric measurements.Using Sand's approach, the activation energy of solid-state diffusion biooxidation of pyrite was determined to be AEa=22.4 kJ. A generalized model for the mechanisms of pyrite oxidation has been presented.

Jan 1, 1990

Slurry technology developed for the marine transport of mineral commodities has been increasingly applied to on-shore slurry transport systems. Reclaim of mineral concentrates, sand tailings for mine backfill and various industrial minerals from storage tanks or ponds normally require a slurry of high density at constant flow rates to improve process performance and to reduce handling costs. An efficient system must accomplish this at minimum capital costs with maximum reliability. Continuing improvements in equipment design to improve repulping efficiency and their application are discussed.

Jan 1, 1986

By Yan. T. Y.

Uranium precipitation from an eluate using hydrogen peroxide has been studied in a laboratory continuous unit. The important process parameters were the dosage of H2O2, reaction pH and chloride ion concentration. In the process, the alkaline eluate is acidified to a pH of 2, then H2O2 at 110%-130% of the stoichiometric requirement is added, and finally NaOH is added to maintain a pH of 4 for one hour to complete the precipitation and settling. The chloride content in the system is controlled to 50g/L or below by rejecting part of the decant solution. The process has been successfully employed in commercial operations. The uranium recovery is complete, while the precipitate settles rapidly and can be processed to high purity yellow cake without filtration.

Jan 1, 1991

By Enrique Farjeat P.

Mexico City's growth has encourage development of underworks to meet drainage and transport requirements. Deep Drainage System has been constructed through a complex tunnel network, 108 km in total, varying from 30 to 12 m in depth and 6.24 or 4.00 m in diameter. Wide range of stability conditions presented in soils has forced the use of several tunnelling methods, going from the manual procedure by the use of pneumatic tools, to slurry shields, or open face shields, with the aid of or without compressed air. For transport, subway tunnels have been excavated in very compact silty sands, 9.15 and 9.51 m in diameter, with the use of open shields one of which was designed by Mexican engineers as a prototype machine. This paper tries to describe evolution of tunnelling methods used in Mexico City during last 20 years.

Jan 1, 1991

By R. P. King

A new device, called the dual impact load cell, has been developed and built at the Comminution Center to measure fracture energy and damage accumulation in brittle particles that are subject to impact. The results show that damage accumulation during impact is not a significant factor in determining the fracture energy or the particle strength. However, predamage induced by thermal pretreatment of the particles has a significant effect on both fracture energy and particle strength.

Jan 1, 1995

By Thomas Gleason

Wet scrubbing of fine coal from Thermal dryers poses a number of problems in adapting the gas cleaning equipment for required clean-up of the fine particulate matter. Among then are: 1. The dust In the gases leaving the Thermal dryer cyclone-s is often extremely fine with high percentages of the total dust loading less than one (1) micron in size. 2, The flue gas entering the scrubber is corrosive since the coal fired in the thermal dryer furnace is in the range of 0.7% by weight sulphur or higher. Therefore comparatively high cost stainless steel alloys or corrosion resistant linings are required for a satisfactory service life. 3. Requirements for residual coal loadings leaving the gas e scrubber are continually being lowered while modern coal preparation operation is imposing heavier burdens on the collection system through introduction into the Thermal dryer system of very fine coal previously not recovered. The advent of flotation systems in increasing numbers is typical of this trend 4. The installation of a scrubbing system on Thermal dryers is made primarily to reduce air pollution and product recovery value is of little or no value. Therefore the operating costs, that is, of gas pressure drop and water requirements must be held to a minimum.

Jan 1, 1962