Search Documents

By J. Noll, E. Cauda, T. Barone, S. Vanderslice

Measuring diesel particulate matter (DPM) for underground metal/nonmetal mine compliance samples is done by collecting DPM onto quartz fiber filters and analyzing the samples via NIOSH method 5040 for elemental carbon (EC) and total carbon (TC). As part of the sampling train, two quartz fiber filters in tandem are housed inside an SKC DPM cassette that includes an impactor. The impactor segregates DPM and mine dust, and the second filter is used to correct for adsorption of vapor phase organic carbon (OC). Since the value of the second filter is subtracted from the first, the pre-existing carbon on the filter media for both filters needs to be comparable. In addition, the pre-existing carbon on the media should be low for accurate and sensitive results. However, there have been some reports of elevated OC on the filter media of the SKC DPM cassettes, which would cause the limit of detection (LOD) to be higher than reported at times. In this study, blank SKC DPM cassettes from different batches and with different expiration dates were analyzed to quantify the amount of carbon on the filter media and to determine the LOD and limit of quantification (LOQ) associated with these samplers. It was found that the organic carbon and total carbon on the media was about five times higher than quartz media used in samplers from other studies. The average TC on the blanks was 2.57 μg/cm2 with a standard deviation of 0.70, resulting in a LOD of 21 μg/m3 TC, 8-hr Time Weighted Average (TWA), and LOQ of 69 μg/m3 TC, 8-hr TWA, when using these samplers for collecting DPM. The LOD and LOQ may be improved through some sample preparation techniques. INTRODUCTION Exposure to diesel exhaust (DE) is associated with an increased risk for lung cancer and other adverse health effects (Attfield et al. 2012, Silverman et al. 2012, Ping and Guang 2017, IARC 2012). Pronk et al. 2009 reported that the highest exposed groups to elemental carbon (EC) from DE worked in underground sites in mining and construction and they were exposed to concentrations between 27–658 μg/m3. At concentrations (1–25 μg/m3 EC) well below those observed in mining, diesel particulate matter (DPM) exposures were estimated to increase the risk of cancer by levels exceeding those typically acceptable for occupational risk in the United States and Europe (Vermeulen et al. 2014). This suggests that underground miners are especially at risk because of their more substantial exposures in confined working spaces. As a protective measure, in 2001, the Mine Safety and Health Administration (MSHA) promulgated a rule to limit exposures of metal/nonmetal underground miners to DPM to an 8-hr time-weighted average (TWA) of 160 μg/m3 total carbon (TC) (MSHA 2001, 2006).

Jan 1, 2019

By George E. Aiken

Agglomeration developments in the iron ore industry of North America are closely related to shifting patterns in commercially acceptable ore grades and even the definition of iron ores. These relationships have occurred mainly during the last 20 years. Many of these changes are an outgrowth of events which involved the history of the Mesabi Range. Although magnetic taconites had been discovered in the Lake Superior area about 1870, they remained unworked in part for lack of concentration methods and a generally unfavorable economic climate. Some 20 years later the rich Mesabi hematites were found beginning the era of direct shipping ores which continued through World War II. These Lake Superior iron ores included reserves of an estimated three billion tons. Following World War II, decreasing ore grades and rising costs began to force the closing of many underground iron mines. The early 501 s saw the beginning of the decline in direct shipping ores and a spurt in production of natural iron concentrate s. However, the market for unprocessed concentrates began to decline in the early 601 s as agglomerated products and foreign ores began to dominate the U. S. market.

Jan 1, 1972

By Norman L. Kotraba

In Electric Arc Furnace (EAF) steelmaking, dust emissions are collected in a baghouse to prevent their escape to the Environment. This fine dust, predominantly iron oxide, also contains oxides of various other metals introduced into the EAF from the scrap charge. For example, mixed or galvanized scrap brings with it zinc, lead, and small quantities of cadmium which preferentially accumulate in the collected off-gas dust. Stainless steel scrap brings chromium into the charge, some of which also makes its way into the baghouse dust as hexavalent chromium-containing oxides. Because many of the contained heavy metal oxides are water-leachable, the U. S. Environmental Protection Agency has listed EAF dust as a hazardous waste which, as of August 8, 1988, cannot be 1andfi11ed without first being treated. Moreover, beginning August 8, 1991, all dusts with zinc concentrations of 15% or greater will be required to undergo high temperature thermal treatment to remove the heavy metals prior to any further disposal. This deadline represents several EPA-granted time extensions to the original requirements; extensions which were granted to allow for further development of process technologies.

Jan 1, 1991

By C. G. Janes, N. Finkelstein, L. M. Jr. Johnson

In May, 1966, the General Services Administration (GSA) announced a program to encourage additional domestic production of copper in the interest of national security. Upon learning of the copper production expansion program, Duval Corporation entered into negotiations with GSA for development of the Sierrita copper-molybdenum property under the program. Agreements between the GSA and Duval Sierrita Corporation, a wholly owned subsidiary of Duval Corporation, were concluded in 1967, with the Sierrita Concentrator beginning operation in 1970 at a designed capacity of 72,000 STPD. Subsequent additions and modifications have expanded capacity to 90,000 STPD. This property, located approximately 20 miles south of Tucson, Arizona, represents an investment including working capital of about $200 million. These funds were provided from an $83 million loan from GSA, repayable in copper valued at 38 cents per pound, $48.75 million of bank loans subject to U. S. Government V- loan guarantees, and Company capital contributions. Current general operating statistics for the concentrator are listed below: Ore Grade 0.32% Cu., 0.030% Mo. Daily Tons Milled 90,000 STPD Annual Copper Production 94,600 Tons Annual Molybdenum Production 15,000,000 Lbs. Annual Silver Production 1,135,000 Ounces

Jan 1, 1976

By Aldo F. Barsotti

The production and consumption of industrial minerals in the United States traditionally have played important roles in mining and in the supply of the bulk of basic raw materials to the economy. This diverse group of minerals extracted and consumed by a variety of industries accounts, on a weight and volume basis, for most mineral-based products consumed in our economy. Industrial minerals form the bulk of the basic raw-materials feedstock for most of the construction, agricultural, and inorganic-chemical-manufacturing sectors, and a good portion of the transportation, manufacturing, organic chemical, and service sectors of the U.S. economy. In this presentation, I discuss current estimates of the amount and value of industrial minerals mined compared with all mining in 1997. I then present a summary of 1997 production of industrial minerals by several end-use industries. This is followed by a historical perspective of the consumption of industrial minerals as a subset of all basic materials, with special emphasis on the aggregates industry. The presentation concludes with a look at the geographic distribution of industrial mineral operations in the United States and some thoughts about the future.

Jan 1, 1999

By A. D. Davis, C. J. Webb

Brohm Mining Company's Gilt Edge Mine in the northern Black Hills was a surface heap-leach operation that was active from the 1980s until 1999. Financing problems and acid drainage concerns at the mine were reported in the late 1990s. In February of 1999 the Governor of South Dakota announced plans to request the U.S. Environmental Protection Agency to help clean up acidic water at the mine and reclaim the site. In July 1999 the parent company of Brohm, Dakota Mining, filed for bankruptcy in Canada. Because of the bankruptcy and environmental problems, the State of South Dakota intervened and began water treatment. The mine was declared a Superfund site in 2000. Hydrologic issues include the potential for acidic drainage from the site. The mine is at the headwaters of Strawberry Creek, which drains into Bear Butte Creek. About four miles downstream, Bear Butte Creek loses its discharge to swallow holes in the karstic Madison Limestone aquifer, a regionally extensive and valuable ground-water reservoir. Other concerns at the site include treatment of acidic water in mine pits and a waste rock dump.

Jan 1, 2002

By Gregory P. White

A number of private companies and universities have developed computer programs which can be used to simulate surface coal mining by dragline. In this paper, we briefly discuss the concept of computer simulation, compare these computer programs with each other, describe the major changes required to convert these programs to an IBM computer system, and analyze their sensitivity to inaccurate input data. We also present a summary of the required data input for each program, core storage requirements, and output results. Sources for obtaining these programs and their documentation are listed at the end of the paper.

Jan 1, 1983

By Kathy Kalenchuk

To develop strategic and tactical strategies to manage seismic hazard in a safe and economic manner, it is necessary to understand the spatial and temporal distribution of mine wide seismogenic behavior. Global mine-scale numerical stress modelling provides a means to forward predict seismic susceptibility thereby facilitating informed decision making for the development and implementation of strategic and tactical risk mitigation measures. To make forward predictions of hazard susceptibility using global stress models with reasonable confidence, it is necessary to rigorously calibrate numerical stress models to the observed history of ground reaction. This paper demonstrates quantifiable methods for calibrating numerical models and developing probabilistic prediction criterion using seismic data. The appropriate applications of model inputs (including boundary conditions, constitutive models and material parameterization) specific to global mine-scale modelling are also discussed. Lastly, this paper demonstrates how the calibration process adds value not only to informed decision making, but also to the improved understanding of site geomechanical conditions; including enhanced identification of geotechnical domains and mechanical indicators required for seismic mechanism domaining.

Apr 26, 2022

By C. L. Karr

Researchers at the U. S. Bureau of Mines have developed a technique for producing adaptive control systems using fuzzy logic and genetic algorithms. These controllers can be used to efficiently manipulate complex systems in real-time. Furthermore, they can achieve an acceptable level of control despite limited feedback in the problem environment. The control systems that result from the implementation of the Bureau-developed technique are able to recognize when changes have occurred in the problem environment, evaluate the magnitude of these changes, and alter the strategy being used to control the problem environment. Fuzzy logic is used to provide the controller with a rule-base that mimics the "rule-of-thumb" approach generally adopted by humans in the area of process control. Genetic algorithms are used to provide the controller with the adaptive capabilities necessary for the control of complex time-varying processes popular in the minerals processing industry. The effectiveness of this technique is demonstrated on a laboratory pH titration system. The pH system includes a changing setpoint, titrants with varying concentrations, and the possible addition of a buffering solution.

Jan 1, 1993

By J. E. Murphy, R. Y. Wan, K. R. Sandgren, M. C. Fuerstenau

As part of a U.S. Bureau of Mines program to evaluate alternatives to sodium cyanide in gold leaching, three organic nitrile compounds were tested for their effectiveness as gold lixiviante. The organic compounds examined were malononitrile, acetonitrile, and cyanoacetamide. The reagents were tested on an oxide ore, two carbonaceous ores, and a eulfidic ore. Acetonitrile and cyanoacetamide were shown to be ineffective gold leachante. Malononitrile was the most successful of the organic lixiviants. On an oxide ore, malononitrile performed shilarlyto sodium cyanide with extractions of around 80 pct. For carbonaceous "preg-robbing" oree, sodium cyanide was completely ineffective while malononitrile extracted 24 pct of the gold. When using a resin-in-leach technique, extraction with sodium cyanide increased to 60 pct and the extraction with malononitrile increased to 80 pct. On the sulfide ore, sodium cyanide and malononitrile performed similarly with 80+ pct extraction as long as the pH of the malononitrile solution wae maintained above 10.5. Malononitrile is six times less toxic than sodium cyanide as measured by LD, levels. Therefore, malononitrile has a significant advantage over eodium cyanide, but its high cost and undemonstrated usefulnees make it unlikely to gain acceptance.

Jan 1, 1993

By Richard J. Adams

Coal jigs have played a predominant role in U. S. coal preparation for fifty years. Recently, an improved fine coal jig has been used to prepare the middle size range coal. These efficient machines are changing the historical thinking about jigs and is consistent with trends in coal preparation throughout the world. The performance achieved and operating cost savings are causing a change in fine coal cleaning strategy. With the exception of a handful of operators, fine coal jigs are generally not well understood by the industry. The objective of this paper is to provide some insight into the past use of fine coal jigs and their potential in the future. Improved Fine Coal Jig Since the mid 701s, an improved fine coal jig has been employed to an important niche in preparation, the 19 mm x 100 M range of cleaning. Several factors due to mining and liberation considerations have caused an expansion of this middle range of coal resulting in a host of challenges for coal preparation engineers. Fine coal jigs have been commissioned in several installations in North America to handle these important applications as shown in Table No. 1.

Jan 1, 1988

By M. Deniz Turan, HASAN NIZAMOGLU, Z. ABIDIN SARI, Tolga Depci

Chalcopyrite extraction in an aqueous acid medium occurs through solid transformations into distinct intermediaries. As intermediates, mineral phases CuS, Cu2 S and Cu5 FeS4 may generate in the leaching solution before CuFeS2 completely decomposes to Cu2+, Fe2+ and S0. Oxalic acid is a common organic acid, and it dissolves easily in warm water. Due to the chelating feature of oxalic acid, it hinders iron precipitation by composing soluble complex anions in a wide range of pH. In this study, recovery of copper from solid material (obtained by leaching of chalcopyrite with oxalic acid in the presence of hydrogen peroxide) with a copper oxalate structure was carried out selectively using hydrochloric acid (HCl). Selective recovery of copper by degrading the copper oxalate structure with a low-solubility product (Ksp= 4.43 × 10 −10) was performed by conventional leaching in the presence of HCl.

By Liming Yuan, Wei Tang, RICHARD THOMAS, JOHN SOLES

Lithium-ion (Li-ion) battery pack fires pose great hazards to the safety and health of miners. A detailed experimental study has been conducted at the National Institute for Occupational Safety and Health’s (NIOSH) Pittsburgh Mining Research Division (PMRD) to investigate the effectiveness of different fire suppression systems on Li-ion battery pack fire extinguishment. Tests were conducted in a well-ventilated container. Two sizes of battery packs (12 V and 24 V) were heated by heater strips to trigger thermal runaway and fire. Water mist with different flow rates, ABC powder, type D dry chemical, and water mist with F500 additives were used as the fire suppression agents. Multiple thermocouples were installed on the battery packs to measure the temperature evolution during the tests. The results indicate that the water mist with F500 additives is the most effective suppressant among the agents tested. Dry chemicals, however, do quench the fire for a moment, but cannot prevent re-ignition of the battery since they do not provide enough cooling. The findings of this paper can be used to develop safer battery fire suppression techniques in mining environments.

Jan 1, 2024

By A. Probst, N. Moores, J. A. Finch

In 1994, McGill University and INCO Ltd. (Sudbury operation) initiated the transfer of technology originally developed to detect levels in equipment ranging from flotation columns to thickeners. A conductivity probe was installed in a concentrate thickener to monitor the mud line and the solids load. The probe consisted of a vertical tube with 32 equally spaced electrode rings connected in pairs to give 31 conductivity cells. Conductivity was measured as a function of depth to produce a conductivity profile. From the conductivity profile, the mud line and the percent solids can be inferred. The probe was installed in October 1994, and it has been successfully detecting profiles since then. This paper includes a description of the incidents that occurred and the experiences gained during this technology-transfer process. Discussed is probe installation and startup; software modifications to accommodate both operating conditions and the needs of the operators; and calibration procedures to adjust to changes in performance as a consequence of long-term use. Also included are preliminary observations of the still-in-progress last stage, i.e., signal interpretation and use to facilitate operation, particularly by providing early reaction to upstream disturbances.

Jan 1, 1999

By A. A. El-Midany, R. M. Farag, A. M. Salem, S. E. El-Mofty

Bentonite is one of the main players in the stability of drilling mud. Its particle size and particle size distribution significantly affect drilling mud’s rheological properties. Although the Specifications for Drilling Fluids Materials report on Oil Companies Material Association (OCMA)-grade bentonite states that the API recommended powder having 2.5 percent mass fraction as the maximum value of residue of diameter greater than 75 μm, there is no other information on the specific size distribution for API bentonite. It was found that API bentonite has a specific size distribution with specific mixing weights. It is important to investigate why that mixture represents the optimum properties of drilling mud and how each individual size fraction has a specific function in the mixture. To clarify the effect of individual size as well as the collective effect of the size distribution, API bentonite was classified into different size fractions, with each tested separately for controlling properties such as filtration loss, plastic viscosity, gel strength, cake thickness and packing density.

By Hugh Boyd

Jet pulverization is a relatively new tool for fine grinding. It is not yet in general use in the mining and ore dressing fields, since most of the requirements in these areas have been for relatively coarse particle sizes. As the need for finer grinding increases - because of different ores, new products, and new values being sought - jet pulverization will, increasingly, be properly used.

Jan 1, 1969

By David Brown, Adrian St. John, John Comins, Mike King

"INTRODUCTION The Crossrail project provides an East-West link across London enabling an additional 200 million journeys each year linking up major business centres and existing transportation interchanges, while reducing congestion at street level and within the current underground system. The project has built major structures in Sprayed Concrete Linings (SCL), including 5 new stations, 6 crossover caverns and numerous passages, adits and ventilation tunnels. Construction has taken approximately 4 years, and has involved the spraying of over 200,000m3 of concrete. At the start of the project there was a lack of available records from previous projects concerning concrete falls, which hindered risk assessments and the ability to make meaningful comparisons around spraying or material performance. This paper redresses this lack of data by providing information on falls experienced on this project and makes recommendations to assist future projects. Construction Methods Table 1 below summarises the main contracts with elements of permanent SCL. The listed primary lining lengths include pilot tunnels, side drift tunnels and enlargements as separate tunnels.A range of construction sequences were used in order to deal with the design requirements, geometry, and the ground and ground water conditions. The following briefly summarises the build up by layers, with typical design dimensions provided for a platform sized tunnel (approximately 9m internal diameter), excluding tolerance allowances. Some linings were sprayed in more than one layer to allow for inclusion of reinforcement layers or to avoid a too aggressive build-up of thickness: •,Initial shotcrete, or sealing, layer (ISL) of 75mm followed by a Primary Lining (PL) of 300mm. •,Regulating layer of 40mm followed by a Waterproof membrane (Sprayed membrane, 3-6mm). •,Secondary lining (SL) of 250mm with a separate sprayed fire protection layer (FPL) of 50mm."

Jan 1, 2016

By R. J. Morrell

The Bureau of Mines, U.S. Department of the Interior, has developed a hardrock cutting concept and incorporated it into an extraction system called the ripper miner. This concept uses a single, wide bit that attacks the rock at a shallow angle and slow speed. Research has demonstrated that the system is capable of excavation rates exceeding those possible with conventional drill-blast and can effectively cut rock too hard for conventional roadheaders or continuous mining machines. It has the additional advantages of low bit wear and dust generation. This highly flexible concept is applicable to both mining and driving development openings and can cut any material from coal to hard rock. A single rip-per miner can perform the functions of a continuous mining machine, a roadheader excavator, and a tunnel boring machine. This paper presents the history of the development of the ripper miner from the initial laboratory tests through the construction and testing of the full-scale, lab prototype. It includes a comparison of the ripper miner to systems currently used from the standpoint of energy efficiencies and operating costs.

Jan 1, 1989

By C. A. Roberts

What are the benefits and limitations of financial analysis software as a decision making tool in the mining industry? Traditionally, the assumptions and simplifications imposed by complex and uncertain information have been viewed as the main obstacle to reaching an optimum decision. Recently, however, phenomena such as corporate culture and power structure have received increasing attention as significant influences on organizational decision making processes. Studies of these phenomena have suggested an alternative way of understanding decision making processes and an alternative view of the role played by computer analysis in such processes. This paper presents these two views of decision making, and examines what each implies about the role of financial analysis software as a decision making tool in the mining industry.

Jan 1, 1992

By Marc Carriere

Bright-orange couplings adorning piping systems are a common sight in just about every underground mine in North America. Grooved mechanical piping, the pipe-joining system that utilizes these couplings, is the preferred method for joining underground and plant piping systems in the mining industry, due to the ease and speed of installation and maintenance. However, the applications for such systems have traditionally excluded high-pressure systems. Most grooved mechanical couplings have a moderate working-pressure limitation, so high-pressure systems have required the use of alternative joining methods, typically heavy-duty flanges. However, the introduction of high-pressure couplings (up to 4,000 psi) has made the grooved joining method viable, and even preferable, for backfill, deep-mine chilled water and dewatering lines and other high-pressure piping applications. As engineers explore the use of high-pressure couplings, questions will undoubtedly arise about the joining method?s capabilities. This article will address the capabilities and specifications of high-pressure couplings, and compare flanged and grooved mechanical pipe joining in traditional as well as high-pressure underground mining applications.

Jan 1, 2011