Search Documents

By Richard G. Almes

Since the failure of a major coal refuse disposal embankment and impoundment in the Buffalo Creek watershed near Man, West Virginia in early 1972, there have been extensive changes in the design and construction requirements for coal refuse disposal facilities located throughout the United States. The primary emphasis has been on improving the safety of these facilities, particularly for impoundments which are capable of storing millions of gallons of process water and storm runoff. The Mine Safety and Health Administration (MSHA) of the U.S. Department of Labor (formerly the Mining Enforcement and Safety Administration, U.S. Department of interior) has been the lead federal agency in promulgating regulations pertaining to coal waste disposal. In 1974 and 1975, studies were undertaken by our firm under contract to the Mining Enforcement and Safety Administration to prepare a comprehensive engineering and design manual to be used by operators and engineers in the planning and design of coal refuse disposal facilities with the intent ion of avoiding any more Buffalo Creek failures. The resultant 800-page document addresses major subjects such as safety, environmental controls, and cost. Specific topics include characterization of coal refuse, classification of disposal facilities, project planning, geotechnical investigations, testing and design requirements, hydraulic and hydrologic design, environmental factors, operations, and monitoring, instrumentation, and maintenance.

Jan 1, 1980

By C. W. Schultz

The Alabama tar sands of the Hartselle Sandstone formation present a more difficult problem in primary extraction than do the Athabasca tar sands. In contrast to the Athabasca tar sands, the Alabama tar sands are "oil wetted" and the contained tar, or bitumen, is of much higher viscosity. A physical beneficiation scheme was developed in which clean sand from an external source was used as a scrubbing medium. High intensity scrubbing liberated the tars which are readily recovered by froth flotation. Locked cycle tests have shown that, after the use of an initial ration of clean sand, the system produced enough new clean sand to be self sustaining.

Jan 1, 1992

By Larry D. Patts

Section 317(e) of the Federal Coal Mine Health & Safety Act of 1969 directed the Secretary of the Interior to prepare standards under which all working places in a mine shall be illuminated by permissible' lighting while persons are working in such places. Section 317(e) further provides that such Working places shall be illuminated within 18 months after such standards are promulgated. In accordance with this section of the Act, there was published in the Federal Register for December 31,1970 a notice of proposed ru1emaking which prescribed the illumination to be provided in the working p1 aces of underground coal mines. In 1ight of written comments, suggestions, and objections to this proposed ru1emaking, the proposed standards were with-drawn and reproposed in the Federal Register for Wednesday, October 27, 1971. In light of further comments, suggestions, and objections, a public hearing was held on April 4, 1974 and standards were again reproposed and published in the Federal Register for April 1, 1976. Promulgation of the final lighting standards took place on October 1, 1976 which means that the underground coal mining industry must comply with face illumination requirements by April 1, 1978. As mentioned previously, the first proposed ru1emaking for illumination of underground coal mines was published in the Federal Register on October 27, 1971. In early 1972, Consolidation Coal Company (Consol) and the United States Bureau of Mines agreed to a cooperative study of underground face illumination; Conso1 felt that expertise in this field would become increasingly important. Conso1's initial efforts in illumination were aimed at investigati.ng practical lighting systems for underground face equipment. We were concerned with installing unobtrusive lights which provided sufficient face illumination for safety, but at the same time were readily maintainable, electrically reliable, and physically sheltered from damage.

Jan 1, 1977

By Shailendra Chawla, Ashok Jaiswal, Sonu

Side spalling/skin failure occurs due to the high-induced stress in underground structures. In such cases, rock bolting or other support systems are being used to control the skin failure or spalling of the pillar. The nature of these support systems is passive, which acts during the deformation. These support systems restrict the displacement considerably of the side/or roof surface of the excavation. Ultimately, it improves the stability of the structure because of the increment in residual strength of rock mass. It is noted that these passive support systems give very low confinement in the range of 0–0.015 MPa at the onset of failure. As the level of confinement will be very low and dependent with progress of failure, triaxial test was not found practically suitable. Thus, an alternative procedure of testing has been proposed. In the procedure, sides of sample have been restricted little bit by using adhesive tape. It provides the limited boundness on the lateral direction (LBLD) of rock specimen. The uniaxial compression strength (UCS) test has been performed on 30 numbers of cylindrical rock specimens using the servo-controlled stiff testing machine. Specifically, two rock types (medium-coarse–grained and coarse-grained rocks) were studied in terms of stress–strain behaviour so that a full residual strength envelope for each specimen was obtained. This study reveals that the residual strength of limited confined rock specimens has been significantly increased as compared to unconfined rock for both groups of rock types. The average residual strength of LBLD specimens of fine-grained rock and medium coarse-grained rock has been increased around 12 times, and five times as compared to unconfined rock, respectively. The average peak strength of LBLD rock specimens has been increased in the range of 30.5 to 48.6% for coarse-grained rock. The results of this study have been presented in terms of peak strength, residual strength and Young’s modulus of rock, and the post-peak failure behaviour of rock specimens was also critically analysed through a stress–strain curve.

Mar 21, 2024

By R. A. Seitz

This paper presents a framework for analyzing the theory and industrial practice of coal flotation and gives some examples of its use for understanding flotation phenomena and optimizing/controlling flotation circuit performance. It is based on extensive laboratory and in plant test work conducted over the past several years by researchers at MTU as well as an analysis of the literature. Previous researchers have usually considered either the surface chemistry or the kinetics of coal flotation behavior, only rarely have these factors been considered together. However, these factors must be considered together in order to gain a clear understanding of the theory underlying coal flotation such that its practical application can be optimized. Fortunately, this complex objective can be achieved by considering the recovery and rate of recovery of the different types of particles present in the feed to coal flotation circuits and the fundamental mechanisms responsible for these recovery phenomena. The influence of three major groups of variables must be considered: control variables (reagent additions, aeration rate, etc.); disturbance variables (feed pH, percent solids, etc.); and circuit design variables (number of cells, circuit arrangement, etc.). Each of these groups of variables affects process kinetics in a clearly understandable manner, which, once determined, is extremely useful in circuit design and optimization. This paper includes a discussion of the use of the proposed framework to explain the effects of some coal characteristics on flotation performance. In addition, an example of using this analysis to optimize the performance of a coal flotation circuit using frother and collector addition levels is included.

Jan 1, 1985

By T. P. Weldum, W. Conger

"The objective of the study conducted by the authors is to determine what media size(s) addition will maximize any given plant ball mill’s grinding efficiency (Fig. 1). The functional performance parameters “mill grinding rate through the size of interest,” and “cumulative mill grinding rates” from both plant and smallscale tests are applied to this task. A plant media sizing methodology, and industrial case studies, are provided.BackgroundA previous article (“Ball mill classification system optimization through functional performance modeling,” Nov. 17, McIvor et al., 2017, Mining Engineering) described circuit classification system efficiency (CSE), equal to the percentage of coarse (plus circuit P80 target size) material in the ball mill. It can be measured and then increased through pump and cyclone adjustments. By so transferring the application of ball mill power from fine (minus P80 product size) to coarse material, circuit efficiency is increased and overgrinding is decreased.The other factor that determines overall circuit efficiency is how well the power that is applied to the coarse material grinds it. This is affected by design and operating variables like the media sizing and mill percent solids. From circuit functional performance (McIvor et al., 1990):Circuit production rate of new fine material (t/h) = Power applied to coarse material (kW) x Mill grinding rate of coarse material (t/kWh) (1)The power applied to coarse material is the total mill power multiplied by the CSE. Therefore:Circuit production rate of new fine material (t/h) = Total mill power (kW) x CSE (%) x Mill grinding rate of coarse material (t/kWh) (2) Production rate, mill power and CSE can be measured during a plant circuit survey. The mill grinding rate of coarse material is then calculated. At the circuit target P80 size, this is the mill grinding rate (of coarse material) through the size of interest. The objective is to maximize this rate. The mill grinding efficiency can also be calculated by taking the ratio of the mill grinding rate over the material’s grindability as measured in the lab. Mill percent solids optimization has thusly been achieved (McIvor et al., 2000). For media sizing, maximizing the mill grinding rate on a given ore is equivalent to maximizing the mill grinding efficiency. Ores of different grindability will be part of the discussion."

Jan 11, 2018

By G. Pierson

Explanations for commodity price levels (or movements) commonly focus on the fundamentals of supply and demand, otherwise they are simply assigned to speculative activity. Comparisons of metal-price histories to monetary and other economic data support the argument that the supply of and demand for money are no less important in the determination of price than are the supply and demand of the commodity itself. That these relationships should exist is evident in the price identity and they are consistent with monetary theory. The patterns developed have limited usefulness as predictors, but their recognition is essential for the construction of price scenarios for planning purposes.

Jan 1, 1997

By Matthew T. Mowry

As the mining industry continues to hire young professionals to supplant the growing number of retirees, a well-developed engineering curriculum, coupled with practical, real-world training, can prepare mining engineering graduates to make meaningful contributions in the industry. Successful companies can be measured not only by their reserve base and annual production but also by their retention of mining engineering graduates with zero to five years of operational experience. My personal experience in the industry during the last five years has been varied and rewarding. The knowledge and experience I have gained have taught me valuable lessons that prepared me for my current role.

Nov 1, 2013

By Carl E. Bagge

It is easy for a coal spokesman to relate to the theme of this meeting--that the decade of the 1970's is pivotal for the mineral industries. For the coal operator, this period is crucial. The coal industry, according to most energy forecasters, must gear its production machinery to meet a sharp rise in the demand for coal--in this decade to sustain inevitable boosts in electricity output, and in the next to start supporting a big new domestic synthetic fuels industry that is already in the formative stage. The logic of that projection flows from a combination of hard circumstances--proved reserves of domestic fluid fuels are dwindling, the hope for bountiful and cheap nuclear power must be indefinitely deferred, and the threat of long-term fuel imports to the national interests is becoming starkly visible. Only coal, with its assets of abundance, security and versatility, offers the nation an adequate and immediate lift out of its current energy crisis. A hard-won expansion of coal production made the critical difference between local power load-shedding and major area blackouts in 1970, the year the energy crisis went public. Coal will have to play that same key role, not just through this pivotal decade but through the turn of the century. But the logic of fuel demand apparently does not always extend to supply. The coal industry has had a huge production job laid out for it by the energy statisticians, but up to now the energy policy-makers have not followed through with the aids and inducements that the coal operator urgently needs to do that job well and completely.

Jan 1, 1972

By Henry E. Swanson

In the early 1960's the Company, then named the United States Smelting Refining and Mining Company, was drilling the Continental ore body located near Fierro, New Mexico. Reserves of underground ore of sufficient quantity were indicated to build a mill. At the same time some ore from the Continental No. 1 mine was being milled at the Company's Bullfrog Mill, formerly a lead-zinc mill. The copper ore in comparison to the lead-zinc ores was very hard, abrasive, and heavy. These factors pointed out the possibility and attractiveness of autogenous grinding. While prior to this some study had been given to autogenous grinding, no large scale tests had been made. Such a program was carried out and from the pilot plant data the following was established: 1. Grinding of the ore by autogenous means could be accomplished. 2. This could be done in one stage; however, not at a satisfactory tonnage throughput rate. Thus, the use of a secondary unit has been employed. 3. Grinding in the secondary unit could be done by pebbles generated in the primary unit. This resulted in the scheme whereby the ore would be ground 100% autogenously. 4. Liberation of the copper minerals was excellent so that good recovery at a satisfactory concentrate grade would be obtainable.

Jan 1, 1976

By William M. Turner

Thermonics is a methodology of ground-water flow system analysis based upon the distribution of heat within the subsurface as influenced by moving ground water. Thermonics is based upon the Stallman Equation 1 (1) which describes the simultaneous transfer of heat through a porous medium which contains moving ground water. The Stallman Equation is:

Jan 1, 1980

By A. Patrick Ryan

To many people, the word cartel implies illegality. However, although it is illegal in the US, cartels are an effective and legal way to conduct business elsewhere in the world. But be-fore we continue, what is a cartel? The American Heritage Dictionary defines a cartel as "a combination of independent business organizations formed to regulate production, pricing, and marketing of goods by the members." However, that definition does not fit many of the "cartels" we are examining today. The International Tin Council is an organization of both consumer and producer nations--no individual companies are represented. The buffer stock is used by the ITC to provide protection for both producers and consumers, and has only been in effect since 1955. (Earlier tin producers groups date back to 1921 when the Federated Malaysia States and the Netherlands East Indies formed the first intergovernmental tin agreement, known as the Bandoeng Pool, which only lasted three years.) The International Bauxite Association only dates back to 1974 when seven nations--Australia, the Dominican Republic, Ghana, Guinea, Guyana, Haiti and Jamaica--agreed to three main objectives: 1) to promote the orderly and rational development of the bauxite industry; 2) to secure a fair and reasonable return on the raw material for the benefit of the nations' citizens; and 3) to safeguard the interests of member countries in relation to the international bauxite industry. 1 Again this organization is composed of nations, not separate firms. This generally follows the pattern that the oil producing countries (OPEC) chose since the nations' mineral product-ion is controlled and often owned by the state. However, the group I am going to discuss fits the more classic mode of a cartel. The informal lead-zinc producers' cartel can be dated as far back as to Roman times when Romans are said to have imposed a quota system on British lead production to safeguard their Spanish lead mines. Also, the lead-zinc producers group is composed only of individual companies, not do not include any lead-zinc consumers. Finally, the activities of the group are not open to public scrutiny, and details are only now available due to a leak in the Australian government. At this point, it is necessary to split the two metals since while many of the members of the cartels produce both lead and zinc they do have different histories and marketing arrangements.

Jan 1, 1978

By Chin Wei Yang

Linear programming (LP) has proven to be a most effective mechanism for modeling a vast array of practical problems, while the development of LP applications in engineering have been extensive enough to show its advantages and limitations. In this paper: we focus on the properties of the widely-wed linear programming transportation (LPT) model formulated and developed by Koopmans (1) . There have been many models of this type applied especially in the field of energy economics (2-7). Since most of these applications can be linked to the seminal work of Henderson (8), we stall present our discussions based on his work.

Jan 1, 1980

By F. Romero, L. Yacher, M. Orchard

Specific software tools for Statistical Multivariate Analysis combined with real time process data were applied to Concentrator Plant at Compañía Minera Doña Inés de Collahuasi SCM in Chile, basically to two Mill Lines, each one with one SAG mill (32’x15’8MW)and one Ball mill (22’x36’9.7MW). The main objective was to empower the operator actions using process patterns references instead of process variable set-points. Pattern clustering and the analysis of pattern deviations regarding normal or desired pattern, allows for improvements in process control and the further implementation of soft sensors for those variables not included in the initial model.

Jan 1, 2003

By J. Wesley Atkins

In considering the importance of lease management and administration, I have decided to approach the topic, Lease Default and Eviction: Action or Reaction, as a three phase presentation dealing with mineral lease administration and management, past, present and future. Though the title may border on the dramatic, it illustrates the real consequences of alternative approaches to property management viewed from my experience in the evaluation, development and implementation of a number of such systems and services in my current position as president of Talco Group Corporation. First, though, let's take a moment and set the stage by giving a few actual examples of why a pragmatic approach is needed in this particular area.

Jan 1, 1983

By Brendan Demich, MAHIYAR F. NASARWANJI, Alan G. Mayton

Nonfatal injuries from slips, trips, and falls (STF) that occur at surface mines can result from inadequate lighting. Mobile equipment operators are among the occupations associated with the nonfatal incidents reported to the U.S. Mine Safety and Health Administration (MSHA). In addition, getting on/off the equipment (ingress/egress) frequently adds to the highest proportion of nonfatal incidents. Accordingly, researchers at the Pittsburgh Mining Research Division (PMRD), National Institute for Occupational Safety and Health (NIOSH) conducted a field study to investigate lighting on haul trucks and wheel loaderswith regard to glare and illuminance levels recommended by the Illuminating Engineering Society (IES). The objective was to determine whether two light-emitting diode (LED) area luminaires—a Mr. Beams® (model MB390 Ultrabright) (area luminaire-1) and a NIOSH-developed Saturn (custom-designed for a mine roof bolter study) (area luminaire-2)—could complement a headlamp luminaire. Measured levels of visual tasks, with the headlamp alone and the area luminaires plus the headlamp, demonstrated that illuminance met or exceeded IES-recommended levels. Nevertheless, the area luminaires illuminated a much broader area, which is key to increasing hazard awareness. Discomfort and disability glare were lower with area luminaire-1 than with area luminaire-2. Differences in glare were more noticeable for newer models of haul trucks and loaders featuring updated ingress/egress system designs. This study demonstrates that commercially available luminaires, such as area luminaire-1, are capable of complementing headlamp lighting, and can thus improve a miner’s ability to detect and avoid STF hazards.

Jun 17, 2020

"INTRODUCTION In recent years, there has been increasing focus on environmental and social impacts of the extractive industries, climate change and resource scarcity. The concept of the circular economy aims to replaces the “take-make-dispose” economic model with one that eliminates waste of all kinds and is restorative by design. Such closed-loop systems implicitly aim to reduce the quantity of primary extracted materials entering the economy, thereby affecting supply and demand dynamics, hence mining industry economics. For the metals industry, the ability to engage in, or adapt to the circular economy can be heavily affected by industry structure and geographical factors. Eco-efficiency initiatives that reduce waste and environmental impact may help the mining and metals industry align with some of the goals of the circular economy. This paper focuses on base metals, and explores case studies in copper, lead and zinc. It analyzes primary and secondary metal production, and recycling. It examines company structures and how these affect engagement with the circular economy. CIRCULAR ECONOMY PRINCIPLES Ellen MacArthur Foundation (2012) describes the circular economy as “an industrial system that is restorative or regenerative by intention and design”, which “replaces the ‘end-of-life’ concept with restoration”, and “aims for the elimination of waste through the superior design of materials, products, systems, and, within this, business models”. The concept is systems focused. For materials such as metals, a series of loops are considered, including maintenance of devices, reuse, refurbishment and recycling. Potential methodologies to achieve circular economy outcomes include disassembly and reassembly of manufactured goods, leasing rather than buying major appliances, and converting to renewable energy sources. The circular economy is partially aligned with the principles of eco-efficiency, which relate to reducing the environmental impact per unit of a material produced. PRIMARY AND SECONDARY METAL PRODUCTION Base metals (copper, lead, zinc and nickel) are essential ingredients in modern economies and are key commodities produced by the global mining industry. Metal production can be categorized as primary or secondary. Primary metal comes from the processing, smelting and refining of metal content extracted from ores, while secondary production comes from metals recovered from recycled streams (e.g. recycled lead-acid batteries, copper wire scrap, etc.). Metals are stored in natural, anthropogenic in-use and anthropogenic waste stocks. An example of the stocks, flows and processes associated with global copper extraction and use is shown in Figure 1."

Jan 1, 2018

By T. W. Camm

One function of the U.S. Bureau of Mines is assessing potential economic impacts of federal land withdrawal policies. This often requires performing economic ana1ysls for an area with limited geologic information available. Input to the economic decision process relies heavily on estimates of mine and mill costs for the potential resources in the area being considered. A methodology for performing these cost estimates was needed to address this situation.

Jan 1, 1992

By W. Dan Hausel

Archean supracrustal rocks of the South Pass greenstone belt of western Wyoming have been an important source of gold and iron ore. Actual gold production statistics are incom- plete although gold production estimates for the South Pass- Atlantic City district range from a low of 2.0 Mg (70,000 oz) (Koschmann and Bergendal, 1968) to a high of 9.8 Mg (327,000 oz) (Hausel, 1980). From 1962 to 1983 iron ore was also mined from the greenstone belt and production totaled more than 91 Mt (90 million It). The supracrustal rocks of the South Pass greenstone belt occur in a tightly folded synform bounded by Late Archean granite and granodiorite. The youngest of the Archean successions has a reported Rb-Sr isochron age of 2.8 b.y. (Stuckess, et al., 1985). Metamorphism of the supracrustals increases towards the flanks of the belt and is amphibolite-grade enclosing a small island of greenschist facies rocks. The supracrustal sequence consists of metasedimentary and metaigneous rocks that are divisible into four mappable units. The metasediments include metagraywacke, quartzite, pelitic schist, banded iron formation, metaconglomerate, and graphitic schist. Metavolcanics include metabasalt, meta-andesite, and ultramafic schist. These supracrustals have been intruded by mafic sills and dikes and tonalitic stocks and dikes. Two granite plutons and associated pegmatites intrude the supracrustals in the western portion of the belt, and the supracrustals exhibit both fault and intrusive contacts with granitic batholiths along the western and eastern margins. The northeastern flank of the Archean belt is unconformably over- lain by Paleozoic sediments, and the southern portion of the belt is onlaped by Tertiary sediments.

Jan 1, 1990

By R. J. Pugh

The coagulation of dispersions of weakly magnetic oxide mineral ultrafines (such as natural hematite or chromite) in an external magnetic field can be described from inter-particle forces. Essentially, coagulation occurs when the short range London-van der Waals interactions and the long range magnetic forces outweigh the stabilizing electrical double layer repulsion. From the classical colloid chemistry theory, we have calculated the various components of the potential energy for different sized particles at a series of ionic strengths and magnetic field intensities. We have related this theoretical analysis to experimental studies where the magnetic field-induced coagulation of ultrafines of natural hematite and chromite in aqueous suspensions was investigated using a laboratory scale electromagnetic solenoid. The experimental results relate the coagulation process (as determined by magneto-sedimentation analysis) to the particle size, the slurry pH and the external magnetic field. In the magnetic fields, maximum coagulation occurred near the pH of zero point of charge (pHzpc) of the minerals (where the electrostatic double layer repulsion was reduced to a minimum) enabling the particles to enter the "primary minimum" energy sink. On the other hand, in cases where the electrostatic repulsion was not suppressed, then the long range magnetic forces enabled coagulation to occur in the "secondary minimum". This caused the formation of chains which appeared to be relatively stable during sedimentation.

Jan 1, 1993