Search Documents

By R. Zins

During the past few years, a completely new concept has been applied to the design of drives for operating at very low speeds. In this, the motor is supplied by a variable-frequency thyristor cyclo-converter. Today, frequency converters with practically unlimited power ratings can be constructed. The system frequency of 50 or 60 Hz is reduced to about 10 % of these values. This makes it possible to operate the synchronous motor, which has a correspondingly high number of poles, at the extremely low speed of the driven mill, i.e, without interposed gearing. The first motors of this type were built to drive ball mills in the cement industry, which are very similar to those employed for ore processing. Here, too, the tendency is to build units of ever increasing capacity. In the case of conventional drives with mechanical gearing, this involves correspondingly increasing difficulties. These difficulties have prompted various studies of the possibility of applying the new type of drive to ore mills as well, but a gearless drive has not yet been built for this application. However, gearless drives for ore mills will certainly materialize soon and it was therefore considered a logical step to report at the A.I.M.E. Conference on the experience gained with these drives in the cement industry, and on the present state of development.

Jan 1, 1973

By L. E. Mercando

The proposed Flambeau Mining Project is based on a high grade copper deposit located approximately one mile southwest of Ladysmith, Wisconsin. The project involves only the mining, crushing, and shipping of ore to facilities outside of Wisconsin for processing. The Wisconsin environmental regulations include provisions for identifying wetlands, the requirements for minimizing the disturbance of wetlands, and the need to establish new wet-lands to replace any wetlands which have to be disturbed.

Jan 1, 1991

By F. Soumis

We propose an advanced truck dispatching system which uses mathematical optimization approaches including integer programming, non-linear networks and the assignment problem. The system produces better operation control than existing algorithms. Furthermore, it provides planning tools for choosing equipment and finding an equilibrium between the quality and quantity of production.

Jan 1, 1986

By MAURICE SUNKPAL, Taghi Sherizadeh, ELAHEH TALEBI, PEDRAM ROGHANCHI

Excessive heat exposure is among the health and safety hazards for mine workers. The nature of the underground climate makes it a convenient avenue for heat generation and accumulation from several heat sources, including autocompression, equipment and heat from strata. This study investigates the effects of clothing insulation and acclimation on the thermal comfort of mine workers exposed to heat in underground working environments. Several clothing ensembles were considered to analyze the effect of the thermal resistance of clothing on the workers’ thermal comfort. To investigate the impact of clothing insulation, the thermal comfort limit of an underground miner was calculated in the form of maximum allowable exposure time for an eight-hour shift.

By M. Deniz Turan, HASAN NIZAMOGLU, MÜCEVHER TURAN, RAMAZAN ORHAN

Tailings, or flotation waste, formed during copper production may be considered in the class of valuable wastes because of the amount of copper they contain. With the decreasing grade values of copper ores, the utilization of wastes like tailings that carry certain amounts of copper as secondary sources has become a necessity in both the economic and environmental senses. This study was carried out with the aim of using ammonium derivatives for the recovery of copper from tailings waste produced during copper production and utilizing their complex formation characteristics. In the conditions of six hours of leaching at 30 °C in the presence of 22.5 percent ammonium hydroxide and 100 g/L ammonium persulfate, 91.47 percent of the copper was transferred into the solution, while iron was not transferred, indicating that copper can be selectively recovered from tailings.

By A. Hammons

Automated temporary roof support (ATRS) systems have been incorporated into roof bolters since the 1970's. During roof bolting, many injuries have occurred from large pieces of draw rock falling inby the ATRS beam and tipping back into the operator's area. Other injuries have occurred due to smaller, sharp rocks falling onto the operator's hand and arm during initiation of roof bolt drilling. These injuries are attributed to weak immediate roof, sometimes called roof skin failure. Even though ATRS systems support the roof and provide a measure of protection against roof skin failure, additional hazards sometimes do exist immediately inby and outby the supported roof. Design innovations such as the ATRS mounted rocker pad deflector systems have been designed to improve the roof bolter operator safety. This paper will inform the reader of the hazards, machine evolution through different design solutions, and the current state of the art in preventing roof skin failure injuries when roof bolting.

Jan 1, 2009

By David R. Hargis

Large-scale groundwater withdrawals are necessary to depressurize a confined aquifer system allowing the dry open-pit mining of the overlying phosphate ore. The extent of the existing and planned groundwater development led to the establishment by the State of North Carolina of Capacity Use Area No. l. Groundwater use in the Capacity Use Area is regulated by a permitting system. A two-dimensional finite-difference ground- water flow model was developed for North Carolina Phosphate Corporation. The aim of the model is to aid the Corporation in matters relating to permitting by serving as a predictive tool. The model can be used to project regional water level impacts resulting from various scenarios of depressurization pumping.

Jan 1, 1983

By K. Voltaire

As can be guessed from the subtitle, this paper will not be a geologist's one since neither of the authors is a professional geologist. This will be an attempt to present the various aspects of the legal, economic and geological setting that condition the exploration for mineral resources in Haiti. Before going any further, we are going to present a summary of our rather short mining history. One must first mention that Caribbean countries are latecomers to the mining business. If we go back to the colonial period (1500-1600's) there are net many traces of mining activity. The major exception to this is the recovery of alluvial gold in Hispaniola, Puerto-Rico and Cuba and also some sporadic copper mining in Hispaniola (notably in Haiti near the city of Gonaives and in some of the old mining districts in Santo-Domingo). These easily minable deposits were quickly exhausted and mining quite naturally came to an end as agriculture rose as the major economic activity. In the Haitian case, aside from very erratic mention during the 19th Century of the presence of some minerals (i.e. haematite, chalcopyrite) no serious geological work was undertaken. In the meantime, the peasants in the northern part were still looking for alluvial gold in some streams but this amounted to next to nothing. One has to come to the 1920's to find the first comprehensive geological survey. At the time, the country was under the military control of the United States. The American Government sent a team from the U.S.G.S. headed by the late W. Woodring to initiate a survey of the country. Given the lack of transportation, this was a tough task and Woodring and his associates did it magnificently. As a result of their efforts, they published a very thick piece of work of more than 600 pages. "The Geology of the Republic of Haiti" although it was published in 1924 is a classic and is a must for anyone interested in the geology of Haiti.

Jan 1, 1978

By Paul Soros

The Conneaut, Ohio, terminal of the Bessemer & Lake Erie Railroad was the first rail-to-ground-to-water coal terminal on the Great Lakes. Compared to the traditional method of holding coal in railroad cars at the ports for dumping their contents into vessels, it provided for: a. Immediate train turn-around independently of vessel arrivals. b. Winter storage of coal at the port, permitting year round shipment by the mines and year round operation of the railroad.

Jan 1, 1969

By M. Z. Rashad

The intersections of numerous joint sets at the surface of tunneling region of Abu-Tartour-Project in Egypt create blocks with irregular shape and size in the rock mass. Most of these blocks are not able to move into the free space of the tunnel. Few key blocks are in a position to move and as soon as they begin so, some restrained blocks will be liberated. The aim of this work is to find the (removable) key blocks for walls, floor, roof and corners of a portion of the tunnel under jointed surface rocks; and then determine the best tunnel direction.

Jan 1, 1991

By L. M. Pero

The paper summarizes aspects of the recent literature on mineral development in the Third World. The emphasis is on publications covering agreements between host governments and mining companies.

Jan 1, 1985

By Dominique Francois-Bongarcon

The rational and optimal determination of the design of a mining exploitation is a very intricate and difficult problem : the parameters are numerous, some technical, some economic or technico-economic which cannot be fully controlled; beside, deposits are estimated from very limited information and the choice criteria are not always quantitative, the economic context has to be anticipated by several years, and even the technological limits can change tomorrow. So, although very clever and performing numerical algorithms have been developed in recent years for open-pit design, we consider that this problem has not really been solved satisfactorily until now. The reasons are that people have concentrated their efforts on informatical algorithmical problems, and have assumed that the technical and economical data are well defined at the time of the study, which is generally not true. In particular, the mere fact of assigning dollar- values to blocks in order to maximize the total cash-flow is generally unrealistic because of the uncertainty of the data used. Consequently, the significance of the unique pit obtained as a result of these algorithms is questionable.

Jan 1, 1981

By S. S. Huyett

The opportunity to cooperate with the Mining Department of the Pennsylvania State University in their Student-Trainee Program is accepted by The New Jersey Zinc Company who believes that the participation in this type of a program will lead to a larger supply of high calibre engineers in mining. Trainees compete with other employees to earn the cost of their education while gaining practical experience in the mining industry. The practical experience is arranged to complement the technical education through a variety of work assignments. Job opportunities for the trainee are related to the work requirements of the Company and to the performance of the trainee. Management must consider and deal with a good many problems uncommon with regular, full 'time employees. For a number of reasons this program is recommended to other companies as a means to encourage outstanding young men who are interested in a career in the mineral industry to obtain a professiona1 education.

Jan 1, 1963

By William J. Miles, Raymond E. Blair

Introduction There has been much publicity of the boom and bust in oil and gas well drilling in the US, and many comments on oil and gas gluts. Despite this, the drilling industry remains the largest consumer of functional industrial minerals. The boom years of 1981 and 1982, compared with the bust year of 1983, show a sharp reduction in the consumption of industrial minerals-1981, 7.4Mt (8.2 million st); 1982, 6.3 Mt (7 million st); and 1983, 4.4 Mt (4.9 million st). Industrial mineral use rebounded in 1984 to 4.7 Mt (5.2 million st). This was the second highest year in history in terms of wells drilled and third highest in footage drilled. Table 1 shows the history of drilling activity and mineral consumption from 1971 to 1984. The uses of functional industrial minerals in oil and gas well drilling were detailed by Miles and Blair (ME, 1983, October, pp. 1397-1400). As an update, this article addresses only the changes that have occurred in the industry in the past two-and-a-half years. It will be directed to mineral use and new products introduced to the industry. Drilling practices A partial explanation of where wells are being drilled with lower quantities of minerals consumed is: • In the boom year of 1981, there was a proliferation of number of suppliers chasing the same business. This resulted in multiple sourcing, multiple warehousing, and a huge increase in inventory that became surplus in the following years. The bust year, 1983, caused a severe shakeout in the number of suppliers of minerals and associated drilling fluids. • In 1981 and 1982, the wild speculation in the oil and gas industry led to drilling of speculative deep gas wells. Oil wells were drilled on a wildcat basis - in areas of unproven productivity. • Presently, the oil and gas well drilling industry is very active. But drilling is directed toward proven areas of production and working over old wells for increased production. This means a large number of wells are being drilled with lower average foot-

Jan 11, 1985

By Joseph W. Mullan

The today status of air pollution control legislation and regulations can best be described as an exaggerated state of environmental limbo. The '70's began but one and one-half months ago yet it already has been very appropriately named "the decade of the environment." This certainly will be the decade for new legislation - new regulations and hopefully "Clean Air." Already Washington is faced with legislators playing "pollution politics" to the crowds. Students have redirected their efforts from Vietnam to the cleansing of the environment and everyone including the man on the street has become an environ¬mental expert. This is the decade we all face, but where are we today? Pollution is not a new problem. It has been with us for centuries and while much is left to be done, much has already been accomplished. I will try to make some comparisons of what I believe to be the good and bad points in the national air pollution control picture and hopefully will generate within each of you sufficient concern as to which comparisons are sound.

Jan 1, 1970

Lingering effects of the 1990 oil shock that included overbuilding and corporate and individual financial distress caused the Gross Domestic Product to fall slightly to $5.67 billion (US billion = l09). With 254 million people - 697,000 in mining and petroleum - the US has more than 100 million dwelling units and 190 million licensed motor vehicles. New private housing starts fell 15% to one million units. New car production fell 11 % to 5.4 million units. Truck and bus production fell 8% to 3.4 million units. The inflation rate was 3%, while the prime rate of interest was 8.5%. The Producer Price Index (1982 = 100) changed as follows: -fuels and related products and power down 1% to 8l, • metals and metal products down 2% to 120, • chemicals and allied products up 2% to 126, and • non-metallic mineral products up to 2% to 117. Energy Imports of crude and refined petroleum, costing $50 billion, fell 5% to 2.8 billion bbl. Domestic petroleum production rose 1% to 3.6 billion bbl. Petroleum supplied about 39% of US energy, natural gas 24% and coal 22%. The National Energy Strategy was announced in February 1991. Its purpose is to encourage domestic production of fossil fuels and nuclear and renewable energy and to stimulate efficiencies in use. Congress continued to debate the strategy and took no action. Coal production fell 3% to 902 Mt (994 million st). About 60% of that came from surface operations. Seventy-eight percent of the total was used to generate electricity and 3% was coked.

Jan 1, 1992

By J. D. Allen

The Concord Mine Coal Preparation Plant of United States Steel Corporation, located near Bessemer, Alabama, began operations in June, 1950. The basic cleaning circuit consisted of a Chance Cone for cleaning the 2-inch x 3/8-inch fraction and concentrating tables for cleaning the minus 3/8-inch coal fraction. Dewatering of the final product was accomplished with 35-mesh vibrating screens. However, because Concord coal is very friable (Figure 1), 85 per cent passing three mesh and 25 per cent passing 28 mesh, there was a considerable amount of fines passing through the dewatering screens. To recover these fines, the dewatering screen effluent was sent to two 70-foot diameter hydro-separators with the underflow returning to the dewatering screens and the overflow going to a 175-foot diameter thickener for water clarification, (Figure 2). As might be expected, there was a considerable amount of recirculation of the minus 35-mesh coal in this system. This degraded the coal and led to higher moistures. It also resulted in a fines bleed-off of plant water and thickener underflow to a fine-coal settling pond. In 1961, vacuum filters were installed to supplement the screens and to recover the fine coal lost in the bleed-off. The above system resulted in a product moisture of about 20 per cent. Further reduction to approximately 11 per cent was accomplished by drainage from railroad cars during transit to the coke plant. Control of the moisture at unloading was poor because of variations in operating levels and railroad car availability, but since the Concord coal constituted a smaller percentage of the coal previously used at the coke plant, the high moisture and fluctuations did not seriously hamper coking operations.

Jan 1, 1966

By A. J. S. Spearing, B. Forbes, T. Kostecki, A. Hyett

Improving upon the past understanding of the interaction between installed rock bolts, the immediate roof and sidewalls is vital for the implementation of sound support system design, as this has a direct impact on rock-related safety. This is the primary goal in rock-bolt-related research. The earliest research in this field concentrated on limited laboratory and in situ measurements accompanied by theoretical analyses, based on the Kirsch equations. This represented the initial insight into understanding relative ground movements and their impact on primary support. However, these studies were far from complete. More recently, major technological advances in computing power within the mining industry has changed the scope from theoretical analysis to computer simulation. Even with these advancements our understanding of rock bolts in situ and in the laboratory has not progressed, particularly concerning bending and shear. To measure the behavior of rock bolts, the widely accepted practice is to populate the bolts with an array of strain gauges. Historically, resistive foil strain gauges or long displacement sensors have been used. Additionally, all instrumented rock bolts have used only two diametrically opposed slots. Rock bolts instrumented with these methods have significant shortcomings, one of which is the inability to capture shear and bending. The shearing and bending of rock bolts are particularly common in tabular soft rock mining, such as coal mining. This paper discusses the use of three slotted rock bolts, cut diametrically 120º apart, and two new optical fiber technologies populated along the entire rock-bolt length.

Jan 1, 2015

By Ray E. Harris

New developments have occurred in Wyoming's industrial minerals industry since the 32nd Forum on the Geology of Industrial Minerals in Laramie, Wyoming in 1996. The soda ash trona and bentonite industries have experienced overall growth. Gypsum and limestone production have remained constant, but have the potential for dramatic growth. The mining of zeolite ceased in 1997. The struggling dimension stone industry has increased production, but development has lagged behind the schedule predicted in 1996. The construction of a container glass plant and associated production of glass raw materials, as predicted in 1996 and imminent in 1998, is now on hold due to unforeseen market factors. Increases in railroad and highway construction have, and will, greatly increase the production of construction aggregate for local uses. An iron carbide industry, not foreseen in 1996, is in the planning stages.

Jan 1, 2001

By Panshi Xie, Yan Chen, Shaogang Wu, Yang Hang

In order to realize the intelligent mining of coal seam with large dip Angle, this paper adopts the methods of large proportion variable Angle loading threedimensional physical simulation experiment, numerical simulation and field measurement with digital twin technology. The hydraulic support with large dip Angle and large mining height is used as the prototype to design the physical entity model of 1:5 hydraulic support, combined with modeling and graphics rendering technology. Angle, displacement and load sensors were selected and placed to realize the data channel between the lower machine and the upper computer of the digital twin system, so that the position and load data of the physical entity model and the twin model of the laboratory hydraulic support could be shared in real time. Moreover, the multi-dimensional dynamic and static load transfer law and the position evolution characteristics of the support and surrounding rock under different inclination angles were analyzed. The results show that: with the increase of the Angle of the working face, first, the initial support force required by the support decreases, and the damage degree of the roof increases; When the roof is soft, the lifting operation can avoid the instability of the support to a certain extent. Second, under the action of positive pressure, the load of the top beam under different angles is balanced; Under the backpushing action, the load in the upper inclined area of the shield beam increases gradually, while the load in the lower inclined area decreases gradually. Under the lateral push, the load changes periodically, and the load in each cycle is increased compared with that in the previous cycle. Third, the numerical simulation analysis shows that the load on the lower bracket is less than that on the upper bracket, and the load on the bottom of all the columns is greater than that on the middle and upper brackets. In order to reduce the impact of the columns on the bottom plate or the base, it is necessary to improve the anti-subsidence ability of the base. Finally, according to the research results, the improvement and optimization measures of the support are put forward, and the field test shows that these measures effectively solve the problems of sinking, sliding and tipping of the support in the working face with large inclination Angle, and obtain good application results.

Feb 1, 2024