Search Documents

By Thomas Novak, Sampurna Arya

Controlling dust generation and keeping it below permissible limits to meet federal dust standards at the working face of a room-and-pillar coal mine is a challenge for a mine operator. With the recent changes in federal dust regulations requiring lower worker exposure, maintaining compliance has become increasingly difficult. The current most effective practice of dust control at a continuous miner face in an underground mine is the use of a flooded-bed scrubber. A study carried out by the U.S National Institute for Occupational Safety and Health (NIOSH) indicated that a flooded-bed scrubber could achieve cleaning efficiencies between 58 and 90 percent. But the operation of such a system is maintenance intensive. The flooded-bed scrubber screen becomes clogged with dust particles and requires frequent cleaning to maintain performance. However, the dust control issue is not solely a mining-industry problem. Other industries face similar issues. The University of Kentucky collaborated with Toyota Motor Manufacturing on the development of a novel wet scrubber, called the vortecone scrubber, for capturing over-sprayed paint particles in automotive paint booths. The vortecone scrubber achieved a cleaning efficiency of 99 percent and required minimal maintenance. This study aims to assess the ability of this vortecone scrubber to capture respirable dust in an underground coal mine. The paper presents the results of computational fluid dynamics (CFD) modeling of this vortecone scrubber. It discusses the effects of air quantity and dust particle size on the performance of the scrubber. 

By Frederik P. Agterberg

Mineral exploration consists of the acquisition of data and their interpretation to ascertain the presence or absence of uncertain events. In general, the amount of uncertainty decreases during exploration when targets become increasingly well defined. Decisions on further exploration and whether or not mining should be commenced are based on new information using both objective facts and subjective reasoning. Computers play an important role during all stages of exploration. Three recent books (References 1-3) on decision-making in exploration and mineral-resources evaluation provide additional background supplementing the papers in this volume and articles in scientific journals or other conference proceedings (e.g., References 4 and 5) dealing with the subject. Other new developments to be considered are that microcomputers are becoming increasingly important in the earth sciences (Reference 6), and so are applications of artificial intelligence (Reference 7). Microcomputer- based technology allows rapid communication between field parties and main office. Expert systems are becoming increasingly sophisticated aids for mineral exploration an can now contain objective rules based on statistical theory (Reference 8).

Jan 1, 1989

By L. R. Berry

The successful selection of a slurry pump depends on the accuracy and completeness of the information provided for the application. Inaccurate or incomplete information can result in incorrect pump selection and / or operational problems. Some information is more critical to the selection process than other information. A full description of the slurry (liquid -solid mixture) including the particle size distribution and maximum concentration, the flow, head and NPSH requirements are most important for successful slurry pump selection and operation. Common problems resulting from improper slurry pump selection will be discussed to illustrate the need for correct selection requirements.

Jan 1, 1996

By E.C. Jong

Resumen ¦ Un sistema de comunicaciones “a través del suelo” (TTE) comercial y disponible fue evaluado en una mina de carbón subterránea en la zona Este del Estado de Kentucky. Este estudio de campo fue realizado como parte de una evaluación multisitio mayor de sistemas TTE disponibles. La mina detallada en este estudio se encontraba paralizada al momento de la evaluación, lo que proporcionó la representación más cercana a la realidad del medio ambiente en una mina luego de una operación de cierre. Para este estudio se probaron las comunicaciones superficie a subterráneo y subterráneo a superficie. El despliegue estándar del sistema TTE usando los procedimientos recomendados por el fabricante logró obtener comunicaciones claras y nítidas entre el socavón y la superficie. Otras disposiciones de las unidades arrojaron resultados mixtos. Existen planes para examinar más los fenómenos observados en esta mina.

Apr 1, 2016

By Hiroyuki Abé

This paper is a review of research and development on geothermal energy extraction in Japan especially on hydraulic fracturing. First recent geothermal developments in Japan are outlined in Part I. An increase in the production rate of geothermal wells may be highly dependent on the geothermal well stimulation technology based on hydraulic fracturing. The hydraulic fracturing technique must be developed also for geothermal energy to be extracted from hot, dry rock masses. In Part II, the research on hydraulic fracturing and field application are reviewed.

Jan 1, 1982

By Dragomir Gospodinov, Savka Dineva

A surprisingly large mining-induced seismic event occurred in the LKAB Kiirunavaara Mine (Sweden) on 18 May, 2020 at 03:11 (local time). The estimated moment magnitude was 4.2. The event caused extensive damage in a large section of the mine. The production in the area is not yet resumed, even by the beginning of 2022 (~20 months after the event). The Kiirunavaara Mine has one of the world’s largest underground seismic systems with approximately 253 geophones. The in-mine records of the event showed a very complex character with a several sub-events. The event was also well recorded by seismic stations out to over 9,000 km distance. Data from the underground and regional seismic systems were analysed to define and compare basic source parameters such as hypocenter location, seismic moment, as well as the seismic moment tensor. The data from the in-mine seismic system was used to study the development of the seismic process and to define elementary seismic sub-sources together with the official hypocenter location.

Apr 26, 2022

By Guoqing Li, Hao Wang, Nailian Hu, Victor Tenorio, Jie Hou

This paper presents an algorithm for optimizing the scheduling of trackless equipment in underground mines. With the shortest working interval and maximum productivity as goals, a genetic algorithm (GA) is used to solve the problem, and obtain the optimal working sequence with the most suitable equipment configuration possible. The input for the proposed method is the number of units and capacity of trackless equipment, the production process, ore amount in stopes, and the distance between stopes. The algorithmis verified using four setups of 5 stopes with 5 cycles, 5 stopes with 15 cycles, 10 stopes with 10 cycles, and 10 stopes with 30 cycles. The solution time of the algorithmis no more than 20 min, which is acceptable for practical applications. The results show that the setup of 10 stopes with 30 cycles is closer to the actual production of the mines, and the optimization model can effectively improve the operation efficiency. In this scenario, the robustness of the optimization is tested by simulating equipment failure events. Under the condition of 8% failure rate, the operation time is extended over 3.21–14.56% than expected, which represents strong robustness. The algorithm can quickly provide a feasible and effective solution for the production scheduling decision of trackless equipment in underground mines.

Aug 12, 2020

By H. Verakis

A fire in a coal mine conveyor belt entry represent a major safety and health risk to miners. Fighting belt entry fires can be a commanding effort. If there is a failure of one aspect in the fire fighting needs such as a dissimilar hose-valve connection, then it can result in the inability to extinguish a fire. Fire incident data compiled over nearly 30 years for underground coal mines shows that fires in belt entries account for 15-20 percent of the total number of fires. Fires in the belt entries of coal mines have resulted in injuries and fatalities. New regulations have been promulgated that require an unplanned fire not extinguished within 10 minutes of discovery to be reported to the Mine Safety and Health Administration (MSHA). A fire that is not extinguished within several minutes may take hours or days to extinguish or may require sealing a section or the mine in some cases. The current fire protection regulations in the U.S. Code of Federal Regulations (CFR), Title 30, Part 75 are designed to prevent or control the fire hazards present in a belt entry. These requirements and other factors affecting belt entry fires are discussed, including fire detection and warning, fire suppression devices, type and location of fire fighting equipment, waterlines, and cleanup and removal of combustible materials. The fire suppression systems used to extinguish/control a belt fire and the effect of ventilation on the propagation of conveyor belt fires are also discussed.

Jan 1, 2009

By T. J. Batchler

"INTRODUCTION A variety of standing supports are being applied in underground coal mining operations to assist in providing stable mine entries. Standing support performance requirements depend on the nature of the ground deformation behavior, and therefore require a good understanding of the interaction between the support and ground to achieve an optimum roof support system. Mining operations often employ standing support strategies that are unique to their mine. A support system that functions successfully in one situation could fail in another situation. It is important that the design and installation of the standing support systems provide the highest probability of preventing roof falls. Considerable research and development has been conducted by support manufacturers to develop standing support technologies for the mining industry. The National Institute for Occupational Safety and Health (NIOSH) researchers, with the cooperation of various support manufacturers, have developed a testing protocol that evaluates performance characteristics of these standing support systems.. Using this protocol, each of these support systems has gone through rigorous safety performance testing under controlled loading conditions in NIOSH’s Mine Roof Simulator (MRS). It is important to understand the unique performance characteristics of each type of standing support. This information allows mine operators to determine if the support system is compatible with the conditions in the mine and to compare each support system and determine if that support will provide equivalent or improved support capability. This paper provides a comprehensive summary of support performance to facilitate this objective. SUPPORT DESIGN CRITERIA AND THE GROUND REACTION CURVE Standing roof support systems are designed to prevent unplanned roof falls. The selection of the standing support is based on the interaction of the support with the surrounding rock mass, and its function is to assist the primary support system in maintaining the integrity of the immediate roof. The standing support works to control the immediate roof structure by resisting deformation that contribute to delamination of the bedded layers and displacements that lead to separation of the bolted zone from stable roof structures above the bolted horizon (Barczak, 2005). Standing supports should be installed early enough and develop sufficient capacity to bring deformation of the ground into equilibrium before a critical deformation is reached that leads to a detached block condition, at which point the standing support will be required to carry the entire dead weight of the detached rock mass to prevent a roof fall from occurring (Mucho, 1999). The ground reaction curve (GRC) can be used to assist in determining the compatibility and design requirements for a support system. It is important to understand the significance of the ground reaction relative to the support design requirements. The ultimate objective is to match the support behavior to the ground response and create equilibrium (stability) of the rock mass. This equilibrium is accomplished when the support loading intersects the ground reaction curve (Figure 1). Essentially, the ground reaction concept implies that the convergence in the mine entry is controlled by the magnitude of the support resistance. However, as a passive support, the standing support develops its loading through convergence. As such, the support needs to maintain its load capacity through the associated deformation of the ground and resulting entry convergence until the equilibrium condition is reached. This requirement causes factors such as the support stiffness, peak capacity, yielding characteristics, and stability to be fundamental to proper support design and application. NIOSH contributes to providing this understanding through full-scale performance testing of support products in the Mine Roof Simulator."

Jan 1, 2017

By Severn P. Brown

Cement plants in the central Hudson River valley utilize limestones of the Helder-bergian Series of the Lower Devonian. Chiefly calcilutites, calcarenites, and cherty calcisiltites, these rocks represent progressively deeper environments, from lagoonal to neritic, with scattered reef deposits. Stratigraphic continuity is marked, and a layer-by- layer analysis shows strikingly constant chemical compositions. The structural picture varies from flat-lying and relatively unfaulted beds on the northwest, through gently folded and faulted beds on the north, to complex overturned beds with closely spaced imbricate faults on the south. Operating techniques are simpler in the north, where grade control is effected chiefly by the initial layout of the faces. In the south, grade control requires flexibility and frequent adjustment of faces or scheduling. A system of quarrying along strike has been developed, grade being computed from a cumulative foot-per cent graph of the critical oxides in each mappable layer. Balancing shovel production among the many faces is simplified by comparing production requirement ratios with ratios of the various types of rock in each face. Drilling and blasting limits are geologically controlled if warranted, or large blasts embracing several rock types are shot and the resulting pile of broken rock is staked along shovel limits.

Jan 1, 1966

By Omar A. Muhtadi

Brohm Mining Corporation, in conjunction with Geobiotics, Inc. has nearly completed a pilot heap biooxidation test on sulfidic ore from the Gilt Edge Mine near Rapid City, South Dakota. Some results from the pilot testing have shown the correlation between the extent of biooxidation and the increase in cyanide gold recovery seen in the laboratory. Bench scale testing showed approximately a 1: 1 correspondence between percent biooxidation and percentage increase in gold recovery. The economics of large scale biooxidation were also evaluated in terms of increased gold recovery versus the time and cost of biooxidation. In the pilot test, the rate of biooxidation became limited by the acid water neutralization system. Later in the test, measures were taken to overcome this problem. Results from bench scale column bioleach testing showed that the Gilt Edge sulfide ore is quite amenable to biooxidation with a substantial increase in gold recovery with just partial biooxidation. Direct cyanide gold recovery of 51 % on ore crushed to -3/8" was enhanced to 82-85% after oxidation of37% of the sulfide as measured by iron. Laboratory experiments also showed that the slow rate of biooxidation of this ore could be accelerated by removal of metal sulfate build up from the leach liquor. The combination of these normally non-toxic metals became inhibitory to biooxidation if not removed by the neutralization circuit.

Jan 1, 1995

By Jack G. Quade

During the summer and fall of 1973 a series of Skylab and high-altitude aircraft overflights provided excellent hard-copy photographs of the Great Basin. These photographs, with a wide range of ground resolution were used by the NASA Project of the University of Nevada, Reno, to conduct specific geologic studies. The principal objectives of these studies were to: select individual areas covered by Skylab photography for detailed studies, develop mapping techniques using varied film-filter products with a wide range of ground resolution, compare the results of the mapping techniques to existing geologic maps at comparable scales, verify the results wherever possible by direct field observations. These studies were conducted by Jack Quade and Dennis Trexler and by graduates and undergraduates of the Reno campus under a contract with the Manned Spacecraft Center Houston, Texas.

Jan 1, 1976

"A commercially available through-the-earth (TTE) communications system was evaluated at an underground coal mine in eastern Kentucky. This field study was conducted as part of a larger multisite evaluation of available TTE systems. The mine detailed in this paper was idled at the time of the study, which provided the nearest practical representation of a postevent mine shutdown environment. For this study, surface-to-underground and undergroundto- surface communications were tested. Standard deployments of the TTE system using the manufacturer’s recommended procedures were able to achieve clear communications between underground and surface locations. Other arrangements of the units yielded mixed results. Future experimentation is planned to further examine the phenomena observed at this mine IntroductionThe ability to establish effective communication between surface and underground personnel after a mine event is essential for both evacuation and rescue efforts. Current wireless underground communication technologies are reliant on intermediary physical infrastructure, such as antennas and repeaters, to enable underground communications. As such, communications are easily disabled during a mine event because of the inherent vulnerabilities to physical damage (Damiano, 2012; National Academy of Engineers, 1970; Yenchek et al., 2011). A true emergency communications system would function regardless of a mine’s physical state. Through-the-earth (TTE) wireless communication technology only requires the use of a single transmitter and a single receiver to achieve point-to-point communication through solid strata. With this capability, TTE systems have the potential to serve as a true emergency communications platform."

Apr 1, 2016

By Thomas Hard

A description is given of a new facility processing blast furnace slag into a high quality cementitious material to be used as an ingredient in concrete for general construction purposes. A brief history of the process is given, followed by a detailed discussion of the water granulation system and the methods used to transport and dewater the granulate. Environmental advantages of handling slag away from the blast furnace by water granulation are included.

Jan 1, 1983

By A. R. Bell

Rio Algom Limited are currently undergoing a major expansion of their mining operations in the Elliot Lake area. To date this has involved the increase of output at the Quirke Mine from 4080 to 6350 tonnes per mill day (4500 to 7000 tons), the rehabilitation of the Panel Mine to produce at the rate of 2990 tonnes per mill day (3300 tons) by 1980, and the rehabilitation of the Stanleigh Mine to produce 4540 tonnes per mill day (5000 tons) by 1984. In addition, the planning for the rehabilitation of the Milliken Mine to produce 4990 tonnes per mill day (5500 tons) is now underway. This major expansion is taking place at a time of increasing awareness of occupational health matters and has involved very high capital expenditures and detailed planning related to the ventilation system to endeavour the provision of an acceptable environment. The paper discusses the ventilation systems, established and proposed, and relates them to historical and current data on mine air contaminants.

Jan 1, 1980

By H. Kimura

A new technology for ironmaking based on direct gaseous reduction of iron ore concentrate is under development. The process is based on the flash reduction of the concentrate particles in a gaseous reducing agent, such as hydrogen, natural gas, a reducing gas generated by partial combustion of coal, or a combination thereof. This technology is expected to drastically lower CO2 emission and reduce energy consumption by about 38% of the blast furnace requirements. The energy savings are possible largely due to the elimination of pelletization and cokemaking. Process design and simulation using hydrogen as the reductant for iron ore concentrate have been performed. A process flow sheet composed of a flash reactor, heat recovery system, water removal system for purifying recycled hydrogen, and all connecting streams was evaluated using the METSIM software. Ironmaking using two reactors was also designed and simulated, which could reduce the total required amount of hydrogen although it would increase the complexity of the flow sheet and operation.

Jan 1, 2010

By Hal McVey

The logic and importance of marketing in the industrial minerals industry is generally recognized by those of us intimately involved in this industry. The illogical instances where marketing is ignored in evaluating projects or poorly implemented in operations are also well known. The interplay between these two extremes is interesting territory and is explored commencing with a logical progression of a metal mine that became an industrial minerals mine and ending with the most illogical and failure-prone decision common to the minerals industry today. This paper will demonstrate how: 1. A logical progression of marketing expertise can result in previously unseen benefits to a minerals venture. 2. Logic can turn to illogic due to market conditions and price fluctuations. 3. How operations can turn marketing logic into illogical results. 4. Short term "logic" is often illogical.

Jan 1, 1981

By Ralph T. Buscarello

For practical purposes, the terms "natural frequency," "resonance" and "critical speed" are synonymous. A part passing though its "critical" or "critical speed" may also be said to be "resonant" or "resonating." The vibrations of a precisely balanced part can be magnified by the structure in which it is assembled. Anyone who has driven an automobile knows that it will vibrate more at a certain speed than at others. According to the formula for centrifugal force, vibration should increase steadily with a rise in rpm. What happens instead is that the vibration not only in- creases with r m. but suddenly rises at a much higher rate through the critical speed, and then apparently smooths out as the rpm passes beyond it. To visualize what happens, consider a simple flat spring with a weight mounted at one end. When the spring is deflected by pulling down on the weight and then letting it go, the spring will oscillate, and the spring-and-weight system will vibrate at its natural frequency. If the timing or direction bf the impulses imparted to the spring did not coincide with its natural frequency, the result would be an irregular vibration that would not build up. If, on the other hand, the timing and direction of the impulses did coincide with the spring's natural frequency, the result would be a larger and larger amplitude. If the impulses were continued indefinitely, the amplitude of the spring's vibrations would go on rising [while its frequency stayed the same] until the spring broke or the amplitude of the vibrations reached an equilibrium [because frictional or other forces would tend to damp it]. Resonance magnifies the amplitude of vibrations in a relatively undamped system between 100 to 200 times over that of nonresonant vibrations. Frictional or viscous damping often reduces the magnification [from 10 to 20 times], but even with this reduction the amplitude would still be large enough to cause excessive wear, and sometimes even fractures. For example, a blower might show only 0.001 in. of vibration on the manufacturer's test stand. Installed, the blower could pass into its critical speed [the speed at which the frequency of the vibrations caused by the rotor coincides with the supporting structure's natural frequency], and the 0.001 in. of vibration could be resonated to 0.010 in., or as much as 0.020 in. The cure for such a condition would not be to lower the vibration of the blower by further balancing or better alignment but to separate the two frequencies by at least 20 to 30%.

Jan 1, 1970

By Fred L. Myers

The use of finite element programs for evaluating large grinding mill shells is becoming increasingly popular. However, large scale, detailed analysis can become a burdensome task when one is required to manually prepare the necessary data to be entered into the program, while evaluating the voluminous results is even more devastating. Although available computerized finite element analyses can reduce computation time from years to months or even weeks, additional pre and post processors can reduce the time for data preparation and result evaluation to hours, while simultaneously reducing the probability of human error. Examples of the uses of these processors are presented as well as typical modeling techniques.

Jan 1, 1979

By K. C. Liddell

Chemical processing research made notable advances during 1986. This overview is necessarily brief. It is intended, though, to give the flavor of selected areas where recent activity has been high. At the 1986 Annual Meeting of The Metallurgical Society, a symposium was held on hydrometallurgical reactor design and kinetics. R. G. Bautista, R. J. Wesely, and G. W. Warren edited the resultant proceedings volume. This is the first available volume on this subject. It includes 26 papers on fundamental kinetic studies, modeling of reaction kinetics and reactor performance, and pilot and production-scale operations. Metals discussed include silver, gold, platinum, titanium, cobalt, nickel, zinc, copper, manganese, and iron. Agitated tanks, heaps, dumps, pachucas, pressure auto-claves, electrolytic reactors, liquid membranes, and fluidized beds are among the reactor types covered. An international symposium dealt with iron control in hydrometallurgy. It was sponsored by the Metallurgical Society of CIM, the Institution of Mining and Metallurgy, The Metallurgical Society of AIME, and Gesellschaft Deutscher Metallhutten and Bergleute. J. E. Dutrizac and A. J. Monhemius edited a proceedings volume containing 41 papers. These covered many areas of process chemistry, solvent extraction, precipitation, treatment of pickle liquors, impurities, residues and the environment, and process selection. Precious metals Concerning precious metals processing, the US Bureau of Mines IC 9059 is noteworthy. It includes papers presented at a USBM briefing at the Western Mining Conference in Denver. Topics covered included ion exchange, staged heap-leaching direct-electrowinning, and mercury precipitation during cyanide leaching of gold ores. Also dealt with were carbonaceous gold ores, carbon adsorption and desorption, heap leaching, the carbon-in-pulp process, and precious metals recovery from electronic scrap and solder. R. C. Sandberg and J. L. Huiatt (Journal of Metals, June 1986, and USBM RI 9022) developed a method to recover silver, gold, and lead from a complex sulfide using ferric chloride, thiourea, and brine-leach solutions. Gallium Gallium recovery was also a subject of considerable interest. Much information on this topic is proprietary. But two papers described solvent extraction of gallium. V. P. Judin and R. G. Bautista (Metallurgical Transactions B, 1986) developed an equilibrium model to separate gallium chloride from aluminum chloride. Tributyl phosphate was the extractant studied. T. Sato and H. Oishi (Hydrometallurgy, 16, 1986) investigated gallium extraction from sodium hydroxide by using Kelex 100. Data were given on the equilibrium distribution and the extraction kinetics. Galena Interest continues in recovering lead by hydrometallurgical processing of galena. J. E. Dutrizac; S. H. Kim, H. Henein, and G. W. Warren; and M. C. Fuerstenau et al. (Metallurgical Transactions B, 1986) all investigated leaching of PbS by ferric chloride. Dutrizac reported parabolic kinetics and reaction control by outward diffusion of lead through a porous layer of elemental sulfur. Kim, Henein, and Warren, however, reported that two leaching reactions occur. A nonoxidative reaction produces H2S and there is an oxidative leaching by ferric ion. Acid dissolution was found to predominate when the acid activity to ferric activity ratio is high. Surface chemical reaction was reported to be controlling. Fuerstenau et al. also reported that mass transfer through the sulfur layer is rate determining. But they believe that the species transferred are chloro complexes of ferric ion. In other work on lead, A. Y. Lee, A. M. Wethington, and E. R. Cole, Jr. of the USBM described an environmentally acceptable hydrometallurgical alternative to the smelting of lead concentrates (RI 9055). Uranium In spite of depressed prices, much work has been reported on uranium processing. R. G. L. McCready, D. Wadden, and A. March-bank (Hydrometallurgy 17, 1986) described the nutrient needs for in-place leaching by T. ferrooxidans. They reported the optimal conditions for uranium solubilization. L. E. Eary, H. L. Barnes, and L. M. Cathles (Metallurgical Transactions B, 1986) carried out an experimental and modeling study of uraninite dissolution. They concluded that ferric ion preferentially leaches uraninite in pyritic ores. Hydrogen peroxide was found to be less selective. A. Vuorinen, P. Hiltunen, and O. H. Tuovinen (Hydrometallurgy 15, 1986) studied redox and precipitation reactions of iron and uranium in leach liquors. P. T. Chiang (Hydrometallurgy 17, 1986) reported on the effect of uranium loading in the DEPA-TOPO process to separate uranium and iron from wet-process phosphoric acid. F. J. Hurst (Hydrometallurgy 16, 1986) conducted a fundamental study of the separation of uranium from phosphoric acid by DEPA and TOPO. D. E. Chia and W. C. Cooper (Hydrometallurgy 16, 1986) reported on bench and pilot scale work to recover uranium by the HIMIX process. They reported that the acid consumption to produce an eluate suitable for yellowcake

Jan 5, 1987