Search Documents

"Iron ore is the source of primary iron for the world’s iron and steel industries. Its production can be reported as crude ore, usable ore or iron content of ore. Historically, the U.S. Geological Survey (USGS) used reported crude ore production from China in tabulations of world iron ore production while other countries have typically reported their production in terms of usable iron ore. When China’s crude ore production was tabulated with usable ore production from other countries, world iron ore production totals have been overestimated by 10 percent to a high of content and may include products such as concentrates, direct-shipping ore, pellets, and sinter.• Iron content, also referred to as metal content or grade, denotes the amount of elemental iron in the crude or usable ore.BackgroundIron ores consumed in the steel industry typically require an iron content greater than 58 percent before being considered commercially usable. Iron ores that are not commercially usable must undergo beneficiation to raise the iron content. Approximately 98 percent of the world’s usable iron ore production is consumed in blast furnaces to make pig iron, which is further processed to make steel.High-grade iron ore mines can supply usable iron ore, known as direct-shipping ore, to blast furnaces, with minimal physical processing and no beneficiation. With direct-shipping ore, the reported production for crude ore and usable ore are the same. Ore from low-grade deposits must undergo beneficiation to increase the iron content before it can be used by the steel industry. In this instance, the mined material is called crude ore and post-beneficiation concentrates are called usable ore; the amount produced will be less than the crude ore amount. With the notable exceptions of countries such as Australia and Brazil, most of the world’s iron ore deposits are low-grade and require beneficiation."

Feb 1, 2017

By J. C. C. C. Menezes, R. A. S. Silva, A. V. Colling, I. A. H. Scheneider

"Coagulants rich in ferric sulfate can be obtained from pyrite-containing coal tailings using a biohydrometallurgical process. The aim of this study is to evaluate the relationship between quantity of pyrite and rate of oxidation, with regard to the consequent production of ferric sulfate for potential use as a coagulant for water and wastewater treatment. Leaching experiments were carried out on the laboratory scale on four coal tailings with different concentrations of pyrite. Characterization of the coal tailings was conducted for the following parameters: total sulfur, pyritic sulfur, sulfate sulfur, organic sulfur, and elemental analysis of CHN (carbon, hydrogen, nitrogen). The samples were also subjected to X-ray diffraction analysis to assess their mineral compositions. The leaching experiments were accomplished using a laboratory column constructed as a packed bed reactor with a sprinkling system in a closed circuit. After four weeks of leaching, the liquor was filtered and evaporated to an iron concentration of about 12 percent w/w, which is typical of the ferric sulfate coagulants commercialized in Brazil. IntroductionCoagulants used for the treatment of water and wastewater are predominantly inorganic salts of ferric iron and aluminum. Aluminum salts, including aluminum sulfate and aluminum chloride, and prehydrolyzed metal-ion reagents, such as polyaluminum sulfate (PAS) and polyaluminum chloride (PAC), are the coagulants most widely used for water treatment (Bratby, 1980; Tchobanoglous et al., 2003; Buzin et al., 2014).However, the presence of residual amounts of aluminum in drinking water has been controversially implicated in neurological diseases (Association of California Water Agencies, 2000; Becaria et al., 2006; Campbell, Hamai and Bondy, 2001; Rondeau et al., 2000; Walton, 2006). A possible alternative is to use iron-based coagulants, such as ferric chloride, ferric sulfate or polyferric sulfate, instead of the aluminum salts (Jiang, Graham and Harward, 1996; Jiang and Graham, 1998). Iron-based coagulants are commonly produced by the acid dissolution of iron scraps or iron ore (Tchobanoglous et al., 2003).Recent studies have shown that it is possible to produce ferric sulfate coagulants from the pyrite present in coal tailings through a biohydrometallurgical process (Colling et al., 2011). The main advantage of this process is that it does not require acid addition, which can be favorable in terms of production costs. Acidophilic bacteria, such as Acidithiobacillus ferrooxidans, can increase the rate of pyrite oxidation and dissolution by several times (Kontopoulos, 1998; Brett and Jillian, 2003; Johnson and Hallberg 2003). They can be highly significant in the bioprocessing of coal tailings for the production of ferric coagulants, as their action favors the acidification of the medium and iron leach (Colling et al., 2011)"

Jan 1, 2016

Sedimentation is used to clarify process effluents or to thicken process slurries. The sedimentation cycle of a suspension is presented as a settling curve. This curve is simply a plot of the height of the interface between the settled suspension and clear liquor versus time. Figure 1 shows a series of graduate cylinders which contain a suspension at various stages in its settling cycle. Cylinder 1 shows the suspension completely mixed at time zero. After a brief period of time (see cylinder 2), the suspension is observed to settle from its initial height Ho to height H1, leaving behind a volume of clear (or turbid) liquor, called the supernatant. The interface between the supernatant and suspension is termed the mud line. It is also possible to distinguish at the bottom of the cylinder a layer of sludge representing solids which have settled from the suspension. The interface between it and the suspension is called the sludge line. The sludge line moves upward in the cylinder.

Jan 1, 1992

By V 9. 0 / 300 dpi

In the time period from the early 1980's to the present, longwall roof support technology has evolved tremendously. Chock supports and caliper shields were replaced by 2-leg or 4-leg lemniscate shields. The lemniscate linkage for which the support is named offers numerous advantages to the sup-port both as a fabricated structure and to its performance in the mining application. The hydraulic system, which is the dynamic element of the roof support, was essentially unchanged in early lemniscate shields with the exception of the complexity of additional hydraulic circuits to power a canopy tilt cylinder and canopy side-seals. The control of these fluid-powered functions was provided by direct manual control of valves energizing individual functions onboard the roof-support or the adjacent roof-support. This control valve-gear was comprised of multiple individual valves arranged in a "bank" or integrated into a single hydraulic distribution block with a single operating handle to select any independent function.

Jan 1, 1993

By R. K. Will

An inactive mining operation in northern California is known to be a source of acid mine drainage and heavy metals which have impacted adjacent creeks. Elevated concentrations of copper and zinc are a concern to aquatic populations, particularly steelhead trout and salmon downstream in the Sacramento River. Previous regional geological surveys of mineralization by the U.S. Geological Survey located and mapped outcrops of massive sulfides and gossan. Recent investigations indicate that a substantial amount of the metals in the local creeks are due to natural causes. The investigations include locating and mapping surface and subsurface minerals, soil and water sampling, and chemical analysis. Groundwater, seeps, and surface water were also sampled and analyzed. A water balance was conducted on a sub-basin level following delineation of surface water drainage and groundwater divides. A chemical mass balance incorporated metal concentrations and water volumes and was then used with other data to determine the contribution of metals from natural versus mining-related causes.

Jan 1, 1998

By S. Tuylu, D. Adiguzel, A. Bascetin, E. G. Savas, O. Ozdemir

"Paste Technology has some advantages comparing to other surface disposal methods. With this method, it is possible to pump high concentrated solid materials to very long distances without segregation problem. However, it is known from Literature that pumpability of materials is completely related to rheological properties of the materials. For this reason, in this study, the rheological parameters (e.g. yield stress and viscosity values) of the paste material prepared from Pb-Zn tailings at various solid ratios (60-85%) were obtained in order to determine the pumpability of the paste material. Additionally, slump tests, which are usually used in mining industry, was carried out. Finally, regression analysis was made between the slump values and rheological parameters of the paste material to find a correlation between two independent parameters. The results showed that there is a great correlation between the slump values and the yield stress of the material. On the other hand, there was no correlation with viscosity: ty=430.28-16.877Sv (R2= 0,94; ty: Yield Stress (Pa), Sv: Slump Value (cm)). Based on the results obtained from this study, it can be clearly concluded that the slump values obtained from a simple test can be used to predict yield stress values of paste materials. INTRODUCTION Recently, surface disposal of mining tailings has become one of the biggest problems in mining industry in terms of environmental issues. Therefore, several researches have been focused on this subject in order to find a best solution or method for this problem. These studies showed that paste technology has some advantages compared to other conventional methods. Tailings thickened to the extent show no segregation of particles during transportation, and relatively small amount of settling occur post-deposition which are often called “paste” (Cincilla et al. 1997). Paste tailing technology has two applications in the industrial area as underground paste fill and surface paste disposal. Paste tailing technology was first started to be used in Grund mine, Germany in the late 1970s (Grice, 1998). Process tailing material, water and - if needed - cement materials, which are the components of the paste, must be blended to obtain a homogenous mixture suitable for pumpability. Consistency behavior of the paste material is determined using a conventional sedimentation cone concrete test (slump). Meanwhile, the slump value of the paste must be between 200 and 250 mm for surface applications (Newman et al., 2001). Additionally, in the case of underground paste system, the optimum slump value must be between 150 and 200 mm. On the other hand, the water content and density of paste at certain slump value change depending on the amount of fine particles in the tailing sample. While moisture of the material will be high, its density will be low because of surface area of particles which increases with decrease in particle size (Meggyes and Debreczeni, 2006). For pumpability of the paste to long distances, slump value of the paste must be good enough to be accepted for use of surface paste disposal. Paste material has a yield stress because they show non-Newtonian behavior and generally is classified as a Bingham plastic fluid. (Cooke, 2008; Theriault, 2003). In addition, the appropriate viscosity value of the paste along with the yield stress must be between 100 and 250 Pa (Bascetin et al., 2013; Bascetin et al., 2014; Bascetin et al., 2015)."

Jan 1, 2016

By R. L. Guerguerian

Hydrostatic trunnion bearings were recently provided on large Semi-Autogenous Grinding (SAG) mills driven by wraparound motors assembled on the head to shell flanges. A conventional SAG mill would have a ring gear driven through one or two pinions. The effects of the magnetic air gap forces from this new SAG mill drive arrangement on the performance of the bearing are discussed. A step-by-step systematic analytical de-sign of the hydrostatic trunnion bearing is presented, followed by a discussion of grinding mill erection requirements to conform with the design. A brief comparison with other bearing types and their response to the effects of magnetic air gap forces are also presented.

Jan 1, 1992

By Rambabu Pothina, Rajive Ganguli

The economics of a mineral-processing circuit is dependent on the numerous sensors that are critical to optimization and control systems. When a sensor goes off calibration, it results in errors that can have a severe impact on plant economics. Classical statistical approaches fail to detect when errors are “subtle,” unless they grow and become large enough to be “gross,” whereas methods based on signal processing and artificial intelligence fail in dealing with the complexity of process fluctuations. Due to the sheer volume of sensors, undetected errors are not remedied until the next calibration, which on average are a year apart across all industries [1]. This research aims to detect such subtle errors (2 percent bias) in shorter time spans of about a month — rather than wait for errors to grow — using innovative data-mining techniques and algorithms.

By D. G. Purdy

Planning, as defined in Webster's New Collegiate Dictionary, is a detailed program of action designed to achieve an end. When developing a detailed plan to incorporate all the complex activities involved in a surface lignite mine, many elements must be carefully evaluated as to the individual and cumulative effects on the end result. The following elements are generally evaluated when planning a surface lignite mine: ? Reserve evaluation, including lignite quality characterization; ? Delineation of mining parameters, including lignite recovery factors, geotechnical factors, land control factors; ? Selection of mining blocks; ? Pit sequencing; ? Reclamation, including soil reconstruction design and land use planning; ? Overburden handling design; ? Selection of equipment; ? Sizing of equipment; ? Manpower requirements; and ? Other elements, including contract negotiations and execution, financing, investment return, operation economics, permitting and scheduling.

Jan 1, 1985

By Y. Jinnouchi

An air-pulsated jig has been widely adopted as a main coal washer. It may be mainly because of its many technical and economic features such as large capacity, low running cost, long life, etc. However, the recent increasing demand of fuel coal requires a higher productivity and efficiency of the air-pulsated jig. To fill this requirement theoretical and experimental investigations have been conducted on model and practical jigs in Japan. This paper generalizes the results of these investigations. In jig operation it is essentially of the most importance to create efficiently the pulsation of the water best suited for coal washing. The optimum pulsation should be determined by the theory of jigging process, and the method to realize it by that of pulsating mechanism.

Jan 1, 1982

By Bill Kendall

"In coal mines, handheld air, electric and hydraulic powered drills are used along belt conveyors, in single entry development, in entries where there are obstructions, and in longwall recovering bolting. In hard rock mines, pneumatically powered jackleg drills are typically used in narrow vein mining. Drilling and bolting in narrow confines has traditionally been performed with pneumatically or hydraulically powered hand-held drills or newer electrically powered hand- held hammer drills due to their low cost, simplicity of operation, and extreme flexibility due to their small size. Mechanized equipment has typically been too large, too expensive, inefficient due to the confined space, and too restrictive due to lack of flexibility for use in narrow confines.Although the handheld equipment is effective, it requires operator exposure to certain inherent hazardous conditions in use. These include falling rock from the roof, rib and face; tripping hazards; bending twisting lifting hazards; high noise levels and chemical fumes from the pneumatic exhaust. The operation of the hand held equipment can adversely affect the long-term health of the operator - continual jackleg operation frequently results in longterm damage to hearing, shoulders, arms and wrist joints and back injuries. This results in a reduction in life style for the operator and higher personnel turnover rates for the mining company.Hand-held drills also typically have limited thrust and torque capability that limits their ability to push long resin bolts, inadequate torque to properly install resin bolts or to properly torque mechanical or tensioned rebar bolts. Hand-held drills do not offer any type of protection for the operator from roof or rib falls. They do not offer any means for handling roof or rib mesh. Since the operator stands on the ground the maximum safe drilling height without use of a ladder or "riding the drill" is limited to 2.44 m (8 ft)."

Jan 1, 2014

By Glenn A. Shirey, Robert D. Stoessner, S. Gopalakrishnan

Under a contract awarded by the U.S. DOE-PETC, the Pennsylvania Electric Company and New York. State Electric and Gas Corporation are conducting a test program to evaluate and optimize the performance of a two-inch air-sparged. hydrocyclone (ASH) for cleaning fine coal. The test program is being conducted at the Homer City EPRI Coal Quality Development Center, utilizing Upper Freeport coal classified to minus 0.15 mm as the process feed material. A matrix of experiments has been conducted to establish the influence of significant design and operating variables (including overflow and underflow orifices, inlet slurry pressure, airflow rate, and reagent dosage) on the production of deep cleaned coal. Performance of the ASH is being compared to conventional froth flotation, utilizing advanced techniques and selected flotation reagents. This paper focuses on work completed to-date to optimize the performance of the air-sparged hydrocyclone for cleaning fine coal. INTRODUCTION The Pennsylvania Electric Company (Penelec) and New York State Electric and Gas Corporation (NYSEG) have been evaluating advanced fine coal cleaning processes for the production of compliance grade coal (1.2 pounds S02/million Btu). Laboratory bench-scale froth flotation results were compared with results of advanced flotation processes as performed by various organizations, utilizing the same coal feed. Among the processes evaluated, the air-sparged hydrocyclone (ASH) - developed by Dr. Jan Miller at the University of Utah - was considered to offer the best potential for retrofitting into an existing coal preparation facility because of the increased capacity per unit volume. The ASH has been shown to process over 100 times the throughput of conventional froth flotation cells. In May of 1988, Penelec/NYSEG was awarded a contract from the Department of Energy's Pittsburgh Energy and Technology Center (DOE-PETC) to optimize the performance of a five cm (two inch) ASH for producing compliance grade coal from raw classified minus 0.150 mm (1.00 mesh) Upper Freeport coal, and to compare its performance with conventional froth flotation utilizing advanced techniques and selected flotation reagents. The test work is being conducted at EPRI's Coal Quality Development Center (CQDC) in Homer City, Pennsylvania, utilizing a circuit processing 0.10 to 0.25 tons of coal per hour. Other members of the Penelec/NYSEG contract team include the University of Utah, Advanced Processing Technologies, Inc., Davy Dravo, Kaiser Engineers, Ebasco Services, and Management and Technical Systems. ASH DESCRIPTION AND OPERATION The ASH-2 System is a five cm ID (actually 4.76 cm) air-sparged hydrocyclone manufactured by Advanced Processing Technologies, Inc., under license from the University of Utah, for the purpose of research, evaluation and development. A schematic drawing of the air-sparged hydrocyclone is presented in Figure 1. Basically the air-sparged hydrocyclone consists of two concentric right-vertical tubes, a conventional cyclone header at the top, and a froth pedestal at the bottom. The inner tube is a porous tube through which air is sparged radially. The outer nonporous tube simply serves as an air jacket to provide for even distribution of air through the porous inner tube. The slurry is fed tangentially through the conventional cyclone header to develop a swirl flow in the radial direction. Air is sparged through the jacketed, inner porous tube wall and is sheared into small bubbles by the swirl flow. Hydrophobic particles in the slurry collide with these bubbles and, after attachment, are transported radially into a froth phase which forms on the cyclone axis. The froth phase is stabilized and constrained by the froth pedestal, thus moving towards the vortex finder of the cyclone header and discharged as an overflow product. Hydrophilic particles generally remain centrifuged in the slurry phase and are discharged as an underflow product through the annulus created by the froth pedestal.

Jan 1, 1989

By Nicole R. Henderson

Many mining engineering graduates enter the mining industry lacking training in mine emergency management. As a result, mining universities in the United Sates and other countries are beginning to form volunteer student mine rescue teams to train mining engineering students in handling mine emergency situations and give them hands-on experience managing potential emergency scenarios underground. In the early 1980s, the Missouri University of Science and Technology developed the first collegiate mine rescue team in the United States. For approximately 30 years, it was the only successful collegiate team until the Colorado School of Mines (CSM) started its program in 2009. Currently, there are at least five collegiate teams in the United States and one in Canada. At the Freiberg University of Mining and Technology in Germany, the goal is to adapt the Colorado School of Mines Mine Rescue Program to develop a collegiate team of its own. Currently, mining engineering students cover the theoretical basics of mine rescue in an occupational health and safety lecture and take a basic, one-day mine rescue training course at the Central Mine Rescue Station in Leipzig. The course covers the basic mine rescue topics and gives students the opportunity to experience working in elevated heat and smoke conditions while wearing breathing apparatus. This training gives students a small insight into the importance of mine rescue and mine emergency management. Collegiate mine rescue teaches students the importance of mine rescue and mine safety by giving them hands-on learning experiences before entering the mining industry.

Feb 1, 2014

By S. Tuylu, D. Adiguzel, U. G. Akkaya, A. Bascetin

"One of the main problems for storing of the tailings is acidity occurrence due to several factors such as existence of sulfuric minerals and also the pollution in seepage waters by mobilization of metal ions, which holds great risks in terms of environmental regulations. Because of these specified reasons, tailing materials to be used in a SPD formula should have comply with some specifications. Among these properties; oxygen content, temperature, matrix suction and pH are the most important parameters. In the study, the relationships between the parameters mentioned are investigated to reveal optimum paste design layout. The lowest amount of seepage water obtained from the paste layers in the pilot cabinet was found as 2150 ml from 3rd layer. As for the maximum seepage water and the average of the all 11 layers were found as 4909 ml from 6th layer and 3273 ml respectively. The reactions occurring according to the oxidation, as seen at seepage water of second and third layers, decreased the pH of system to the under of 7 value. Additionally, when the seepage water of first layer’s EC value is 2.93 mS/cm, the EC value of second layer is increased at 3.54 mS/cm. The other parameters are evaluated with the obtained results of the tests to determine the optimum storing conditions for SPD.INTRODUCTION Conventional waste disposal methods, although widely used, pose great environmental risks. One of the most important issues is acid mine drainage (AMD). Tailings of metallic mines contain heavy metals, aggressive chemicals and hazardous materials. In the presence of oxygen and water, an oxidation reaction can occur, causing a decrease in pH of the environment, and heavy metals that are present in the environment can dissolve easily. Subsequently, heavy metals can pollute underground water basins, creating a great amount of danger for the ecology and potable water resources. Another important risk associated with conventional waste disposal methods is accidents related to the waste dam. Higher volumes of water and tailings (usually 15% solids and 85% water by weight) are sent to waste dams, making it very difficult to control the stability of the dam under conditions such as static and dynamic loads (seismic activities, vibrations caused by blasting, etc.), flooding, and seepage. In case of an accident or failure, the spread of great amounts of mud containing hazardous chemicals and heavy metals can harm the environment of the dam site significantly (Bascetin et al., 2014). In the paste technology, depending on the type of ore, tailings used in the paste mixture can contain sulphide minerals (such as pyrite and pyrrhotite). These minerals are known to be reactive with water and oxygen to produce acidity (sulphuric acid)."

Jan 1, 2015

By H. J. Chen

In recent years, it has been recognized that the high horizontal stress is an important factor that contributes to a cutter roof. When the immediate roof is thinly bedded, the presence of a high horizontal stress may first cause failure on the bedding planes or weak planes, and then a cutter roof develops as the individual stratum crushes and buckles progressively layer by layer. In this study, the stress distributions in the bedding planes of the immediate roof are analyzed for an entry-pillar system in the multiple longwall panels by using the finite element method. Then the roof failure is analyzed based on the rock failure criterion and the stress distributions.

Jan 1, 1998

By S. S. Klima, J. A. Organiscak

Researchers at the National Institute for Occupational Safety and Health (NIOSH) performed laboratory testing to examine and improve airborne dust capture and methane removal performance of flooded-bed scrubbers on continuous mining machines using a blowing face ventilation configuration to reduce respirable dust exposure to shuttle car operators. Several testing conditions were examined to minimize shuttle car operator dust exposure without adversely affecting continuous miner performance and production. Curtain-to-face setback distance of 9.1 m versus 15.2 m (30 ft versus 50 ft), face ventilation airflow of 226.5 m3/min versus 339.8 m3/min (8,000 ft3/min versus 12,000 ft3/min), and the use of side-body-mounted blocking sprays (on versus off) were the three primary parameters compared. Scrubber airflow was set and maintained at 198.2 m3/min (7,000 ft3/min) throughout testing. An examination of slab cuts versus box cuts and the location of the shuttle car (present behind the continuous miner versus not present in the entry) was also performed to demonstrate the effects of these constantly changing scenarios on scrubber performance. Results show that the best blowing face ventilation setup for minimizing shuttle car operator dust exposure for the tested parameters uses a 15.2-m (50-ft) curtain-to-face setback with 339.8 m3/min (12,000 ft3/min) face ventilation while operating the side-body-mounted blocking sprays. INTRODUCTION Coal mine worker overexposure to respirable coal dust continues to be a problem in U.S. underground coal mining operations, potentially leading to coal workers’ pneumoconiosis (black lung). The U.S. Mine Safety and Health Administration (MSHA) requires that respirable dust exposure to coal mine workers does not exceed a 1.5 mg/m3 average over the actual working shift (79 Fed. Reg. 24814 (2014)). Although using a blowing face ventilation configuration on continuous miner (CM) sections is beneficial for removing methane emissions from the mining face, it can be detrimental for dust control for shuttle car (or ram car) operators and any other workers on the return ventilation side of the CM when compared to exhausting ventilation. Even with machine-mounted scrubbers on CMs, shuttle car operators still have some of the higher dust exposures with blowing face ventilation systems (NIOSH 2011, Beck et al. 2015). Although scrubber discharge air is not completely clean, dust being blown around the scrubber inlet and therefore not being captured by the scrubber can further increase these dust exposures (Goodman 2000). Dust control problems are also caused by inadequate face ventilation quantities causing scrubber face airflow recirculation issues (Schultz et al. 2010). In order to minimize respirable dust exposures on blowing face ventilation sections, ventilation, water spray, and scrubber parameters were experimentally examined to improve operating ranges for both dust and gas control. Several blowing face ventilation factors were examined with respect to CM spray systems and scrubber operation. Curtain-to-face setback distance and side-body-mounted blocking sprays were previously examined in the laboratory for dust control on a full-scale CM model using a scrubber on a blowing face ventilation system (Goodman 2000). The blocking sprays produced larger dust reductions at the CM’s rear corners and return for a 6.1-m (20-ft) curtain setback distance as compared to a 12.2-m (40-ft) curtain setback distance with equal face and scrubber airflows of 169.9 m3/min (6,000 ft3/min). Because face ventilation airflow quantities, shuttle car operator locations, and tracer gas concentration gradients were not previously examined during these experiments, additional research was required to determine improved operating parameters for blowing face ventilation systems.

Jan 1, 2019

By Jonathan G. Price

The 2011 report titled ?Energy Critical Elements: Securing Materials for Emerging Technologies? by the American Physical Society?s Panel on Public Affairs and the Materials Research Society surveys potential constraints on the availability of these elements and identifies five specific areas of potential action by the United States to ensure their availability: 1) federal agency coordination; 2) information collection, analysis and dissemination; 3) research, development and workforce enhancement; 4) efficient use of materials and 5) market interventions. Energy-critical elements (ECEs) are a class of chemical elements that currently are critical to one or more new energy-related technologies. A shortage of these elements would significantly inhibit large-scale deployment, which could otherwise be capable of transforming the way in which energy is produced, transmitted, stored or conserved. The report addresses elements that have not been widely extracted, traded or used in the past, and therefore are not the focus of well-established and relatively stable markets (such as carbon in coal or uranium as fuels, copper, aluminum, nickel and iron, all of which are clearly vital in energy applications).

Jan 1, 2011

By I. M. Arbuthnot

Over the last five years, a large number of small to medium sized carbon-in-pulp gold treatment plants have been built in Australia, most designed to treat between 250,000 -1,500,000 tpa of ore. In many cases, the primary requirement was to get a plant built and operating in a short period of time and at minimal capital cost, relating to the limited capital resources and tight cash flow positions of these relatively small mining companies. Since the inclusion of both pre-leach and tailings thickeners resulted in an obvious and significant capital cost, most plants were built without thickeners, without doing a detailed cost-benefit analysis on their inclusion, However, the increasing use of High Rate Thickener?s (HRT s) in the mineral processing industries resulted in a reassessment, in some cases, because of their considerably lower cost. This reassessment was triggered primarily by the need to conserve water in arid mining areas, where borefields were costly to install and water was limited. It has become apparent, though, since startup and operation of these installations, that the savings in cyanide consumption is also a very significant factor and can be used as a primary justification for the installation of a HRT in many cases.

Jan 1, 1991

By L. Xiao

Using K-oleate as a collector and alizarin red S (ARS) as a modifying agent, selective depression of dolomite from francolite was achieved in alkaline medium (pH> 9.0). Interestingly. ARS was also found to depress igneous apatite in alkaline medium in oleate flotation of apatite and calcite. Adsorption of ARS alone on dolomite was found to be higher than that on francolite. Complimentary adsorption experiments of ARS and K-oleate showed that oleate adsorption was increased in the presence of ARS on francolite but not on dolomite. K-oleate adsorbs on both francolite and dolomite and causes precipitation of calcium and magnesium oleate. Such precipitates can be pre-vented when ARS is present. The results are explained in terms of competitive adsorption for the active sites on francolite and dolomite by oleate and ARS, and their interactions with dis-solved mineral species in solution.

Jan 1, 1988

By D. Malhotra

The number of variables which can effect flotation of molybdenite is very large. This paper discusses the effect of two operating variables, namely, the degree of aeration and agitation, on the grade and recovery of molybdenite. A series of factorially designed flotation tests were carried out in a "Leeds Automatic Laboratory Flotation Cell." The analysis of flotation results indicate that molybdenite can be characterized into fast-floating and slow-floating components. The rates of fast-floating components, which do not create a problem in flotation, could be varied by changing agitation of airflow rates. However, the rate of slow-floating components was stable and was only a function of residence time in the float machine. The degree of aeration has a significant effect on the grade of MoS2 with only a slight effect on the recovery of MoS2. The degree of agitation has a slight effect on the grade, but does not effect the recovery of molybdenite. The implications of the results on the design of flotation cells and control and optimization of the existing circuits is subsequently discussed.

Jan 1, 1977